Coffee Maker Senseo HD7810/55 /C - Expert-CM
Contents
1. Corrugated tube hose Foot 5 52. has finished it is stabilized to perform the volume adjustment 6 Empty the cup and push again for one cup setting measure the volume output with a graduated beaker In the table you can find the requirements for the minimum maximum volume output cc mL values depending from the country version One cup setting Including Pod holder water spec Without Coffee pod Lo Min water cc mL Max water cc mL Unplug the appliance from the mains Press the 1 and 2 cup button simultaneously and plug the mains on 9 When above step succeeded the LED will turn on continuously 10 Depending if the volume has to de or increase you have to push the 1 or 2 cup button Every time you push the 1 or 2 cup button the LED will turn off for 0 5 second feedback to user and the pump time will be shorten or lengthen for 0 5 seconds depending which button was pushed Pushing 1 cup button pump time will be shorten with 0 5 sec is approximately 3 5 cc mL less coffee Pushing 2 cup button pump time will be lengthen with 0 5 sec is approximately 3 5 cc mL more coffee HD7810 55 C When the volume has to increase with 10 cc for example push the 2 cup button 3 times The new value will be stored when you switch the appliance off by pushing the main switch LED will turn off 11 Turn appliance on again and brew one cup measure the volume In case the volume is not within specification repeat steps 6 11 12 End Aut
3. Coffee Maker Senseo Service HD7810 55 m TA IC SEVICE Service Philips Domestic Appliances and Personal Care ervice Manua PRODUCT INFORMATION TECHNICAL INFORMATION This product meets the requirements regarding Voltage 220 230 V interference suppression on radio and TV Frequency 60 Hz After the product has been repaired it should function Power consumption 1450 W properly and has to meet the safety requirements as oe er ere rn officially laid down at this moment Y P P ae Contents reservoir 7 9 Ce Colour setting White Sunset orange SAP coding HD7810 55 C Waterlevel Temp Sensor Sensor Pump M CONTROL PCB Push buttons Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands Copyright reserved Subject to modification 07 05 PHILIPS DISASSEMBLY AND RE ASSEMBLY ADVISE Disassembly information To remove the brew chamber lid cover handle as follows Place the screwdriver on the positions see picture 1 and lift the cover over the snap locks on both positions The cover lid can now be lifted up a little and to remove the complete cover including lever and push rod squeeze strongly with two fingers both legs of the push rod see picture 2 to each other so that the two pins will get out of the hinge position on the brew chamber To remove lever from lid cover take a screwdriver and bend carefully the two lips ribs in the lid c
4. n status has the benefit the flush routine will be activated automatically when installed by the consumer see topic Automatic filling procedure To SET the Boiler_empty_flag can be done by Keep the 1 cup button pressed while plugging in the power cord of the appliance To check if the Boiler_empty_flag is really set you should reconnect the power cord a second time to the net do not push any buttons The LED should blink very fast for 0 5 seconds at the moment the power cord was connected to the net 3 5 PARTS LIST amp EXPLODED VIEW HD7810 55 C y Nn Service code Description 4222 259 40410 Pad holder single Corn silk yellow 4222 259 40420 Pad holder double Corn silk yellow 4222 247 52980 Foam chamber cover Corn silk yellow 4222 247 39540 Foam chamber 4222 240 06670 Drip tray cover 4222 247 35790 Drip tray 4222 247 06810 Brew chamber radial seal 4222 259 06890 Distrubutor assy CON AY BK OW NH 4 5 PARTS LIST amp EXPLODED VIEW 11 Service code 4222 259 34970 4222 259 40400 4222 259 20100 4222 247 52950 Description Valve 3way Water tank assy Sun flower orange XL 10 Cups Water tank assy Silent blue Valve outlet Bright white HD7810 55 C Service code 4222 247 35870 4222 247 05180 4222 247 39890 4222 247 05110 4213 247 05250 Description Filter WC Sealing WC socket Hard
5. omatic filling procedure The Senseo PCB contains an automatic filling procedure software routine This fill routine is only meant for back up Normally the consumer has to follow the guidelines stated in the DFU The filling procedure functions as follows The consumer has to fill the water container and has to plug the appliance on the mains When the Senseo main switch has been pushed the main switch LED will light continuously This is only the case when the Senseo has not finished the filling procedure completely First use When the consumer pushes the one or two cup button the Senseo will start automatically the pump to fill the boiler When the boiler is filled the pump stops pumping Pump time approximately 20 seconds When the filling procedure has been successful the software will clear a Boiler_empty_flag in the Eeprom By means of this Boiler_empty_flag the system knows the boiler is filled or not When the Senseo is switched off or disconnected from the mains the value of the Boiler_empty_flag is stored in the Eeprom chip Restoring the Boiler_empty_flag to production default Some times it is needed that the boiler of the Senseo have to be emptied This for instance in wintertime were the possibility exists that the boiler becomes frozen during transport e g For those occasions it is handy to restore the Boiler_empty_ flag again to production default in the Eeprom Bringing the Senseo back into productio
6. ove the rest of the housing unlock the last 4 snap locks at the base and gently pull of the front cover To reassemble follow above steps backwards OPTIONAL accessories XL watertank 10 Cups Commercial type number HD7982 Service code 4222 259 20100 2 5 REPAIR INSTRUCTION Descaling Regular descaling will prolong the life of your appliance and will guarantee optimal brewing results for a long time Follow the steps in the section headed Preparing the appliance for use see DFU Direction for Use manual Instead of only water use a mix of water and Lemon sour For the best result leave the mix of water and Lemon sour for about 30 minutes in the appliance before you start with flushing the appliance To get the best results repeat above mentioned step once or twice When finished flush the appliance twice by repeating the above mentioned steps only use water instead Volume adjustment The new PCB circuit board makes it possible to adjust the volume output by means of pushing the one cup and two cup user controls How to adjust the volume output 1 Be sure the boiler is filled properly other wise perform fill procedure see DFU for instructions 2 Switch appliance on and wait until the unit is ready to brew 3 Be sure a pod holder is placed but without a Coffee POD Only adjusting with plain water 4 Place a cup on the drip tray cover and push the one cup button 5 When the appliance
7. over outwards and push the lever with force out of the hinge Reassemble follow steps backwards without using a screwdriver To remove the back cover handle as follows Remove valve outlet Start at the upper side of the back cover and stick a screwdriver into the 2 snap locks positions and gently pull the back cover from the appliance so that a little chink between back cover and brew chamber becomes visible Put the screwdriver in to the 4 rectangular holes snap locks at the back and gently pull the screwdriver such away that the lips of the snap locks are bent outwards If all clicks positions are loose it is possible to remove the back cover Reassemble follow steps backwards HD7810 55 C Removing Brew chamber head handle as follows Disassemble back cover Place the appliance such a way that you are looking at the boiler First remove the boiler from the snap lock position of the brew chamber To remove the brew chamber use your both thumbs see picture 3 and push strongly with a little distortion rotation until the brew chamber comes loose Reassemble follow above steps backwards picture 3 To reach the components placed on the base handle as follows First remove back cover brew chamber and 3 way valve Remove both Torx T15 screws see exploded view in the near of position A Bend the 2 click snap locks with a screwdriver see base and the housing can now be removed To rem
Download Pdf Manuals
Related Search