T1/E1 Ethernet Network Extender Kit (Manual)
Contents
1. 8 724 746 5500 blackbox com Chapter 2 Overview 2 2 Features e Support inverse multiplexing for four or eight E1 T1 lines e LRO304A KIT supports maximum bandwidth up to 7 936 6 144 Mbps for Ethernet e LRO308A KIT supports maximum bandwidth up to 15 872 12 288 Mbps for Ethernet e Auto backup and recovery for Ethernet bridge connection e Comply with ITU T G 703 G 823 G 824 e 4 or 8 RJ 48 connectors for E1 T1 100 120 ohm impedance e Ethernet Bridge for 10 100 BASE T interface e Comply with IEEE 802 3 and 802 3u e 2 RJ 45 connectors for Ethernet Interface e Autosensing autonegotiating for 10BASE T 100BASE TX and half full duplex e Ethernet Auto MDI MDI X for auto Tx Rx swap so you don t need a crossover cable e LRO304A KIT 10 LED indicators for status monitoring e LRO308A KIT 18 LED indicators for status monitoring e RS 232 console port for configurations and settings 2 3 What s Included Your package should include the following items If anything is missing or damaged please contact Black Box Technical Support at 724 746 5500 LRO304A KIT e 2 LRO304A 4 Port T1 E1 Network Extenders e 2 Power cords e 2 Ethernet CAT5 cables e 2 RS 232 console cables e This user s manual on CD ROM LRO308A KIT e 2 LRO308A 8 Port T1 El Network Extenders e 2 Power cords e 2 Ethernet CAT5 cables e 2 RS 232 console cables e This user s manual on CD ROM Page 9 4 Port and 8 Port T1 E1 Ethernet Ne2. 8 Port T1 E1 Ethernet Network Extender Kits The options for each item are shown in Figure 4 3 E1 T1 Settings System Clock Source Subscriber Interface Frame Mode LIU Line Code 56k 64k Channel LIU Impedance Loopback Testing Ethernet Settings Activate the Configurations Status UP DOWN move cursor SPACE select ENTER confirm Q q quit Figure 4 3 Options for each item LRO304A KIT Press the enter at the item Loopback Testing to enable the E1 T1 loopback testing and the status will show the loopback status To end the loopback testing press the Q or q key to stop and go back to normal E1 T1 connections Page 14 724 746 5500 blackbox com NOTES Page 15 Black Box Tech Support FREE Live 24 7 Tech support the way it should be A i gh E d Great tech support is just 30 seconds away at 724 746 5500 or blackbox com lt BLACK BOX About Black Box Black Box Network Services is your source and extensive range of networking and infrastructure products You ll find everything from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by free live 24 7 Tech support available in 30 seconds or less Copyright 2011 All rights reserved LRO304A KIT version 2 724 746 5500 blackbox com
3. LRO304A KIT lt SBLACK BOX LRO308A KIT NETWORK SERVICES Extend Ethernet with four or eight T1 E1 connections over OP Bridges 10BASE T 100BASE TX Ethernet interface 4 Port unit supports maximum bandwidth of 6 14 7 936 Mbps on El 8 Port unit supports maximum bandwidth 15 872 Mbps on El Supports Ethernet Auto MDI X function so no needed Provides auto backup and recovery for Ether BL B 724 746 5500 der t Network Exten CONSOLE 4 Port T1 E1 Etherne LR0304A KIT CET Eu r A E veer 100M 100M 9600 N 8 1 e mal 90 BOX POWER LANI ASE der t Network Exten oNSOLE 4 Port T1 E1 Etherne LRO304A KIT e AC o oom 100M 2 A omnee 1 power Lan LAN Customer Order toll free in the U S Call 877 877 BBOX outside U S call 724 746 5500 e Support FREE technical support 24 hours a day 7 days a week Call 724 746 5500 or fax 724 746 0746 e Inf ti Mailing address Black Box Corporation 1000 Park Drive Lawrence PA 15055 1018 e niormation Web site www blackbox com E mail info blackbox com 4 Port and 8 Port T1 E1 Ethernet Network Extender Kits Trademarks Used in this Manual Black Box and the Double Diamond logo are registered trademarks of BB Technologies Inc AT amp T is a registered trademark of AT amp T Intellectual Property Il LP Microsoft and Windows are registered trademarks of Microsoft Corporation Any other trademarks mentioned in this manual are acknowledged to be the pro
4. T amp T TR 62411 E1 ITU T G 823 Standards IEEE 802 3 IEEE 802 3u EMI emissions FCC Class A CE Mark Line Code T1 AMI B8ZS El AMI HDB3 Line Impedance T1 100 ohm E1 75 120 ohm Line Rate T1 1 544 Mbps 32 ppm E1 2 048 Mbps 50 ppm Line Interface T1 AT amp T TR 62411 ITU T Rec G 703 G 704 ANSI T1 403 G 824 E1 ITU T G 703 G 704 G 706 G 732 G 823 LAN Interface Auto detection for 1OBASE T 100BASE TX full half duplex and Auto MDI MDI X Connectors LRO304A KIT T1 E1 4 RJ 48 Ethernet 2 RJ 45 RS 232 console port 1 DB9 F LRO308A KIT T1 E1 8 RJ 48 Ethernet 2 RJ 45 RS 232 console port 1 DB9 F Indicators LRO304A KIT 10 LEDs 1 Power 1 Test T1 E1 1 4 LAN1 LANZ 2 10 100M LRO308A KIT 18 LEDs 1 Power 1 Test T1 E1 1 8 LAN1 LAN2 LAN3 LANA 4 10 100M Power Input 110 220 VAC 50 60 Hz Temperature Tolerance Operating 32 to 122 F 0 to 50 C Humidity Tolerance 5 to 95 noncondensing Size 1 7 H x 10 2 W x 5 9 D 4 4 x 26 x 15 cm Page 7 4 Port and 8 Port T1 E1 Ethernet Network Extender Kits 2 Overview 2 1 Introduction The LRO304A KIT includes two 4 port T1 E1 Ethernet Network Extenders that inversely multiplex data from an Ethernet 10BASE T 100BASE TX interface into four T1 E1 lines then multiplexes back from four T1 E1 lines to Ethernet The LRO304A KIT provides an Ethernet bridge connection through four T1 E1 lines at a maximum b
5. andwidth of 7 936 Mbps for E1 and 6 144 Mbps for T1 It supports T1 E1 framed modes with different line codes plus it features T1 E1 loopback The LRO308A KIT includes two 8 port T1 E1 Ethernet Network Extenders that inversely multiplex data from an Ethernet 10BASE T 100BASE TX interface into eight T1 E1 lines then multiplexes back from eight T1 E1 lines to Ethernet The LRO308A KIT provides an Ethernet bridge connection through eight T1 E1 lines at a maximum bandwidth of 15 872 Mbps for E1 and 12 288 Mbps for T1 Both kits automatically maintain and back up a point to point Ethernet bridge connection when an T1 E1 line disconnects This disconnect causes individual T1 E1 signal loss and the LED turns OFF The extenders still maintain the Ethernet connection via the rest of T1 E1 connections and they automatically recover the Ethernet bridge connection when any T1 E1 is reconnected The Ethernet interface autonegotiates for 10BASE T 100 BASE TX and half full duplex You can manually configure the interface and monitor the connection status via a console port LRO304A KIT and LRO308A KIT also feature an Auto MDI MDI X function to support auto Tx Rx swap These extenders provide a cost effective symmetrical broadband Ethernet solution over T1 E1 transmission network Transmission Network AxE1 T1 E1 T1 4xE1 T1 Customer Interface Trunk Interface Customer Interface Figure 2 1 Typical appllication for the LRO304A KIT Page
6. dio Interference Regulation of Industry Canada Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la classe A prescrites dans le Reglement sur le brouillage radio lectrique publi par Industrie Canada Page 3 4 Port and 8 Port T1 E1 Ethernet Network Extender Kits Normas Oficiales Mexicanas NOM Electrical Safety Statement INSTRUCCIONES DE SEGURIDAD 1 2 3 A 5 oN OD so 10 11 12 13 14 15 16 Todas las instrucciones de seguridad y operaci n deber n ser le das antes de que el aparato el ctrico sea operado Las instrucciones de seguridad y operaci n deber n ser guardadas para referencia futura Todas las advertencias en el aparato el ctrico y en sus instrucciones de operaci n deben ser respetadas Todas las instrucciones de operaci n y uso deben ser seguidas El aparato el ctrico no deber ser usado cerca del agua por ejemplo cerca de la tina de ba o lavabo s tano mojado o cerca de una alberca etc El aparato el ctrico debe ser usado nicamente con carritos o pedestales que sean recomendados por el fabricante El aparato el ctrico debe ser montado a la pared o al techo s lo como sea recomendado por el fabricante Servicio El usuario no debe intentar dar servicio al equipo el ctrico m s all a lo descrito en las instrucciones de operaci n Todo otro servicio deber ser re
7. ferido a personal de servicio calificado El aparato el ctrico debe ser situado de tal manera que su posici n no interfiera su uso La colocaci n del aparato el ctrico sobre una cama sof alfombra o superficie similar puede bloquea la ventilaci n no se debe colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilaci n El equipo el ctrico deber ser situado fuera del alcance de fuentes de calor como radiadores registros de calor estufas u otros aparatos incluyendo amplificadores que producen calor El aparato el ctrico deber ser connectado a una fuente de poder s lo del tipo descrito en el instructivo de operaci n o como se indique en el aparato Precauci n debe ser tomada de tal manera que la tierra fisica y la polarizaci n del equipo no sea eliminada Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos poniendo particular atenci n a los contactos y recept culos donde salen del aparato El equipo el ctrico debe ser limpiado nicamente de acuerdo a las recomendaciones del fabricante En caso de existir una antena externa deber ser localizada lejos de las lineas de energia El cable de corriente deber ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo 17 Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u ori
8. ficios de ventilaci n 18 Servicio por personal calificado deber ser provisto cuando A El cable de poder o el contacto ha sido da ado u B Objectos han ca do o l quido ha sido derramado dentro del aparato o C El aparato ha sido expuesto a la lluvia o D El aparato parece no operar normalmente o muestra un cambio en su desempe o o E El aparato ha sido tirado o su cubierta ha sido da ada Pa ge 4 724 746 5500 blackbox com CE Statement European Community CE Electromagnetic Compatibility Directive This equipment has been tested and found to comply with the protection requirements of European Emission Standard EN55022 EN61000 3 and the Generic European Immunity Standard EN55024 EMC EN55022 2003 CISPR 2 2002 Class A 1EC61000 4 2 2001 4 KV CD 8 KV AD 1EC61000 4 3 2002 3 V m 1EC61000 4 4 2001 1 KV power line 0 5 KV signal line Page 5 4 Port and 8 Port T1 E1 Ethernet Network Extender Kits Te SPECI TEE 7 Di e EE 8 ZA MME e rie EE 8 2 2 a 9 Ee El EEN 9 2 4 LED D scriptiONS nseries i a ao dundnun tas AAN ER E A EEE dads aeae 10 2 5 Frontand Back et 10 Sl EE 11 A RS 232 CONSOlE CON EE 12 4 1 RS 232 Console CONMECUOM Setup miissen aei en ae aE Ea aE E LEE ae iaae Du asia 12 AD CONSO lE C Omoa EE 13 Page 6 724 746 5500 blackbox com Chapter 1 Specifications 1 Specifications Frame Format T1 ESF SF E1 CRC4 CAS CAS CRC4 Jitter Wander Performance T1 A
9. perty of the trademark owners We re here to help If you have any questions about your application or our products contact Black Box Tech Support at 724 746 5500 or go to blackbox com and click on Talk to Black Box You ll be live with one of our technical experts in less than 30 seconds Page 2 724 746 5500 blackbox com FCC and IC RFI Statements Federal Communications Commission and Industry Canada Radio Frequency Interference Statements This equipment generates uses and can radiate radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Ra
10. power to the AC socket 4 Turn on the power switch The LED indicators for E1 T1 connections and Ethernet should be ON 5 Set the desired E1 T1 settings and Ethernet settings from the console port and activate the configurations Refer to Chapter 4 to see how to configure your 4 Port or 8 Port T1 E1 Ethernet Extender NOTE The LRO304A KIT or LRO308A KIT extenders will execute self test routines and automatically connect with each other The LAN LED indicators will start flashing to show Ethernet data activities Page 11 4 Port and 8 Port T1 E1 Ethernet Network Extender Kits 4 RS 232 Console Configuration 4 1 RS 232 Console Connection Setup LRO304A KIT provides an RS 232C console port to monitor the OA amp M status through a VT100 terminal Follow the steps listed below to connect the console port from the extender to the terminal 1 Attach the DB9 female connector of the included RS 232 console cable to the male DB9 serial port connector on the rear panel of the extender Then attach the other end of the DB9 cable to an ASCII terminal emulator or PC COM 1 2 port For example PC runs Microsoft Windows HyperTerminal utility N At Com Port Properties Menu configure the parameters as below Baud rate 9600 Stop bits 1 Data bits 8 Parity N Flow control none 3 Press the lt ESCAPE gt key and the main menu will appear on the terminal s screen NOTE If you press the lt ESCAPE gt key and the screen of the te
11. rminal does not display the COM port might be set incorrectly Choose the correct COM port COM1 or COM2 on the computer and press the lt ESCAPE gt key again to make sure that the main menu appears on the terminal screen 4 PortT1 E1 Network Extender RS 232 Cable Baud rate 9600 Stop bits 1 Data bits 8 Parity N Flow control none VT100 102 Terminal PC COM Port Figure 4 1 Connection for console port with RS 232 terminal Page 12 724 746 5500 blackbox com Chapter 4 RS 232 Console Configuration 4 2 Console Configuration Once you log in to the console the main menu will be displayed on the screen The main menu will display the LRO304A KIT or LRO308A KIT unit s connection status and settings in three sections T1 E1 Settings Ethernet Settings and Status T1 E1 Settings System Clock Source Subscriber Interface Frame Mode LIU Line Code 56k 64k Channel LIU Impedance Loopback Testing Ethernet Settings Activate the Configurations Status UP DOWN move cursor SPACE select ENTER confirm Q q quit Figure 4 2 Main menu LRO304A KIT In the main menu use the up and down arrow keys to move the cursor up and down and use the space key to select differ ent options for each item Press enter key to confirm the selection After completing the configurations move to Activate the Configuration and press enter to activate the configurations Page 13 4 Port and
12. twork Extender Kits 2 4 LED Descriptions Table 2 1 Indicators LED Color Function POWER Green Lit when power is on TEST Yellow Lit when device is ready Blinks when device is in self test 10 100M Green Lit when Ethernet is connected at 100 Mbps Off when Ethernet is connected at 10 Mbps LAN 1 2 Green Lit when Ethernet is connected Blink when transmitting receiving data T1 E1 1 4 Green Lit when T1 E1 is connected 2 5 Front and Back Panels CONSOLE 9600 N 8 1 4 Port T1 E1 Network Extender LED Indicators RS 232 Console Port Figure 2 2 Front panel LRO304A KIT NOTE The LRO308A KIT s front panel is similar to the LRO304A KIT s but it has 18 LED indicators instead of 10 Power Input Ethernet Port E 110 220V OFF Power Switch E1 T1 RJ 48 Interface Figure 2 3 Back panel LRO304A KIT NOTE The LRO308A KIT s back panel is similar to the LRO304A KIT s but it has eight E1 T1 RJ 48 interface connectors instead of four Page 10 724 746 5500 blackbox com Chapter 3 Installation 3 Installation 1 Connect 4 or 8 T1 E1 Trunk Lines to RJ 48 connectors on the back panel Figure 3 1 shows the RJ 48 connector s pin assignments Pin 4 and Pin 5 to input of demarc Pin 1 and Pin 2 to output of demarc Figure 3 1 RJ 48 port s pin assignment 2 Connect CAT5 Ethernet cable to the RJ 45 connectors on the back panel 3 Connect the 100 240 VAC
Download Pdf Manuals
Related Search