Home

nba-hoop-troops-kids..

1. Figure 2 Figure 3 11 For More Product Information On This 1600 Other Arcade and Amusment Products Visit www BMIGaming com Display Panel Removal The control panel has two different displays boards One display shows the high score while the other has both the current score and credits remaining To replace either displays remove the three mounting screws shown to the left and remove the mounting bracket Now lift the display panel assembly up and out Disconnect the wire harness Each display is attached to the display panel with four plastic standoffs Remove the stand offs on the display you wish to replace Assembly in reverse order 4 60642 CB2232X PC60628 03105 2233 PartNo Description For More Product Information On This 1600 Other Arcade Amusment Products Visit www BMIGaming com QUICK TROUBLESHOOTING PROBLEM BALL GATE WILL NOT OPEN OR CLOSE OR MOVES VERY SLOW PUSHBUTTONS DO NOT LIGHT OR WORK PROPERLY BALLS DO NOT SCORE CORRECTLY GAME DOES NOT TAKE OR ADD MONEY CORRECTLY GAME DOES NOT DISPENSE TICKETS CORRECTLY NO OR LOW GAME SOUND BALLS DO NOT DISPENSE QUICKLY ENOUGH OR JAM IN THE GAME DISPLAY LED S DO NOT WORK PROPERLY BAD OR LOW 12 TO MOTOR BAD WIRING TO BALLGATE BAD MAIN PC BOARD BAD BALL GATE BOARD BAD BULB IN BUTTON BAD MICROSWITCH IN BUTTON BAD WIRING TO MAIN PC BOARD BAD MAIN PC BOARD BUTTON STUCK SHUT BA
2. See adjusting sensor for proper operation If the net is not tied back away from the sensor it can block the sensor When the sensor is no longer blocked the error will clear 6 Coin 1 Stuck Down Self Clearing This error occurs when the coin switch is con nected to the normally open position or held closed The error will clear when corrected 7 Coin 2 Stuck Down Self Clearing See error 6 8 DBV Stuck Down Self Clearing See error 7 9 Start button stuck Self Clearing This error will occur either if the start button is wired to normally closed or the button is stuck on Fixing this will clear the error 10 Ignore Not used Self Clearing Self clearing errors can correct themselves without a reboot all others will require a reboot This can be accomplished by entering and then exiting program ming or a physical power cycle Compact flash error only indicates that the CF is not detected The CF access light on the brain board will appear to be on solid if there was an error on power up Should you not get audio but the access light is not on solid then either the card data is bad or the card was put in with power on and cycled the game by entering and exiting programming Possi ble conditions are CF error code and CF access Light solid either bad wrong no card or card inserted with power on the game CF error code and CF Light blinks should not oc cur but this would indicate that the card has go
3. THEY CAN BE VERY SUS CEPTIBLE TO DAMAGE FROM SHORT CIRCUITING OR PHYSICAL ABUSE ALWAYS UNPLUG THE GAME WHEN WORKING ON HIGH VOLTAGE AREAS OF THE GAME SUCH AS THE TRANSFORMER USE EXTREME CAUTION WHEN USING VOLTME TERS TO DO CIRCUIT CHECKS IF THE GAME POWER HAS BEEN LEFT ON WHEN USING A VOLTMETER BE SURE IS SET TO THE CORRECT VOLTAGE OR RESISTANCE RANGE BEFORE USING THIS CAN PREVENT POSSIBLE DAMAGE TO THE PC BOARD OR MISDIAGNOSIS ALWAYS REMOVE POWER TO THE GAME WHEN PLUGGING OR UNPLUGGING PC BOARDS IT IS NECESSARY TO USE ONLY ICE REPLACEMENT PARTS TO CONTINUE WARRANTY COVERAGE USE OF NON ICE APPROVED PARTS WILL NOT ONLY VOID YOUR WARRANTY BUT COULD CAUSE SERI OUS HARM TO THE GAME OR CAUSE SERIOUS BODILY INJURY IF YOU HAVE ANY QUESTIONS REGARDING REPAIR PARTS OR OPERATION PLEASE CALL OUR SERVICE DEPARTMENT AT SERVICE DEPARTMENT 716 759 0360 NORMAL BUSINESS HOURS ARE MONDAY FRIDAY 9 00 AM TO 6 00 PM EST 10 FUSES Normally fuses are the first items that should be checked when the game is inoperable or works incorrectly There is only 1 fuse in the game and tt is resettable It is located on the backside of the front podium by the AC input cord HOOP SENSOR It might be necessary to adjust the score sensor of your game depending on your lighting conditions of your loca tion Located at the top of the sensor is a small adjust ment screw that adjusts the sensitivity of the sensor and a
4. you are in programming mode and not game mode 1 To advance through the different modes press the SEL button located next to the PROG but ton Each push of the button will advance you to the next mode The modes are displayed on the Score display Whenever you are done with any programming changes push the PROG button to return to normal game play 2 he current value for each mode will be shown in the High Score display To change the shown value to the next number press the ADV button next to the SEL button in the coin door MODE 0 VOLUME This option is used to change the relative sound vol ume of the game 0 is the lowest the game can be set to play at while 8 is the loudest Each time the button is pushed a sound is played to make it easier to determine where the volume level should be set The factory default for this option mode is 3 MODE 1 COINS PER CREDIT COIN INPUT 1 This mode determines how many coins are needed to create 1 credit for coin input 1 This is also the only coin input normally adjusted for most usage This value can be adjusted from 0 10 Setting a 1 would indicate 1 coin is needed to obtain 1 credit A 2 would indicate 2 coins are needed to obtain 1 credit Setting a 0 sets the game to the FREE PLAY mode The factory default for this setting is 2 MODE 2 COINS PER CREDIT COIN INPUTS 2 This adjusts how many coins are required to r
5. DISSASSEMBLY To remove the hoop you will need to remove the front panel It is attached to the back board with 7 mounting bolts and washers w Remove these Now you can access the four mounting bolts and washers that hold the hoop Assembly in reverse m BACK BOARD DISPLAY ASSEMBLY To access the back display remove the back access panel as shown For More Product Information On This 1600 Other Arcade and Amusment Products Visit www BMIGaming com 559 0199 Id SOHS 2 1 X 01 60909244 TIVE 2201 CW ONIHV38 31V9 1Y 00EdH 91 6 LAVHS 31VO 11 8 cOLdH YOLOW SLVD 11 800048 1 DNILNNOW HOLOW 31VO Tivd 0L88 MOVIE SAING OS v EX84 569 wonduoseq oNued 800244 0909244 cCOLGIN cOLdH 00 dH 15 For More Product Information On This 1600 Other Arcade and Amusment Products Visit www BMIGaming com PARTS LISTINGS MECHANICAL PARTS BB3008 MD3017 201 HP3001 HP3019 MD1050 P100 MD1139 P200 MS1013 P802 3028 3030 5014 5101X BB1009 BB1023 BB5001 BG3002 HG1008 P802 1024 1026 HP1009 HP1023 MD1009 p802 MD1013 p802 Net Re bounce guard Chrome T Molding Basket Ball 5 rubber Ball Inflation gauge Top cage Hoop Side cage Screw cap royal blue Screw cap black Lock 45 Mech holder assembly Cash box enclosure Bracket for Ball gate motor Cash Box
6. Speaker Grill Cash box door black Ticket Bin Low ticket switch bracket Ball gate motor cover Ball gate shaft Coin door Ticket door ELECTRICAL amp ELECTRONIC E00210MDJX CB2233X CB2232X 2007 E00418AMDX E00418BMDX E00418CMDX E2034X HH5005CL HP2005 MD2008X MD3106 MD3107 MD3108 NB2032X NB2234X WA2010CB 2289X E0021 1 Net Sensor Display Display 4 round Speaker 51 LED white tape strip 75 LED white tape strip 51 LED white tape strip PCBA Brain board Ticket Dispenser Orange start button ASY Gate Motor LED Frosted Strip Upper left LED Frosted Strip Upper right LED Frosted Strip Lower Display Main I O Power supply Reset Button assembly Ticket low switch GRAPHICS amp DECALS MD3137 MD3138 MD3102 MD3105 MD7102 MD3102P MD7101 MD7103 MD7104 MD7105 MD7106 MD7107 7011 MD2152MX MD2153MX MD2155LX MD2160LX MD2170LX MD2171LX MD2180MX MD2181LX MD2183LX NB2253X 16 High Score Red Filter ocore Credits Red Filter Backboard Display Panel Decal Display Panel Reflector Decal Back Board white lines Cabinet Top Decal Rear Cabinet sides Front Cabinet sides Backboard Logo Ticket Door decal Cash Door logo logo front HARNESSES Coin door harness Ticket door harness Programming harness Main DC power harness Hoop ground extension harness Hoop ground harness Backboard Ball gate harness Display control panel harness Speaker harness Display harne
7. operation indicator The sensor is mounted sideways onto the hoop The ad justment screw and indicators are located on the right side of the game When the sensor is properly working the Green LED will be constantly on to indicate the sensor is operating When the sensor detects a object in front it will briefly light the orange LED If the object continues to block the sensor the orange LED will remain on until the object is removed To adjust the sensor turn the adjustment screw clockwise towards its maximum position Now turn the adjustment screw counter clockwise until the green LED turns off Go slow Now turn the adjustment screw halfway between this point and maximum sensitivity Indicator Adjustment screw For More Product Information On This 1600 Other Arcade and Amusment Products Visit www BMIGaming com ACCESS TO MAIN BOARD AND POWER ADJUSTMENTS To gain access to the main circuit board adjust the power supply or replace the power supply you will need to remove the four mounting bolts that hold the podium floor See Figure 1 Now remove the floor piece See figure 2 The main board is located on a small shelf and held down with plastic standoffs Remove the standoffs to remove main board The power supply is located at the bottom of the cabinet There you will also find a small knob or pot that has a arrow to indicate which way to turn to increase power Use a volt meter to confirm the 12 volt output Figure 1
8. 200 the default setting for this mode is 20 MODE 12 BONUS SCORE This mode allows you to select the number of tickets or a free game for a player reaching the Bonus Score The settings for this mode can be adjusted from 0 to 200 tick ets The default setting for this mode is 100 MODE 13 FACTORY DEFAULTS When this mode is selected the game will revert to all factory default settings ERROR CODES If any error occurs then a single dot will appear in the far right location of the credit display To see what that error is you press the advance button when not in accounting To exit this display just press advance again It should be noted that this will work even during a game When you are in this dis play the letters Er will show up in the credits display These are the errors For More Product Information On This 1600 Other Arcade and Amusment Products Visit www BMIGaming com CUSTOMIZING YOUR GAME 1 Ticket Error Self Clearing This error will occur when either a ticket jam occurs or there are no tickets available to dispense This error will clear when it sees the ticket notch line change state 2 Compact Flash Error This error will occur when the compact flash card cannot be accessed Game sounds and music will be missing Replace with a good flash card with the power off to clear this error 5 Hoop Blocked Self Clearing This error occurs when the sensor is blocked or has become defective
9. D SENSOR SENSOR DIRTY REFLECTIVE STRIP DIRTY BAD HARNESSING OR WIRING BAD MAIN PC BOARD BAD MAIN PC BOARD BAD MICROSWITCH OR DBV BAD WIRING TO MICROSWITCH OR DBV GAME PROGRAMMING SET WRONG BAD TICKET DISPENSER BAD WIRING TO DISPENSER OUT OF TICKETS TICKET SENSOR IS DIRTY DISPENSER JAMMED GAME PROGRAMMING SET WRONG BAD MAIN PC BOARD VOLUME TURNED DOWN BAD SPEAKER BAD WIRING TO MAIN PC BOARD BAD MAIN PC BOARD BAD MAIN PC BOARD BAD POWER PROBABLE CAUSE SOLUTION CHECK POWER SUPPLY ADJUST CHECK WITH VOLTMETER REPAIR OR REPLACE PC BOARD REPLACE ACTUATOR CHANGE LIGHT BULB REPLACE MICROSWITCH CHECK WITH VOLTMETER REPLACR MAIN PC BOARD REMOVE AND CLEAN BUTTON REPLACE SENSOR CLEAN USE NO SOLVENTS CLEAN USE NO SOLVENTS CHECK WITH VOLTMETER REPLACE MAIN PC BOARD REPLACE MAIN PC BOARD REPLACE SWITCH OR DBV CHECK WITH VOLTMETER RESET GAME PROGRAMMING REPLACE TICKET DISPENSER CHECK WITH VOLTMETER ADD TICKETS CLEAN SENSOR ON DISPENSER REMOVE TICKET JAM RESET PROGRAMMING REPLACE MAIN PC BOARD TURN UP VOLUME REPLACE SPEAKER CHECK WITH VOLTMETER REPLACE MAIN PC BOARD GAME HAS EITHER TOO MANY OR TOO FEW GAME IS DESIGNED TO WORK BALLS WITH 7 BALLS REPLACE PC BOARD CHECK POWER OUTPUT GAME WILL NOT RETAIN BAD MAIN PC BOARD REPLACE PC BOARD CUSTOM PROGRAM SETTINGS 13 For More Product Information On This 1600 Other Arcade and Amusment Products Visit www BMIGaming com BACK BOARD
10. For More Product Information On This 1600 Other Arcade and Amusment Products Visit www BMIGaming com NBA Jr Basket Ball 44S 4 SS SS 383 3 S 773 BSAA 74 ERR NWN OBESSSSNSSNNNNNNNN fis A 7024741 SC DEOR OWNERS AND SERVICE MANUAL INNOVATIVE CONCEPTS IN ENTERTAINMENT INC For More Product Information On This 1600 Other Arcade and Amusment Products Visit www BMIGaming com TABLE OF CONTENTS PRO SEED eoe PAGE 3 e SAFETY PRECAUTIONS e GAME SET UP e DISASSEMBLY CUSTOMIZING YOUR PAGE 7 e ENTERING SET UP MODE e CHANGING GAME SETTINGS e PROGRAMMING MODES e ERROR CODES MAINTENANCE amp TROUBLESHOOTING PAGE 10 e OPERATIONAL BACKGROUND e MECHANICAL REPAIR e MECHANICAL MAINTENANCE e ELECTRONIC amp ELECTRICAL REPAIR e FUSES e HOOP SENSOR e MAIN BOARD amp POWER SUPPLY e DISPLAY PANEL REMOVAL QUICK TROUBLESHOOTING PAGE 12 Aone MBEE n PAGE 14 e BALL GATE ASSEMBLY PARTO EO MING ER 16 17 REVISION B 4 8 2011 For More Product Information On This 1600 Other Arcade Amusment Products Visit www BMIGaming com BEFORE YOU BEGIN WARNING WHEN INSTALLING THIS GAME PRONG GROUNDED A C RECEPTACLE MUST BE USED FAILURE TO DO
11. SO COULD RESULT IN INJURY TO YOURSELF OR OTHERS FAILURE TO USE A GROUNDED RECEPTACLE COULD ALSO CAUSE IMPROPER GAME OPERATION OR DAMAGE TO THE ELECTRONICS DO NOT DEFEAT OR REMOVE THE GROUNDING PRONG ON THE POWER CORD FOR THE SAME REASON AS GIVEN ABOVE USING AN IMPROPERLY GROUNDED GAME COULD VOID YOUR WARRANTY HAVE A QUALIFIED ELECTRICIAN CHECK YOUR A C RECEPTACLE TO BE SURE THE GROUND IS FUNCTION ING PROPERLY SET UP The game is fully assembled and requires no further assembly Although the game is shipped with our suggested set tings as its default we still suggested that you read through Customizing Your Game to fully understand all options available to you in setting your game for your location DISASSEMBLY The game can be dissembled if necessary to accommodate small door ways You will need to remove rebound guard first Then remove the cages starting with the top and then the sides The back board then can be removed The up per mounting bolts on the backboard must be removed in order for the cages to come out The front podium can be re moved once the supporting bars are removed Refer to the diagrams in the next few pages for how each of the compo nents are attached to each other The game can now be brought in and reassembled Bp MY For More Product Information On This 1600 Other Arcade and Amusment Products Visit www BMIGaming com MD1050 Description 6032 8 x 50 Hex Head S
12. eceive 1 credit on the game s RIGHT HAND COIN MECHA NISM This mechanism is set differently so it can be used for fractional credits For normal use set a 1 for this mode If you wish to use this for coins with a different value than that of coin mech 1 contact our service department for set up information for your particular application The factory default for this set ting is 41 MODE 3 CREDITS PER DOLLAR BILL This option controls how many credits you will re ceive for each dollar bill inserted This value can be adjusted from 0 10 The factory default for this set ting is 4 For More Product Information On This 1600 Other Arcade and Amusment Products Visit www BMIGaming com CUSTOMIZING YOUR GAME MODE 4 COIN DISCOUNTING This option is used to create Bonus Credits The way this option works is as follows if a 3 is set for every 3 coins put in AT THE SAME TIME 1 extra credit would be given The range for this option is 0 10 Setting a 0 turns this option off The default value for this option is O MODE 5 TIME PER CREDIT This adjusts in seconds how long each game will last The game can be adjusted from 20 to 60 sec onds The recommended time is 40 seconds MODE 6 JUST FOR PLAYING TICKETS This feature is valuable in 2 respects 1 This can be set from 0 to 10 tickets So that if a player especially a young child who can not get the minimum points req
13. elf Drilling Screw MD1011 MESH FRAME MD1050 MESH FRAME For More Product Information On This 1600 Other Arcade Amusment Products Visit www BMIGaming com For More Product Information On This 1600 Other Arcade and Amusment Products Visit www BMIGaming com Using a latch tool from the sides of the cabinet unlatch each side MD1014 P802 No 6075 1 4 x 3 4 FLAT WASHER ZINC USS 6202 14 20x1 34 LG HHMB MD1014 P802 For More Product Information On This 1600 Other Arcade Amusment Products Visit www BMIGaming com CUSTOMIZING YOUR GAME CUSTOMIZING YOUR GAME This section will discuss subjects such as setting up credits time per game awards etc the section be low will show how to enter into the programming mode and how to adjust many of the 5 operat ing parameters ENTERING SET UP MODE You must enter set up mode to adjust all of the game features This can be accomplished in the fol lowing manner 1 Open the game s coin door This is the upper door located on the upper right side of the lower cabinet 2 Locate the PROG button It is located on the left hand side of the bracket that is attached to the cash box enclosure 3 Press the PROG button You are now in the program mode CHANGING GAME SETTINGS When you push the PROG button you will notice that the credits display will show PR This confirms
14. in credit defective parts must be returned to I C E Inc at the customer s expense within 30 days After 30 days a 15 re stocking fee will apply to all returns ICE distributors are independent privately owned and operated In their judgment they may sell parts and or accessories other than those manufactured by 1 Inc We cannot be responsible for the quality suitability or safety of any 1 part or modification including labor that is performed by such a distributor Innovative Concepts in Entertainment 17
15. ne bad during operation NO CF error code and CF light blinks 2 Normal op eration during sound No CF error code and CF light off 2 Normal opera tion without sound playing or card removed and rein serted with power on No CF error code and CF light solid 2 error with CF access light driver Setting the game ID to 9 will enter burn in mode This mode can only be exited by a power cycle with the ID set to anything other then 9 This mode will cycle the audio and move the ball gate Additionally it will cycle the segments on all displays During this burn in the error conditions described above do not work For More Product Information On This 1600 Other Arcade and Amusment Products Visit www BMIGaming com MAINTENANCE amp TROUBLESHOOTING GENERAL CLEANING Clean the surfaces of the cabinet and decals with a com mercial cleaner such as 409 or Fantastic Do NOT use cleaners such as Wildcat pinball cleaner or alcohol It can take the finish off of the decals Use Pledge on all plastic and painted surfaces This product works especially well on clear plastics Please note that other spray polishes do not work as well MECHANICAL REPAIRS IT IS IMPORTANT TO USE ONLY ICE REPLACEMENT PARTS WHEN SERVICING YOUR GAME USING NON ICE APPROVED PARTS COULD VOID YOUR WAR RANTY AND COULD CAUSE SERIOUS DAMAGE TO THE GAME OR INJURY TO OTHERS ELECTRICAL REPAIR WARNING EXERCISE CAUTION WHENEVER WORK ING WITH ELECTRONICS
16. ss For More Product Information On This 1600 Other Arcade and Amusment Products Visit www BMIGaming com WARRANTY POLICY Inc warrants all components in new machines to be free of defects in materials and workmanship for the period listed below 180 days on Main PCB s Computers amp Motors m 1 year on all LCD monitor panels m 90 days on all other electronic and mechanical components m 30 days on all l C E repairs and parts purchases Inc shall not be obligated to furnish a warranty request under the following conditions m Equipment or parts have failed through normal wear and tear m Equipment has been subjected to unwarranted stress abuse or neglect m Equipment has been damaged as a result of arbitrary repair modification Products will only be covered under warranty by obtaining an C E authorized RMA To obtain an RMA please provide C E tech support with the game serial or original C E invoice and a detailed description of the failure or fault symptoms I C E Inc will assume no liability whatsoever for costs associated with labor or travel time to replace defective parts All defective warranty covered components will be replaced with new or factory refurbished compo nents equal to OEM specifications Inc will cover domestic UPS ground or comparable shipping costs during the warranty period Interna tional or expedited shipments are available for an additional charge To obta
17. uired to earn awards can still be disoensed The default value for this op tion is 0 2 This setting can give a predetermined amount of tickets REGARDLESS of points scored if mode 7 and mode 8 are also used MODE 7 GAME POINTS PER TICKET This adjusts how many points are needed for the game The settings for this mode are 10 to 50 tick ets The number displayed set the points required to win an award Setting this number to 0 will turn off the dispenser MODE 8 TICKET CAP This mode is used to set the minimum number of points needed to get any awards whatsoever The settings for this mode are 0 to 99 tickets Set the number to match the score you wish to achieve be fore awards are dispensed Setting this number to 0 turns the option off The default for this option is MODE 9 ATTRACT TYPE Use this setting to control the type of attract mode you would like Setting a 1 gives you attract mode sound only Setting a 0 turns the attract mode off The default for this mode is 1 MODE 10 ATTRACT TIME This mode determines the length of time between attract modes Change this number to change the amount of time in MINUTES between attract modes The settings for this mode can be adjusted from 1 to 60 minutes The default for this mode is 3 MODE 11 BONUS TICKETS This mode allows you to set the number of Bonus Tickets The settings for this mode are from O to

nba-hoop-troops-kids..

Contents

Download Pdf Manuals

Related Search

Related Contents