CA-9 (Top-Snacks) Service Manual
Contents
1. The Voice Module comes with a prerecorded message such as Hey how about a soda or maybe a snack But you can record your own Figure 10 Optional Voice Module Battery se Voice Box Light Sensor Red LED Microphone 1 To record a new message A Remove the Voice Module and turn it so the Microphone is facing you B Press the Record Button and begin speaking The Red LED will light up You have 10 seconds of recorded time available C Release the Record Button the message will play back to you Figure 11 Coin Rejecter Fingers Figure 11a Caught Figure 11b Accepted Figure 11c Vend Empty Coin Discs should Coins should push the Accepted coins push the catch on the center of the fingers out Make sure fingers over the Coin Coin Rejector fingers coins contact the center Discs catches to vend of the fingers GENERAL NOTES It is suggested that a tool box accompany you to each of your locations Suggested items for this tool box would include a socket set up to a 1 2 socket size suggested a Phillips and a Standard screwdriver Additional items would be a small jar of Petroleum Jelly such as Vaseline a small brush for applying the Petroleum Jelly a soft rag and perhaps a black permanent marker The black marker is useful in touching up light scratches that may occur to your vendor COMMON QUESTIONS AND ANSWERS MAINTENANCE Q My knob turns without coins A Your Coin Rejecter2. C Pull the Mechanism Panel outward Carefully free Drivers from all Helix Coils D Turn desired Mechanism Knob clockwise 1 turn and place Mechanism Panel face down on a flat surface exposing the Driver Mechanism and S bracket assembly Fig 7 Note Change one Driver Mechanism at a time E To change Driver Mechanisms remove two 2 nuts Fig 5 and gently remove S Bracket Assembly F Unscrew and remove the two 2 Screws holding Driver to the Coin Sub Assembly Fig 5 amp Fig 6 G Coin Sub Assembly Fig 4 amp Fig 6 will come apart from Knob and can be carefully removed 2 To assemble Driver Mechanism A Lubricate backside of Mechanism Panel around holes with a small amount of petroleum jelly B Insert two 2 screws through Coin Sub Assembly to Knob Make sure Knob is seated properly and tighten screws into place If handle is hard to turn loosen the two 2 screws 1 8 to 1 4 turn C Turn mechanism Knob to align Coin Discs with S bracket mounting studs Install S bracket assembly over mounting studs Do not install the nuts yet D Now turn Mechanism Knob so Coin Disc slots are facing down The Anti Reverse Dog can now be raised To Purchase This Item Visit BMI Gaming www bmigaming com 1 800 746 2255 1 561 391 7200 Figure 5 Inside view of Driver Mechanism S Bracket Assembly Driver Mechanism Coin Deflector T4 Screws enough to enable the Anti Reverse Dog Spring to seat u
3. is loose misaligned or broken Refer to the Driver Mechanism section of this manual for proper placement of the Coin Rejecter See Fig 7 amp Fig 11 Q My mechanism screws keep coming loose A Remove Mechanism Panel Disassemble Knob Apply Lock Tight to Knob screw threads If this does not remedy the problem a replacement knob may be needed My mechanism rotates backward Your Knob should not do this Remove the Mechanism Panel and check for zO zO zO PFO zO zO zO To Purchase This Item Visit BMI Gaming www bmigaming com 1 800 746 2255 1 561 391 7200 proper placement and condition of the Anti Reverse Dog My mechanism rotates but product will not drop Check to see if the product is jammed in the Column Check to see if the vendor is level Check product for damage and make sure it is the proper size My knob turns 14 turn and jams First remove your Mechanism Panel Check the position of the coins to see if they are in between the Coin Rejecter fingers If this is the case place a screwdriver in between the Coin Rejecter and the discs and lift up freeing the Coin Rejecter At this point the Driver Mechanism can now be rotated backwards Reposition the Coin Rejecter fingers with your screwdriver to line up with coins and vend through Fig 10 GENERAL Can customers reach up and help themselves to product No The Vendor pushes product out the back of the Product Trays My key won t turn my
4. Lock to open Check to be sure that you are using the proper key If the correct key is being used your Lock may have been damaged or vandalized Vandalism to locks is quite common Having spare Locks in your toolbox at all times is recommended What can use to clean the outside of my vendor A lint free rag and a mild window cleaner are recommended Be sure however not to directly spray decals as the ink could run How do remove a Lock that won t open Drill into the center of the Lock with a 1 4 drill bit The Lock should fall apart and be easily removed Increase the bit size and try again if the Lock does not come out Why is my Voice Module silent Make sure the Voice Module is turned on Record a new message Replace the batteries Can the Voice Module store more than one message No The Voice Module can only store 10 seconds of record time Figure 12 Optional 60 configuration yore Quarter Disc Dime Disc ST110 Black Spacer ST105 ST107 ST104 NA HA Ratchet Disc TEUA Screws CP SS112 O Black Spacer ST104 White Spacer Knob ST108 BL iba Mechanism Panel To Purchase This Item Visit BMI Gaming www bmigaming com 1 800 746 2255 1 561 391 7200 Figure 13 Optional 65 configuration Driver Quarter Disc Dime Disc Nickel Disc J ST110 ST105 ST107 vu er BN O Ratchet S T103 Screws Disc SS112 RAT Z n Black Spacer 40 ST104 White Spacer Knob 3 ST108 Pito Mechani
5. To Purchase This Item Visit BMI Gaming www bmigaming com 1 800 746 2255 1 561 391 7200 9 SEAGA 9 10 Column Mechanical Snack Vendor Pe CRORE PI cee Operator s Manual Seaga Manufacturing Inc 700 Seaga Drive Freeport IL USA 61032 www seagamfg com To Purchase This Item Visit BMI Gaming www bmigaming com 1 800 746 2255 1 561 391 7200 INTRODUCTION Congratulations on the purchase of your new Snack Vendor This Snack Vendor has been designed to give you many years of dependable service It requires little maintenance and is easy to set up and operate READ THIS MANUAL COMPLETELY Your Snack Vendor is designed to operate simply and reliably but to take full advantage of your vendor please read this owner s manual thoroughly It contains important information regarding installation and operations as well as a brief troubleshooting guide EQUIPMENT INSPECTION After you have received your Snack Vendor and have it out of the box place it on a secure surface for further inspection Note Any damages that may have occurred during shipping must be reported to the delivery carri er immediately Reporting damages and the seeking of restitution is the responsibility of the equipment owner The factory is willing to assist you in this process in any way possible Feel free to contact our Customer Care Department with any questions you may have on this process Once you have your vendor located we suggest that you keep this man
6. and permanently to the vendor is at the owner s discretion Figure 1 Optional Stand Assembly Side Supports Nee te Rear Leg Small arrows indicate direction for inserting bolts Front Rear Supports Leg detail Note Front Legs are folded over on both ends Your vendor can be mounted to the 5 select mechanical soda vendor to form the Mechanical Combination Vendor The vendor comes with mounting hardware You will need tools for mounting 1 To Mount the snack vendor to the soda vendor B Set the snack vendor on top of soda vendor C Unlock and open the Front Door of the snack vendor The beverage vendor does not need to be opened The following is to be done inside the snack vendor D Remove bottom Product Tray Pull Product Tray fully forward and out E Attach the snack vendor to the top of the soda vendor Insert the two 2 Phillips head screws down through the snack vendor into the threaded holes in the top of the soda vendor F Reassemble Front Legs Figure 2 Optional Soda Vendor Mount Snack Vendor Lower Product Tray Phillips mounting Remove screws Soda Vendor Vend Area Mounting holes To Purchase This Item Visit BMI Gaming www bmigaming com 1 800 746 2255 1 561 391 7200 DELIVERY SYSTEM Your new snack vendor features a rear drop delivery system to prevent theft The snack vendor delivery system is made up of three 3 components the Product Tray the He
7. anel eee BILE Lock Coin Mechanism Knob Delivery Chamber Mechanism Panel and Product Tray Optional Vend Area Coin Box Voice Module 10 column not shown To Purchase This Item Visit BMI Gaming www bmigaming com 1 800 746 2255 1 561 391 7200 LOCKS Your vendor has one 1 screw type Lock To unlock the Front Door unscrew the Lock counter clockwise until the door is free To lock apply firm pressure below the Lock as you tighten the Lock Do not over tighten as you could ruin the seal You will be able to remove the key only when the key is vertical or horizontal MOUNTING optional Your vendor offers you many flexible options within your vending environment The vendor allows the versatility of a stand alone countertop vendor mounting to the optional stand Fig 1 additionally it may be mounted to the 5 select mechanical soda ven dor which allows for optimum use of floor space within the vending environment Mounting to the soda vendor offers your cus tomers the variety of cold beverages along with their snack purchase 1 To assemble the CTS stand A Attach Legs to short side supports as shown in Fig 1 by inserting bolts through Legs and then attaching support to inside of Leg with nuts B Once both ends are assembled attach Front Rear Supports in same manner one end at a time C Vendor sits atop stand and is held in place by the Rear Legs Note The vendor rests on the stand attaching the st
8. lix Coils and the Coin Mechanism Fig 3 Once the proper amount of coins is received the Coin Mechanism drives the Helix Coil and pushes the product out the back of the Product Tray Figure 3 Delivery System Product Tray Helix Coil ____ Driver Mechanism DRIVER MECHANISM The Mechanism Panel is the front panel This panel controls the receiving of money and the action of the Helix Coil Once the correct amount of money is received the Mechanism Knob can be turned clockwise to the right Product is vended by turning the Mechanism Knob one 1 complete revolution The Driver Mechanism Fig 4 comes factory preset but can be changed to suit your needs The Coin Sub Assembly is made up of a series of discs consisting of white black and metal Coin Discs The white spacers are thinner than the black and the combination of the two place the Coin Discs in the proper position to receive coins Figure 4 Driver Mechanism reference All discs are the Coin Sub Assembly From Knob to Driver is the Driver Mechanism In some cases you will find all one 1 color of spacers This is common in an all quarter configuration Contact our Customer Care Department for additional instructions on changing your Coin Sub Assembly if necessary 1 To access Coin Mechanism A Unlock and remove Front Door B Remove the Mechanism Panel by first removing the two 2 Silver Screws on both sides of the Mechanism Panel
9. nder the Anti Reverse Dog At the same time the S bracket assembly will be seated against Mechanism Panel Place Keps Nut on upper mounting stud DO NOT TIGHTEN NUTS Fig 4 amp Fig 6 E Turn Knob to align coin discs with S bracket assembly once again Use a screwdriver to push top of S bracket assembly fully to right and tighten Keps Nut You may now tighten Nylon Threaded Nut to lower mounting stud DO NOT OVER TIGHTEN Note The fingers of the Coin Rejecter must align with Coin Discs of the Coin Sub Assembly The Coin Discs strike the center of each finger to prevent vending without coins This alignment is critical If the fingers are misaligned the vendor will not vend Fig 8 Figure 6 Driver Mechanism exploded view Driver ST110 P Black Spacer Quarter Disc N Pe ST104 S1103 Ratchet Disc ST103 Screws SS112 Knob 4 PL104 Black Spacer ST104 Standard Mechanism White Spacer 50 configuration F Check to see that S bracket assembly is firmly seated against Mechanism Panel and upper mounting stud Check that Anti Reverse Dog Spring is engaged on Anti Reverse Dog Make sure Anti Reverse Dog moves freely and locks into Ratchet Disc as the mechanism is rotated counter clockwise If Anti Reverse Dog does not move freely loosen Nylon Threaded Nut on the lower mounting stud If this does not help remove S bracket assembly Figure 7 S Bracket Assembly Keps Nut Nylon SS206 Threaded Nut Anti Re
10. rchantability and fitness or use and of all other obligations or liabilities on Manufacturer s part Manufacturer neither assumes nor authorizes any other person to assume for it any other liability in connection with the sale of equipment manufactured by itself This war ranty shall not apply to equipment manufactured or any part thereof which is subject to accident negligence alteration abuse misuse or damage in shipment The term original purchaser as used in this warranty shall be deemed to mean that person for whom the equipment is originally installed Manufacturer is not liable for any incidental consequential or other damages of any kind whatsoever directly or indirectly arising from the use of the equipment whether based upon theories of contract negligence or tort Effective 9 01 For Technical Support amp Service For Parts Contact our Customer Care Dept Contact our Parts Dept 8 30 a m 4 00 p m CST Mon thru Fri 8 30 a m 4 00 p m CST Mon thru Fri 815 297 9500 ext 160 815 297 9500 ext 160 815 297 1758 Fax 815 297 1758 Fax email customercare seagamfg com email parts seagamfg com Seaga Manufacturing Inc 700 Seaga Drive SEAGA Freeport IL 61032 U S A Online www seagamfg com To Purchase This Item Visit BMI Gaming www bmigaming com 1 800 746 2255 1 561 391 7200 9 10 Column Mechanical Snack Vendor Front Door Product Window e W _ a TA spat Mechanism DS ie Gy a r P
11. sized item into the Helix Coil or Column or attempt to vend an item that is smaller than the Helix Coil as this will create problems and deter customers 1 To Load Product A Pull Product Tray forward B Place product in proper size Helix Coil Note Bottom of product must rest on the Product Tray and not on the Helix Coil Fig 9 Load each Helix Coil from back to front Note Fill all Helix Coils fully do not leave any empty spaces behind or between items If you must leave empty space leave it in the front of the Tray closest to the Product Window C Once Product Tray is fully loaded lift and push it back in Special Note We suggest that you always partially fill the vendor with product and perform at least five 5 test vends Figure 9 Loading Product Rear view Correct load product between Helix Coils resting on the product tray eae a on A Incorrect Helix Coil ad i w Columns COIN RETRIEVAL One 1 Coin Box is provided with your vendor They are stored below the Product Tray directly behind and below the Coin Mechanisms Once the Front Door is open pull out the product tray and then pull the Coin Box out to the right to empty it To Purchase This Item Visit BMI Gaming www bmigaming com 1 800 746 2255 1 561 391 7200 OPTIONAL TALKING VENDOR The snack vendor can be equipped with a Voice Module to increase sales The Voice Module consists of three parts the Voice Box the Battery Tray and the Record Button
12. sm Panel Figure 14 Optional 70 configuration Driver Quarter Disc Dime Disc si _ a PA cx ug Ratchet Disc kia ST103 J Screws K SS112 Black Spacer ST104 White Spacer Knob ST108 Piod Mechanism Panel Figure 15 Optional 75 configuration Driver Quarter Disc ST110 Black Spacer ST105 A P ST104 Ratchet Disc ST103 Knob PL104 Black Spacer ST104 White Spacer ST108 Mechanism Panel To Purchase This Item Visit BMI Gaming www bmigaming com 1 800 746 2255 1 561 391 7200 Figure 16 Optional 80 configuration Driver Quarter Disc PAR Nickel Disc ST105 ST106 we a Ratchet Disc sl Screws SS112 Black Spacer ST104 White Spacer Knob To ST108 Bod Mechanism Panel Figure 17 Optional 1 00 configuration l Driver Quarter Disc erady ST105 ZA ae Za cyt y a Ratchet Disc N T Screws ST112 Black Spacer ST104 White Spacer Knob ae ST108 PL 104 Mechanism Panel
13. ual for future reference or you can view this manual online at www seagamfg com Should any problems occur refer to the section entitled COMMON QUESTIONS AND ANSWERS It is designed to help you quickly identify a problem and correct it MANUFACTURER S WARRANTY WHAT IS COVERED Manufacturer warrants TO THE ORIGINAL PURCHASER ONLY that each item of equipment manufactured is free from defects in material and workmanship under normal use and service Manufacturer s obligation under this warranty shall be limited to repair or replacement at our plant of any parts of the equipment which shall within one year of the date of shipment to the original purchaser be demonstrated to be defective The original purchaser may obtain repair or replace ment of the equipment under this warranty by returning the defective item or entire vendor to the Manufacturer freight pre aid WHAT IS NOT COVERED Manufacturer s warranty obligations DO NOT EXTEND TO OR INCLUDE installation expenses vandalism or difficulties resulting from failure to operate equipment in accordance with Manufacturer s instructions under competent supervision and difficulties due to changes in vended products which are beyond the control of Manufacturer SPECIAL NOTE Manufacturer is not responsible for any loss of income due to a vending machine being out of service due to a warrantable item This warranty is in lieu of all other warranties expressed or implied including the warranty of me
14. verse SS207 ae Dog Spring Coin Rejecter S Bracket ST202 ST201 oe sp 2 Anti Reverse Arii 2 a ee To Purchase This Item Visit BMI Gaming www bmigaming com 1 800 746 2255 1 561 391 7200 and close Anti Reverse Dog Spring to put more pressure on Anti Reverse Dog Check that coin discs are properly aligned with the Coin Rejecter by inserting money through slots in the top of the Mechanism Panel Make sure the Coin Rejecter is properly engaging the coin disc stops Improper alignment will allow coins to slip between slots in the Coin Rejecter Refer to the optional mechanism configurations at the end of this manual Always make sure your Driver Mechanism is built as specified in the diagram Note The disc next to the Driver is always placed upside down the rounded side will be at the top of the disc only to prevent coins from jamming the mechanism Figure 8 Proper Finger Alignment Figure 8b Vend Figure 8a Accepted Accepted coins push the Coins should push the fingers out fingers over the Coin Make sure coins contact the Discs catches to vend center of the fingers in LOADING PRODUCT To present your product in as an attractive and professional manner as possible do not load any damaged items and make sure items are facing forward for easy identification by your customer Note The size of the item being vended must be larger than the Helix Coil but smaller than the Column to vend correctly Never force an over
Download Pdf Manuals
Related Search