Skidoo1200 Slip-On Full System
Contents
1. of muffler strap Then fasten muffler strap to bracket by using 8x20mm bolt supplied two 8mm washers supplied and an 8mm locknut supplied See Image 3 for reference Install second muf fler strap so that both ends of strap join to gether on the left side of the Hindle muffler Step 6 You must ground battery wire to 6mm hole on bent bracket Use 6mm bolt and 6mm locknut supplied to secure ground wire to muf fler bracket Failure to do so will result in snow mobile not starting See Image 4 for reference To install the HINDLE SKIDOO ROTAX 4 TEC 1200 full system proceed with the following directions Step 1 Remove the stock exhaust system as per owner s manual Caution do not install exhaust while snow mobile is running and or is hot to the touch Thoroughly read and review all steps of installation instruc tions to ensure proper installation Step 2 Install exhaust flanges into engine ports Tighten exhaust flanges to engine ports using stock studs Tighten finger tight Do not over tighten Step 3 Install Hindle front exhaust primaries into flanges Use spring puller tool provided to attach one spring on each primary to flange location Do not use pliers to install springs Failure to use spring puller tool pro vided may result in springs becoming over extended loosened Step 4 Install Hindle collector onto Hindle primaries using three 3 springs provided on each spring tab lo cation Use spring pulle2. r tool provided to attach springs Do not use pliers to install springs Failure to use spring puller tool provided may result in springs becoming over extended loosened Step 5 Insert Hindle muffler into Hindle mid pipe Attach two Hindle springs supplied from the Hindle muffler spring tab locations to the Hindle mid pipe spring tab locations Refer to Image 1 of Slip on instructions for reference Step 6 Install Hindle mid pipe and Hindle muffler assembly onto Hindle collector using two springs provided on each spring tab location Use spring puller tool provided to attach one springs Do not use pliers to install springs Failure to use spring puller tool provided may result in springs becoming over extended loosened Step 7 Follow Step 4 Step 5 and Step 6 of Skidoo 1200 Rotax 4 Tec Hindle Slip on instructions to install Hindle muffler A WARNING xhaust system s and muffler s may be hot when engine is has been running Take preventative measures ith the handling of any Hindle system or Hindle muffler Allow the engine to cool before installing or re oving the exhaust system and or muffler Severe burns bodily injury and or death may occur WARNING eep flammable materials away from exhaust at all times A WARNING xhaust gas contains poisonous carbon monoxide that can rapidly accumulate in an enclosed or poorly entilated area If inhaled it may cause serious injury or death Start and run the motorcycle in a well en
3. r tool provided to attach springs Do not use pliers as this will dam age the springs See Image 1 for reference Step 3 Install Hindle muffler and Hindle slip on adapter mid pipe assembly onto stock col lector Ensure that muffler exhaust tip is lined up with stock rear exhaust hole Use two stock springs not included with Hindle system or use Hindle springs included to secure Hindle slip on adapter mid pipe to stock front section Use spring puller tool provided to attach springs Do not use pliers as this will dam age the springs See Image 2 for reference Step 4 Remove protective plastic wrap from outer side of muffler strap Install muffler strap protective rubber insert on inside of muf fler strap Ensure that grooves of rubber insert form around edge of muffler strap Install first muffler strap so that both ends of strap meet behind the Hindle muffler Use T shape bracket supplied to mount muffler strap to stock muffler rubber mount on upper frame Use 8x20mm bolt supplied two 8mm wash ers supplied and one 8mm locknut sup plied to secure muffler strap to bracket Step 5 Use bent bracket supplied to mount muffler strap to tunnel on frame Use stock bolts not supplied to mount bracket to frame Remove protective plastic wrap from outer side of muffler strap Install muf fler strap protective rubber insert on inside of muffler strap Ensure that grooves of rub ber insert form around edge
4. s mail the product prepaid and a copy of your dated sales receipt as proof of purchase together with a note explaining the reason for repair to this item to Hindle Products Ltd 140 North Port Road Port Perry Ontario Canada L9L 1B2 Product being returned without notification prior to shipping will be overlooked Upon receipt Hindle Products Ltd will repair or replace as appropriate your Hindle product and return it to you post paid Warranty is solely through Hindle Products Ltd Service to our products by anyone other than Hindle Products Ltd voids warranty Hindle Products Ltd disclaims any and all liability for consequential or incidental damages Hindle Products Ltd will not be held responsible for personal damage bodily harm or any other legal matters
5. tilated area 12 MONTH LIMITED WARRANTY AND LIABILITY DISCLAIMER Hindle Products Ltd warrants this product free from defects in material or workmanship for a period of 12 months from the date of purchase except as noted The prod uct warranty does not cover damage caused by misuse or abuse accident the attachment of any unauthorized accessory alteration to the product improper installation exposure to harsh weather and or chemicals lack of proper maintenance or any other conditions that are beyond the control of Hindle Products Ltd Hindle Products Ltd shall not be responsible for any type of incidental consequential or special damages All implied warranties including but not limited to those warranties of fitness and merchantability are limited in the total duration to 12 months from the original purchase date Hindle will not warrant any product for fitment issues after the system has been ran on the motorcycle for any length of time If the warranty occurs within 30 days from the date of purchase please contact the dealer product was purchased from Over 30 days from the date of purchase please contact Hindle Products Ltd direct at 905 985 6111 before shipping the product Customer must contact Hindle Products Ltd prior to sending warranty product Claims for lost shipment damaged shipments or other problems regarding freight must be made directly to the responsible carrier To obtain warranty service on Hindle Exhaust System product
6. x ah eit ete ut i ft ppe oe wi i z i se z a _ E P Py r s HINDLE PRODUCTS LTD RN a ON A aari y4 140 North Port Road e _ Heel a Port Perry Ontario a L9L 1B2 CANADA Tel 905 985 6111 Fax 905 985 7349 General Mounting Instructions for SKIDOO ROTAX 4 TEC 1200 SLIP ON Pages 1 2 and FULL SYSTEM Pages 2 3 b ae 7 i Thank you for investing in a Hindle Exhaust System Performance quality and sound is what we re all about Below you will find instructions to mount a Hindle Exhaust Slip on Pages 1 2 or Full System Pages 2 3 for a SKIDOO ROTAX 4 TEC 1200 Should you have any questions about installation please do not hesitate to contact us and we would be happy to help out LEVEL OF DIFFICULTY DIFFICULT TIME REQUIRED 1 1 5 HOURS FOR SLIP ON 3 HOURS FOR FULL SYSTEM TOOLS NEEDED To install the HINDLE SKIDOO ROTAX 4 TEC 1200 slip on proceed with the following directions Step 1 Remove the stock muffler and stock elbow mid pipe as per owner s manual Caution do not install ex haust while snowmobile is running and or is hot to the touch Thoroughly read and review all steps of installation in structions to ensure proper installation Step 2 Insert Hindle muffler into Hindle slip on adapter mid pipe Attach two Hin dle springs supplied from the Hindle muf fler spring tab locations to the Hindle slip on adapter mid pipe spring tab locations Use spring pulle
Download Pdf Manuals
Related Search