SliderDynamic Service Manual
Contents
1. og wi sj os 3 Use a vacuum to clean out any dust and dirt 4 Replace the cover and screws TOOLS NEEDED CLOTH MULTI PURPOSE CLEANER 1 With a mild multi purpose cleaner clean tracks and wheels inside the rails 2 Clean seat wheels 3 If machines are receiving excessive use clean daily TOOLS NEEDED CLOTH OIL 1 Pull chain out to the finish position and slowly retract back while oiling with cloth Do this from under the chain so it does not drip on the machine or your floor 2 Oil the full length of the chain 3 Row 250 meters to spread the oil out to the rest of the chain 4 This should be done only a few times a year based on use otherwise the oil can build up in the gears TIGHTENING THE BUNGEE NO TOOLS NEEDED 3 Pull bungee towards the larger opening in the keyhole to loosen or unlock Pull 2 inches through then tighten towards the narrow keyhole to lock into place Clip back on bottom pulley axle flat side to machine body 1 Lock the Slider and stand it up ai l uv i 2 Take one bungee clip off of the axle LN Sets a a y Repeat steps for opposite side Make sure both clips are back on the axle Slowly lower machine unlock the plate and row If it still feels loose repeat above steps 4 You may need to cut off any excess bungee If the bungee appears frayed or does not give ample tension after tightening it is time to replace y2. Take the back cover off using a 3mm Allen tool making sure not to strip bolts Use WD4o if not easily loosened 4 D 10 11 Use the screwdriver to hold the chain off of the drive sprocket Take a mallet and tap out the drive axle Unscrew the drive sprocket You may need pliers or vise grips Put the new drive sprocket on Tap drive axle back on making sure the chain can attach around it Put the chain on the drive sprocket Put the flywheel back on using 17mm wrenches to attach Put the flywheel cover back on screw in the 4 screws using a Phillips screwdriver SLIDERDYNAMIC 13 TOOLS NEEDED PHILLIPS SCREWDRIVER 3MM ALLEN WRENCH MALLET 2 17MM WRENCHES PLYERS If your rails are not traveling back and forth Check that the rail brackets are not bent or loose If they are bent take off the bracket try to straighten it out and put it back on Row to see if the rails are corrected If unable to straighten call customer support 800 455 9022 for a replacement If the brackets are not bent clean the wheels and check that they are spinning properly TOOLS NEEDED 5MM ALLEN WRENCH PARTS NEEDED SKID BRACKET L BRACKET BOLTS 1 Remove the 5mm bolts from the bracket and skid strip 3 While holding the skid bracket place the L bracket on top and align holes Place each bolt in hand tighten first then tighten with a 5mm Allen wrench REP
3. LACING THE RAIL WHEELS TOOLS NEEDED OMM ALLEN KEY 10MM WRENCH 1 Remove the rear base rail end caps MP a 2 Remove the bumpers 3 Slide rail back until wheels are exposed 4 Using a 5mm Allen Key and a 10mm wrench remove the wheels D 6 Assemble the wheel spacers on the outside and punch through the middle Insert the wheel from underneath the top rail 10 11 12 Screw the nut onto the bolt Tighten with wrenches Make sure the wheel can spin the thread of the bolt needs to come past the nut to lock Repeat the above steps on the other side Return the bumpers and covers Replace the front wheels Remove the front base rail covers and bumpers and slide the machine forward so the wheels are accessible Repeat Steps 4 9 Your Sliders wheels should now be replaced Test row to make sure rails are sliding properly SLIDERDYNAMIC 16 REPLACING THE SENSOR TOOLS NEEDED 3 Take small Phillips screwdriver and unscrew the sensor 3MM ALLEN WRENCH and peel off Look inside the machine and open the tabs that hold the cable Remove the sensor and cable PHILLIPS SCREWDRIVER SMALL PHILLIPS SCREWDRIVER 17MM WRENCH 1 Take a 3mm Allen wrench and loosen top back cover bolts 2 and remove Slide cover open 4 Replace with new sensor plug in the back of the monitor Run through the tabs inside the machine and out of the hole by the flywheel Peel off the cover so
4. SLIDERD YNAMIC SERVICE MANUAL Click on the orange text for the particular TABLE OF CONTENTS section you would like to see To get back to this page select the Slider Replacing the Chain 02 03 logo at the bottom of each page Replacing the Flywheel mn 04 If you have further questions or need to Replacing the Idler Sprocket 05 06 order any Spare parts please contact us Cleaning the Flywheel en 07 Cleaning the Rails cums 08 US 1 401 2647 77451 Oiling the Chain cnet 09 esheets elimina Tightening the Bungee 10 960 Metacom Ave Warren RI 02910 Replacing the Bungee ne 11 12 i Replacing the Drive Sprocket 13 0208 749 2292 Rail Troubleshooting omni 14 info crokeruk com i 19 Acton Park Estate Replacing the Rail Bracket 13 The Vale London W3 70E Replacing the Rail Wheels 16 Replacing the Sensor 17 Replacing the Seat Wheels 18 Replacing the Handle 19 Replacing the Foot Strap 20 21 2014 2015 WaterRower SLIDER CHAIN REPLACEMENT REQUIRED TOOLS ALLEN WRENCH TOOL SET SCREWDRIVER 1 Unplug Monitor Remove the monitor cover bolts 4 using a 3mm allen tool BE CAREFUL NOT TO STRIP THE BOLTS it is recommended on older machines to use Liquid Wrench or WD 40 apply pressure and slowly turn as to not strip 2 Remove the 3mm bolts 6 securing the front cover 3 Remove top 3mm bolts 2 holding the rear cover 4 10 11 12 13 14 Pull the bungee chain bloc
5. ee bracket or tie off so they don t slip into the machine 9 4 Me F Let 1I 4 Ti j SHS iE ees p3 2 w a i i i f r ng E AA i i TE E li Fi EFI pg q Es he Be i Ff Cai j T EE Pi f Lt i 7i EF i i F r i ria ae al iF Sr aa wh a es ie mi emt Se ny p bs ie ee m ime E Bacy F T ts PE is H rm J r 3 Take 3mm Allen wrench you may need to tap with a mallet and loosen the bolts on the monitor cover and the front cover Be careful not to strip turn slowly with pressure or apply WD 40 Liquid Wrench SLIDERDYNAMIC 2 Use 4mm Allen wrench to remove plastic cover 4 bolts D REPLACING THE IDLER SPROCKET ASSEMBLY 4 Take bungees and chain and move to the sides of the body use a tool or cloth to keep it off your paint 6 Put replacement assembly in Tighten with 4mm wrench on either side of the axle 5 Use two 4mm Allen wrenches on either side of idler 7 Move bungees and chain back to pulley system and put Sprocket assembly to loosen Once loose take the covers back on assembly out 8 Tighten all the covers and clip bungees back to the Bungee Chain Block axle 9 Oil chain to smooth out and quiet the new sprocket system SLIDERDYNAMIC b TOOLS NEEDED PHILLIPS SCREWDRIVER VACUUM 1 Take screws 4 out of the Flywheel Cover 2 Remove Flywheel Cover
6. k pulley up above the footplate and secure using a screwdriver Undo the bolt holding the connector end of the chain Remove the original chain Remove the chain from the handle end by undoing the two socket inserts on the rower side of the handle Pull the U Bolt from the handle Undo one insert nut and slide the chain swivel end of the chain off Attach the new chain Thread the insert nut and turn until it is equal with the other side on the U bolt Insert the U bolt into the handle Secure the U bolt with the socket insert nuts Once attached to the handle place the handle on the top rails and straighten the chain out CEA T SLIDERDYNAMIC 2 SLIDER CHAIN REPLACEMENT 15 16 17 18 19 20 Insert the open end of the chain through the plastic chain faring opening Thread the chain over the top sprocket then down to the second drive sprocket on the flywheel drive shaft Thread the chain over the large plastic pulley then down towards the footplate Insert the chain around the small pulley on the bungee chain block Thread the chain back up and over the small idler pulley then back down to the chain bungee block pulley i _ Holding the chain insert one chain clip into the two end links on the chain Insert the other chain clip in the opposite direction of the same two links the first chain clip is attached to 21 Thread the bolt through the connector pla
7. our bungee SLIDERDYNAMIC 10 REPLACING THE BUNGEE TOOLS NEEDED 6 Insert the new bungee in bungee block 3MM ALLEN WRENCH 4MM ALLEN WRENCH 1 Lock the machine 2 Take the 6 bolts off the front cover off using 3mm Allen wrench Take the black cap off using a 4mm Allen wrench 7 Pull tight and line up Z Stand hi 3 Stand machine up 8 Take right bungee piece and tie off on foot straps 4 Take note of how the bungees are wrapped and parallel not crossed before taking out old bungee 5 Unhook bungees unlock and slide out of hooks cont on next page SLIDERDYNAMIC 11 REPLACING THE BUNGEE 9 Take left bungee up and around Feed into machine to top pulley then feed it up and around 10 Place bungee in hook and lock to small side of keyhole flat side to the body 11 Take the right side of the bungee and hook down and around Feed into machine to top pulley Feed downward and around 12 Attach the bungee hook to the axle flat side to body Make sure bungees are parallel if they are crossed recheck your steps SLIDERDYNAMIC 12 REPLACING THE DRIVE SPROCKET TOOLS NEEDED PHILLIPS SCREWDRIVER 3MM ALLEN WRENCH MALLET 2 17MM WRENCHES PLIERS 1 With the Slider Flywheel forward unscrew the 4 Flywheel screws using a Phillips screwdriver 2 Loosen the drive axle bolts using 17mm wrenches then take bolts off and remove flywheel 3
8. t it does not retract into the machine 3 Hook on the handle rest 4 Take the new handle and slide it into U Bolt 5 Insert 5mm bolts and tighten FOOT STRAP REPLACEMENT REQUIRED TOOLS 7MM WRENCH PHILIPS SCREWDRIVER 1 Using the 7mm wrench locate the small nut on the back of the footboard Hold the nut with the wrench Using the screwdriver unscrew the middle inside bolt 2 Remove the screw bolt and old strap Place screw nearby for reuse 4 Loop the new foot strap through with the buckle part towards the middle of the footboard Note the hole in the foot strap line up the hole in the strap with the screw hole in the footboard Insert the screw through the footboard and hole in the foot strap SLIDERDYNAMIC 20 FOOT STRAP REPLACEMENT 5 Take the nut and insert it into the wrench put your 8 finger on the back of the wrench to hold the nut in place then place on the screw thread on the back of the Feed the strap through the buckle The Footstrap assembly is now complete Repeat on the other side if necessary footboard ET 6 While holding with the wrench tighten the screw with a Philips screwdriver 7 Take the remaining part of the strap and feed through the outer slot SLIDERDYNAMIC 21
9. te and tighten the nut 22 Pull the handle to make the bungee chain block plate move up and remove the screwdriver that was securing the block in place 23 Check that the chain is running smoothly and correctly around all sprockets and pulleys Use the threading procedure picture as a guide 24 Replace all covers and reattach monitor cable SLIDERDYNAMIC 3 REPLACING THE FLYWHEEL REQUIRED TOOLS 17 MM WRENCH 2 PHILIPS HEAD SCREWDRIVER MALLET 1 Take screws 4 out of the Flywheel Cover Remove Cover 2 4 Loosen flywheel nut take off spacer and nut and remove flywheel If the flywheel won t come off put the nut back on the end of the shaft and tap the nut with the mallet This will loosen the flywheel and allow you to remove it si ht Si TT r Er ANI aaa Replace with new flywheel You may need to tap on the opposite side of the shaft for it to slide on all the way Take the spacer and nut and put back on the shaft Tighten bolts on both sides of the shaft Take a few strokes to check that is not too tight If it is too tight the chain won t recoil properly Put flywheel cover back on and put the screws back in SLIDERDYNAMIC 4 REPLACING THE IDLER SPROCKET ASSEMBLY REQUIRED TOOLS 2 4MM ALLEN KEYS 3MM ALLEN KEY VICE GRIPS OR PLIERS CLOTH 1 To release bungee pressure stand the machine up and unclip bungees from the axle Clip on the safety bung
10. the sticky adhesive is exposed line up with screw hole and Stick 5 Tighten sensor screw 6 Replace flywheel using 17mm wrench Attach the 2 Take flywheel cover off using a Phillips Screw Driver flywheel cover using a Philips screwdriver Using a 17mm wrench loosen flywheel bolt Remove bolt 7 Attach rear cover Insert bolts and tighten with a 3mm and flywheel Allen key SLIDERDYNAMIC 17 TOOLS NEEDED 4 Screw nut on and tighten until the bolt has passed 5MM ALLEN KEY the lock nut thread In order to ensure the wheel spins 13MM WRENCH freely be sure not to overtighten PHILLIPS SCREWDRIVER 1 Remove screws from the rear top rail endcaps and remove endcaps 5 Repeat above steps until all the wheels have been replaced 6 Put the seat back on the top rail Make sure the indent is towards the back of the machine 2 Slide the seat off Using the 5mm Allen key and 13mm wrench remove the nut and bolt 7 Replace the end caps and screws 3 Take the old wheel off and put the new one on Make sure to put washer on one side of the bolt and the Spacer on the other The easiest way to do this is to put the bolt partially through put on the washer put the wheel on partially slide bolt through the wheel to hold wheel insert the spacer push bolt through TOOLS NEEDED OMM ALLEN KEY 1 Use a5mm allen key and remove handle bolts 2 Take the U Bolt out of the handle be careful tha
Download Pdf Manuals
Related Search