SB9015D_ service manual 20120327
Contents
1. 1 10 6 LCD Panel 1 nennen 11 T Contents oO bematech 1 Before You Start 1 Please unplug the power cable before you start to work 2 Please read and follow the instructions in this document carefully Failure to follow these instructions could damage your device and void the warranty 1 1 Tools Suggested All procedures in this document require the following tools SH q 0 Phillips screwdriver 1 Phillips screwdriver Magnetized suggested Magnetized suggested OE 1 5 mm hexagon socket spanner Magnetized suggested e bematech 2 Opening the Device 1 Loosen the screw as shown 2 Separate the device from the base NR 3 Un tighten the four screws on the back panel anticlockwise X bematech 4 Separate the back panel from the front panel by lifting up and lay it down carefully e bematech 3 Mainboard side Components Replacement Mainboard Layout For relative location of onboard connectors please refer to the pictures below 18 CON1 LED CON1 CRT1 SATAHDD2 LVDS24 CON1 LVDS 18 SATAHDD1 LINEOUT CON1 c A N gt lt fl dd FW CON1 2 24VOUT_CON1 bematech 1 Open the two ejectors on the slot by pushing them and remove the RA2. M from the slot Align and insert the new RAM into the slot and push both ends of the RAM down until the ejectors snap into place 3 Disconnect the SATA cable from the SATA HDD1 connector of the main board SATAHDD1 ur 4 Disconnect 1 VGA cable 2 LVDS LCD cable 3 inverter cable 4 led CABLE 5 speaker cable and 6 power switch cable from the mainboard Chapter 3 bematech 5 Disconnect 1 Parallel port cable and 2 Touch panel cable 6 Loosen the two screws by 1 5 mm hexagon socket spanner as shown below bematech 8 Remove the mainboard 9 Loosen the four screws by 1 5 mm hexagon socket spanner as shown below and then you can remove the VGA port cable and the parallel port cable 10 Loosen the two screws as shown and remove the IO bracket Chapter 3 7 bematech 11 Remove the power switch bematech 4 HDD Replacement 1 Loosen the four screws by 1 Phillips screwdriver and Unplug the SATA cable and power cable from the HDD then you can remove the HDD assembly 2 Loosen the four screws fixing the HDD on the both side and then you can remove the HDD e 3 Install the new HDD in the reverse procedure from Step 4 to Step 1 e bematech LCD Inverter Replacement 1 Disconnect three connecters shown below 2 Disconnect three connecters and three screws from LCD
3. inverter as shown below and then you can remove the LCD inverter m y gt u n ZEE ER E ME MEE c Fra JO P m T 3 Install the new LCD inverter in the reverse procedure 10 oO bematech LCD Panel Replacement 1 Unplug the LED indicator 2 Disconnect the touch panel cable A 0 3 Loosen the two screws and remove the led indicator len 11 bematech 5 Loosen the six screws as shown and remove the LCD assembly from the front bezel 6 Loosen the four screws as shown and then you can remove the LCD from the LCD chassis 12
4. oO bematech Service Manual SB 9015D bematech Copyrights 2010 Logic Controls Technology Corp All rights reserved The information in this document is subject to change without prior notice in order to improve reliability design and function and does not represent a commitment on the part of the manufacturer This document contains proprietary information protected by copyright All rights are reserved No part of this manual may be reproduced by any mechanical electronic or other means in any form without prior written permission of the manufacturer All trademarks are property of their respective Owners Liability Disclaimer In no event will the manufacturer be liable for direct indirect special incidental or consequential damages arising out of the use or inability to use the product or documentation even if advised of the possibility of such damages The information in this document is subject to change without notice 9 bematech Contents AA nun nun nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn j E E T REDDE m li 1 Before You Start acorta 1 2 Opening the 2 Mainboard side Components Replacement 4 3 MANDO ANCL Layout ecc ee 4 4 HDD 9 5 LCD Inverter
Download Pdf Manuals
Related Search