Home

BL100-150 Tabloid Template - Troy-Bilt

image

Contents

1. Blade Retainer Cutting Blade WARNING If the cutting blade is off center the unit will vibrate and the blade may fly off causing possible serious personal injury Make sure that the cutting blade is centered on the pilot step and sitting flat against the output shaft bushing Fig 14 3 Align the shaft bushing hole with the locking rod slot and insert the locking rod into the bushing hole Fig 10 4 Put the blade retainer and nut on the output shaft Make sure that the blade is installed correctly 5 Tighten nut counterclockwise against the blade while holding the locking rod e f using a torque wrench and a 13 mm socket tighten to 325 335 inelb 27 28 ft elb 37 38 Nem e Without a torque wrench use a 13 mm closed end or socket wrench turning the nut until the blade retainer is snug against the shaft bushing Make sure that the blade is installed correctly then rotate the nut an additional 1 4 to 1 2 turn counterclockwise Fig 15 6 Remove the locking rod from the locking rod slot Output Shaft Bushing Locking Rod 1 4 1 2 turn Counterclockwise Fig 15 WARNING To avoid serious personal injury or damage to the unit do not start or operate this unit with the locking rod in the locking rod slot WARNING Do not sharpen the cutting blade Sharpening the blade can cause the blade tip to break off while in use This can result in severe personal injury Replace the blade
2. REMOVE THE CUTTING BLADE AND INSTALL THE CUTTING ATTACHMENT Remove the Cutting Blade 1 Align the shaft bushing hole with the locking rod slot and insert the locking rod into the bushing hole Fig 10 2 Hold the locking rod in place by grasping it next to the boom of the unit Fig 11 3 While holding the locking rod loosen the nut on the blade by turning it clockwise with a 13 mm closed end or socket wrench Fig 16 4 Remove the nut blade retainer and blade Store the nut and blade together for future use in a secure place Store out of children s reach Install the Cutting Attachment 1 Align the shaft bushing hole with the locking rod slot and insert the locking rod into the shaft bushing hole Fig 10 Place the blade retainer on the output shaft with the flat surface against the output shaft bushing Fig 17 Screw the cutting attachment counterclockwise onto the output shaft Tighten securely NOTE The blade retainer must be installed on the output shaft in the position shown for the cutting attachment to work correctly 2 Remove the locking rod 3 Install the cutting attachment shield Refer to Remove and Install the Cutting Attachment Shield Blade Retainer Te Output Shaft Bushing Locking Rod WARNING To avoid serious personal injury the cutting attachment shield MUST be in place at all times while operating the unit as a trimmer OIL AND FUEL INFORMATION OIL
3. OTROV BILT 1222 5c Operator s Manual a gt FASTGUIDE Removing Unit From Carton Assemble The Unit Electric Starter or Starter Rope Power Start Bit Optional THESE OPTIONAL ACCESSORIES ARE SOLD SEPARATELY Fuel Cap This unit has an alternate starting method that many find easier to use than pulling a rope Please contact a local retailer or call r 1 800 828 5500 for more information lt b Information may also be found at On Off Switch D www troybilt com amp wee Control Qa Remove all contents from Remove cap from end of Place the J handle between the top and middle clamps the carton lower boom Push cutting slide the 4 screws through the clamps and place the attachment add on into assembly onto the bottom clamp Start the screws J Handle lt coupler Turn coupler knob then ensure the arrow white line on the decal touches clockwise to tighten the clamp assembly Position the J handle to the location that provides the best grip then tighten the screws evenly until the J handle is secure Ez Link m Assemble The Unit Starting The Unit ASSEMBLY TOOLS REQUIRED Choke Lever e Phillips screwdriver Need Help Call 1 800 828 5500 1 Gallon DIDN T START Mix thoroughly in separate Place unit on a level surface Press primer bulb 10 times Move choke lever to fuel can Fill fuel tank or until fuel is visible Position 1 Repeat these instructions o 2 cycle IF engine
4. corrosion and minimize the formation of gum deposits It is recommended to use our 2 cycle oil with this unit If unavailable use a good 2 cycle oil designed for air cooled engines along with a fuel additive such as STA BIL Gas Stabilizer or an equivalent Add 0 8 oz 23 ml of fuel additive per gallon of fuel according to the instructions on the container NEVER add fuel additives directly to the unit s fuel tank Thoroughly mix the proper ratio of 2 cycle engine oil with unleaded fuel in a separate fuel can Use a 40 1 fuel oil ratio Do not mix them directly in the engine fuel tank See the table for specific gas and oil mixing ratios NOTE One gallon 3 8 liters of unleaded fuel mixed with one 3 2 oz 95 ml bottle of 2 cycle oil makes a 40 1 fuel oil ratio WARNING Gasoline is extremely flammable Ignited vapors may explode Always stop the engine and allow it to cool before filling the fuel tank Do not smoke while filling the tank Keep sparks and open flames at a distance from the area WARNING Remove fuel cap slowly to avoid injury from fuel spray Never operate the unit without the fuel cap securely in place WARNING Add fuel in a clean level and well ventilated outdoor area Wipe up any spilled fuel immediately Avoid creating a source of ignition for spilled fuel Do not start the engine until fuel vapors dissipate NOTE Dispose of the old fuel oil mix in accordance to federal state and local regulati
5. 12 3 13 5 Nem Do not over tighten CLEANING AND STORAGE CLEANING WARNING To avoid serious personal injury always turn the unit off and allow it to cool before you clean or service it Use a small brush to clean off the outside of the unit Do not use strong detergents Household cleaners that contain aromatic oils such as pine and lemon and solvents such as kerosene can damage plastic housing or handle Wipe off any moisture with a soft cloth STORAGE e Never store a fueled unit where fumes may reach an open flame or spark e Allow the engine to cool before storing e Store the unit locked up to prevent unauthorized use or damage e Store the unit in a dry well ventilated area e Store the unit out of the reach of children Short Term Storage 1 2 weeks 1 zo the unit in a horizontal position If this is not possible store the unit vertically with the engine at the top Long term Storage 1 Remove the fuel cap tip the unit and drain the fuel into an approved container NOTE Do not use gasoline that has been stored for more than 30 days Dispose of old gasoline in accordance with federal state and local regulations 2 Start the engine and allow it to run until it stalls This ensures that all fuel has been drained from the carburetor 3 Allow the engine to cool Remove the spark plug and put 5 drops of any high quality motor oil or 2 cycle oil into the cylinder Pull the starter rope slowly to distribute the o
6. ALERTA DE SEGURIDAD Indica peligro advertencia o precauci n Debe prestar atenci n para evitar sufrir graves lesiones personales Puede ser utilizado junto con otros SIMBOLO SIGNIFICADO s mbolos o figuras e SIMBOLO DE ALERTA DE SEGURIDAD IIndica peligro advertencia o precauci n Puede ser utilizado junto con otros s mbolos PELIGRO El no obedecer una advertencia de seguridad puede conducir a que usted u o figuras otras personas sufran graves lesiones Siga siempre las precauciones de seguridad para reducir el riesgo de incendio descarga el ctrica y lesiones personales LEA EL MANUAL DEL OPERADOR ADVERTENCIA Lea el manual del operador y siga todas las advertencias e instrucciones de seguridad De no hacerlo el operador y o los espectadores pueden ADVERTENCIA El no seguir una advertencia de seguridad puede conducir a que usted u otras personas sufran lesiones Siga siempre las precauciones de seguridad para reducir el riesgo de incendio descarga el ctrica y lesiones personales sufrir graves lesiones USE PROTECCION OCULAR Y AUDITIVA ADVERTENCIA Los objetos arrojados por la unidad y el ruido fuerte pueden causar graves lesiones oculares y p rdida auditiva Utilice protecci n ocular que cumpla con las normas ANSI Z87 1 1989 y protecci n auditiva cuando opere esta unidad Use una careta completa cuando la necesite PRECAUCI N El no seguir una advertencia de seguridad puede conducir a da o patrimonial O a que usted u
7. Always follow the safety precautions to reduce the risk of fire electric shock and personal injury WARNING Failure to obey a safety warning can result in injury to yourself and others Always follow the safety precautions to reduce the risk of fire electric shock and personal injury CAUTION Failure to obey a safety warning may result in property damage or personal injury to yourself or to others Always follow the safety precautions to reduce the risk of fire electric shock and personal injury NOTE Advises of information or instructions vital to the operation or maintenance of the equipment READ THE OPERATOR S MANUAL AND FOLLOW ALL WARNINGS AND SAFETY INSTRUCTIONS FAILURE TO DO SO CAN RESULT IN SERIOUS INJURY TO THE OPERATOR AND OR BYSTANDERS FOR QUESTIONS CALL 1 800 828 5500 IN U S OR 1 800 668 1238 IN CANADA e IMPORTANT SAFETY INSTRUCTIONS e CALIFORNIA PROPOSITION 65 WARNING Engine exhaust some of its constituents and certain finished components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling READ ALL INSTRUCTIONS BEFORE OPERATING WARNING When using the unit all safety rules must be followed Please read these instructions before operating the unit in order to ensure the safety of the operator and any bystanders Please keep these instructions for later use e Read the instructions carefully Be familiar
8. Verifique que la cuchilla est bien instalada luego gire la tuerca 1 4 a 1 2 vuelta m s en sentido antihorario Fig 15 6 Saque la varilla de cierre de la ranura de la varilla de cierre Estribo de gu a 1 4 1 2 de vuelta en sentido antihorario Fig 15 ADVERTENCIA No afile la cuchilla de corte Afilar la cuchilla puede causar que la punta se desprenda durante el uso Esto puede causar graves lesiones personales Cambie la cuchilla Remoci n de la cuchilla de corte 1 Alinee el orificio del buje del eje con la ranura de la varilla de cierre e inserte la varilla de cierre en el orificio del buje Fig 10 2 Sostenga la varilla de cierre en su lugar junto al brazo de la unidad Fig 11 3 Mientras sostiene la varilla de cierre afloje la tuerca de la cuchilla gir ndola en sentido horario con una llave de casquillo o de boca cerrada de 13 mm Fig 16 4 Saque la tuerca el ret n de la cuchilla y la cuchilla Guarde la tuerca y la cuchilla juntas en un lugar seguro para su uso futuro Guarde fuera del alcance de los ni os Instalaci n del accesorio de corte 5 Alinee el orificio del buje del eje con la ranura de la varilla de cierre e inserte la varilla de cierre en el orificio del buje del eje Fig 10 Coloque el ret n de la cuchilla en el eje de salida con la superficie plana contra el buje del eje de salida seg n se ilustra en la Fig 17 Enrosque el accesorio de corte en sentido antihorario en el eje
9. dise ada para utilizarse de forma opcional con un arrancador el ctrico o con un accesorio de arranque Power Start Bit los cuales se venden por separado Si decide arrancar la unidad utilizando uno de estos sistemas de arranque o tiene alguna pregunta comun quese con su distribuidor local o llame al 1 800 828 5500 en EE UU 1 800 668 1238 en Canad para m s informaci n as como la forma de comprarlo Tambi n puede ir a www troybilt com o www troybilt ca La l nea se retorci al reponerla Desarme y rebobine la l nea Oprima el bot n de tope y tire de la l nea hasta sacar Nelhay suficients inealexpuesta 102 mm 4 pulg de linea fuera del accesorio de corte LA LINEA DE CORTE AVANZA SIN CONTROL El cabezal de corte tiene aceite Limpie el aditamento de corte SI NECESITA ASISTENCIA ADICIONAL COMUN QUESE CON SU PROVEEDOR DE SERVICIO AUTORIZADO Electric Start Feature Fig 37 4 07131070 01 234 Tipo de Motor irer 246 os ed ae pas ia o ied Beene Enfriado por aire de 2 ciclos Camera u a titre ees A Peed EET See 1 10 pulg 2 8 cm Desplazamientos chi aora 27 cc RPM de OperaciO vespa ri doi ds dia aa 6 800 r p m RPM demarcha lenta ius ca ia a odds 2 800 3 400 r p m Separaci n de la buj a de encendido 0 cee eee 0 025 pulg 0 635 mm LUDTICACI N oca za AA anna Mezcla de combustible y aceite Proporci n de combustible aceite oooooocococconrnnn teens 40 1 C
10. tome los extremos y hale con firmeza para soltar la l nea de las ranuras de retenci n de la bobina Sostenga el carrete interior en su lugar e instale el bot n de tope gir ndolo en sentido horario Ajuste bien INSTRUCCIONES DE MANTENIMIENTO Y REPARACI N MANTENIMIENTO DEL FILTRO DE AIRE ADVERTENCIA Para evitar graves lesiones personales apague siempre su recortador y espere que se enfr e antes de limpiarlo o realizar todo tipo de mantenimiento Nettoyage du Filtre a Aire Bastidor No mantener debidamente su filtro de del filtro aire puede resultar en funcionamiento Filtro de aire de aire inadecuado o puede causar da o Cubierta del filtro de aire permanente a su motor 1 Abra la tapa del filtro de aire Tornillo de desenroscando el tornillo correspondiente Fig 34 2 Saque el filtro de aire y la pantalla que est detr s del mismo Fig 34 3 Lave el filtro con detergente y agua Enjuague bien el filtro y d jelo secar 4 Aplique suficiente aceite limpio de Ganchos A motor SAE 30 para recubrir Orificio del ligeramente el filtro tornillo de 5 Exprima el filtro para esparcir y la tapa eliminar el exceso de aceite 6 Reemplace el filtro de aire y la pantalla que est detr s del mismo Fig 34 NOTA Si opera la unidad sin el filtro de aire ANULARA la garant a 7 Vuelva a ponerle la tapa al filtro de aire Inserte los ganchos de la caja del filtro de aire en las ranuras de
11. 10 Continue squeezing the throttle control move the choke lever to Position 3 Fig 19 and run the unit for an additional 60 seconds The unit may be used during this time NOTE Unit is properly warmed up when engine accelerates without hesitation IF the engine hesitates return the choke lever to Position 2 Fig 19 and continue warm up IF the engine does not start go back to step 3 IF the engine fails to start after 2 attempts place the choke lever in Position 3 and squeeze the throttle control Press and hold the electric starter or drill ON I button for 2 second intervals until the unit starts IF WARM If the engine is already warm start the unit with the blue choker lever in Position 2 After the unit starts move the blue choker lever to Position 3 STOPPING INSTRUCTIONS 1 Release the throttle control and allow the engine to cool down by idling 2 Press and hold the On Off Control switch in the OFF O position until the unit comes to a complete stop Fig 19 Fig 18 Choke Lever Primer Bulb Starter Rope 4 OPERATING INSTRUCTIONS MAINTENANCE AND REPAIR INSTRUCTIONS HOLDING THE TRIMMER WARNING Always wear eye hearing foot and body protection to reduce the risk of injury when operating this unit Before operating the unit stand in the operating position Fig 21 Check for the following e The operator is wearing eye protection and proper clothing e With a slightly
12. 668 1238 in Canada available from an authorized service dealer The use of any unauthorized parts or accessories could lead Additional information about the unit can be found on our website at www troybilt com or to serious injury to the user or damage to the unit and void the warranty www troybilt ca vw e Keep unit clean of vegetation and other materials that may become lodged or entangled in the unit For service please call the Customer Support Department to obtain a list of authorized service dealers e To reduce fire hazard keep the engine and muffler free from grass leaves excessive grease or carbon near you Service on this unit both within and after the warranty period should only be performed by an build up authorized and approved service dealer When servicing use only identical replacement parts After use e Clean the unit with household cleaner to remove any gum buildup SPARK ARRESTOR NOTE OTHER SAFETY WARNINGS NOTE For users on U S Forest Land and in the states of California Maine Oregon and Washington ae deg All U S Forest Land and the state of California Public Resources Codes 4442 and 4443 Oregon and Never store a fueled unit inside a building where fumes may reach an open flame oF Spark Washington require by law that certain internal combustion engines operated on forest brush and or grass Allow the engine to cool before storing or transporting Be sure to secure the unit while transporting covered areas b
13. INSTALACI N Y AJUSTE DE LA MANIJA EN J 1 Coloque la manija en J entre la abrazadera superior y la abrazadera media Fig 1 Tornillos 4 a 2 Mientras sostiene las tres piezas juntas instale los cuatro 4 tornillos a trav s de la abrazadera superior en la abrazadera media NOTA Los orificios de la abrazadera superior y Abrazadera S TER I r A 2 x Manija media se alinear n s lo cuando se Br ensamble en forma correcta S Z m a Abrazadera 3 Coloque las abrazaderas y la manija en J AN madia N por encima del bastidor del eje y sobre la Ne abrazadera inferior 4 Sostenga cada tuerca hexagonal en el hueco de la abrazadera inferior con un dedo Comience a colocar los tornillos con un destornillador Phillips grande No los apriete hasta ajustar la manija Tuercas 4 Fig 1 5 Deslice la manija en J hacia dentro o hacia fuera hasta que la flecha o l nea blanca de la calcoman a toque el ensamble de abrazaderas Fig 2 6 Mientras sostiene la unidad en posici n de operaci n Fig 2 coloque la manija en J en la posici n que le brinde el mejor agarre 7 Ajuste los tornillos de la abrazadera en forma pareja hasta que la manija en J est firme a a US Fig 2 OPERACION DEL SISTEMA EZ LINK El sistema EZ Link le permite el uso de estos accesorios optativos Meh IWM Recortador soi a a AA ee AF720 Recortador de setos ar 00 00 a0 8 un dan ann
14. INSTRUCCIONES DE ENSAMBLE IInstalacion de la cuchilla de corte ADVERTENCIA Para evitar graves lesiones personales el protector accesorio de corte DEBE estar instalado en todo momento cuando use la unidad como recortador de c sped 1 Coloque la cuchilla de corte en el buje del eje de Tuerca salida Fig 13 ADVERTENCIA Si la cuchilla de corte no est centrada la unidad vibrar y la Ret n de la cuchilla Cuchilla de Orificio de gu a corte cuchilla puede desprenderse y salir volando lo cual puede causar graves lesiones personales 2 Verifique que la cuchilla de corte est centrada en Montaje del gt ER el estribo de gu a y quede plana contra el buje del protector N gt eje de salida Fig 14 E 3 Alinee el orificio del buje del eje con la ranura de la varilla de cierre e inserte la varilla de cierre en el Buje del eje de orificio del buje Fig 10 salida 4 Coloque el ret n de la cuchilla y la tuerca en el eje de salida Verifique que la cuchilla est bien instalada Var A 2 arilla de 5 Ajuste la tuerca en sentido antihorario contra la cierre cuchilla mientras sostiene la varilla de cierre e Si usa una llave de torsi n y un casquillo de 13 mm ajuste a 325 335 pulgelibra 27 28 pieselibra 37 38 Nem e Sino tiene una llave de torsi n use una llave de boca cerrada de 13 mm o de casquillo gire la tuerca hasta que el ret n de la cuchilla est ajustado contra el buje del eje
15. OPERATING Oil and Fuel Information os cc cc00se0s ana re sead eee a iind 4 e Wear safety glasses or goggles that are marked as meeting ANSI Z87 1 1989 standards Also wear Starting and Stopping Instructions n u un uuan aaoo cece cece eee veteeeeeeveseenees 4 ear hearing protection when operating this unit Wear a face or dust mask if the operation is dusty Long f sleeve shirts are recommended OperatingilnStructi ns ss enamigi a rn daa ne ren Eaa de e ai teca 5 an f e Wear heavy long pants boots and gloves Do not wear loose clothing jewelry short pants sandals or go Maintenance and Repair instructions sci csi dhe e ae 5 barefoot Secure hair above shoulder level Cleaning and Storage DIANA DA A DO NR A AAA A 6 e Use the unit only in daylight or good artificial light Optional ACCESSO Sos air spinga isi ie A Ge vies eee Seam nem Sie KE SE 6 e Avoid accidental starting Be in the starting position whenever pulling the starter rope The operator and Troubleshooting Chart iria n a aaa E E S 6 unit must be in a stable position while starting See Starting and Stopping Instructions DPOCIICAONS se cosa e ARE RE ad AE BOE eh BUREEE EEE E GE Hen ANE EE HR RS 6 e Use the right tool Only use this tool for the purpose intended Waranty Infonmatlon raneta nini is idas Een is 16 e Use extreme caution when reversing or pulling the unit backwards All information illustrations and specifications in this manual are based on the latest product i
16. bent right arm the operator s hand is holding the shaft grip e The operator s left arm is straight the left hand holding the J handle e The unit is at waist level e The cutting head is parallel to the ground and easily contacts the grass without the need to bend over TIPS FOR BEST TRIMMING RESULTS e Keep the cutting head parallel to the ground e Do not force the cutting head Allow the tip of the line to do the cutting especially along walls Cutting with more than the tip will reduce cutting efficiency and may overload the engine e Cut grass over 8 inches 200 mm by working from top to bottom in small increments to avoid premature line wear or engine drag e Cut from right to left whenever possible Cutting to the left improves the unit s cutting efficiency Clippings are thrown away from the operator e Slowly move the unit into and out of the cutting area at the desired height Move either in a forward backward or side to side motion Cutting shorter lengths produces the best results e Trim only when grass and weeds are dry e The life of the cutting line is dependent upon e Following the trimming techniques e What vegetation is being cut e Where vegetation is cut For example the line will wear faster when trimming against a foundation wall as opposed to trimming around a tree Some line breakage will occur from e Entanglement with foreign matter e Normal line fatigue e Attempting to cut thick stalky weeds
17. e Forcing the line into objects such as walls or fence posts DECORATIVE TRIMMING Decorative trimming is accomplished by removing all vegetation around trees posts fences etc Rotate the whole unit so that the cutting head is at a 30 angle to the ground Fig 22 USING THE CUTTING BLADE Before operating the unit with the cutting blade stand in the operating position Fig 23 Refer to Holding the Trimmer Fig 21 Fig 22 WARNING Always wear eye hearing foot body protection and the shoulder strap to reduce the risk of injury when operating this unit WARNING Do not use the cutting blade for edging or as an edger Severe personal injury to yourself or others can result Cutting Blade Operating Tips To establish a rhythmic cutting procedure e Plant feet firmly comfortably apart e Bring the engine to full throttle before entering the material to be cut At full throttle the blade has maximum cutting power and is less likely to bind stall or cause blade thrust which can result in serious personal injury to the operator or others WARNING Blade thrust may occur when the spinning blade contacts an object that it does not immediately cut Blade thrust can be violent enough to cause the unit and or operator to be propelled in any direction and possibly lose control of the unit Blade thrust can occur without warning if the blade snags stalls or binds This is more likely to occur in areas where it is difficult
18. fails to start after 2 attempts Cutting Head Shield move choke lever to position 3 and pull 1 gallon of unleaded the starter rope until engine starts gasoline NOTE Do not mix directly in IF unit still fails to start refer to operator s fuel tank manual for additional starting and troubleshooting information Starting The Unit Choke Lever Choke Lever 5X 3 5 X Crouch in starting position SQUEEZE and HOLD Pull rope 5 times Move choke lever to Pull rope 3 5 times to start Continue to squeeze Continue to squeeze throttle for ALL further Position 2 and squeeze engine Run unit for 30 60 throttle Move choke lever throttle Run unit for an steps throttle seconds to warm up to Position 3 additional 60 seconds to complete warm up Unit may be used during this time A IMPORTANT READ THE OPERATOR S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT NEED HELP CALL 1 800 828 5500 IN U S OR 1 800 668 1238 IN CANADA 769 07387 P01 11 11 TABLE OF CONTENTS RULES FOR SAFE OPERATION Service Informa Nesai e cc A a Bene 2 Rules for Safe Operation ssassn SE a aaia aoaia rr 2 e Never start or run the unit inside a closed room or building Breathing exhaust fumes can kill Only KNOW YOUR UIE za eric e har encase te de Spates a te aceon che ce ida caco Gwe E a Sahara ke 3 operate this unit in a well ventilated outdoor area Assembly Instructions 2 0 0 0 ccc cc ce cee nee eee e arrra 3 WHILE
19. forma accidental e Corte a plena regulaci n e Mueva la unidad de su izquierda a derecha hacia el N material que va a cortar Fig 24 YN Y Y Y e En el movimiento de retorno evite tocar el material que A vY y Y acaba de cortar M Y ADVERTENCIA No limpie el material con el motor en marcha ni con la cuchilla girando Para evitar graves lesiones personales apague el motor Espere que la cuchilla se detenga antes de sacar el material envuelto alrededor del eje de la cuchilla INSTRUCCIONES DE MANTENIMIENTO Y REPARACI N PROGRAMA DE MANTENIMIENTO ADVERTENCIA Para evitar lesiones personales graves nunca realice mantenimiento ni reparaciones con la unidad funcionando Realice siempre el mantenimiento y las reparaciones con la unidad fr a Desconecte el cable de la buj a de encendido para cerciorarse de que la unidad no arrancar Estos procedimientos requeridos para el mantenimiento deben ser realizados con la frecuencia indicada en la tabla Deben ser incluidos como parte de toda puesta a punto de cada temporada NOTA Algunos procedimientos de mantenimiento pueden requerir el uso de herramientas o habilidades especiales Si no est seguro acerca de estos procedimientos lleve su unidad a un establecimiento de reparaci n persona o distribuidor de servicio autorizado que arregle motores para uso fuera de la carretera NOTA El mantenimiento la sustituci n o arreglo de dispositivos para el control de emisiones y s
20. n 0 0002 eee 13 CUANDO ESTE OPERANDO Limpieza y almacenamiento o a a A 14 e Use gafas protectoras que cumplan con la norma Z87 1 1989 de ANSI y tengan la marca que lo indica Use protecci n Accesono opcional seas aa aaae EREER SENEISTEREMESERERERENE HERE SENERERERENEBEHERERERERERBHENERREENENEHEIRTERENERFOEREAERFTERE 14 para la oreja audici n cuando opere esta unidad Use m scara facial o para polvo si la operaci n produce mucho polvo Cuadro de soluci n de problemas serinin rep iai en e ara a en nn 14 Use pantalones largos fuertes botas guantes y camisa de mangas largas No use ropa holgada joyas pantalones cortos ESPECICACIO Sci id ee Denn did 14 sandalias ni est descalzo Aseg rese el cabello por encima del nivel de los hombros Garant a in 16 e El protector del accesorio de corte debe estar siempre colocado cuando se utilice la unidad como recortador No opere la unidad sin ambas l neas de corte extendidas y con la l nea adecuada instalada No extienda la l nea de corte m s all de la longitud del protector e Aseg rese de que el accesorio de corte no est en contacto con ning n objeto antes de arrancar la unidad Toda la informaci n las ilustraciones y las especificaciones contenidas en este manual se basan en la e Ajuste la manija a su tama o para proporcionar un mejor agarre informaci n m s reciente disponible en el momento de impresi n del manual Nos reservamos el e El accesorio de corte puede estar girando
21. properly mixed fuel Replace or clean the spark plug CUTTING HEAD WILL NOT ADVANCE LINE Cutting head bound with grass Cutting head out of line Inner reel bound up Cutting head dirty Line welded Stop the engine and clean cutting head Refill with new line Rewind the inner reel Clean inner reel and outer spool Disassemble remove the welded section and rewind Disassemble and rewind the line Push the bump knob and pull out line until 4 inches 102 mm of line is outside of the cutting head Line twisted when refilled Not enough line is exposed CUTTING LINE ADVANCES UNCONTROLLABLY Oil cleaner or lubricant in cutting head IF FURTHER ASSISTANCE IS REQUIRED CONTACT AN AUTHORIZED SERVICE DEALER OPTIONAL ACCESSORY ELECTRIC STARTER AND POWER START BIT FEATURES This unit is designed to be started with an optional electric starter or Power Start Bit which are sold separately If choosing to start the unit using one of these features or have questions please contact your local retailer or call 1 800 828 5500 in the U S 1 800 668 1238 in Canada for more information and purchasing You may also go to www troybilt com or www troybilt ca Clean and thoroughly dry the cutting head A Electric Start Feature Fig 37 Engine TYPE 40 rr pr ini OE Pee eee ERG DOES en Air Cooled 2 Cycle STOKE AA 1 10 in 2 8 cm Displacement asada otra SERFIETSEEHERTERRRCREIFRERRHERERFERFRETENEHERSUFL
22. to see the material being cut e Cut while swinging the upper part of your body from left to right e Always release the throttle trigger and allow the engine to return to idle speed when not cutting e When you are finished always unsnap the unit from the WARNING The blade continues to spin after the engine is turned off The coasting blade can seriously cut you if accidentally touched harness before taking off the harness e Swing the unit in the opposite direction as the blade spins which increases the cutting action e After the return swing move forward to the next area to be cut and plant your feet again e The cutting blade is designed with a second cutting edge You can use it by removing the blade turning it upside down and reinstalling it To reduce the chance of material wrapping around the blade follow these steps e Cut at full throttle e Swing the unit into material to be cut from your left to your right Fig 24 e Avoid the material just cut as you make the return swing WARNING Do not clear away any cut material with the engine running or blade turning To avoid serious personal injury turn off the engine Allow the blade to stop before removing materials wrapped around the blade shaft MAINTENANCE SCHEDULE WARNING To prevent serious injury never perform maintenance or repairs with unit running Always service and repair a cool unit Disconnect the spark plug wire to ensure
23. with the controls and proper use of the unit e Do not operate this unit when tired ill or under the influence of alcohol drugs or medication e Children and teens under the age of 15 must not use the unit except for teens guided by an adult e All guards and safety attachments must be installed properly before operating the unit e Inspect the unit before use Replace damaged parts Check for fuel leaks Make sure all fasteners are in place and secure Replace parts that are cracked chipped or damaged in any way Do not operate the unit with loose or damaged parts e Carefully inspect the area before starting the unit Remove all debris and hard or sharp objects such as glass wire etc e Be aware of the risk of injury to the head hands and feet e Clear the area of children bystanders and pets At a minimum keep all children bystanders and pets outside a 50 feet 15 m radius there still may be a risk to bystanders from thrown objects Bystanders should be encouraged to wear eye protection If approached stop the unit immediately e Squeeze the throttle control and check that it returns automatically to the idle position Make all adjustments or repairs before using unit SAFETY WARNINGS FOR GAS UNITS WARNING Gasoline is highly flammable and its vapors can explode if ignited Take the following precautions e Store fuel only in containers specifically designed and approved for the storage of such materials e Alway
24. 1 800 828 5500 en EE UU o al 1 800 668 1238 en Canada TROY BILT LLC P O Box 361131 Cleveland OH 44136 0019 16
25. AND FUEL MIXING INSTRUCTIONS Old and or improperly mixed fuel are the main reasons for the unit not running properly Be sure to use fresh clean unleaded fuel Follow the instructions carefully for the proper fuel oil mixture WARNING It has been proven that fuel containing greater than 10 ethanol will likely damage this engine and void the warranty DEFINITION OF BLENDED FUELS Today s fuels are often a blend of gasoline and oxygenates such as ethanol methanol or MTBE ether Alcohol blended fuel absorbs water As little as 1 water in the fuel can make fuel and oil separate lt forms acids when stored When using alcohol blended fuel use fresh fuel less than 30 days ola USING BLENDED FUELS If choosing to use a blended fuel or its use is unavoidable follow recommended precautions e Always use the fresh fuel mix explained in the operator s manual e Use the fuel additive STA BIL or an equivalent e Always agitate the fuel mix before fueling the unit e Drain the tank and run the engine dry before storing the unit USING FUEL ADDITIVES CAUTION For proper engine operation and maximum reliability pay strict attention to the oil and fuel mixing instructions on the 2 cycle oil container Using improperly mixed fuel can severely damage the engine UNLEADED GAS 2CYCLE OIL 1 GALLON US 3 2 FL OZ 3 8 LITERS 95 ml MIXING RATIO 40 1 The bottle of 2 cycle oil contains a fuel additive which will help inhibit
26. ENSTERERE 27 cc Operating RPM ss giai esena a lea a ae Ber ach cn ta 6 800 rpm Idle Speed RPM ies sci cece 2 34 24 mn a0 ta a ne a vee a AAA 2 800 3 400 rom Spark Plug Gap 24 cake ct es ah ceed eg deed dete wees 0 025 in 0 635 mm Lubrication 2er tinbtek dated bata ee teed ao beds Fuel Oil Mixture Fuel OlllRatio cti dice eet sg rt staan anna tte AAA E MAI A Ape ee 40 1 Fuel Tank Capcity ie iii cccrrec es ce ron pipine i korn ae eae aa PEE es 14 fl oz 897 ml Approximate Unit Weight without fuel 0 0 0 0 e eee eee 11 13 Ibs 5 5 9 kg Cutting Mechanism 0 0 ccc cece ence ees 4 Tooth Cutting Blade Dual String Cutting Head Shoulder Strap ara ania ac IE Da A ap RRA Single Quick Snap Trimming bine Diameter narsi nezir rc ei oe ak a EES 0 105 in 2 66 mm Cutting Path Diameter ics ces a 34 sun ne a AA 18 in 45 72 cm All specifications are based on the latest product information available at the time of printing We reserve the right to make changes at any time without notice NOTES o TB42 BC IR a VW BRITTY Recortador de ME IE A A AMY zz ee eee ee 2 Ciclos O Manual del Operador a gt FASTGUIDE Ensamblado de la unidad Cuerda de arranque Sacar la unidad de la caja D Saque todo el contenido de la caja Arranque el ctrico o accesorio de arranque el ctrico opcional ESTOS ACCESORIOS OPCIONALES SE VENDEN POR SEPARADO Esta unidad posee
27. Fig 34 la tapa del filtro Fig 34 8 Gire la tapa del filtro de aire a la derecha y alinee el tornillo de la tapa con el orificio correspondiente Fig 34 Apriete el tornillo para asegurar la tapa del filtro de aire NOTA No apriete demasiado ya que puede da ar la rosca Cubierta del Bastidor del filtro de aire filtro de aire AJUSTE DE LA VELOCIDAD DE MARCHA EN VAC O ADVERTENCIA Los dientes pueden girar durante los ajustes de marcha en vac o Use ropa que lo proteja y cumpla con todas las instrucciones de seguridad para prevenir graves lesiones personales NOTA Los ajustes realizados sin cuidado pueden da ar seriamente su unidad Los ajustes del carburador deben ser realizados por un proveedor de servicio autorizado Si luego de verificar la mezcla del combustible y limpiar el filtro de aire el motor a n no funciona en m nima ajuste el tornillo de velocidad lenta de la siguiente manera 1 Arranque el motor y d jelo funcionar durante 2 3 minutos a alta velocidad regulaci n plena para que se caliente Lea las Instrucciones de Arranque y Apagado NOTA Verifique que las p as no est n en contacto con el suelo cuando ajuste la marcha lenta 2 Suelte el gatillo del regulador y deje que el motor funcione en marcha lenta Si el motor se apaga use un destornillador peque o Phillips para girar el tornillo de marcha en vac o en el sentido de las agujas del reloj d ndole 1 8 de vuelta cada vez seg n
28. Mantenga las manijas secas limpias y libres de equipado y sea mantenido para evitar incendios Consulte los reglamentos pertinentes a esos requisitos con las escombros L mpiela despu s de usarla vea las instrucciones de Limpieza y Almacenamiento autoridades estatales o locales El incumplimiento de esos requisitos puede responsabilizarle o someterle a la e Conserve estas instrucciones Cons ltelas con frecuencia y Uselas para instruir a otros usuarios Si le presta esta unidad a imposici n de una multa Esta unidad fue equipada en la f brica con un parachispas Si requiere sustituci n alguien pr stele tambi n estas instrucciones hay una Pantalla Parachispas disponible Pieza 753 06418 al contactar el departamento de servicio CONSERVE ESTAS INSTRUCCIONES Los s mbolos de seguridad se utilizan para llamar su atenci n sobre posibles peligros Los s mbolos de seguridad y sus explicaciones merecen toda su atenci n y comprensi n Los s mbolos de seguridad no eliminan ning n peligro por s mismos Las instrucciones o advertencias que ofrecen no substituyen las medidas adecuadas de prevenci n de accidentes e SIMBOLOS DE SEGURIDAD E INTERNACIONALES Este manual del operador describe los s mbolos y figuras de seguridad e internacionales que pueden SIMBOLO SIGNIFICADO aparecer en este producto Lea el manual del operador para obtener informaci n completa acerca de la seguridad ensamble operaci n y mantenimiento y reparaci n
29. Squeeze the throttle control lever Pull the starter rope 5 times 6 Place the choke lever in Position 2 Fig 19 7 Squeeze the throttle control pull the starter rope in a controlled motion 3 to 5 times to start engine 8 Keep the throttle squeezed and allow the engine to warm up for 30 to 60 seconds 9 Continue squeezing the throttle control move the choke lever to Position 3 Fig 19 and continue warming the engine for an additional 60 seconds The unit may be used during this time NOTE Unit is properly warmed up when engine accelerates without hesitation IF the engine hesitates return the choke lever to Position 2 Fig 19 and continue warm up IF the engine does not start go back to step 3 IF the engine fails to start after 2 attempts place the choke lever in Position 3 and squeeze the throttle control Pull the starter rope out with a controlled and steady motion 3 to 8 times The engine should start If not repeat IF WARM If the engine is already warm go back to step 6 STOPPING INSTRUCTIONS 1 Release the throttle control and allow the engine to cool down by idling 2 Press and hold the On Off Control switch in the OFF O position until the unit comes to a complete stop Fig 18 IF USING THE OPTIONAL ELECTRIC STARTER OR POWER START BIT ACCESSORY HOW TO START THE UNIT USING THE ELECTRIC STARTER OR POWER START BIT ACCESSORY NOTE This Unit Can Use an Electric Start or Power Start Bit Optio
30. UNCIONAMIENTO SEGURO A NECESITA AYUDA LLAME AL 1 800 828 5500 EN EE UU O AL 1 800 668 1238 EN CANADA 769 07387 P01 11 11 INDICE DE CONTENIDOS NORMAS PARA UNA OPERACION SEGURA Llamadas a apoyo al cliente sssr ca rra a need 9 Normas para na Operaci n SEQU A seee ie enis raba a A na a A 9 e Siempre mezcle y agregue el combustible en un rea exterior bien ventilada donde no haya chispas ni llamas No fume Conozca su Unidad sico a id eddie Ge aer ia 10 e No opere nunca la unidad si la tapa del combustible no est bien asegurada en su lugar Instrucciones de ensamble o ooooooooon ee eee ee ee ee ee eee eee eens 10 e Evite el peligro de incendio debido a combustible derramado Limpie de inmediato todo combustible derramado de la Informaci n del aceite y del combustible 11 unidad antes de encenderla Antes de arrancar el motor aleje la unidad a una distancia de 30 pies 9 1 m como m nimo ci n del aceite y del combustible 2 1 eee een nn ern del lugar dls abasto de combustible No fume Instrucciones de arranque yapagado 2 eee ete eee 11 BR BER a oie e No arranque ni use nunca la unidad dentro de una habitaci n o edificio cerrados Respirar los vapores de escape puede Instrucciones de operaci n s siisi isei auk d daib doe a EMIR EE EE Dai SLEE EUA OEE aAa CDan di EEE iaia 12 ocasionarle la muerte Opere esta unidad solamente en un rea exterior bien ventilada Instrucciones de mantenimiento y reparaci
31. WARNING Thrown objects and loud noise can cause severe eye injury and hearing loss Wear eye protection meeting ANSI Z87 1 1989 standards and ear protection when operating this unit Use a full face shield when needed e UNLEADED FUEL Always use clean fresh unleaded fuel e OIL Refer to operator s manual for the proper type of oil e DO NOT USE E85 FUEL IN THIS UNIT WARNING It has been proven that fuel containing greater than 10 ethanol will likely damage this engine and void the warranty e ON OFF STOP CONTROL ON START RUN e ON OFF STOP CONTROL OFF or STOP O BOP e CHOKE CONTROL HIN IE 4 e FULL choke position 2 e PARTIAL choke position 3 e RUN choke position e KEEP BYSTANDERS AWAY WARNING Keep all bystanders especially children and pets at least 50 feet 15 m from the operating area e THROWN OBJECTS AND ROTATING CUTTER CAN CAUSE SEVERE INJURY WARNING Small objects can be propelled at high speed causing injury Keep away from the rotating rotor 4 gt EN 4 gir N e HOT SURFACE WARNING Do not touch a hot engine These parts get extremely hot from operation and may cause severe burns When the unit is turned off the engine will remain hot for a short time e SHARP BLADE WARNING Sharp blade on cutting attachment shield To prevent serious injury do not touch the line cutting blade um KNOW YOUR UNIT APPLICATIONS As a trimmer Choke Lever Sp
32. a cuchilla e CUCHILLA AFILADA ADVERTENCIA La protecci n del accesorio de corte contiene una cuchilla ADVERTENCIA La gasolina es muy inflamable y sus gases pueden explotar si se encienden Tome las siguientes precauciones e Almacene el combustible solamente en los recipientes dise ados y aprobados espec ficamente para estos materiales e Pare siempre el motor y deje que se enfr e antes de llenar el tanque de combustible No quite nunca la tapa del tanque de combustible ni eche combustible cuando el motor est caliente Antes de llenar el tanque afloje siempre la tapa lentamente para disipar la presi n del mismo No fume e0 07407840 971D APLICACIONES Como recortadora Buj a de encendido Palanca del obturador Mango de la e Corte de c sped y hierbas delgadas Silenciador 3 cuerda de Recorte de bordes arranque e Recorte decorativo alrededor de Cubierta del rboles cercos etc filtro de aire HERRAMIENTAS DE ENSAMBLAJE Manjo del ej Y NECESARIAS en e Destornillador Phillips Control de encendido y apagado Tapa del combustible Manija en J ug Gatillo del regulador Bombilla del cebador Bastidor del eje Cuchilla de corte de linea wo Protecci n accesoria de corte Accesorio de corte INSTRUCCIONES DE ENSAMBLE ADVERTENCIA No opere nunca la recortadora sin el protector accesorio de corte colocado en su lugar para evitar graves lesiones personales
33. a mal uso abuso uso comercial negligencia accidente mantenimiento inapropiado alteraci n vandalismo hurto fuego agua o da os debidos a otros riesgos o desastre natural Los da os ocasionados por la instalaci n o el uso de cualquier accesorio o aditamento que no est aprobado por Troy Bilt y que sea usado con el los producto s contemplados en este manual anular n la garant a con respecto a cualquier da o resultante Esta garant a est limitada a noventa 90 d as a partir de la fecha de compra original al detalle de cualquier producto Troy Bilt que se use para alquiler para prop sitos comerciales o cualquier otro prop sito que genere ingresos C MO OBTENER SERVICIO El servicio de garant a est disponible A TRAV S DE SU DISTRIBUIDOR DE SERVICIO LOCAL AUTORIZADO AL PRESENTAR EL COMPROBANTE DE COMPRA Para localizar al distribuidor en su rea busque el aviso clasificado en las P ginas Amarillas llame al 1 800 828 5500 en EE UU o al 1 800 668 1238 en Canada o escriba a Troy Bilt LLC PO Box 361131 Cleveland OH 44136 0019 No se aceptar ning n producto que sea enviado directamente a la f brica a menos que haya recibido autorizaci n previa por escrito por parte del Departamento de Servicio al Consumidor de Troy Bilt Esta garant a limitada no ofrece cobertura en los siguientes casos A Sincronizaciones buj as ajustes de carburadores filtros B Art culos de desgaste perillas percusivas carretes externos l nea
34. a turn at a time as needed to reduce idle speed Checking the fuel mixture cleaning the air filter and adjusting the idle speed should solve most engine problems If not and all of the following are true e the engine will not idle e the engine hesitates or stalls on acceleration Fig 35 WARNING The cutting attachment will spin during idle speed adjustments Wear protective clothing and observe all safety instructions to prevent serious personal injury e there is a loss of engine power Have the carburetor adjusted by an authorized service dealer REPLACING THE SPARK PLUG Use replacement 753 06193 a Champion RDJ7J spark plug or equivalent The correct air gap is 0 025 inch 0 635 mm Remove the plug after every 25 hours of operation and check its condition 1 Stop the engine and allow it to cool Grasp the plug wire firmly and pull it from the spark plug 2 Clean around the spark plug Remove the spark plug from the cylinder head by turning a 5 8 inch socket counterclockwise WARNING Do not sand blast scrape or clean electrodes Grit in the engine could damage the cylinder 3 Replace a cracked fouled or dirty spark plug Set the air gap at 0 025 in 0 635 mm using a feeler gauge Fig 36 en 4 Install a correctly gapped spark plug in the cylinder head Tighten by turning the 5 8 inch socket clockwise until snug Fig 36 If using a torque wrench torque to 110 120 in elb
35. a unidad El control de Encendido Apagado est en la posici n ENCENDIDO 1 en todo momento Fig 18 3 Oprima y suelte completamente la pera del cebador 10 veces lentamente Deber verse alguna cantidad de combustible en la pera del cebador Fig 19 Si no se ve combustible en la pera oprima la pera hasta que se vea el combustible 4 Coloque la palanca del obturador en la Posici n 1 Fig 19 5 Ag chese en la posici n de arranque Fig 20 Coloque el arrancador el ctrico o el accesorio de arranque el ctrico opcional en la parte trasera de la unidad Consulte la secci n de Operaci n del manual del operador del Arrancador El ctrico o Accesorio de Arranque El ctrico Opcional Power Start Bit 6 Oprima la palanca del control del regulador Apriete y mantenga apretado el bot n de ENCENDIDO I del arrancador el ctrico o taladro durante 2 segundos 7 Coloque la palanca del obturador en la Posici n 2 Fig 19 8 Oprima la palanca del control del regulador apriete y mantenga apretado el bot n de ENCENDIDO I del arrancador el ctrico o taladro durante 2 segundos hasta que la unidad arranque 9 Mantenga apretado el control del regulador desmonte el arrancador el ctrico o taladro de la unidad y deje que el motor se caliente durante 30 a 60 segundos 10 Mantenga apretado el control del regulador ponga la palanca del obturador en la Posici n 3 Fig 19 y haga funcionar la unidad durante 60 segundos m s La unidad se puede u
36. ake sure it moves freely Replace the bump knob if damaged NS 3 2 Remove the inner reel from the outer spool Fig Bump Koa E 25 3 Remove spring from the inner reel Fig 25 Bolt Fig 25 4 Use a clean cloth to clean the the inner reel spring shaft and inner surface of the outer spool Fig 26 5 Check the indexing teeth on the inner reel and outer spool for wear Fig 27 If necessary remove burrs or replace the reel and spool NOTE SplitLine can only be used with the inner reel with the slotted holes Single line can be used on either type of inner reel Use Figure 28 to identify the inner reel you have Indexing Teeth LOOSE REW Q NOTE Always use the correct line length when TA installing trimming line on the unit The line may v Ing NA not release properly if the line is too long y e IS Single Line Installation N Go To Step 8 for SplitLine Installation 6 Take approximately 18 feet 6 m of new trimming line loop it into two equal lengths Insert each end of the line through one of the two holes in the inner reel Fig 29 Pull the line through the inner reel so that the loop is as small as possible 7 Wind the lines in tight even layers onto the reel Fig 30 Wind the line in the direction indicated on the inner reel Place your index finger between the two lines to stop the lines from over lapping Do not overlap the ends of the line Proceed to s
37. al Cliente al 1 800 828 5500 en Estados Unidos o el q raea grand i p y P A eas ne a e d s d la unidad 1 800 668 1238 en Canada Puede encontrar mas informacion sobre la unidad en nuestro sitio Web ee enw troybilt com o troybilt ca e No opere el motor a m s velocidad de la necesaria para cortar recortar o recortar bordes No haga funcionar el motor a i A ae u alta velocidad cuando no este cortando con Maa recibir SOIVICIOS llame al Departamento de Atencion al Cliente para que le faciliten una e Pare siempre el motor cuando deje de cortar o cuando est caminando de un lugar de corte hacia otro lista de los distribuidores de servicio autorizados cercanos a usted El servicio a esta unidad tanto durante como despu s del per odo cubierto por la garant a debe ser llevado a cabo solamente por e Si golpea o se enreda con un objeto extra o pare el motor inmediatamente y verifique si ha habido alg n da o No lo HERAS ae a A i de opere antes de reparar el da o No opere la unidad con piezas sueltas o da adas un distribuidor de servicio autorizado y aprobado Cuando vaya a dar mantenimiento al equipo utilice sE BEER e Pare la unidad apague el motor y desconecte la buj a para mantenimiento o reparaci n solo piezas de repuesto id nticas Use solamente piezas y accesorios de reemplazo del fabricante del equipo original para esta unidad stos est n disponibles en su proveedor de servicio autorizado El uso de cualquier p
38. apacidad del tanque de combustible o oooooommococonmormn 14 onzas 397 ml Peso de la unidad Sin combustible con accesorio de corte y manija en D 11 13 libras 5 5 9 kg Mecanismo de corte 005 4 dientes corte de la hoja cadena doble la cabeza de corte Diametro de la bobina de linea cirerers bavi weed chee rar nn a 3 pulg 76 2 mm Di metro de la linea de corte 1 2 ee 0 105 pulg 2 66 mm Di metro de la trayectoria de corte 00 0 cece tee 18 pulg 45 72 cm Toda las especificaciones contenidas en este manual se basan en la informaci n m s reciente disponible en el momento de impresi n del manual Nos reservamos el derecho de hacer cambios en cualquier momento sin aviso previo 14 NOTES 15 MANUFACTURER S LIMITED WARRANTY FOR GARANTIA LIMITADA DEL FABRICANTE PARA OTROY BILT The limited warranty set forth below is given by Troy Bilt LLC Troy Bilt with respect with new merchandise purchased and used in the United States its possessions and territories Troy Bilt warrants this product against defects in material and workmanship for a period of two 2 years commencing on the date of original purchase and will at its option repair or replace free of charge any part found to be defective in material or workmanship This limited warranty shall only apply if this product has been operated and maintained in accordance with the Operator s Manual furnished with the
39. ark Plug e Cutting grass and light weeds u er e Edging Muffler Grip e Decorative trimming around trees a fences etc ASSEMBLY TOOLS REQUIRED PER m o e Phillips screwdriver A Fuel Cap On Off Control Air Filt e Cover J Handle un Throttle EZ Link Control Primer Bulb Shaft a ok Cutting Head a lt lt Cutting Head Shield ASSEMBLY INSTRUCTIONS WARNING To prevent serious personal injury never operate the trimmer without the cutting attachment shield in place INSTALL AND ADJUST THE J HANDLE On some units the J handle may be pre installed In this case loosen the screws and go to step 5 1 Place the J handle between the top and middle clamp pieces Fig 1 2 While holding the three pieces together install the four 4 screws through the top clamp and into middle clamp NOTE The holes in the top and middle clamp will line up only when assembled correctly 3 Place the clamps and the J handle over the shaft housing and onto the bottom clamp 4 Hold each hex nut in the bottom clamp recess with a finger Start screws with a large Phillips screwdriver Do not tighten until you make the handle adjustment 5 Slide the J handle in or out until the arrow white line on the decal touches the clamp assembly Fig 2 You must first loosen the screws if the handle is pre installed 6 While holding the unit in the operating position position the J handle to the location that provides you the best grip 7 Tight
40. bove limitation may not apply to you In no event shall recovery of any kind be greater than the amount of the purchase price of the product sold Alteration of the safety features of the product shall void this Warranty You assume the risk and liability for loss damage or injury to you and your property and or to others and their property arising out of the use or misuse or inability to use the product This limited warranty shall not extend to anyone other than the original purchaser original lessee or the person for whom it was purchased as a gift How State Law Relates to this Warranty This warranty gives you specific legal rights and you may also have other rights which vary from state to state To locate your nearest service dealer dial 1 800 828 5500 in the United States or 1 800 668 1238 in Canada Troy Bilt LLC concede la garantia limitada establecida debajo para mercancias nuevas que sean compradas y usadas en los Estados Unidos sus posesiones y territorios Troy Bilt LLC garantiza este producto contra defectos en el material y la mano de obra durante un per odo de dos 2 a os a partir de la fecha de compra original y a su entera discreci n arreglar o substituir sin costo alguno cualquier pieza cuyo material o mano de obra se considere defectuoso Esta garant a limitada se deber aplicar nicamente si este producto ha sido manejado y mantenido de acuerdo al Manual del Operario incluido con el producto y si no ha sido sometido
41. bump knob to make sure it moves freely Replace the bump knob if damaged 2 Remove the old inner reel from the outer spool Fig 25 3 Remove the spring from the old inner reel Fig 25 4 Place the spring in the new inner reel NOTE The spring must be assembled on the inner reel before reassembling the cutting attachment 5 Insert the ends of the line through the eyelets in the outer spool Fig 33 6 Place the new inner reel inside the outer spool Push the inner reel and outer spool together While holding the inner reel and outer spool grasp the ends and pull firmly to release the line from the holding slots in the spool 7 Hold the inner reel in place and install the bump knob by turning counterclockwise Tighten securely MAINTENANCE AND REPAIR INSTRUCTIONS AIR FILTER MAINTENANCE Cleaning the Air Filter Air Filter Housing Air Filter Failure to maintain your air filter properly can result in poor performance or can cause permanent damage to your engine 1 Open the air filter cover by unscrewing the cover screw Fig 34 2 Remove the air filter and the screen that sits behind it Fig 34 3 Wash the filter in detergent and water Rinse the filter thoroughly and allow it to dry 4 Apply enough clean SAE 30 motor oil to lightly coat the filter Slots 5 Squeeze the filter to spread and remove excess oil 6 Replace the air filter and the screen that s
42. bustible ha os AO iire cheie sido drenado del carburador 3 Espere a que el motor se enfr e Qu tele la buj a y eche 5 gotas de cualquier aceite de motor de 2 EL MOTOR NO TIENE SUFICIENTE POTENCIA O SE AHOGA AL CORTAR tiempos de alta calidad en el cilindro Tire lentamente de la cuerda de arranque para distribuir el aceite Vuelva a poner la buj a El combustible est viejo m s de 30 d as y o mal Drene el tanque de combustible y eche combustible NOTA Saque la buj a de encendido y drene todo el aceite del cilindro antes de intentar arrancar el mezclado fresco mezclado adecuadamente recortador despu s de su almacenamiento La buj a de encendido est arruinada Remplacez ou nettoyez la 4 Limpie bien la unidad e inspeccione para ver si existen partes flojas o da adas Repare o cambie las artes da adas y ajuste los tornillos tuercas o pernos que puedan estar flojos La unidad est ahora ista para ser guardada LA CABEZA DE CORTE NO HACE AVANZAR LINEA El accesorio de corte est atascado de hierba Pare el motor y limpie el accesorio de corte El accesorio de corte no tiene l nea Coloque una l nea nueva El carrete interior est trabado Rebobine el carrete interior ACCESORIO OPCIONAL La cabeza de corte est sucia Limpie el carrete interior y la bobina exterior La l nea se ha soldado Desarme saque la secci n soldada y rebobine la l nea ARRANCADOR ELECTRICO Y ACCESORIO DE ARRANQUE EL CTRICO OPCIONAL POWER START BIT Esta unidad est
43. con alcohol absorbe agua Una cantidad tan peque a como el 1 de agua en el combustible puede causar la separaci n del combustible y el aceite Forma cidos cuando est almacenado Cuando use combustible mezclado con alcohol use combustible nuevo de menos de 30 d as Uso de combustibles de mezcla Si usted opta por usar un combustible de mezcla o si su uso es inevitable tome las precauciones recomendadas e Use siempre una mezcla fresca de combustible seg n lo indica su manual del operador e Use el aditivo especial de combustible STA BIL o uno similar e Agite siempre la mezcla de combustible antes de cargarlo en la unidad e Drene el tanque y haga funcionar el motor en seco antes de guardar la unidad Uso de aditivos en el combustible GASOLINA SIN ACEITEDE2 LOMO CICLOS EE UU PRECAUCI N Para que el motor funcione correctamente y con la mayor fiabilidad preste mucha atenci n a las instrucciones de mezcla de aceite y combustible del envase de aceite de 2 ciclos El uso de combustible mezclado en forma incorrecta puede da ar seriamente el motor La botella de aceite de 2 ciclos que vino con su unidad contiene un aditivo en el combustible que ayudar a inhibir la corrosi n y a reducir la formaci n de dep sitos de goma Se recomienda que use s lo el aceite de 2 ciclos con esta unidad Si es inevitable use un buen aceite de 2 ciclos elaborado para motores enfriados por aire junto con un aditivo para el combustibl
44. de corte carretes internos polea de arranque cuerdas de arranque correas motoras vio cadenas gu a bares dientes de cultivadora C Troy Bilt no le ofrece ninguna garant a a los productos que sean vendidos o exportados fuera de los Estados Unidos de Am rica sus posesiones y territorios excepto aquellos que se vendan a trav s de los canales de distribuci n para exportaci n autorizados por Troy Bilt Troy Bilt se reserva el derecho a cambiar o mejorar el dise o de cualquier producto Troy Bilt sin adoptar ninguna obligaci n para modificar cualquier producto fabricado con anterioridad Ninguna garant a impl cita es aplicable despu s del per odo de aplicabilidad de la garant a expresa escrita con anterioridad incluyendo cualquier garant a impl cita de comerciabilidad o idoneidad para un prop sito particular con respecto a las piezas identificadas Exceptuando lo mencionado anteriormente ninguna otra garant a expresa bien sea escrita o verbal con respecto a cualquier producto que sea concedida por cualquier persona o entidad incluyendo al distribuidor o minorista deber comprometer a Troy Bilt LLC durante el per odo de la Garant a el remedio exclusivo es el arreglo o la sustituci n del producto seg n lo establecido anteriormente Algunos estados no permiten limitaciones en cuanto al per odo de duraci n de una garant a impl cita de manera que puede que la limitaci n anterior no sea aplicable en su caso Las estipulaciones
45. de operar la unidad Elimine todos los escombros y los objetos duros o filosos ADVERTENCIA Mantenga a todos los espectadores en especial a ni os y tales como cristal alambre etc animales dom sticos a por lo menos 50 pies 15 m del rea de corte e Est consciente del riesgo de lesi n en la cabeza las manos y los pies e No permita ni os espectadores ni mascotas en el rea Los ni os los espectadores y las mascotas deben estar fuera de ADVERTENCIA DE SUPERFICIE CALIENTE un radio de 50 pies 15 m como m nimo de todas formas los espectadores correr n el riesgo de ser golpeados por Not il ES z iind Tan Pues Est rt objetos lanzados por la unidad Se debe exhortar a los espectadores a que usen protecci n para los ojos Si se le acerca WELE U SUENIE S M IN el mero calle net ECO quemas ESS penes SE alguien apague la unidad de inmediato calientan mucho con el uso Luego de apagarse permanecen calientes durante un e Use s lo l nea de reemplazo del fabricante original del equipo con un di metro de 0 105 de pulgada 2 66 mm Nunca use corto tiempo l nea reforzada con metal alambre o soga Se pueden romper y convertirse en proyectiles peligrosos e Oprima el control del estrangulador y compruebe que regresa autom ticamente a la posici n de marcha en vac o Haga todos los ajustes o reparaciones antes de usar la unidad E 1 ADVERTENCIAS DE SEGURIDAD PARA LAS UNIDADES A GASOLINA afilada Para prevenir graves lesiones no toque l
46. de salida Ajuste bien NOTA El ret n de la cuchilla debe estar instalado en el eje de salida en la posici n ilustrada para que el accesorio de corte funcione en forma correcta 6 Saque la varilla de cierre 7 Instale el protector accesorio de corte Lea Remoci n e instalaci n del protector accesorio de corte Sentido horario Fig 16 Accesorio de corte Sa gt Ret n de la cuchilla Buje del eje de salida ADVERTENCIA Para evitar graves lesiones personales el protector accesorio de corte DEBE estar instalado en todo momento cuando use la unidad como recortador de c sped INFORMACI N DEL ACEITE Y DEL COMBUSTIBLE LL EN INSTRUCCIONES PARA MEZCLAR EL ACEITE Y EL COMBUSTIBLE El combustible viejo o mal mezclado son los motivos principales del mal funcionamiento de la unidad Aseg rese de usar combustible nuevo limpio y sin plomo Siga las instrucciones en detalle para mezclar correctamente el aceite y el combustible Definici n de los combustibles de mezcla ADVERTENCIA NO USE COMBUSTIBLE E85 EN ESTA UNIDAD Se ha comprobado que es probable que el combustible con m s de un 10 de etanol da e este motor lo que anular la garant a 3 8 LITROS 95 mL 1 GALON de 3 2 ONZAS FLUIDAS Los combustibles actuales con frecuencia son una mezcla de gasolina y PROPORCION DE LA MEZCLA 40 1 oxigenantes como por ejemplo etanol metanol o MTBE ter El combustible mezclado
47. durante los ajustes del carburador Use ropa que lo proteja y cumpla con todas derecho de hacer cambios en cualquier momento sin aviso previo las instrucciones de seguridad para prevenir graves lesiones personales Copyright O 2011 MTD SOUTHWEST INC Todos los derechos reservados Use la unidad solamente de d a o con buena luz artificial e Evite arranques accidentales Est en la posici n de arranque cada vez que hale la cuerda de arranque El operador y la unidad deben estar en una posici n estable al arrancar Consulte las Instrucciones de Arranque Parada LLAMADAS A APOYO AL CLIENTE ne la herramienta correcta Use esta herramienta solamente para el prop sito para el cual fue dise ada e No se estire demasiado Mantenga siempre la base de apoyo y equilibrio adecuados NO DEVUELVA ESTA UNIDAD AL VENDEDOR PARA SOLICITAR SERVICIO POR GARANT A Sostenga siempre la unidad con ambas manos cuando la opere Mantenga un agarre firme sobre ambas manijas DEBER PRESENTAR EL COMPROBANTE DE COMPRA e Mantenga las manos la cara y los pies alejados de todas las partes en movimiento No toque ni trate de parar el accesorio sai A is R ig feat de corte cuando est girando T Arai solicitar asistencia en relacion con elensamblaje 195 controles la operaci n o el mantenimiento e No toque el motor la caja de engranajes ni el silenciador Estas piezas est n muy calientes durante la operaci n incluso de la unidad llame al Departamento de Atenci n
48. e como por ejemplo el estabilizador de gasolina STA BIL o similar Agregue 23 mL 0 8 onzas de aditivo de combustible por gal n de combustible de acuerdo con las instrucciones del envase NUNCA agregue aditivos directamente en el tanque de combustible de la unidad Mezcle bien la proporci n correcta de aceite para motor de 2 ciclos y gasolina sin plomo en una lata de combustible por separado Use una proporci n de 40 1 de combustible y aceite No los mezcle directamente en el tanque de combustible de la unidad Consulte las proporciones espec ficas de mezcla de gasolina y aceite en la tabla siguiente NOTA 3 8 litros un gal n de gasolina sin plomo mezclada con una botella de 95 mL 3 2 onzas de aceite de 2 ciclos es una proporci n de 40 1 de combustible y aceite NOTA Elimine la mezcla vieja de aceite y combustible de acuerdo con los reglamentos federales estatales y locales ADVERTENCIA La gasolina es muy inflamable Los gases pueden explotar si se encienden Apague siempre el motor y espere que se enfr e antes de cargar el tanque de combustible No fume mientras llena el tanque Mantenga las chispas y las llamas lejos del rea CARGA DE COMBUSTIBLE EN LA UNIDAD ADVERTENCIA Saque la tapa del combustible lentamente para evitar lesionarse con el rociado del combustible No opere nunca la unidad sin la tapa del combustible firmemente colocada en su lugar ADVERTENCIA Cargue el combustible en un rea exterior limpia y b
49. e equipped with a spark arrestor maintained in effective working order or the engine be e Store the unit in a dry area locked up or up high to prevent unauthorized use or damage Keep out of the constructed equipped and maintained for the prevention of fire Check with your state or local authorities for reach of children regulations pertaining to these requirements Failure to follow these requirements could subject you to liability e Never douse or squirt the unit with water or any other liquid Keep handles dry clean and free from or a fine This unit is factory equipped with a spark arrestor If it requires replacement ask your LOCAL debris Clean after each use See the Cleaning and Storage instructions SERVICE DEALER to install the Accessory Part 753 06418 Muffler Assembly RULES FOR SAFE OPERATION The purpose of safety symbols is to attract attention to possible dangers The safety symbols and their explanations deserve careful attention and understanding The safety warnings do not by themselves eliminate any danger The instructions or warnings they give are not substitutes for proper accident prevention measures SYMBOL MEANING OO OOOO y y O y A SAFETY ALERT Indicates danger warning or caution Attention is required in order to avoid serious personal injury May be used in conjunction with other symbols or pictographs DANGER Failure to obey a safety warning will result in serious injury to yourself or to others
50. ely with a flat blade screwdriver Fig 6 REMOVE THE CUTTING ATTACHMENT AND INSTALL THE CUTTING BLADE NOTE To make cutting blade removal and installation easier place the unit on the ground or on a work bench Remove the Cutting Attachment Shield WARNING The gear housing gets hot with use It can result in injury to the operator The housing remains hot for a short time even after the unit is turned off Do not touch the gear housing until it has cooled See Remove and Install the Cutting Attachment Shield Remove the Cutting Attachment 1 Align the shaft bushing hole with the locking rod slot and insert the locking rod into the shaft bushing hole Fig 10 2 Hold the locking rod in place by grasping it next to the boom of the unit Fig 11 3 While holding the locking rod remove the cutting attachment by turning it clockwise off of the output shaft Fig 12 Store the cutting attachment for future use NOTE The blade retainer under the cutting attachment will be used when installing the cutting blade Output Shaft Output Shaft Bushing TY 3 Shaft Bushing Hole Locking Rod Slot 4 Ke K Locking Rod 4 Cutting Attachment ASSEMBLY INSTRUCTIONS Install the Cutting Blade WARNING To avoid serious personal injury always wear gloves while handling or installing the blade 1 Place the cutting blade on the output shaft Nut bushing Fig 13
51. en the clamp screws evenly until the J handle is secure OPERATING THE EZ LINK SYSTEM The EZ Link system enables the use of these optional Add Ons Mach A Irimmer ve csi tirao rra aa AF720 Hedge MM 00 A oy A A e naeh har AH720 BrUSHCUISE acaricio dana ainda ale abr iden ias ida a islas ade BC720 Gultivator ei da en o oo Has ae GC720 A RINA LE720 Pole Saw iio eat ee en Or o ie ea PS720 Straight Shaft TIMME u iaa ee A AA des La oe ERR A SS725 Turbo Blower 4 vo aaa ve aa a ak TB720 Do NOT use this Add On with an electric powered unit REMOVING THE ADD ON 1 Turn the knob counterclockwise to loosen Fig 5 2 Press and hold the release button Fig 3 3 While firmly holding the upper shaft housing pull the lower shaft housing straight out of the EZ Link coupler Fig 4 EZ Link Coupler Release Upper Shaft Housing Lower Shaft Guide Recess Housing Fig 3 Fig 4 90 Edging Hole Trimmer Only INSTALLING THE ADD ON NOTE To make installing or removing the add on easier place the unit on the ground or on a work bench 1 Turn knob counterclockwise to loosen Fig 5 2 While firmly holding the add on push it straight into the EZ Link coupler Fig 4 NOTE Aligning the release button with the guide recess will help installation Fig 3 Knob 3 Turn the knob clockwise to tighten Fig 5 Fig 5 For decorative trimming edging with the line cutting head loc
52. endido est arruinada Remplacez ou nettoyez le lama o chispa e Espere que el motor se enfr e antes de guardar la unidad e Guarde la unidad bajo llave para prevenir el uso por EE MOTOR NO FUNCIONA EN MINIMA personas no autorizadas y su da o El filtro de aire est obstruido Cambie o limpie el filtro de aire e Guarde la unidad en un rea seca y bien ventilada El combustible est viejo m s de 30 d as y o mal Drene el tanque de combustible y eche combustible e Guarde la unidad fuera del alcance de los ni os mezclado fresco mezclado adecuadamente Almacenamiento a corto plazo de 1 a 2 semanas Velocidad de marcha en vac o inadecuada Ajuste la velocidad de marcha en vac o 1 Guarde la unidad en posici n horizontal Si no fuera posible guarde la unidad verticalmente con el motor hacia arriba Almacenamiento prolongado EL MOTOR NO ACELERA 1 Quite la tapa del tanque de combustible voltee la unidad y vac e el combustible en un contenedor El combustible est viejo m s de 30 d as y o mal Drene el tanque de combustible y eche combustible aprobado mezclado fresco mezclado adecuadamente NOTA No use gasolina que haya estado guardada durante m s de 30 d as Elimine la gasolina vieja de El accesorio de corte est atascado de hierba Pare el motor y limpie el accesorio de corte acuerdo con las normas federales estatales y locales 2 Arranque el motor y d jelo funcionar hasta que se ahogue Esto asegura que todo el com
53. establecidas en esta Garant a ofrecen la soluci n nica y exclusiva que resulte de las ventas Troy Bilt no deber ser responsable de p rdidas o da os incidentales o consecuentes que incluyan sin limitaci n gastos incurridos debido a la sustituci n de servicios de mantenimiento de prados transporte o gastos relacionados o gastos de alquiler para reemplazar temporalmente un producto bajo garant a Algunos estados no permiten limitaciones en cuanto al per odo de duraci n de una garant a impl cita de manera que puede que la limitaci n anterior no sea aplicable en su caso Ning n tipo de recuperaci n deber ser superior al precio de compra del producto vendido en ning n caso La alteraci n de las caracter sticas de seguridad del producto deber anular esta Garant a Usted adopta el riesgo y la obligaci n de la p rdida da o o lesi n en su persona o a su propiedad y o la de otras personas y sus propiedades que se origine a ra z del uso o mal uso o la incompetencia para usar el producto Esta garant a limitada no deber cubrir a ninguna otra persona distinta al comprador original arrendatario original o la persona para la cual se compr en calidad de regalo Relaci n de las leyes estatales con esta Garant a Esta garant a le confiere derechos legales espec ficos y puede que usted tambi n tenga otros derechos los cuales var an en cada estado Para localizar al distribuidor de servicio local m s cercano marque el n mero
54. gar donde se corta Por ejemplo la l nea se desgastar m s r pido cuando corte contra un muro que cuando corte alrededor de un rbol La l nea puede cortarse por e Enredarse con un objeto extra o e Fatiga normal de la l nea e Intentar cortar hierbas gruesas y le osas e Forzar la l nea en objetos como paredes o postes de Cercos RECORTE DECORATIVO El recorte decorativo se realiza eliminando toda la vegetaci n de alrededor de los rboles postes cercos etc Gire toda la unidad a modo de que el accesorio de corte se ubique a un ngulo de 30 con el suelo Fig 22 USO DE LA CUCHILLA DE CORTE Antes de operar la unidad con la cuchilla de corte p rese en posici n de corte Fig 23 Lea C mo sostener el Recortador ADVERTENCIA Use siempre protecci n para sus ojos audici n pies y cuerpo para reducir el riesgo de una lesi n al operar esta unidad ADVERTENCIA No use la cuchilla de corte para recortar bordes ni como un recortador de bordes puede causarle graves lesiones personales a usted o a los dem s Consejos para el uso de la cuchilla de corte ADVERTENCIA Cuando la cuchilla giratoria hace contacto con un objeto que no corta de inmediato puede ocurrir el impulso de la cuchilla El impulso de la cuchilla puede ser lo suficientemente violento como para hacer que la unidad y o el operador sean impulsados en cualquier direcci n y posiblemente perder el control de la unidad El impulso de
55. idad e CONTROL DEL OBTURADOR 1 e Posici n de OBTURACI N COMPLETA 2 e Posici n de OBTURACI N PARCIAL 3 e Posici n de MARCHA Por favor lea estas instrucciones para su propia seguridad y las de los espectadores antes de hacer funcionar la unidad Por favor mantenga estas instrucciones en un lugar seguro para uso futuro e Lea las instrucciones cuidadosamente Familiaricese con los controles y el uso adecuado de la unidad e No opere esta unidad cuando est cansado enfermo o bajo la influencia de alcohol drogas o medicamentos e Los ni os y los adolescentes menores de 15 a os de edad no deben usar la unidad Los adolescentes pueden hacerlo bajo la supervisi n de un adulto e Todos los dispositivos de protecci n y los accesorios de seguridad deben estar instalados adecuadamente antes de Operar la unidad e Inspeccione la unidad antes de usarla Reemplace las piezas da adas Verifique si hay fugas de combustible Aseg rese de que todos los fijadores est n en su lugar y asegurados Reemplace las piezas que est n agrietadas astilladas o e LOS OBJETOS DESPEDIDOS Y LA CUCHILLA ROTATIVA PUEDEN CAUSAR GRAVES LESIONES ADVERTENCIA No opere esta unidad si la protecci n pl stica de l nea no est colocada en su lugar Mant ngase alejado de la cabeza de corte giratorio da adas en cualquier forma No opere la unidad con piezas sueltas o da adas MANTENGA ALEJADOS A LOS ESPECTADORES Inspeccione cuidadosamente el rea antes
56. ien ventilada Limpie de inmediato todo combustible que se haya derramado Evite crear una fuente de encendido con el combustible derramado No arranque el motor hasta que se hayan evaporado los gases del combustible 1 Saque la tapa de la gasolina 2 Coloque el pico del recipiente de gasolina en el orificio de llenado del tanque de gasolina y llene el tanque NOTA No llene el tanque demasiado 3 Limpie toda la gasolina que pueda haberse derramado 4 Vuelva a instalar la tapa de la gasolina 5 Mueva la unidad por lo menos 9 1 m 30 pies de la fuente y sitio de carga antes de arrancar el motor NOTA Elimine la gasolina vieja de acuerdo a los reglamentos federales estatales y locales INSTRUCCIONES DE ARRANQUE Y APAGADO Apagado O ADVERTENCIA Use esta unidad s lo en un rea exterior bien ventilada Los gases de escape de mon xido de carbono pueden ser letales en un rea cerrada ADVERTENCIA Evite los arranques accidentales Col quese en posici n de inicio cuando tire de la cuerda de arranque Fig 6 El Control del operador y la unidad deben estar en una posici n estable al arrancar la unidad para evitar graves lesiones personales regulador Fig 18 INSTRUCTIONS DE D MARRAGE Bombilla del Palanca azul cebador 1 Mezcle la gasolina con el aceite Vea las Instrucciones para Mezclar el Aceite y el Combustible 2 Llene el tanque de combustible con la mezcla de combustible aceite Consulte C mo
57. ieza o accesorio no autorizado podr a causar lesiones graves al usuario o da os a la unidad y anular su garant a e Mantenga la unidad limpia de vegetaci n y otros materiales Pudieran quedar obstruidas entre el accesorio de corte y el protector e Para reducir el peligro de incendio mantenga el motor y el silenciador libre de hierba hojas exceso de grasa o NORMAS PARA UNA OPERACION SEGURA acumulaci n de carb n OTROS AVISOS DE SEGURIDAD PARACHISPAS e Nunca almacene una unidad con combustible dentro de un edificio en el cual los vapores puedan llegar a una llama NOTA Para los usuarios en tierras forestales de los EE UU y en los estados de California Maine Oregon expuesta o una chispa y Washington Todos los terrenos forestales de los EE UU y el estado de California C digos de Recursos e Deje que el motor se enfr e antes de almacenarlo o transportarlo Aseg rese de fijar bien la unidad mientras la transporta P blicos 4442 y 4443 Oregon y Washington requieren por decreto que ciertos motores de combusti n interna e Almacene la unidad en un rea seca y cerrada o en un lugar alto para evitar uso no autorizado o da os Mant ngala que se hagan funcionar en zonas boscosas y o zonas cubiertas por pastizales est n equipados con un alejada del alcance de los ni os parachispas que sean mantenidos en buen estado de funcionamiento o que el motor sea construido est e Nunca rocie ni chorree la unidad con agua ni ning n otro l quido
58. il Reinstall the spark plug NOTE Remove the spark plug and drain all of the oil from the cylinder before attempting to start the unit after storage 4 Thoroughly clean the unit and inspect it for any loose or damaged parts Repair or replace damaged parts and tighten loose screws nuts or bolts The unit is ready for storage TROUBLESHOOTING CAUSE ACTION ENGINE WILL NOT START Empty fuel tank The primer bulb wasn t pressed enough Fill fuel tank with properly mixed fuel Press the primer bulb 10 times or until fuel is visible With the choke lever in position 3 squeeze the trigger and pull the starter rope Drain the fuel tank and add fresh properly mixed fuel Replace or clean the spark plug Engine is flooded The fuel is old over 30 days and or improperly mixed Fouled spark plug ENGINE WILL NOT IDLE Air filter is plugged The fuel is old over 30 days and or improperly mixed Improper idle speed Replace or clean the air filter Drain the fuel tank and add fresh properly mixed fuel Adjust the idle speed ENGINE WILL NOT ACCELERATE The fuel is old over 30 days and or improperly mixed Cutting head bound with grass Dirty air filter Drain the fuel tank and add fresh properly mixed fuel Stop the engine and clean the cutting head Clean or replace the air filter ENGINE LACKS POWER OR STALLS The fuel is old over 30 days and or improperly mixed Fouled spark plug Drain the fuel tank and add fresh
59. istemas pueden ser hechos por cualquier establecimiento de reparaci n persona o proveedor de servicio autorizado que arregle motores para uso fuera de la carretera NOTA Para ver la lista completa de t rminos y la cobertura de los dispositivos de control de emisiones como parachispas silenciador carburador etc lea la declaraci n de California EPA que viene junto con la unidad FRECUENCIA MANTENIMIENTO REQUERIDO CONSULTE Antes de arrancar el motor Llene el tanque de combustible con la mezcla correcta de aceite y p 13 combustible Cada 10 horas Limpie y vuelva a aceitar el filtro de aire Cada 25 horas Inspeccione la condici n y la separaci n de la buj a de encendido 12 INSTRUCCIONES DE MANTENIMIENTO Y REPARACI N INSTALACION DE LA LINEA Esta secci n cubre la instalaci n de la linea SplitLine y de la l nea individual regular Use siempre la l nea de repuestos de 2 67 mm 0 105 pulg del fabricante del equipo original Una l nea que no sea la indicada puede causar que el motor se recaliente o falle ADVERTENCIA No use nunca l nea reforzada con metal alambre cadena ni soga etc Estos elementos pueden desprenderse y convertirse en un proyectil peligroso Existen dos m todos para cambiar la l nea de corte e Bobine el carrete interior con linea nueva e Instale un carrete interior prebobinado Bobinado del carrete interior existente 1 NOTA La l nea SplitLine s lo NOTA Use siempre la longit
60. its behind it Fig 34 NOTE Operating the unit without the air filter will VOID the warranty 7 Reinstall the air filter cover Insert the hooks on the air filter housing into the slots on the air filter cover Air Filter Fig 34 Cover 8 Swing the air filter cover to the Fia 34 right and align the cover screw g with the cover screw hole Fig 11 Tighten the cover screw to secure the air filter cover NOTE Do not over tighten as this may strip the screw Air Filter Cover Hooks gt Cover NS Screw Hole Air Filter Housing IDLE SPEED ADJUSTMENT The idle speed of the engine is adjustable An idle adjustment screw is between the air filter cover and the engine starter housing Fig 35 NOTE Careless adjustments can seriously damage the unit An authorized service dealer should make carburetor adjustments If after checking the fuel mixture and cleaning the air filter the engine still will O not idle adjust the idle speed screw as follows 1 Start the engine and run for one minute to warm up Refer to Starting and Stopping Instructions 2 Release the throttle trigger and let the engine idle If the engine stops insert a small Phillips screwdriver into the idle adjustment screw Fig 35 Turn the idle speed screw clockwise 1 8 of a turn at a time as needed until the engine idles smoothly 3 If the engine appears to be idling too fast turn the idle speed screw counterclockwise 1 8 of
61. k the release button into the 90 hole Fig 5 ASSEMBLY INSTRUCTIONS REMOVE AND INSTALL THE CUTTING ATTACHMENT SHIELD WARNING The cutting attachment Cutting shield should NOT be installed when Attachment operating the unit with a blade Remove the cutting attachment shield before removing or installing the blade Remove the cutting attachment shield when using the unit as a brushcutter Remove the cutting attachment shield from the shield mount by removing the three 3 screws with a flat blade screwdriver Fig 6 Store parts for future use Fig 6 INSTALL THE HARNESS WARNING Always use the shoulder harness when using the cutting blade to avoid serious personal injury 1 Push the strap through the center of the buckle Pull the strap over the cross bar and down through the slot in the buckle Fig 7 3 Put the harness on over head and onto shoulder Snap it on to the support fitting Fig 8 4 Adjust length to fit the operator s size Pull tab to lengthen pull strap to shorten Fig 9 N Support n Fitting Fig 8 Fig 9 Install the cutting attachment shield when using the unit as a grass trimmer WARNING To avoid serious personal injury the cutting attachment shield MUST be in place at all times while operating the unit as a grass trimmer Install the cutting attachment shield on the shield mount by inserting the three 3 screws into the shield mount Tighten secur
62. la cuchilla puede ocurrir si la cuchilla se tropieza se traba o se atora Es m s posible que esto ocurra en reas donde es dif cil ver el material que est cortando Para establecer un procedimiento r tmico de corte e Fije los pies con firmeza c modamente aparte e Lleve el motor a plena regulaci n antes de penetrar el material a cortar La cuchilla tiene su m xima capacidad de corte a plena regulaci n y tambi n es menos probable que se adhiera se trabe o cause el impulso de la cuchilla lo cual puede causar graves lesiones personales al operador o a otros e Corte girando la parte superior de su cuerpo de izquierda a derecha e Suelte siempre el gatillo del regulador y espere que el motor vuelva a marcha lenta cuando no est cortando e Cuando termine la labor desabroche siempre la unidad antes de quitarse el arn s e Mueva la unidad en la direcci n opuesta en que gira la cuchilla con lo cual lograr una mejor acci n de corte e Avance al rea siguiente a cortar despu s de la maniobra de retorno y vuelva a fijar los pies e La cuchilla de corte est dise ada con un segundo borde de corte el cual puede ser utilizado retirando la cuchilla d ndola vuelta y volviendo a instalarla Para reducir la posibilidad de que se enrede material en la cuchilla siga estos pasos ADVERTENCIA La cuchilla contin a girando luego de apagar el motor La cuchilla en deslizamiento puede causarle graves cortes si lo toca en
63. llenar la unidad de combustible NOTA No hay necesidad de encender la unidad El Control de Encendido y Apagado est en la posici n Encendido I en todo momento Fig 18 3 Oprima y suelte completamente la pera del cebador 10 veces lentamente Se deber ver un poco de combustible en el cebador Fig 19 Si no puede ver el combustible en el cebador oprimalo y su ltelo tantas veces como sea necesario hasta que vea combustible en el mismo 4 Coloque la palanca del obturador en Posici n 1 Fig 19 5 Ag chese en posici n de arranque Fig 9 Oprima la traba del regulador hacia adentro y apriete la palanca de control del regulador Hale el cord n de arranque 5 veces 6 Coloque la palanca del obturador en Posici n 2 Fig 19 7 Mientras que exprime el control de v lvula reguladora tire de la cuerda del arrancador en rgicamente 3 a 5 veces de encender el motor 8 Mantenga oprimido el regulador y deje que el motor se caliente durante 30 a 60 segundos 9 Mientras oprime el control del regulador coloque la palanca del obturador en la Posici n 3 Fig 19 y contin e calentando el motor durante 60 segundos m s Se puede usar la unidad durante este tiempo NOTA La unidad se ha calentado debidamente cuando el motor acelera sin titubear SI El motor titubea regrese la palanca del obturador a la Posici n 2 Fig 19 y siga calent ndolo SI El motor no arranca regrese al paso 3 SI El motor no arranca de
64. nal Accessory Please refer to the Electric Starter or Power Start Bit operator s manual for proper use of this feature Items Sold Separately Please refer to page 5 of this manual about purchasing these accessories STARTING INSTRUCTIONS 1 Mix fuel with oil Fill fuel tank with fuel oil mixture See Oil and Fuel Mixing Instructions 2 Fill the fuel tank with fresh clean fuel mix Refer to Fueling the Unit NOTE There is no need to turn the unit on The On Off Control is in the ON 1 position at all times Fig 19 3 Fully press and release the primer bulb 10 times slowly Some amount of fuel should be visible in the primer bulb Fig 19 If fuel cannot be seen in the bulb press and release the bulb until fuel is visible 4 Move the choke lever to Position 1 Fig 19 5 Crouch in the starting position Fig 20 Place the electric starter or power start bit into the back of the unit Refer to the Operation section of the Electric Starter or Power Start Bit operator s manual 6 Squeeze the throttle control lever Press and hold the electric starter or drill ON I button for 2 seconds 7 Move the choke lever to Position 2 Fig 19 8 Squeeze the throttle control lever press and hold the electric starter or drill ON I button for 2 second intervals until the unit starts 9 Continue to squeeze the throttle control remove the electric starter or drill from the unit and allow the engine to warm up for 30 to 60 seconds
65. nformation e Do not overreach Always keep proper footing and balance Take extra care when working with on steep available at the time of printing We reserve the right to make changes at any time without notice slopes or inclines Copyright 2011 MTD SOUTHWEST INC All Rights Reserved e Always hold the unit with both hands when operating Keep a firm grip on the handle e Keep hands face and feet at a distance from all moving parts e Do not touch the engine or muffler These parts get extremely hot from operation They remain hot for a short time after turning off the unit e Do not operate the engine faster than the speed needed for the job Do not run the engine at high speed when the unit is not in use SERVICE INFORMATION Always stop the engine when work is delayed or wien walking trom one location to another e f striking or becomes entangled with a foreign object stop the engine immediately and check for DO NOT RETURN THIS UNIT TO THE RETAILER PROOF OF PURCHASE WILL BE REQUIRED damage Do not operate before repairing damage Do not operate the unit with loose or damaged parts FOR WARRANTY SERVICE e Stop and switch the engine to off for maintenance or repair For assistance regarding the assembly controls operation or maintenance of the unit please call the e Use only original equipment manufacturer replacement parts and accessories for this unit These are Customer Support Department at 1 800 828 5500 in the United States or 1 800
66. nn Aaa nn AH720 Cultivador sisi cere estes 2 12 A AA dees EE te GC720 Recortador de bordes de c sped 1 cent teens LE720 Sierra AS POSTS se 42 24 0 drench te aoe Bek Halas ea nana ened Bie RAD EN tie wee aes PS720 Recortador desejeirecto sisas cota fern nae neta be A wate mes SS725 T rbosoplador is irns run 22 irren in arena TB720 NO use este accesorio con un producto el ctrico Remoci n del accesorio de corte u otros accesorios 1 Gire la perilla en sentido antihorario para aflojarla Fig 5 2 Opima y sostenga el bot n de desconexi n Fig 3 3 Mientras sostiene el bastidor del eje superior con firmeza tire del accesorio de corte o accesorio en l nea recta fuera del acoplador EZ LinkTM Fig 4 Instalaci n del accesorio de corte u otros accesorios NOTA Para facilitar la instalaci n o remoci n de los accesorios coloque la unidad sobre el suelo o sobre un banco de trabajo 1 Gire la perilla en sentido antihorario para aflojarla Fig 5 2 Mientras sostiene el accesorio con firmeza emp jelo en l nea recta en el acoplador EZ Link Fig 4 NOTA La alineaci n del bot n de desconexi n con el hueco de gu a facilitar la instalaci n Fig 3 EZ Link Acoplador N O Bot n de desconexi n Hueco de gu a Fig 3 Orificio primario Bastidor del Bastidor del 3 Gire la perilla en sentido horario para ajustarla Fig 5 Re Pare En eje inferior i ig Para rec
67. o m s peque o posible Fig 31 de 6 pulgadas Man 708 N ajustadas en la direcci n indicada en el carrete interior indicada el accesorio de corte no funcionar en forma correcta fijaci n Fig 32 la bobina exterior y coloque el carrete interior con el resorte dentro de la bobina exterior Fig 33 Empuje el carrete interior y la bobina exterior entre s Mientras sostiene el carrete interior y la bobina exterior tome los extremos y hale con firmeza para soltar la l nea de las ranuras de fijaci n de la bobina antes de volver a ensamblar el accesorio de corte tope gir ndolo en sentido horario Ajuste bien Sostenga la bobina exterior con una mano y desenrosque el bot n de tope en sentido antihorario Fig 25 Inspeccione el perno dentro del bot n de tope para verificar que se mueva con libertad Cambie el bot n de tope si est da ado Saque el carrete interior viejo de la bobina exterior Fig 25 Saque el resorte del carrete interior viejo Fig 25 Coloque el resorte en el carrete interior nuevo NOTA El resorte debe estar ensamblado en el carrete interior antes de volver a instalar el accesorio 5 6 de corte Inserte los extremos de la l nea en los ojalillos de la bobina exterior Fig 33 Coloque el nuevo carrete interior dentro de la bobina exterior Empuje el carrete interior y la bobina exterior entre s Mientras sostiene el carrete interior y la bobina exterior
68. ons FUELING THE UNIT 1 Turn unit on its side with the fuel cap facing up and remove the fuel cap 2 Place the gas container s spout into the fill hole on the fuel tank and fill the tank NOTE Do not overfill the tank 3 Wipe up any gasoline that may have spilled 4 Reinstall the fuel cap 5 Move the unit at least 30 ft 9 1 m from the fueling source and site before starting the engine STARTING AND STOPPING INSTRUCTIONS OFF 0 WARNING Operate this unit in a well ventilated outdoor area Carbon monoxide exhaust fumes can be lethal in a confined area WARNING Avoid accidental starting Make sure you are in the starting position when pulling the starter rope Fig 9 To avoid serious injury the operator and unit must be in a stable position while starting Throttle Control STARTING INSTRUCTIONS 1 Mix fuel with oil Fill fuel tank with fuel oil mixture See Oil and Fuel Mixing Instructions 2 Fill the fuel tank with fresh clean fuel mix Refer to Fueling the Unit NOTE There is no need to turn the unit on The On Off Control is in the ON 1 position at all times Fig 18 3 Fully press and release the primer bulb 10 times slowly Some amount dE of fuel should be visible in the primer bulb and fuel lines Fig 19 If fuel can not be seen in the bulb press and release the bulb until fuel is visible 4 Place the choke lever in Position 1 Fig 19 5 Crouch in the starting position Fig 20
69. or products sold or exported outside of the United States of America its possessions and territories except those sold through Troy Bilt s authorized channels of export distribution Troy Bilt reserves the right to change or improve the design of any Troy Bilt Product without assuming any obligation to modify any product previously manufactured No implied warranty including any implied warranty of merchantability or fitness for a particular purpose applies after the applicable period of express written warranty above as to the parts as identified No other express warranty or guaranty whether written or oral except as mentioned above given by any person or entity including a dealer or retailer with respect to any product shall bind Troy Bilt During the period of the Warranty the exclusive remedy is repair or replacement of the product as set forth above Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you The provisions as set forth in this Warranty provide the sole and exclusive remedy arising from the sales Troy Bilt shall not be liable for incidental or consequential loss or damages including without limitation expenses incurred for substitute or replacement lawn care services for transportation or for related expenses or for rental expenses to temporarily replace a warranted product Some states do not allow limitations on how long an implied warranty lasts so the a
70. ortar bordes mientras usa el accesorio de corte de cabeza de l nea o con modelos EZ Link trabe el bot n de desconexi n en el orificio lateral Orificio lateral de 90 Fig 5 INSTRUCCIONES DE ENSAMBLE REMOCI N E INSTALACI N DEL PROTECTOR ACCESORIO DE CORTE ADVERTENCIA El protector accesorio Protector lt lt Tornillos 3 de corte NO debe estar instalado cuando ett use la unidad con una cuchilla Saque el protector accesorio de corte antes de sacar o instalar la cuchilla Bastidor del engranaje Saque el protector accesorio de corte cuando Y y gt ee use la unidad como cortador de malezas LA Saque el protector accesorio de corte del montaje Ty del protector retirando los tres 3 tornillos con un Montaje del destornillador de v stago plano Fig 6 Guarde las p az piezas para usarlas en el futuro INSTALACION DEL ARNES 1 Pase la correa a trav s del centro de la hebilla 2 Pase la correa sobre la barra transversal y hacia abajo a trav s de la ranura de la hebilla Fig 7 3 Coloque el arn s por encima de su cabeza y sobre su hombro Abroche en el adaptador de apoyo Fig 8 4 Ajuste la longitud de acuerdo a la medida del operador Hale de la orejeta para alargarlo y hale de la correa para acortarlo Fig 9 Adaptador de apoyo vd Fig 8 Fig 9 Instale el protector accesorio de corte cuando use la unidad como recortador de c s
71. otras personas sufran lesiones personales Siga siempre las precauciones de seguridad para reducir el riesgo de incendio descarga el ctrica y lesiones personales NOTA Le ofrece informaci n o instrucciones que son esenciales para la operaci n o mantenimiento del equipo e COMBUSTIBLE SIN PLOMO Use siempre combustible limpio nuevo y sin plomo Lea el manual del operador y siga todas las advertencias e instrucciones de seguridad De no hacerlo el operador y o los espectadores pueden sufrir graves lesiones SI TIENE PREGUNTAS LLAME AL 1 800 828 5500 EN EE UU O AL 1 800 668 1238 EN CANADA IMPORTANTE INFORMACION DE SEGURIDAD e NO UTILICE COMBUSTIBLE E85 EN ESTA UNIDAD ADVERTENCIA Se ha demostrado que el combustible que contiene m s del _ 5 E Has 2 gt PROPOSICI N 65 DEL ESTADO DE CALIFORNIA 10 de etanol probablemente ocasionar da os al motor y anular la garant a ADVERTENCIA Los gases de escape algunos de sus componentes y determinados productos terminados contienen o emiten productos qu micos de los que el estado de e CONTROL DE ENCENDIDO Y APAGADO California tiene conocimiento provocan c ncer malformaciones cong nitas u otros da os ENCENDIDO ARRANQUE MARCHA al sistema reproductor L vese las manos despu s de manipularlo e CONTROL DE ENCENDIDO Y APAGADO LEA TODAS LAS INSTRUCCIONES ANTES DE OPERAR LA UNIDAD APAGADO o PARADO ADVERTENCIA Se deben seguir las siguientes reglas de seguridad cuando use la un
72. parejas y NOTA Si no bobina la l nea en la direcci n 12 Inserte los extremos de la l nea en las dos ranuras de 13 Inserte los extremos de la l nea a trav s de los ojalillos de NOTA El resorte debe estar ensamblado en el carrete interior 14 Sostenga el carrete interior en su lugar e instale el bot n de INSTALACI N DE UN CARRETE PREBOBINADO 1 2 3 4 Bobine las l neas en capas parejas y ajustadas Inserte el extremo de la l nea en el orificio nueva l nea de corte enl cela en dos longitudes iguales Inserte cada extremo de la l nea a trav s de uno de los dos orificios del carrete interior Fig 29 Pase la l nea a trav s del carrete interior de modo que el lazo sea lo m s peque o posible cuando instale la linea de corte en la unidad La l nea puede no soltarse en forma adecuada si es demasiado larga sobre el carrete Fig 30 Bobine la l nea en la direcci n indicada en el carrete interior Coloque su dedo ndice entre las dos l neas para evitar que se superpongan No superponga los extremos de la l nea Proceda al paso 11 Tome aproximadamente 3 m 10 pies de nueva l nea de corte Inserte un extremo de la l nea a trav s de uno de los orificios del carrete interior Fig 31 Pase la l nea a trav s del carrete interior hasta que queden s lo 4 pulgadas fuera abierto del carrete interior y hale de la l nea en forma ajustada a fin de que el lazo sea l
73. ped Instale el protector accesorio de corte en el montaje del protector insertando 3 tornillos en el montaje del protector Ajuste bien con un destornillador de v stago plano Fig 6 REMOCI N DEL ACCESORIO DE CORTE E INSTALACI N DE LA CUCHILLA DE CORTE NOTA Para facilitar la remoci n o la instalaci n de la cuchilla de corte coloque la unidad sobre el suelo o sobre un banco de trabajo ADVERTENCIA El bastidor del engranaje se calienta mucho con el uso y puede causar lesiones al operador Cuando la unidad se apaga permanece caliente durante un rato No toque el bastidor del engranaje hasta que se haya enfriado Lea Remoci n e Instalaci n del Protector Accesorio de Corte Remoci n del accesorio de corte 1 Alinee el orificio del buje del eje con la ranura de la varilla de cierre e inserte la varilla de cierre en el orificio del buje del eje Fig 10 2 Sostenga la varilla de cierre en su lugar junto al brazo de la unidad Fig 11 3 Mientras sostiene la varilla de cierre saque el accesorio de corte girando en sentido horario hacia afuera del eje de salida Fig 12 Guarde el accesorio de corte para su uso futuro NOTA El ret n de la cuchilla debajo del accesorio de corte se utilizar cuando instale la cuchilla de corte Eje de salida Buje del eje de salida Ranura de la varilla de cierre Varilla de cierre y Accesorio de corte Ranura de la varilla de cierre 10
74. product and has not been subject to misuse abuse commercial use neglect accident improper maintenance alteration vandalism theft fire water or damage because of other peril or natural disaster Damage resulting from the installation or use of any accessory or attachment not approved by Troy Bilt for use with the product s covered by this manual will void your warranty as to any resulting damage This warranty is limited to ninety 90 days from the date of original retail purchase for any Troy Bilt product that is used for rental or commercial purposes or any other income producing purpose HOW TO OBTAIN SERVICE Warranty service is available WITH PROOF OF PURCHASE THROUGH YOUR LOCAL AUTHORIZED SERVICE DEALER To locate the dealer in your area please check for a listing in the Yellow Pages or contact the Customer Service Department of Troy Bilt by calling 1 800 828 5500 or writing to P O Box 361131 Cleveland OH 44136 0019 or if in Canada call 1 800 668 1238 No product returned directly to the factory will be accepted unless prior written permission has been extended by the Customer Service Department of Troy Bilt This limited warranty does not provide coverage in the following cases A Tune ups Spark Plugs Carburetor Adjustments Filters B Wear items Bump Knobs Outer Spools Cutting Line Inner Reels Starter Pulley Starter Ropes Drive Belts Saw Chains Guide Bars Cultivator Tines C Troy Bilt does not extend any warranty f
75. s stop the engine and allow it to cool before filling the fuel tank Never remove the fuel tank cap or add fuel when the engine is hot Always loosen the fuel tank cap slowly to relieve any pressure in the tank before fueling Do not smoke e Always add fuel in a clean well ventilated outdoor area where there are no sparks or flames Do not smoke e Never operate the unit without the fuel cap securely in place e Avoid creating a source of ignition for spilled fuel Wipe up any spilled fuel from the unit immediately before starting the engine Move the unit at least 30 feet 9 1 m from the fueling source and site before starting the engine Do not smoke e Keep these instructions Refer to them often and use them to instruct other users If loaning someone this unit also loan them these instructions SAVE THESE INSTRUCTIONS e SAFETY AND INTERNATIONAL SYMBOLS This operator s manual describes safety and international symbols and pictographs that may appear on this product Read the operator s manual for complete safety assembly operating maintenance and repair information YMBOL e SAFETY ALERT SYMBOL Indicates danger warning or caution May be used in conjunction with other symbols or pictographs e READ OPERATOR S MANUAL WARNING Read the operator s manual s and follow all warnings and safety instructions Failure to do so can result in serious injury to the operator and or bystanders e WEAR EYE AND HEARING PROTECTION
76. sar durante este paso NOTA La unidad se ha calentado debidamente cuando el motor acelera sin fallar SI el motor funciona con fallas vuelva a colocar la palanca del obturador en la Posici n 2 Fig 19 y contin e calentando el motor SI el motor no arranca regrese al paso 3 SI el motor no arranca despu s de unos cuantos intentos coloque la palanca del obturador en la Posici n 3 y oprima el gatillo Apriete y mantenga apretado el bot n de ENCENDIDO I del arrancador el ctrico o taladro a intervalos de 2 segundos hasta que la unidad arranque SI EST CALIENTE Si el motor ya est caliente arranque la unidad con la palanca azul del obturador en la Posici n 2 Despu s que la unidad arranque mueva la palanca azul del obturador a la Posici n 3 INSTRUCCIONES DE APAGADO 1 Saque la mano del control del regulador Deje enfriar el motor en marcha en vac o 2 Oprima y mantenga oprimido el control de encendido y apagado en la posici n de APAGADO 0 hasta que el motor se detenga por completo Fig 18 INSTRUCCIONES DE OPERACI N COMO SOSTENER EL RECORTADOR ADVERTENCIA Siempre ojo del desgaste el o r protecci n del pie y del cuerpo para reducir el riesgo de lesi n al funcionar esta unidad Antes de operar esta unidad p rese en posici n de operaci n Fig 21 Verifique lo siguiente e El operador tiene protecci n ocular y ropa adecuada e El brazo derecho est levemente doblado y la mano est
77. sea necesario hasta que el motor funcione en marcha en vac o sin inconvenientes Fig 35 NOTA Las p as no deben girar cuando el motor est en m nima 3 Silas p as giran cuando el motor est en m nima gire el tornillo de marcha lenta en sentido antihorario 1 8 de vuelta por vez seg n sea necesario para reducir la marcha lenta El control de la mezcla de combustible la limpieza del filtro de aire y el ajuste del tornillo de marcha lenta deben resolver la mayor a de los problemas del motor De no ser as y si e El motor no funciona en m nima e El motor fluct a o se para al acelerar e Existe una p rdida de fuerza motriz Lleve el carburador a un proveedor de servicio autorizado para que lo ajuste CAMBIO DE LA BUJIA DE ENCENDIDO 1 Apague el motor y espere que se enfr e Tome el alambre de la buj a con firmeza y s quelo de la buj a de encendido 2 Limpie alrededor de la buj a de encendido Saque la buj a de encendido de la cabeza del cilindro girando una llave de casquillo de 16 mm 5 8 de pulgada en sentido antihorario PRECAUCION No limpie con chorro de arena ni raspe ni limpie los electrodos El motor podr a da arse si penetran peque as part culas en el cilindro 3 Inspeccione la buj a Si la buj a est rajada corro da o sucia c mbiela por una buj a 753 06193 Champion RDJ7J o una equivalente 4 Use un calibrador de hoja para ajustar la abertura de la buj a a 0 025 p
78. sosteniendo el mango del eje e El brazo izquierdo est recto y la mano sostiene la manija en y e La unidad est debajo del nivel de la cintura e El accesorio de corte est paralelo al suelo y hace f cil contacto con la vegetaci n que va a ser cortada sin que el operador tenga que inclinarse CONSEJOS PARA OBTENER MEJORES RESULTADOS AL RECORTAR e El ngulo correcto para ubicar el accesorio de corte es paralelo al suelo e No fuerce el accesorio de corte Permita que la punta de la l nea realice el corte en especial a lo largo de paredes Si corta con m s de la punta reducir la eficacia del corte y puede sobrecargar el motor e Corte c sped de m s de 200 mm 8 pulgadas trabajando de arriba hacia abajo en peque os incrementos para evitar el desgaste prematuro de la l nea y el arrastre del motor e Corte de derecha a izquierda siempre que sea posible Cortar hacia la izquierda mejora la eficiencia de la unidad Los recortes salen arrojados en sentido contrario al operador e Mueva lentamente el recortador dentro y fuera del rea de corte a la altura deseada Realice movimientos ya sea de adelante hacia atr s y viceversa o de lado a lado El corte en longitudes m s cortas produce mejores resultados e Recorte nicamente cuando el pasto y las hierbas est n secas e La vida de su l nea de corte depende de e Seguir todas las t cnicas de corte indicadas anteriormente e El tipo de vegetaci n que corte e El lu
79. spu s de 2 intentos coloque la palanca del obturador en la Posici n 3 y oprima el control del regulador Tire de la cuerda de arranque 3 a 8 veces en un movimiento controlado El motor debe arrancar Si no lo hace repita el procedimiento SI SE CALIENTA El motor ya est caliente regrese al paso 6 INSTRUCCIONES DE APAGADO 1 Saque la mano del control del regulador Deje enfriar el motor en marcha en vac o 2 Oprima y mantenga oprimido el control de encendido y apagado en la posici n de APAGADO O hasta que el motor se detenga por completo Fig 18 Cuerda de arranque 11 COMO ARRANCAR LA UNIDAD UTILIZANDO EL ARRANCADOR ELECTRICO O EL ACCESORIO DE ARRANQUE ELECTRICO OPCIONAL NOTA Esta unidad puede utilizar un arrancador el ctrico o un accesorio de arranque opcional Power Start Bit Para informarse sobre el uso adecuado de estos sistemas consulte el manual del operador del arrancador el ctrico o accesorio de opcional Power Start Bit Se vende por separado En la p gina 13 de este manual encontrar la informaci n necesaria para comprar estos accesorios INSTRUCCIONES DE ARRANQUE 1 Mezcle la gasolina con aceite Llene el tanque de combustible con una mezcla de combustible aceite Vea las instrucciones sobre c mo mezclar el aceite y el combustible 2 Llene el tanque de combustible con gasolina limpia y fresca Consulte C mo llenar la unidad de combustible NOTA No hay necesidad de arrancar l
80. tep 11 For Use with Single Line ONLY For Use with SplitLine TM or Single Line SplitLine Installation 8 Take approximately 9 feet 3 m of new trimming line Insert one end of the line through one of the two holes in the inner reel Fig 31 Pull the line through the inner reel until only about 4 inches is left out 9 Insert the end of the line into the open hole in the inner reel and pull the line tight to make the loop as small as possible Fig 31 10 Before winding split the line back about 6 inches 11 Wind the line in tight even layers in the direction indicated on the inner ree NOTE Failure to wind the line in the direction indicated will cause the cutting attachment to operate incorrectly 12 Insert the ends of the line into the two holding slots Fig 32 13 Insert the ends of the line through the eyelets in the outer spool and place inner reel with spring inside the outer spool Fig 33 Push the inner reel and outer spool together While holding the inner reel and outer spool grasp the ends and pull firmly to release the line from the holding slots in the reel NOTE The spring must be assembled on the inner reel before reassembling the cutting attachment 14 Hold the inner reel in place and install the bump knob by turning counterclockwise Tighten securely INSTALLING A PREWOUND REEL 1 Hold the outer spool with one hand and unscrew the bump knob clockwise Fig 25 Inspect the bolt inside the
81. that the unit cannot start Perform these required maintenance procedures at the frequency stated in the table These procedures should also be a part of any seasonal tune up NOTE Some maintenance procedures may require special tools or skills If you are unsure about these procedures take your unit to any non road engine repair establishment individual or authorized service dealer NOTE Maintenance replacement or repair of the emission control devices and system may be performed by any non road engine repair establishment individual or authorized service dealer NOTE Please read the California EPA statement that came with the unit for a complete listing of terms and coverage for the emissions control devices such as the spark arrestor muffler carburetor etc FREQUENCY WAINTEWANGEREGUIED SEE LINE INSTALLATION This section covers both SplitLine and standard single line installation Always use original equipment manufacturer 0 105 in 2 67 mm replacement line Other types of line may make the engine overheat or fail WARNING Never use metal reinforced line wire chain or rope These can break off and become dangerous projectiles There are two methods to replace the trimming line e Wind the inner reel with new line e Install a prewound inner reel Winding the Existing Inner Reel 1 Hold the outer spool with one hand and unscrew the Bump Knob clockwise Fig 25 Inspect the bolt inside the bump knob to m
82. ud correcta de l nea Saque el carrete interior de la bobina exterior Saque el resorte del carrete Use un pa o limpio para Verifique el desgaste de los Sostenga la bobina exterior con una mano y desenrosque el bot n de tope en sentido antihorario Fig 25 Inspeccione el perno de adentro del bot n de tope para verificar que se mueva con libertad Cambie el bot n de tope si est da ado Fig 25 i i i Dientes interior Fig 25 de posici n limpiar el carrete interior el resorte el eje y la bobina exterior Fig 26 dientes de posici n del carrete interior y bobina exterior Fig 27 Si es necesario saque la rebaba o cambie el carrete y la bobina puede usarse con el carrete interior con los orificios ranurados La l nea individual puede usarse en cualquier tipo de carrete interior Use la Figura 28 para identificar el carrete interior que usted tiene 10 OSEN cuando instale la l nea de corte en la unidad La l nea puede no soltarse en forma adecuada si es demasiado larga Instalaci n de la l nea individual ranurados Lea la instalaci n de la l nea SplitLine en el Para usar S LO Para usar con SplitLine paso 8 con l nea individual o l nea individual 6 Tome aproximadamente 6 m 20 pies de NOTA Use siempre la longitud correcta de l nea Instalaci n de la l nea SplitLine 8 10 Antes de bobinar separe la l nea alrededor 11 Bobine la l nea en capas
83. ue la unidad en una superficie plana Llene el tanque de combustible Protector del cabezal SI el motor no arranca despu s de 2 intentos de corte mueva la palanca del obturador hasta de 2 tiempos 1 gal n de gasolina sin plomo NOTA No lo mezcle directamente en el la posici n 3 y tire de la cuerda de arranque hasta que arranque el motor SI el motor todav a no arranca consulte el manual del operador para obtener informaci n adicional sobre c mo solucionar problemas en el arranque Palanca del obturador v WA Rd y I 5X QUES 9 10 D 3 5 X da APRIETE y MANTENGA Tire de la cuerda Mueva la palanca Tire de la cuerda Mantenga apretado Mantenga apretado APRETADO el control de arranque 5 veces del obturador hasta de arranque fuertemente el control del regulador el control del regulador del regulador en TODOS la Posici n 2 y oprima de 3 a 5 veces para arrancar Coloque la palanca Haga funcionar la unidad los pasos que se describen el control del regulador el motor Haga funcionar del obturador durante 60 segundos m s a continuaci n la unidad entre 30 y 60 en la Posici n 3 para completar segundos para calentar el calentamiento el motor Se puede usar la unidad durante este tiempo tanque de combustible C mo arrancar la unidad Palanca del obturador Col quese en la posici n de arranque IMPORTANTE LEA BIEN EL MANUAL DEL OPERADOR Y AL OPERAR LA UNIDAD SIGA LAS INSTRUCCIONES PARA EL F
84. ulgadas 0 635 mm Fig 36 5 Instale la buj a en la culata del motor Apriete la buj a en el sentido de las agujas del reloj con una llave de buj a de 5 8 hasta ajustarla NOTA Si usa una llave de torsi n ajuste a 12 3 13 5 Nom 110 120 pulg olibras No ajuste demasiado 0 635 mm FO 6 Vuelva a conectar el cable de la buj a de encendido Fig 36 13 LIMPIEZA Y ALMACENAMIENTO RESOLUCION DE PROBLEMAS LIMPIEZA CAUSA ACCION EL MOTOR NO ARRANCA ADVERTENCIA Para evitar graves lesiones personales apague siempre su recortador y espere que se enfr e antes de limpiarlo o realizar cualquier tipo de mantenimiento El tanque de combustible est vac o Remplissez le de carburant bien m lang Use un cepillo peque o para limpiar la parte exterior de la unidad No use detergentes fuertes Los La bombilla de cebado no fue oprimida lo suficiente Oprima la pora del cebador 10 veces o hasta que se vea limpiadores dom sticos que contienen aceites arom ticos como pino y lim n y con solventes como el queroseno pueden da ar el bastidor de pl stico y la manija Seque toda la humedad con un pa o Amao cs inneke Utilisez la proc dure de d marrage suave El combustible est viejo m s de 30 d as y o mal Drene el tanque de combustible y eche combustible ALMACENAMIENTO mezclado fresco mezclado adecuadamente e No guarde nunca la unidad con combustible en el tanque donde los vapores puedan llegar a una La buj a de enc
85. un m todo de arranque alternativo que para muchas personas resulta m s sencillo de usar que tirar la cuerda de arranque Comun quese con el distribuidor local o llame al 1 800 828 5500 para obtener mayor informaci n Tambi n puede encontrar informaci n en www troybilt com Interruptor de y Encendido Apagado Calcoman a Tapa de combustible Quite la tapa del brazo Empuje el accesorio de corte dentro del acoplador Para apretar haga girar la perilla en sentido de las agujas del reloj Coloque el J manejar entre las abrazaderas superiores y medios deslice los 4 tornillos a trav s de las abrazaderas y colocar el conjunto en la abrazadera inferior Inicio de los tornillos a continuaci n asegurar la flecha l nea blanca en los toques calcoman a de la abrazadera La posici n de la J manejar a la ubicaci n que ofrece el mejor agarre y apriete los tornillos en forma pareja hasta que el J mango Control del regulador D ou l E En D uy DDN Ensamblado de la unidad C mo arrancar la unidad NECESARIAS e Destornillador Phillips Necesita ayuda Llame al 1 800 828 5500 1 gal n 3 2 onzas NO ARRANC Oprima 10 veces la pera Repita estas instrucciones del cebador o bien hasta que se vea el combustible Coloque la palanca del obturador en la Posici n 1 Mezcle bien en un recipiente de combustible aparte 3 2 onzas fluidas de aceite para motor Coloq

Download Pdf Manuals

image

Related Search

Related Contents

BoConcept Model 4200 Assembly Instruction  GUI interfacev36 - Civil & Environmental Engineering  Toro EZ-Flo Plus Series 1" MxM Thread-Flow Installation Manual  スカパー ! HD対応チューナー CS-HD300 取扱説明書  E120693 - Starcom Systems  TAPM V4. User Manual. - CSIRO Marine and Atmospheric Research  UNDER /MOINS DE POINTS TS  Tripp Lite Minicom Smart 232  H35B Handheld Device  

Copyright © All rights reserved.
Failed to retrieve file