COMBINATION SPEEDOMETER/TACHOMETER GAUGE KIT
Contents
1. cMOTOR HARLEY DAVIDSON GENERAL Ga INSTRUCTIONS COMBINATION SPEEDOMETER TACHOMETER GAUGE KIT REV 2013 02 05 is03400 U S Department of Transportation National Highway Traffic Safety Administration Title 49 United States Code Subtitle VI Motor Vehicle and Driver Programs Part C Information Standards and Requirements Chapter 327 Odometers Section 32703 Preventing tampering A person may not 1 advertise for sale sell use install or have installed a device that makes an odometer of a motor vehicle register a mileage different rom the mileage the vehicle was driven as registered by the odometer within the designed olerance of the manufacturer of the odometer 2 disconnect reset alter or have disconnected reset or altered an odometer of a motor vehicle intending to change the mileage registered by he odometer 3 with intent to defraud operate a motor vehicle on a street road or highway if the person knows hat the odometer of the vehicle is disconnected or not operating or 4 conspire to violate this section or section 32704 or 32705 of this title Section 32704 Service repair and replacement a Adjusting mileage A person may service repair or replace an odometer of a motor vehicle if the mileage registered by the odometer remains the same as before the service repair or replacement If the mileage cannot remain the same 1 the person shall2. shop towels on the fuel tank Lift the console from the fuel tank turn it upside down and lay it on the covering J05180 4 Unplug the 12 terminal connector 39B from the back of the speedometer press the external latches and use a rocking motion to separate the pin and socket halves 5 Remove the back clamp Gently pry the three latches upward to release the back clamp from the back of the speedometer 6 Lift the console and remove the old speedometer from the console Discard the old speedometer but retain the rubber gasket and back clamp for use with the new gauge NOTE Set the console securely on the protected top of the fuel tank and take care that it does not fall off during the following oper ations 7 Set the console securely on top of the fuel tank INSTALLATION AND FINAL CHECK NOTE Apply window cleaning fluid or mild soapy water to the speedometer gasket as needed to aid installation 1 Turn the console over facing upward 2 Place the speedometer gasket into position around the console speedometer bore 3 Fix the new gauge into the bore so that it fits snugly against the rubber gasket Rotate the gauge into approx imate visual alignment The back clamp will complete the alignment 4 Turn the console over face down 5 Install the back clamp Place the back clamp over the back of the gauge aligning the two slots with the console bosses Press the latches down until they lock into posi t
3. adjust the odometer to read zero and 2 the owner of the vehicle or agent of the owner shall attach a written notice to the left door frame of the vehicle specifying the mileage before the service repair or replacement and the date of the service repair or replacement b Removing or altering notice A person may not with intent to defraud remove or alter a notice attached to a motor vehicle as required by this section Section 32705 Disclosure requirements on transfer of motor vehicles a 1 Disclosure requirements Under regulations prescribed by the Secretary of Transportation that include the way in which information is disclosed and retained under this section a person transferring ownership of a motor vehicle shall give the transferee the following written disclosure A Disclosure of the cumulative mileage registered on the odometer B Disclosure that the actual mileage is unknown if the transferor knows that the odometer reading is different from the number of miles the vehicle has actually traveled 2 A person transferring ownership of a motor vehicle may not violate a regulation prescribed under this section or give a false statement to the transferee in making the disclosure required by such a regulation 3 A person acquiring a motor vehicle for resale may not accept a written disclosure under this section unless it is complete A This subsection shall apply to all transfers of motor vehi
4. art the motorcycle Test for proper turn signal brake light and tail light operation 11 Check the speedometer and tachometer for proper opera tion NOTES e Both the ECM and speedometer retain the odometer value If the soeedometer is replaced it will display the odometer value stored in the ECM The replacement speedometer will become locked to the ECM after 31 1 miles 50km have been accumulated The trip B odometer will display the countdown mileage Once the countdown reaches zero the speedometer is locked to the ECM If installed on another vehicle the odometer will display VIN ERR If the speedometer is removed from the vehicle before the countdown reaches zero it has not been locked to the ECM This mileage countdown allows for a road test to verify that speedometer replacement was the proper repair e During the 31 1 miles 50 km countdown period before the speedometer is locked to the ECM the security light flashes for up to 15 seconds when battery power is restored to the electrical system while the new gauge synchronizes to the ECM e Gear Indication display is a calculated gear position based on wheel and engine speed The gear position displayed may be momentarily inaccurate depending on rider clutch use characteristics and clutch wear This momentary false reading although unlikely can occur if the clutch is allowed to slip either due to excessive wear poorly adjusted clutch or if the operator rides the clu
5. cles unless otherwise exempted by the Secretary by regulation except in the case of transfers of new motor vehicles from a vehicle manufacturer jointly to a dealer anda person engaged in the business of renting or leasing vehicles for a period of 30 days or less B For purposes of subparagraph A the term new motor vehicle means any motor vehicle driven with no more than the limited use necessary in moving transporting or road testing such a vehicle prior to delivery from the vehicle manufacturer to a dealer but in no event shall the odometer reading of such vehicle exceed 300 miles 5 The Secretary may exempt such classes or categories of vehicles as the Secretary deems appropriate from these requirements Until such time as the Secretary amends or modifies the regulations set forth in 49 CFR 580 6 such regulations shall have full force and effect J05180 Many Harley Davidson Parts amp Accessories are made of plastics and metals which can be recycled Please dispose of materials responsibly Figure 1 Title 49 United States Code GENERAL CONTINUED Kit Numbers Table 1 Kit Numbers Kit Type Description Number 74777 11A Gauge Speedo Tach KMH _ Black 74776 11A Gauge Speedo Tach MPH Black 74775 11A Gauge Speedo Tach KMH 74774 11A Gauge Speedo Tach MPH 70900171A Gauge Speedo Tach MPH KMH Spun aluminum Spun aluminum Spun aluminum Servic
6. display is enabled 5 To disable gear indication press and hold both turn signals until OFF is flashing 6 Toggle over to the brightness menu by pressing the right turn signal where all of the bars and BRIGHT will be displayed 7 To dim the backlight press and hold both turn signals until dim and half of the bars are displayed 8 Toggle over to the color menu by pressing the right turn signal where ALL and COLOR will be displayed J05180 signals where the current color number will be displayed 10 For coarse adjustment press left turn signal to count down and right turn signal to count up incrementally 11 For fine adjustment press and hold left turn signal to count down and right turn signal to count up 12 Once desired color is selected press and hold both turn signals until SAVED is displayed 13 To change the color for the other four components dial speedometer pointer tachometer pointer and display Toggle over to the color menu by pressing the right turn signal and follow steps 7 through 10 14 Once desired setup and colors are finalized turn ignition switch to the ignition IGN position and verify settings gear indication will appear until vehicle is running Battery Reconnection and Initialization After the battery is reconnected or a new gauge is installed the gauge requires about a half tank of fuel to properly initialize fuel range miles to empty functionality During cons
7. e Manual Required IWIN NIN The rider s safety depends upon the correct installation of this kit Use the appropriate service manual procedures If the procedure is not within your capabilities or you do not have the correct tools have a Harley Davidson dealer perform the installation Improper installation of this kit could result in death or serious injury 00333a NOTE This instruction sheet refers to service manual information A service manual for this year model motorcycle is required for this installation and is available from a Harley Davidson dealer REMOVING THE OLD SPEEDOMETER 1 Apply power to the motorcycle and record the odometer reading AWARNING To prevent accidental vehicle start up which could cause death or serious injury disconnect battery cables negative cable first before proceeding 00307a AWARNING Disconnect negative battery cable first If positive cable should contact ground with negative cable con nected the resulting sparks can cause a battery explosion which could result in death or serious injury 00049a 2 Refer to the service manual and follow the instructions given to remove the seat and disconnect the battery cables negative cable first Retain all seat mounting hardware NOTE Cover the fuel tank with an H D Service Cover or clean shop towel to prevent scratching the finish 3 Remove the instrument console acorn nut Place an H D Service Cover or clean
8. ion 6 Carefully insert the connector into the back of the speedometer 20f5 1 Console 2 Connector location Figure 2 Speedometer Tachometer Harness Routing 7 Turn the console over and center it on the fuel tank Install the acorn nut and tighten to 80 100 in Ib 9 0 11 3 Nm 8 Apply a light coat of Harley Davidson electrical contact lubricant part number 99861 02 petroleum jelly or corro sion retardant material to the battery terminals Refer to the service manual and follow the instructions given to re attach the battery cables positive cable first WARNING Connect positive battery cable first If positive cable should contact ground with negative cable connected the resulting sparks can cause a battery explosion which could result in death or serious injury 00068a WARNING After installing seat pull upward on seat to be sure it is locked in position While riding a loose seat can shift causing loss of control which could result in death or serious injury 00070b 9 Refer to the service manual and follow instructions to install the seat J05180 WARNING Be sure headlamp tail and stop lamp and turn signals are operating properly before riding Poor visibility of rider to other motorists can result in death or serious injury 00478b 10 Turn the ignition key switch to IGN but do not st
9. o to set up mode Loose connection with gauge con nector or trip reset button Check for bent accessory pin 6 in gauge connector or check trip reset button operation Gear Indication Gear Indication does not operate Not turned on Use instruction sheet to turn on gear indication in set up mode Fuel Level Fuel Level does not Not turned on in set up mode Use instruction sheet to turn on fuel operate level in set up mode Color Changing Color will not save Color was not saved properly Use instruction sheet for proper saving procedure Note Please contact Technical Service with any installation or troubleshooting questions before filing a warranty claim J05180 5 of 5
10. tch e If gauge is installed on a motorcycle with ABS be sure the ABS warning lamp is working properly See the owner s manual for ABS warning lamp operation Backlight Color Modification The backlight color can be modified for the entire gauge or the dial speedometer pointer tachometer pointer and display separately see Table 2 The gear indication and fuel level display can also be disabled 1 Turn ignition switch to the accessory ACC position 3 of 5 Table 2 Color Guide Number Range Color 000 015 Red 016 030 Amber Orange 031 060 Yellow 061 100 Yellow Green 101 180 Green 181 250 Green Blue 251 350 Blue 351 380 Blue Violet 381 440 Violet 441 490 Pink 491 525 Red Figure 4 Select Display Color 526 600 White Light Colors Note Color descriptions and color ranges are approximate 9 See Figure 4 To change color press and hold both turn is07365 Figure 3 Fuel Level Display Setup 2 See Figure 3 Press and hold both turn signals until fuel level bars are displayed with ON OFF flashing SETUP will also appear If ON is flashing the fuel level display is enabled 3 To disable fuel level press and hold both turn signals until OFF is flashing 4 Toggle over to gear indication by pressing the right turn signal where the six gears will be displayed with ON OFF flashing If ON is flashing the gear indication
11. umption of the first full tank of fuel the gauge software will begin the process of learning your riding patterns eventually tailoring the fuel range calculations to your unique riding characteristics The fuel level display and tank mounted fuel gauge may not match at all times when starting with a full tank of fuel The tank fuel gauge utilizes a continuous sweep needle to indicate fuel level while the speedo tach fuel level utilizes a segmented display Each segment represents 1 8 of a tank For example if a given segment just came on or is about to go off it would show no change while the needle on the tank mounted gauge would likely show a change in position Fuel Fill up and Top off When adding fuel to the vehicle it is recommended you add at least two gallons 7 6 L of fuel to update the fuel and range displays If the fuel display does not update immediately after the vehicle is put in motion the fuel and range displays will slowly update over the next 30 miles 48 3 kilometers Press and hold the Trip reset switch to toggle between the mile and kilo displays 40f5 TROUBLESHOOTING Table 3 Troubleshooting Operation Problem Possible Cause Possible Solution Installation into vehicle harness LCD states vin err Gauge was already married accu mulated 31 1 miles 50 km to another vehicle Reinstall on previous vehicle to confirm no vin err Entering set up mode Will not g
Download Pdf Manuals
Related Search