Manual PVM620
Contents
1. eere 11 APPENDIX A SPECIFICATIONSGS eere 13 This page intentionally left blank Chapter 1 Unpacking and Parts Identification Carefully unpack the instrument and accessories from the shipping container Check the individual parts against the list of components below If anything is missing or damaged notify TSI immediately 1 9 Carrying case Instrument Pressure tubing Static pressure tip USB cable CD ROM with downloading software This page intentionally left blank Chapter 1 Chapter 2 Setting up Supplying Power to the Alnor Model AXD620 Airflow Instruments PVM620 The Alnor AXD620 Airflow Instruments PVM620 is powered with four size batteries Installing the Batteries Insert four AA batteries as indicated by the diagram located on the inside of the battery compartment The Alnor AXD620 Airflow Instruments PVM620 is designed to operate with either alkaline or NiMH rechargeable batteries although it will not recharge NiMH batteries Battery life will be shorter if NiMH batteries are used Carbon zinc batteries are not recommended because of the danger of battery acid leakage Using the Optional AC Adapter When using the AC adapter the batteries if installed will be bypassed Be sure to provide the correct voltage and frequency which is marked on the back of the AC adapter The AC adapter will not recharge the batteries Connect2. ACTUAL STANDARD SETUP Choose Actual Standard measurements and parameters in the Act Std Setup menu Within this menu you can also select Standard Temperature Standard Pressure and a source for the actual temperature The actual barometric pressure must be entered to convert air velocity and volume measurements to actual conditions The Entered Temp range is from 40 to 1832 F 40 to 1000 C DATA LOGGING Measurements Measurements to be logged are independent of measurements on the display and must therefore be selected under DATA LOGGING gt Measurements e When set to ON measurement will be logged to memory e When set to DISPLAY measurement will be logged to memory if itis visible on the main running screen e When set to OFF measurement will not be logged to memory Operation 7 Log Mode Log Settings You can set Log Mode to Manual Auto save or Cont key e Manual mode does not automatically save data but instead prompts you to save a sample e In Auto save mode you manually take samples that are automatically logged e In Cont key mode you start taking readings and logging by pressing the key The instrument will continue taking measurements until the key is pressed again e Auto save and Cont Key modes have the following additional Log Settings Mode Log Settings Auto save Log Interval Cont key Log Interval e Pressing the A V keys simultaneously will lock the keypad to prevent unauthori
3. g This warranty is VOID if the product has been misused neglected subjected to accidental or intentional damage or is not properly installed maintained or cleaned according to the requirements of the manual Unless specifically authorized in a separate writing by Seller Seller makes no warranty with respect to and shall have no liability in connection with goods which are incorporated into other products or equipment or which are modified by any person other than Seller The foregoing is IN LIEU OF all other warranties and is subject to the LIMITATIONS stated herein NO OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR PARTICULAR PURPOSE OR MERCHANTABILITY IS MADE WITH RESPECT TO SELLER S BREACH OF THE IMPLIED WARRANTY AGAINST INFRINGEMENT SAID WARRANTY IS LIMITED TO CLAIMS OF DIRECT INFRINGEMENT AND EXCLUDES CLAIMS OF CONTRIBUTORY OR INDUCED INFRINGEMENTS BUYER S EXCLUSIVE REMEDY SHALL BE THE RETURN OF THE PURCHASE PRICE DISCOUNTED FOR REASONABLE WEAR AND TEAR OR AT SELLER S OPTION REPLACEMENT OF THE GOODS WITH NON INFRINGING GOODS TO THE EXTENT PERMITTED BY LAW THE EXCLUSIVE REMEDY OF THE USER OR BUYER AND THE LIMIT OF SELLER S LIABILITY FOR ANY AND ALL LOSSES INJURIES OR DAMAGES CONCERNING THE GOODS INCLUDING CLAIMS BASED ON CONTRACT NEGLIGENCE TORT STRICT LIABILITY OR OTHERWISE SHALL BE THE RETURN OF GOODS TO SELLER AND THE REFUND OF THE PURCHASE PRICE OR AT THE OPTION OF SELLER THE REPAIR OR REPLACEMENT OF THE GOOD
4. 1980588 Rev D ALNOR 02014 TSI Incorporated e AIRFLOW INSTRUMENTS Airflow Instruments TSI Instruments Ltd Visit our website at www airflowinstruments co uk for more information UK Tel 44 149 4 459200 France Tel 33 491 11 87 64 Germany Tel 49 241 523030 Printed in U S A
5. MICROMANOMETER ALNOR MODEL AXD620 AIRFLOW INSTRUMENTS MODEL PVM620 OPERATION AND SERVICE MANUAL P N 1980588 REV D DECEMBER 2014 ALNOR A nrLow START SEEING THE BEMPELS UF REGISTERING TODAY Thank you for your TSI instrument purchase Occasionally TSI releases information on software updates product enhancements and new products By registering your instrument TSI will be able to send this important information to you http register tsi com As part of the registration process you will be asked for your comments on TSI products and services TSI s customer feedback program gives customers like you a way to tell us how we are doing e UNDERSTANDING ACCELERATED e TSI Incorporated Visit our website www tsi com for more information USA Tel 1 800 874 2811 India Tel 91 80 67877200 UK Tel 44 149 4 459200 China Tel 86 10 8219 7688 France Tel 33 4 91 11 87 64 Singapore Tel 65 6595 6388 Germany Tel 49 241 523030 2013 TSI Incorporated Printed in U S A Copyright TSI Incorporated 2007 2014 All rights reserved Address TSI Incorporated 500 Cardigan Road Shoreview MN 55126 USA Fax No 651 490 3824 Limitation Of Warranty And Liability effective April 2014 For country specific terms and conditions outside of the USA please visit www tsi com Seller warrants the goods excluding software sold hereunder under normal use and service as described in the operat
6. S IN THE CASE OF SOFTWARE SELLER WILL REPAIR OR REPLACE DEFECTIVE SOFTWARE OR IF UNABLE TO DO SO WILL REFUND THE PURCHASE PRICE OF THE SOFTWARE IN NO EVENT SHALL SELLER BE LIABLE FOR LOST PROFITS BUSINESS INTERRUPTION OR ANY SPECIAL INDIRECT CONSEQUENTIAL OR INCIDENTAL DAMAGES SELLER SHALL NOT BE RESPONSIBLE FOR INSTALLATION DISMANTLING OR REINSTALLATION COSTS OR CHARGES No Action regardless of form may be brought against Seller more than 12 months after a cause of action has accrued The goods returned under warranty to Seller s factory shall be at Buyer s risk of loss and will be returned if at all at Seller s risk of loss Buyer and all users are deemed to have accepted this LIMITATION OF WARRANTY AND LIABILITY which contains the complete and exclusive limited warranty of Seller This LIMITATION OF WARRANTY AND LIABILITY may not be amended modified or its terms waived except by writing signed by an Officer of Seller Service Policy Knowing that inoperative or defective instruments are as detrimental to TSI as they are to our customers our service policy is designed to give prompt attention to any problems If any malfunction is discovered please contact your nearest sales office or representative or call Customer Service department at 44 0 149 4 459200 Uk 800 874 2811 USA or 1 651 490 2811 International CONTENTS CHAPTER 1 UNPACKING AND PARTS IDENTIFICATION 1 CHAPTER 2 SETTING UD kk kek
7. ange is a function of actual velocity pressure duct size and K factor Instrument Temperature Range Operating 40 to 113 F 5 to 45 C Storage 4 to 140 F 20 to 60 C Instrument Operating Conditions Altitude up to 4000 meters Relative humidity up to 80 RH non condensing Pollution degree 1 in accordance with IEC 664 Transient over voltage category II Data Storage Capabilities Range 12 700 samples and 100 test IDs Logging Interval Intervals 1 second to 1 hour Time Constant Intervals User selectable External Meter Dimensions 3 3 in x 7 0 in x 1 8 in 8 4 cm x 17 8 cm x 4 4 cm Meter Weight Weight with batteries 0 6 lbs 0 27 kg 13 Power Requirements Four AA size batteries included or AC adapter optional 9 VDC 300 mA 4 18 watts input voltage and frequency vary depending on which adapter is used Overpressure range 7 psi 190 in 360 mmHg 48 kPa Pressure velocity measurements are not recommended below 1 000 ft min 5 m s and are best suited to velocities over 2000 ft min Range can vary depending on barometric pressure Accuracy is a function of converting pressure to velocity Conversion accuracy improves when actual pressure values increase 14 Appendix A e Alnor Products TSI Incorporated Visit our website www alnor com for more information USA Tel 1 800 874 2811 India Tel 91 80 67877200 China Tel 86 10 8219 7688 Singapore Tel 65 6595 6388 P N
8. cs average minimum maximum and count are calculated for each test ID The maximum number of test IDs is 100 Time Constant The time constant is an averaging period It is used to dampen the display If you are experiencing fluctuating flows a longer time constant will slow down those fluctuations The display will update every second but the displayed reading will be the average over the last time constant period For example if the time constant is 10 seconds the display will update every second but the displayed reading will be the average from the last 10 seconds This is also referred to as a moving average Log Interval The logging interval is a frequency period that the instrument will log readings For example if the logging interval is set to 30 minutes each sample will be the average of the last 30 minutes Menus DISPLAY SETUP Display setup menu is where you will setup the desired parameters to be displayed on the running screen With a parameter highlighted you can then use the ON soft key to have it show up on the running screen or select the OFF soft key to turn off the parameter Use PRIMARY soft key to have a parameter show up on the running screen in a larger display Only one parameter can be selected as a primary and up to 2 secondary parameters can be selected at one time PRESSURE ZERO To zero the pressure reading select the Pressure Zero menu The instrument will i
9. ing to a Computer Use the Computer Interface USB Cable to connect the instrument to a computer For information on how to download stored data see Chapter 3 LogDat2 Downloading Software of the Alnor AXD620 Airflow Instruments PVM620 is not intended for connection to a public telecommunications network Connect the USB data port only to another USB port G Caution This symbol is used to indicate that the data port This page intentionally left blank Chapter 2 Chapter 3 Operation Keypad Functions ON OFF Key Press to turn the Alnor Model AXD620 Airflow Instruments PVM620 on and off During the power up sequence the display will show the following Model Number Serial Number and Software Revision Arrow A V Keys Press to scroll through choices while setting a parameter Enter Key Press to accept a value or condition Arrow or gt and Menu Soft Keys Press arrow keys to change choices while setting a parameter Press the Menu soft key to select the Menu selections which are Display Setup Pressure Zero Settings Flow Setup Actual Std Set up Data Logging and Calibration Common Terms In this manual there are several terms that are used in different places The following is a brief explanation of the meanings of those terms Sample Consists of all of the measurement parameters stored at the same time Test ID A group of samples The statisti
10. kak ek kk KAK KA KAK KA KAWA KA WA 3 Supplying Power to the Alnor Model AXD620 Airflow Instruments mur EE 3 Installing the Batteries L kk 3 Using the Optional AC 3 Connecting to a 3 CHAPTER 3 OPERATION kk kk kK KAKE KA KAKA WARA 5 Keypad D K F r KE KARN nnn nnns 5 Common Terms TY YY EE Rewan 5 le B N YE eve E D YE 6 DISPEAY SE TUB hal Ie Kek RR nie 6 PRESSURE ZERO 4 k n ree y r ferrc er docnit fe y ka ada yan 6 SETTINGS Ires tiende eee der Ea k ke Ek ek 6 FLOW SETUPS scout edt k yeki eee ata ee eee aee etaed 7 ACTUAL STANDARD SETUP 7 DATA LOGGING ttt cy dade eatin 7 7 Log Mode Log Settings 8 Delete Dala dikn T d ded is 8 Yo MEMO cas 8 LogDat2 Downloading 8 CHAPTER 4 MAINTENANCE ccccsseceeesseeceensseeeeenseseeeenseeeeeenas 9 Recalibratioriz i Te e eMe tag HERR Yarek de ns 9 dieu detecte du tede adt etu deckt atte trea 9 c qe leeets 10 CHAPTER 5 TROUBLESHOOTING
11. ll out an online RMA form visit TSI s website at http service tsi com U S amp International UK TSI Incorporated TSI Instruments Ltd Alnor Products Stirling Road 500 Cardigan Road Cressex Business Park Shoreview MN 55126 3996 High Wycombe Tel 800 874 2811 Bucks 651 490 2811 HP12 3ST United Kingdom Fax 651 490 3824 Tel 44 0 149 4 459200 Fax 44 0 149 4 459700 The Alnor Model AXD620 Airflow Instruments PVM620 can also be recalibrated in the field using the CALIBRATION menu These field adjustments are intended to make minor changes in calibration to match a user s calibration standards The field adjustment is NOT intended as a complete calibration capability For complete multiple point calibration and certification the instrument must be returned to the factory Cases If the instrument case or storage case needs cleaning wipe it off with a soft cloth and isopropyl alcohol or a mild detergent Never immerse the Alnor Model AXD620 Airflow Instruments PVM620 If the enclosure of the Alnor Model AXD620 Airflow Instruments PVM620 or the AC adapter becomes broken it must be replaced immediately to prevent access to hazardous voltage Storage Remove the batteries when storing the unit for more than one month to prevent damage due to battery leakage 10 Chapter 4 Chapter 5 Troubleshooting Table 5 1 lists the symptoms possible causes and reconmended solutions for common problems encou
12. ndicate if the pressure zero was successful SETTINGS Settings menu is where you can set the general settings These include Language Beeper Select Units Time Constant Contrast Set Time Set Date Time Format Date Format Number Format Backlight and Auto Off Use the lt or gt soft keys to scroll through the settings for each option and use the key to accept settings 6 Chapter 3 FLOW SET UP In Flow Setup mode there are four types Round Duct Rectangle Duct Duct Area and K Factor Use the lt or gt soft keys to scroll through the types and then press the key to accept the desired type To change the setting highlight the Enter Settings option and press the key Press Kfact allows for calculating flow rate from diffusers or flow stations with pressure taps using the instruments pressure ports and K factors The K factors are obtained from the diffuser or flow station manufacturer For more information refer to Application Note TSI 114 e Up to 5 K factors can be pre programmed for quick use e When Flow is set as the Primary measurement in the Display Setup menu the K factor will also be displayed When measuring Flow as the Primary measurement the parameters can be quickly changed by pressing the A or W key while on the main measurement screen Make adjustments with the amp or W arrow keys and press 1 to accept or enter the Select Kfactor menu to choose a different pre programmed flow value
13. ntered with the Alnor Model AXD620 Airflow Instruments PVM620 If your symptom is not listed or if none of the solutions solves your problem please contact TSI Table 5 1 Troubleshooting the Alnor Model AXD620 Airflow Instruments PVM620 Symptom Possible Causes Corrective Action No Display Low or dead batteries ee nee contacts Reading Fluctuating flow Reposition probe in fluctuates less turbulent flow or unstable use longer time constant No response to Keypad locked out Unlock keypad by keypad pressing A Y keys simultaneously Instrument Error Memory is full Download data if message appears desired then DELETE ALL memory required on instrument The pressure sensor is protected from damage up to 7 psi 48 kPa or 360 mmHg At higher pressure it can burst 11 12 This page intentionally left blank Chapter 5 Appendix A Specifications Specifications are subject to change without notice Static Differential Pressure Range 15 to 15 in H20 28 0 to 28 0 mm Hg 3735 to 3735 Pa Accuracy 1 of reading 0 005 in H O 0 01 mm Hg 1 Pa Resolution 0 001 0 1 Pa 0 01 mm Hg Velocity From a Pitot Tube Range 250 to 15500 ft min 1 27 to 78 7 m s Accuracy 1 5 at 2000 ft min 10 16 m s Resolution 1 ft min 0 1 m s Duct Size Range 1 to 500 inches in increments of 0 1 in 2 5 to 1270 cm in increments of 0 1 cm Volumetric Flow Rate Range Actual r
14. or s manual to be free from defects in workmanship and material for 24 months or if less the length of time specified in the operator s manual from the date of shipment to the customer This warranty period is inclusive of any statutory warranty This limited warranty is subject to the following exclusions and exceptions a Hot wire or hot film sensors used with research anemometers and certain other components when indicated in specifications are warranted for 90 days from the date of shipment b Pumps are warranted for hours of operation as set forth in product or operator s manuals c Parts repaired or replaced as a result of repair services are warranted to be free from defects in workmanship and material under normal use for 90 days from the date of shipment d Seller does not provide any warranty on finished goods manufactured by others or on any fuses batteries or other consumable materials Only the original manufacturer s warranty applies e This warranty does not cover calibration requirements and seller warrants only that the instrument or product is properly calibrated at the time of its manufacture Instruments returned for calibration are not covered by this warranty f This warranty is VOID if the instrument is opened by anyone other than a factory authorized service center with the one exception where requirements set forth in the manual allow an operator to replace consumables or perform recommended cleaning
15. zed adjustments to the instruments To unlock the keypad press the A W keys simultaneously Delete Data Use this to delete all data delete test or delete sample Memory This option displays the memory available Delete All under Delete Data will clear memory and reset the memory available LogDat2 Downloading Software The Alnor AXD620 Airflow Instruments PVM620 comes with special software called LogDat2 Downloading Software which is designed to provide you with maximum flexibility and power To install this software on your computer follow the instructions on the label of the LogDat2 CD ROM To download data from the Alnor AXD620 Airflow Instruments PVM620 connect the supplied computer interface USB cable to the Alnor AXD620 Airflow Instruments PVM620 and to a computer USB port Then run the LogDat2 downloading software Within the LogDat2 software either select the tests to be downloaded or double click on a test to open it 8 Chapter 3 Chapter 4 Maintenance The Alnor Model AXD620 Airflow Instruments PVM620 requires very little maintenance to keep it performing well Recalibration To maintain a high degree of accuracy in your measurements we recommend that you return your Alnor Model AXD620 Airflow Instruments PVM620 to TSI for annual recalibration Please contact one of TSI s offices or your local distributor to make service arrangements and to receive a Return Material Authorization RMA number To fi
Download Pdf Manuals
Related Search