Home

Heat recovery units

image

Contents

1. A TIPO B TIPO C TIPO D TYPE A TYPE B TYPE C TYPE D a ili lt a D A E ba ISS ar fe C Zr ii Sen fi A a E ignora Fig 03 MEKAR mekar it Manuale di installazione uso e manutenzione Installation and maintenance manual NORME DI SICUREZZA Il Produttore declina qualsiasi responsabilit per l inosservanza delle Nor me di sicurezza e di prevenzione di seguito riportate Declina inoltre ogni responsabilit per danni causati dall uso improprio dell apparecchio e o da modifiche eseguite senza autorizzazione L installazione deve essere effettuata da personale qualificato Durante l installazione usare un abbigliamento consono antinfortunistico come indicato nelle normative Durante l installazione operare in sicurezza in un ambiente libero da impedimenti e pulito Rispettate le leggi in vigore nel Paese in cui viene installato l apparecchio rela tivamente all uso ed allo smaltimento dell imballo e dei prodotti impiegati per la pulizia e la manutenzione della macchina Evitare di toccare le parti in movimento dell apparecchio Prima di accendere l apparecchio controllare l integrit dei vari componenti Non procedere con la manutenzione o la pulizia se prima non stata disinserita l alimentazione elettrica La manutenzione e sostituzione di parti danneggiate o usurate dev essere ese guita unicamente da pers
2. UTILIZZATORE 4 YMEKAR AIR HANDLING UNITS INTRODUCTION At the moment the unit is delivered make sure that it corresponds to the one indicated on the transport document Check that the packaging and the unit are intact Should there be any differences compared to the original order or any damage anoma lies or incomplete supply please report it on the delivery note and inform the company immediately Never install or use damaged appliances A qualified firm must install the appliance and upon completion of work issue the owner the declaration of conformity of installation with current regulations and standards and with the instructions provided in this booklet Under no circumstances can the Company be held liable for damage caused to property or injury to persons or animals due to incorrect installation regulation and maintenance or to misuse RECOMMENDATIONS Using electrically operated products connected to the water supply implies the observance of certain basic safety rules Do not allow children or unassisted handicapped persons to use the unit Do not touch the unit with wet parts of the body or if barefoot Do not tug pull or twist electrical cables attached to the unit even when discon nected from the electricity supply Do not open the flaps giving access to the internal parts of the unit without having first put the system on off switch to off Do not alter the safety or contr
3. ma uscendo direttamente all esterno passando per un canale collegato alla bocca 2 necessario ordinare uno speciale pannello completo del foro L aria di rinnovo passa attraverso il filtro ed il recuperatore senza scambi di ca lore Per utilizzare la modalit free cooling bisogna quindi costruire una canalizzazione da unire alla bocca e predisporre 2 due serrande la serranda 1 deve essere aperta e la serranda 3 deve essere chiusa vedi figura 08 FREE COOLING The free cooling mode is used so that stale air coming from the room is not expel led through the recovery unit but passes directly to the exterior through a duct connected to outlet 2 a special panel with hole must be ordered The incoming fresh air passes through the filter and recovery unit without any exchanges of heat To use the free cooling mode a duct must be connected to the outlet and two dam pers fitted damper 1 must be open and damper 3 must be closed see Fig 08 Espulsione dell aria viziata 4 Stale air outlet A lt AMBIENTE ESTERNO EXTERNAL AMBIENT E gt AMBIENTE INTERNO INTERNAL AMBIENT Immissione aria di rinnovo Fresh air inlet Fig 08 mekar it ME 11 AIR HANDLING UNITS Manuale di installazione uso e manutenzione Installation and maintenance manual JIMPN CO
4. mekar it Manuale di installazione uso e manutenzione Installation and maintenance manual b Fig 10 6 Replace the filter when it is perfectly dry Fig 11 N B Pulire il filtro all inizio ed alla fine di ogni stagione o compatibilmente con l attivit svolta B Verifica dello scarico condensa bacinella Per il controllo e la manutenzione di tale bacinella togliere le viti nella parte infe riore dell apparecchio C Verifica del recuperatore Accertarsi che lo scambiatore sia libero da ogni tipo di impurit che potrebbero abbassare sensibilmente la sua efficienza D Verifica della batteria post riscaldamento ad acqua se presente Accertarsi che lo scambiatore sia libero da ogni tipo di impurit che potrebbero abbassare sensibilmente la sua efficienza MANUTENZIONE MENSILE A Controllo di tutta l apparecchiatura elettrica ed in particolare il serraggio delle connessioni elettriche B Controllo che il serraggio di tutti i bulloni flange dadi e connessioni idriche sia saldo RICERCA DEI GUASTI ATTENZIONE Nel caso di malfunzionamento odore di bruciato o altro fermare il funziona mento immediatamente staccare l alimentazione e consultare il personale di servizio autorizzato Spegnendo l unit l alimentazione elettrica non viene scollegata completa mente Quindi assicuratevi sempre di staccare l interruttore generale in modo da garantire che l unit sia comp
5. pi corto possibile Non deve inoltre avere curve a gomito troppo strette o ostruzioni di qual siasi tipo o provocare sollecitazioni sull attacco all unit For good installation and correct operation the following are recommended installation of a trap to prevent unpleasant odours rising complete with plug for cleaning in the lower part if this is impossible regular maintenance and cleaning must be facilitated the condensate drain pipe must slope down towards the exterior and be as short as possible It must not have sharp bends or be obstructed in any way or put stress on the unit fitting VISTA IN PIANTA PLAN VIEW VISTA IN SEZIONE SECTION VIEW Fig 06 10 MEKAR AIR HANDLING UNITS mekar it Manuale di installazione uso e manutenzione Installation and maintenance manual COLLEGAMENTO EVENTUALE BATTERIA AD ACQUA DI POST RISCALDAMENTO CONNECTION OF ANY WATER RE HEAT COIL La batteria post riscaldamento se presente ha attacchi maschio da 1 2 filet tatura gas Fissare i tubi di alimentazione usando chiave controchiave Sull unit segnalata con un etichetta l attacco di entrata e quello di uscita dell acqua In caso di estrazione della batteria post riscaldamento non devono esserci osta coli si consiglia quindi di semplificare il percorso delle tubazioni Coibentare le tubazioni che arrivano alla batteria per evitare la poss
6. ANTINFORTUNISTICA A NORMA UNI 9219 E SUCCESSIVE I canali devono essere dimensionati in funzione dell impianto e delle caratteristi che aerauliche dei ventilatori dell unita Un errato calcolo delle condutture di cana lizzazione pu provocare il malfunzionamento es perdita di potenza dell appa recchio o l intervento di eventuali dispositivi presenti nell impianto Per evitare di trasmettere le eventuali vibrazioni della macchina in ambiente consigliato l uso di giunti anti vibranti fra le bocche ventilanti ed i canali Deve inoltre essere garantita la continuit elettrica fra ca nale e macchina tramite un cavo di terra Per evitare la formazione di condensa ed attenuare il livello di rumorosit consiogliato utilizzare delle canalizzazioni coibentate COLLEGAMENTI IDRAULICI Il collegamento delle tubazioni idrauliche un operazione che se non eseguito a regola d arte da personale specializzato pu compromettere il buon funzionamen to dell impianto o causare danni irreparabili all apparecchio SCARICO CONDENSA La bacinella raccolta condensa delle unit di recupero calore in lamiera zincata con uno scarico da 20 mm Per il controllo e la manutenzione di tale bacinella togliere le viti nella parte inferiore dell apparecchio DUCT CONNECTION IMPORTANT UNDER NO CIRCUMSTANCES SWITCH THE UNIT ON IF THE FAN OUTLETS HAVE NOT BEEN DUCTED OR PROTECTED WITH SAFETY MESH TO UNI 9219 AND SUBSEQUENT STANDARDS The duc
7. INSTALLATION AND MAINTENANCE MANUAL Manuale di installazione uso e manutenzione Heat recovery units Unit di recupero calore e MEKAR AIR HANDLING UNITS Net Manuale di installazione uso e manutenzione Installation and maintenance manual INDICE PREMESSA AVVERTENZE IDENTIFICAZIONE DELL APPARECCHIO TRASPORTO RICEVIMENTO MOVIMENTAZIONE PRESCRIZIONI DI SICUREZZA DESCRIZIONE GENERALE DELL APPARECCHIO DIMENSIONI GENERALI RECUPERATORE COMPOSIZIONE PRINCIPALE DATI TECNICI RECUPERATORE FLUSSI D ARIA INCROCIATI NORME DI SICUREZZA SCELTA DEL LUOGO PER L INSTALLAZIONE COLLEGAMENTO Al CANALI COLLEGAMENTI IDRAULICI Scarico condensa COLLEGAMENTO EVENTUALE BATTERIA AD ACQUA DI POST RISCALDAMENTO FREE COOLING COLLEGAMENTI ELETTRICI CONTROLLI AL PRIMO AVVIAMENTO MANUTENZIONE Manutenzione mensile RICERCA DEI GUASTI COSA FARE SE SMANTELLAMENTO DELL APPARECCHIO mekar it INDEX INTRODUCTION RECOMMENDATIONS IDENTIFICATION OF THE UNIT TRANSPORTATION STORAGE AND HANDLING SAFETY RULES GENERAL DESCRIPTION OF THE UNIT GENERAL DIMENSIONS MAIN PARTS GENERAL TECHNICAL DATA 7 CROSS FLOW 8 SAFETY RULES 8 SELECTION OF INSTALLATION LOCATION 8 DUCT CONNECTION 8 WATER CONNECTIONS 8 Condensate drainage 9 CONNECTION OF ANY WATER RE HEAT COIL 9 FREE COOLING 9 ELECTRICAL CONNECTIONS 9 CONTROLS AT FIRST TIME OF STARTING 10 MAINTENANCE 10 Monthly m
8. LLEGAMENTI ELETTRICI 1 Inserire il cavo di connessione nella morsettiera saldamente L inserimento er rato potrebbe essere causa di corto circuito o incendio 2 Assicurarsi di collegare il cavo di terra 3 Eseguire il cablaggio in conformit con le normative in modo che l unit possa funzionare correttamente 4 Prima di allacciare la corrente assicurarsi che il voltaggio sia nel limite di po tenza di esercizio 10 5 Usare sempre una linea indipendente 6 Il cavo non deve avere giunzioni 7 Tutte le unit vanno adeguamente fornite di messa a terra cos che l utente possa operare in sicurezza 8 La capacit della fonte di energia deve essere la somma della corrente dell uni t e quella delle altre apparecchiature elettriche utilizzate Quando la capacit di servizio della corrente insufficiente bisogna procedere all adeguamento della stessa CONTROLLI AL PRIMO AVVIAMENTO Controllare il corretto fissaggio a soffitto e delle eventuali barre di sostegno au siliarie Verificare l esatto posizionamento dei pannelli Assicurarsi che nella eventuale batteria ad acqua post riscaldamento non sia presente dell aria in caso contrario agire sulla valvolina di sfiato Controllare che il cavo di terra per l unit sia stato collegato Controllare che i cavi di terra per le parti elettriche siano stati collegati Assicurarsi che i tubi per le eventuali batterie ad acqua post riscaldamento siano stati ad
9. R might modify even without any prior notice the given technical data MEKAR AIR HANDLING UNITS Mekar s r l e Viale Caduti sul Lavoro 25 37063 ISOLA DELLA SCALA VR Tel 39 045 6630536 fax 39 045 6630513 info mekar it www mekar it
10. aintenance 10 TROUBLESHOOTING 10 WHAT TO DO IF 11 DISMANTLING THE APPLIANCE MEKAR AIR HANDLING UNITS 10 10 10 10 11 Manuale di installazione uso e manutenzione Installation and maintenance manual JIMPN Controllare al momento della consegna dell apparecchio che corrisponda a quello indicato sul documento di trasporto Verificare l integrit degli imballi e dell unit stessa Se si dovessero riscontrare incongruenze con l ordine anomalie danni o for nitura incompleta indicarlo sulla bolla di consegna e avvertire tempestivamente l azienda NON installare ne utilizzare apparecchi danneggiati L installazione dell apparecchio deve essere effettuata da impresa abilitata che a fine lavoro rilasci al proprietario la dichiarazione di conformit di installazione rea lizzata a regola d arte cio in ottemperanza alle Norme vigenti ed alle indicazioni fornite in questo libretto esclusa qualsiasi responsabilit per danni causati a persone animali o cose da errori di installazione di regolazione e di manutenzione o da usi impropri AVVERTENZE L utilizzo di prodotti che impiegano energia elettrica ed acqua comporta l osservanza di alcune regole fondamentali vietato l uso dell apparecchio ai bambini e alle persone inabili non assistite vietato toccare l apparecchio se si a piedi nudi e con parti del corpo bagnate o umide vietato tirare staccare torcere i cav
11. d air flow Filtri aria Air filters Efficienza di filtrazione Filtration efficiency G3 G3 G3 G3 G3 G3 Assorbimenti elettrici Max motore Power supply Assorbimento massimo Maximum absorption A 2x0 95 2x1 5 2x1 5 2x3 1 2x3 0 2x5 9 Potenza disponibile all asse Power available for ass y Ww 2x90 2x160 2x147 2x350 2x350 2x550 Alimentazione elettrica Max motor input W Ph Hz 230 1 50 230 1 50 230 1 50 230 1 50 230 1 50 230 1 50 mekar it e MEKAR 7 Manuale di installazione uso e manutenzione Installation and maintenance manual JIMPN FLUSSI D ARIA INCROCIATI CROSS FLOW Immissione aria di rinnovo Fresh air outlet AMBIENTE INTERNO INTERNAL AMBIENT Espulsione dell aria ambientale Stale air inlet Espulsione dell aria ambientale Stale air inlet Espulsione dell aria ambientale Stale air outlet de N N qee AMBIENTE ESTERNO EXTERNAL AMBIENT Immissione aria di rinnovo r J Fresh air inlet la e Immissione aria di rinnovo Fresh air inlet AIR HANDLING UNITS TIPO
12. eguatamente isolati Assicurarsi che i canali siano collegati all unit MANUTENZIONE ATTENZIONE Prima di eseguire qualsiasi intervento di pulizia o manutenzione staccare l apparecchio dalla rete elettrica Non utilizzate acqua per la pulizia per nes sun motivo dovere dell utilizzatore far eseguire periodicamente tutte le operazioni di ma nutenzione Le operazioni di manutenzione possono essere eseguite SOLO da personale qualificato In caso di smontaggio delle parti necessario proteggere le mani con guanti da lavoro MANUTENZIONE MENSILE A Pulizia del filtro 1 Svitare le 2 viti di fissaggio e togliere la placca porta filtro 2 Estrarre il setto filtrante ELECTRICAL CONNECTIONS 1 Insert the connecting cable firmly into the terminal block Incorrect insertion could cause a short circuit or fire 2 Ensure that the earth wire is connected 3 Carry out the wiring in conformity with regulations to ensure correct unit ope ration 4 Before connecting to the mains electricity supply make sure that the voltage is within the working power limit 10 5 Always use an independent line 6 The cable must not have joints 7 All the units must be suitably earthed so that the user may operate in all safety 8 The capacity of the electrical system must be sufficient for powering the unit and other electrical appliances commonly used Whenever the supply current capacity is insufficient it must be s
13. el luogo di installazio ne La movimentazione deve essere effettuata con la massima cura mantenendo sempre l apparecchio nel proprio imballo originale TRASPORTO Il trasporto dell unit dev essere effettuato in sicurezza Il peso di ogni singola macchina riportato in questo manuale Le unit ed i loro accessori vengono trasportate su pallets Gli imballi dovranno rimanere integri fino al momento del montaggio Durante il trasporto l unit e gli accessori se presenti non deve essere sottoposta ad urti rischio di dannegio struttura componenti interni l unit e gli accessori se presenti deve essere fissata sul piano di trasporto tramite funi o altro mezzo che ne impedisca il movimento deve essere garantita la protezione delle parti sporgenti dell unit attacchi idrau lici scarico condensa parti elettriche etc non esporre l unit e gli accessori se presenti agli agenti atmosferici STOCCAGGIO E MOVIMENTAZIONE DELL UNIT L unit se non installata subito pu essere immagazzinata in locali protetti dal le intemperie con temperature comprese tra i 20 C ed i 55 C AI momento dell installazione trasportare l apparecchio imballato il pi vicino possibile al luo dell installazione La movimentazione e l istallazione pu essere facilitata dall uso dell elevatore PRESCRIZIONI DI SICUREZZA Non lasciare gli imballi sciolti durante il trasporto Non esporre agli agenti atmosferici N
14. er is easily accessible Do not install the appliance in environments where aggressive or corrosive acid substances are present risk of irreparable damage to the unit and its accessories Choose a place for installation where there is sufficient space to carry out instal lation work and subsequent maintenance Ductwork near the unit must not have sharp bends or branches Make sure that the installation does not interfere with existing electric wiring or plumbing Establish the position and size of the hole in the ceiling Select the final position of the unit in the ceiling Use the threaded bar with suitable screw anchors to fix the unit to the ceiling as shown in figure 4 material not included in the supply The use of supplementary supporting bars is recommended NOTE install the unit with an inclination of 3 mm towards the condensate drain outlet to ensure a regular flow of condensate x consigliato l utilizzo di barre di sostegno supplementari The use of Antivibrante supplementary in gomma supporting bars is Rubber recommended anti vibration Fig 04 ME mekar it 9 AIR HANDLING UNITS Manuale di installazione uso e manutenzione Installation and maintenance manual JIMPN COLLEGAMENTO Al CANALI IMPORTANTE E VIETATO METTERE IN FUNZIONE L UNITA SE LE BOCCHE DEI VENTILATORI NON SIANO STATE CANALIZZATE O PROTETTE CON RETE
15. ernal rotor motor 230V 50Hz 2 poles for the 01 and 02 models or 4 poles for the larger models class F insu lation complete with vibration isolation mountings HEAT RECOVERY UNIT Cross flow air to air static type heat recovery unit Pla tes and suitably sealed retaining frame in aluminium Steel condensate collecting tray with drain pipe FILTERS Polyester filters with average volumetric efficiency 86 5 Am and effi ciency class G3 to EN779 Manuale di installazione uso e manutenzione i Installation and maintenance manual GENERAL DIMENSIONS DIMENSIONI GENERALI Lu lt q E B f o o AC B A Fig 01 MOD 01 02 03 04 05 06 A mm 290 390 390 490 490 590 B mm 870 970 1 120 1 220 1 370 1 470 c mm 770 770 870 870 1 020 1 175 D mm 344 344 393 393 469 546 E mm 232 332 332 432 432 532 F mm 224 225 230 230 300 265 G mm 114 115 210 260 260 289 COMPONENTI PRINCIPALI MAIN PARTS Fig 02 1 Coclea ventilatore centrifugo Centrifugal fan scroll 5 Filtro aria Air filter 2 Resistenza elettrica se presente Heating element if installed 6 Attacco scarico condensa 922 mm Condensate drain fitting 22 mm 3 Ventilatore centrifugo Centrifugal fan 7 Angolare Angle bar 4 Recuperatore di calore Heat recovery unit 8 Pannellatura isolata termo acus
16. go per l installazione in maniera tale che attorno alla macchina vi siano spazi adatti per l installazione e la successiva manutenzione In vicinanza dell unit le canalizzazioni non devono presentare bruschi raccordi o deviazioni Verificare che l installazione non interferisca con l impianto elettrico o idraulico gi esistente Determinare la posizione e la dimensione del foro sul soffitto Scegliere la posizione finale dell unit nel softitto Per il fissaggio dell unit al soffitto utilizzare della barra filettata con dei tasselli adeguati come illustrato nella figura 4 materiale non incluso nella fornitura consigliato l utilizzo di barre di sostegno supplementari NOTA montare l unit inclinata di 3 mm verso la scarico condensa per favo rire il deflusso della condensa in modo regolare SAFETY RULES Failure to comply with the safety and prevention rules given below relieves the Manufacturer from all and any liability Neither can the Manufacturer be held responsible for damage caused by misuse of the appliance or by unauthorised alterations Installation must be carried out by qualified personnel Wear suitable safety clothing during installation as recommended by applica ble regulations and legislation During installation work in safety by ensuring the environment is free from ob stacles and clean Comply with the laws in force in the country in which the appliance is being in stalled with regard to u
17. i elettrici fuoriuscenti dall apparecchio an che se questo scollegato dalla rete di alimentazione elettrica vietato aprire gli sportelli di accesso alle parti interne dell apparecchio senza aver prima posizionato l interruttore generale dell impianto su spento vietato modificare i dispositivi di sicurezza o di regolazione senza l autorizza zione e le indicazioni del costruttore dell apparecchio vietato sedersi salire con i piedi sull apparecchio e o appoggiarvi qualsiasi tipo di oggetto vietato introdurre oggetti appuntiti attraverso le griglie di aspirazione e mandata aria vietato disperdere abbandonare o lasciare alla portata dei bambini il materiale dell imballo cartine graffe sacchetti di plastica ecc in quanto pu essere fonte di pericolo vietato spruzzare o gettare acqua direttamente sull apparecchio vietato l uso dell apparecchio in luoghi con polveri sospese o in atmosfere potenzialmente esplosive in ambienti con presenza di olio in sospensione molto umidi o in presenza di atmosfere particolarmente aggressive vietato coprire l apparecchio con oggetti che ostruiscano anche parzialmente il flusso dell aria L apparecchio funziona mediante energia elettrica alla tensione di rete 230 Vca 50Hz Tenete sempre presente che la tensione di rete potenzialmente pericolo sa e che qualsiasi apparecchio ad essa collegato va utilizzato con attenzione Pri ma di effettuare
18. ibile forma zione di condensa Staffare adeguatamente le tubazioni in maniera da non pesare sulla batteria post riscaldamento o sull unit consigliabile installare un dispositivo antigelo accessorio consigliabile installare valvole di intercettazione per isolare la batteria incaso di manutenzione o riparazioni Nel caso l unit debba rimanere fuori servizio per un lungo periodo specialmente nelle zone con clima molto rigido si consiglia di svuotare l impianto The re heat coil if installed has v2 male fittings gas thread Fix the supply pipes using wrench counter wrench The water inlet and outlet fittings are marked on the unit with a label There must be no obstacles to removing the re heat coil it is therefore recom mended that the pipework route be simple Lag the pipes leading to the coil to prevent any formation of condensation Suitably support and clamp the pipework so that it does not weigh on the re heat coil or on the unit It is advisable to install a frost protection device accessory It is advisable to install shutoff valves to isolate the coil during maintenance or repair If the unit is not going to be used for long periods especially in very cold areas it is advisable to drain the system Fig 07 FREE COOLING La modalit free cooling prevede che l aria viziata proveniente dall ambiente non non venga espulsa passando attraverso il recuperatore
19. interventi sull apparecchio scollegatelo dalla rete elettrica stac cando la spina di alimentazione o isolando la linea di alimentazione spegnendo l interruttore generale Se l apparecchio non viene utilizzato per lunghi periodi assicuratevi che i co mandi siano in posizione O spento Se l apparecchio dovesse rimanere fermo d inverno con temperature prossime allo zero vuotate l impianto ed assicuratevi che lo scambiatore dell apparecchio sia completamente privo d acqua per evitare rischi di formazione di ghiaccio e conseguente rottura Se l apparecchio deve essere messo definitivamente fuori servizio scollegatelo in modo definitivo dalla rete elettrica E rischioso modificare o tentare di modificare le caratteristiche di questo pro dotto In ogni caso la manomissione o modifica comporta l immediata esclusione della garanzia In caso di guasto non cercate mai di riparare l apparecchio da soli rivolgetevi a tecnici qualificati Le riparazioni effettuate da persone non competenti possono causare danni o incidenti Tenete sempre ben pulito l apparecchio in particolare pulite periodicamente il filtro aria se presente almeno una volta al mese IL PRODUTTORE DECLINA OGNI RESPONSABILIT QUALORA NON VE NISSERO RISPETTATE LE ISTRUZIONI PER IL MONTAGGIO RIPORTATE IN QUESTO MANUALE LA NON CORRETTA INSTALLAZIONE POTREBBE CAU SARE IL CATTIVO E O MANCATO FUNZIONAMENTO DELL APPARECCHIO POTREBBE INOLTRE ESSERE FONTE DI RISCHIO PER L
20. izzata nello smaltimento differenziato dei rifiuti solo cos avrete la certezza di un riciclaggio corretto e contribuirete al rispetto dell ambiente NOTE Strong vibrations unbalanced fan wheel due to wear or accumulation of dust scraping of the fan wheels along the scroll due to deformation the ducts could be obstructed SMANTELLAMENTO DELL APPARECCHIO Questo apparecchio costruito per durare molti anni In caso di smantellamento richiedete l intervento di personale qualificato affinch il lavoro venga svolto nella massima sicurezza Ricordate sempre che la prima operazione da svolgere prima dello smantellamento dell apparecchio di scollegarlo in modo definitivo dalla rete elettrica Questo apparecchio costruito utilizzando materiali riciclabili rame alluminio ottone plastica assemblati mediante viti e incastri in modo da facilitare le opera zioni di separazione delle parti Rivolgetevi ad una ditta specializzata nello smaltimento differenziato dei rifiuti solo cosi avrete la certezza di un riciclaggio corretto e contribuirete al rispetto dell ambiente NOTES 14 MEKAR AIR HANDLING UNITS mekar it 2015 0 In un ottica di miglioramento e a fronte della costante azione di ricerca e sviluppo MEKAR si riserva di modificare anche senza preavviso i dati tecnici riportati With the perspective of improvement and against the continuos action of research and development MEKA
21. letamente staccata dall alimentazione elettri ca mekar it MEK NIT NOTE Clean the filter at the start and end of every season or more frequen tly considering unit activity B Checking the condensate drain tray To check and maintain this tray remove the screws from the bottom of the ap pliance C Checking the recovery unit Check the exchanger for impurities that could considerably reduce its efficiency D Check the water re heat coil if installed Check the exchanger for impurities that could considerably reduce its efficiency MONTHLY MAINTENANCE A Check the entire electrical part and in particular that the electrical connections are tight B Check the tightness of all the bolts flanges nuts and water connections TROUBLESHOOTING CAUTION In the event of malfunction smell of burning or similar stop operation im mediately cut off the electricity supply to the unit and contact an authorised service centre The electricity supply is not fully cut off by simply switching off the unit Always makes sure therefore that the main on off switch is put to off to ensure that the unit is fully disconnected from the power supply 13 Manuale di installazione uso e manutenzione Installation and maintenance manual JIMPN COSAFARE SE Il motore non gira Controllare che l alimentazione sia inserita gli interruttori o i termostati siano nella posizione di funzionamento non vi siano cor
22. ng it in its original packaging TRANSPORTATION The unit must be transported in all safety The weight of each single appliance is given in this guide The units and their accessories are transported on pallets The packaging must not be removed until the units are to be installed During transportation the unit and any accessories must not be subjected to impact risk of damage to structure internal parts the unit and any accessories must be fixed to the surface of the means of tran Sport by ropes or such to prevent movement the projecting parts of the unit water fittings condensate drain electrical parts etc must be protected do not expose the unit or any accessories to the elements STORING AND HANDLING THE UNIT The unit may be stored in rooms protected against inclement weather at a tempe rature between 20 C and 55 C When installing put the packaged unit as near as possible to the place of installa tion Handling and installation can be facilitated by using a forklift truck SAFETY RULES Secure packs during transportation Do not expose to the elements Do not tread on packs eo Protect hands with work gloves when dismantling the appliance Work in PAIRS if the applinance weighs more than 25 kg GENERAL DESCRIPTION OF THE UNIT FAN SECTIONS Air supply and intake ventilation section with centrifugal double inlet forward curved blade fans directly coupled to the single phase ext
23. ol devices without permission and instructions by the manufacturer of the appliance Do not sit climb onto or place any objects on top of the appliance Do not insert sharp pointed objects through the air intake and outlet grilles Do not leave packaging material boards staples plastic bags etc within reach of children but dispose of properly since it could be a source of danger Do not spray or direct water directly onto the unit Do not use the unit in places with suspended dust powder or in potentially explo sive atmospheres in very damp environments or in the presence of oil in suspen sion or in particularly aggressive atmospheres Do not cover the unit with objects that even partially obstruct the air flow The unit works by electricity at mains voltage 230 Vac 50 Hz Always bear in mind that mains voltage is potentially dangerous and any appliance connected to it should be used with caution Before carrying out any work on the unit disconnect it from the electricity supply by pulling out the plug from the mains socket or isolating the supply line by putting the on off switch to OFF If the unit is not to be used for long periods make sure that the controls are in the position 0 off If the unit is not going to be used in winter when temperatures are near to free zing drain the system and ensure that the unit heat exchanger has no water in it in order to prevent the formation of ice and consequent b
24. on calpestare eo Se l apparecchio deve essere smontato proteggere le mani con guanti da lavoro NON spostare da soli la macchina se il suo peso supera i 25 Kg DESCRIZIONE GENERALE DELL APPARECCHIO SEZIONI VENTILANTI Sezione ventilante di mandata e aspirazione con ventila tori centrifughi a doppia aspirazione pale avanti direttamente accopiati al motore elettrico a rotore esterno monofase 230V 50Hz 2 poli per i modelli 01 e 02 o a 4 poli per i modelli superiori isolamento in classe F completi di supporti antivibranti RECUPERATORE DI CALORE Recuperatore di calore di tipo statico aria aria a flussi incrociati Piastre in alluminio e telaio di contenimento in alluminio opportu namente sigillato Baccinella di raccolta condensa in acciaio con tubo di scarico FILTRI Filtri in poliestere di efficienza volumetrica media 86 5 Am e classe di efficienza G3 secondo EN779 mekar it ME IDENTIFICATION OF THE UNIT The units come with a rating plate which shows CE marking Nominal air flow m3 h Model Rated absorbed current in A Input W Date of manufacture Recovery unit heat output W Lot number Static pressure Pa TRASPORTATION RECEIVING HANDLING The unit is delivered enclosed in special protective packaging which must remain intact until the unit has been located in its final place of installation The unit must be handled with the utmost care keepi
25. onale specializzato In caso di smantellamento dell apparecchio attenersi alle normative vigenti in materia NOTA BENE l installatore e l utilizzatore durante l uso dell apparecchio de vono considerare e rimediare a qualsiasi rischio connesso con l impianto Ad esempio i rischi derivanti da ingresso di corpi estranei o convogliamento di gas infiammabili o tossici ad alta temperatura SCELTA DEL LUOGO PER L INSTALLAZIONE AVVERTENZE Installare l unita di recupero calore EBF su di un soffitto solido non soggetto a vibrazioni in grado di sopportare il peso della macchina consigliata l installazione antivibranti in gomma particolare fig 4 Le aperture di ripresa e di mandata dell aria non devono essere ostruite l aria deve poter circolare liberamente Non installare l unit vicino a fonti di calore vapore o gas infiammabili Installare l unita di recupero calore EBF vicino ad una presa elettrica o con un collegamento dedicato Installare la macchina dove sia facile realizzare lo scarico della condensa Controllare periodicamente il funzionamento della macchina e lasciare attorno ad essa gli spazi necessari Installare l unita di recupero calore EBF in modo che il filtro sia facilmente ac cessibile Non installare la macchina in ambienti in cui siano presenti sostanze acide ag gressive o corrosive rischio di danneggiamento irreparabile dell unit e dei suoi accessori Scegliere un luo
26. pi estranei a bloccare la rotazione della ventola WHAT TO DO IF If the motor does not turn the power supply is not connected the thermostat switches are not in the correct operating position there could be foreign matter jamming the fan wheels C un calo delle prestazioni dopo un periodo di funzionamento Controllare che il filtro ed il recuperatore a piastre non siano sporchi non vi sia presenza di ostruzioni nei canali If there is a drop in performance after a period of operation the filter and plate type recovery unit could be dirty the ducts could be obstructed Forti vibrazioni Controllare che che la girante non sia squilibrata a causa di usura o di depositi di polvere non vi sia strisciamento delle girante sulla coclea dovuto a deformazioni non vi sia presenza di ostruzioni nei canali SMANTELLAMENTO DELL APPARECCHIO Questo apparecchio costruito per durare molti anni In caso di smantellamento richiedete l intervento di personale qualificato affinch il lavoro venga svolto nella massima sicurezza Ricordate sempre che la prima operazione da svolgere prima dello smantellamento dell apparecchio di scollegarlo in modo definitivo dalla rete elettrica Questo apparecchio costruito utilizzando materiali riciclabili rame alluminio ottone plastica assemblati mediante viti e incastri in modo da facilitare le opera zioni di separazione delle parti Rivolgetevi ad una ditta special
27. reakage To make the unit inoperable disconnect it totally from the electricity supply It is unsafe to alter or try to alter the characteristics of this product Any tampering or alteration of any kind whatsoever invalidates the warranty In the event of malfunction or failure do not try to repair the unit yourself contact a qualified technician Repairs carried out by incompetent persons could cause damage or accidents Always keep the unit clean In particular periodically clean the air filter if installed at least once a month FAILURE TO COMPLY WITH THE INSTALLATION INSTRUCTIONS GIVEN IN THIS GUIDE RELIEVES THE PRODUCER FROM ALL AND ANY LIABILITY IN CORRECT INSTALLATION COULD CAUSE MALFUNCTIONING OR FAILURE OF THE UNIT IT COULD ALSO REPRESENT A HAZARD FOR THE USER mekar it Manuale di installazione uso e manutenzione Installation and maintenance manual IDENTIFICAZIONE DELL APPARECCHIO recuperatori di calore sono dotati di una targhetta di identificazione che riporta Marchiatura CE Modello Portata aria nominale in m h Corrente assorbita nominale in A Potenza disponibile in W Data di produzione Potenza termica recupero in W Numero lotto Pressione statica in Pa TRASPORTO RICEVIMENTO MOVIMENTAZIONE L apparecchio viene spedito racchiuso in un apposito imballo di protezione che deve essere mantenuto integro fino al posizionamento n
28. se and disposal of the packaging and of the products used for cleaning and maintenance of the appliance Avoid touching moving appliance parts Check that the various parts are intact before switching on the appliance Do not proceed with maintenance or cleaning without having first cut off the power supply to the appliance Damaged or worn parts must be maintained or replaced solely by specialised personnel When disposing of the appliance abide by current applicable regulations and legislation NOTE when using the appliance the installer and user must consider and remedy any risk connected with the system For example risks due to the ingress of foreign matter or the conveying of inflammable or toxic gases at high temperature SELECTION OF INSTALLATION LOCATION RECOMMENDATIONS The unit must be installed in a solid and vibration free ceiling able to support the weight The installation of rubber vibration isolation mountings is recommended part Fig 4 There must be no obstruction of the air flow into and out of the unit the air must be able to circulate freely Do not install the unit near sources of heat steam or inflammable gases Install the unit near an electric socket or connect it directly to the power supply The selected place should allow easy drainage of the condensate Periodically check appliance operation and leave sufficient space around the appliance Install the unit so that the filt
29. ticamente Thermally acoustically insulated panelling 6 MEKAR mekar it Manuale di installazione uso e manutenzione Installation and maintenance manual DATI TECNICI GENERALI GENERAL TECHNICAL DATA MOD 01 02 03 04 05 06 Portata aria nominale Rated air flow m3 h 500 750 1 250 2 000 2 500 3 000 Pressione statica massima Max static pressure Pa 125 200 100 150 100 105 Livello di pressione sonora Sound pressure level dB A 48 4 47 9 47 2 51 3 53 4 60 0 riferito secondo la norma ISO 3741 nella posizione di uscita aria di rinnovo con batteria di post riscaldamento according to ISO 3741 referring to the fresh air outlet site with re heating coil Recupero termico Heat recovery Efficienza recupero Recovery efficiency 46 46 46 46 49 49 Potenza termica recupero Heat recovery capacity kw 2 1 3 2 5 2 8 3 11 0 14 0 Temperatura uscita aria Air outlet temperature C 6 5 6 6 6 4 6 4 7 2 7 2 Prestazioni con temperatura aria di rinnovo di 5 C e temperatura aria espulsione di 20 C Performance with fresh air temperature 5 C and expelled air temperature 20 C Ventilatore Fan Poli Poles n 2 2 4 4 4 4 Numero velocit ventilatore Number of fan speed n 1 1 3 3 3 3 Grado di protezione Protection rating IP IP 32 IP 32 IP 44 IP 55 IP 55 IP 10 Classe d isolamento Insulation class B F F F F F Ba
30. ts must be sized in relation to the system and the airflow characteristics of the fans of the unit An incorrect calculation of duct size could cause malfunction e g loss of pressure of the appliance or the activation of any safety devices in stalled in the system To prevent the transmission of any vibration of the appliance to the surroundings it is advisable to use vibration isolation joints between the fan outlets and the ducts Electrical continuity between duct and appliance must also be guaranteed by me ans of an earth wire To prevent the formation of condensation and reduce the noise level it is advisable to use lagged ducts WATER CONNECTIONS The water pipes must be connected in a workmanlike manner by specialised in stallers otherwise proper operation of the system could be jeopardised and irre parable damage caused to the appliance CONDENSATE DRAINAGE The condensate collecting tray of the heat recovery units is in galvanised plate and has a drain pipe of 20 mm To check and maintain this tray remove the screws from the lower part of the appliance Fig 05 Per una buona installazione ed un corretto funzionamento si consiglia la previsione di un sifone per prevenire l insorgere di cattivi odori completo di tappo per la pulizia nella parte bassa nel caso non sia possibile deve permettere una facile manutenzione e pulizia il tubo per lo scarico della condensa con pendenza verso l esterno ed il
31. tteria post riscaldamento Water re heat coil Attacchi Fittings 1 2 1 2 1 2 1 2 3 4 3 4 Resa termica Heating capacity Ww 4 990 8 040 12 100 19 000 22 200 27 700 Ranghi Rows n 3 3 3 3 3 3 Temperatura uscita aria Air outlet temperature ES 45 9 44 7 42 4 39 0 39 6 39 5 Perdita di carico lato aria Air side pressure loss Pa 20 23 32 50 47 47 Perdita di carico lato acqua Water side pressure loss kPa 11 13 14 13 19 16 Portata aria nominale Rated air flow m3 h 375 625 1 000 1 750 2 000 2 500 Condizioni per la batteria ad acqua di post riscaldamento temperatura acqua 70 60 C temperatura aria ingresso 8 C portata aria nominale Water re heat coil conditions water temperature 70 60 C air inlet temperature 8 C rated air flow Resistenza elettrica post riscaldamento He heat electric heater Tensione nominale Nominal current Ww 1 400 2 000 2 700 3 200 3 200 3 700 3 700 4 200 3 700 4 200 4 700 5 700 Voltaggio Voltage V 230 230 230 230 230 230 Fase Phase n 1 1 1 1 1 1 Assorbimento Input A 6 1 8 7 11 7 13 9 13 9 16 1 16 1 18 3 16 1 18 3 20 4 24 8 Temperatura uscita aria Air outlet temperature C 17 1 21 0 19 7 21 8 16 3 17 6 14 0 14 9 12 8 13 4 13 1 14 2 Condizioni per la resistenza elettrica temperatura aria ingresso 8 C portata aria nominale Re heat electric heater conditions inlet air temperature 8 C rate
32. uitably adapted CONTROLS AT FIRST TIME OF STARTING Check that the unit is correctly fixed to the ceiling and also any supplementary supporting bars Check the precise position of the panels Ensure that there is no air in any water re heat coil if there is bleed through the air valve Check that the unit earth wire has been connected Check that the earth wires for the electrical parts have been connected Ensure that the pipes for any water re heat coils have been suitably lagged Ensure that the ducts are connected to the unit MAINTENANCE CAUTION Before carrying out any cleaning or maintenance work disconnect the unit from the mains electricity supply Under no circumstances use water for cleaning It is the user s duty to have all maintenance operations carried out periodically ONLY qualified personnel may carry out maintenance If parts have to be disassembled protect hands with work gloves MONTHLY MAINTENANCE A Cleaning the air filter 1 Loosen the 2 fixing screws and remove the filter holder plate 2 Take out the filter 3 Aspirare il filtro con un aspirapolvere 4 Lavare il filtro con acqua e detergente no solventi 5 Lasciare asciugare il filtro in un posto arieggiato 12 MEKAR AIR HANDLING UNITS 3 Clean the filter with a vacuum cleaner 4 Wash the filter with water and detergent no solvents 5 Leave the filter to dry in a ventilated place

Download Pdf Manuals

image

Related Search

Related Contents

Graco Inc. 800-233 Pressure Washer User Manual  Mode d`emploi Chariot E-Z-Go GT-500  Intel S2400GP2    Mode d`emploi METTLER TOLEDO Terminal de pesage IND449  Instruction Manual Albatros Tournament Management System  

Copyright © All rights reserved.
Failed to retrieve file