USB Interface Kit P/N 71208792 Instruction Manual Paquete de
Contents
1. Found New Hardware Wizard Install Hardware Device Drivers gt A device driver is a software program that enables a hardware device to work with an S operating system This wizard will complete the installation for this device e USB Serial A device driver is a software program that makes a hardware device work Windows needs driver files for your new device To locate driver files and complete the installation click Next What do you wantthe wizard to do Search for a suitable driver for my device recommended C Display a list of the known drivers for this device so that can choose a specific driver Back Cancel SCREEN 2 EN 6 USB Interface Kit Found New Hardware Wizard E Locate Driver Files ey SS Where do you want Windows to search for driver files Search for driver files for the following hardware device a USB lt gt Serial The wizard searches for suitable drivers in its driver database on your computer and in any of the following optional search locations that you specify To startthe search click Next Ifyou are searching on a floppy disk or CD ROM drive insert the floppy disk or CD before clicking Next Optional search locations Floppy disk drives Iv CD ROM drives Specify a location Microsoft Windows Update Back Cancel SCREEN 3 5 Two drivers will be installed in back to back sequence Therefore you ll repeat the steps in screen 1 to scr2. Aparecer la ventana Asistente para Encontrar Hardware Nuevo Las siguientes fotos de pantalla son ejemplos de la instalaci n utilizando Windows 20006 Otros sistemas operativos de Microsoft Windows pueden mostrar una ventana similar con una vista ligeramente diferente El Asistente de Hardware en todas las versiones de Windows lo guiar a trav s de la instalaci n de los dos controladores necesarios localizados en el CD con los Paquete de interfaz USB 4 pasos descritos a continuaci n Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install a device driver for a hardware device To continue click Next EN 5 PANTALLA 1 lt Back Cancel Haga clic en el bot n Siguiente y se visualizara la pantalla 2 Haga clic en Siguiente para moverse a la pantalla 3 y marque la casilla CD ROM antes de hacer clic en Siguiente Found New Hardware Wizard I Install Hardware Device Drivers device driver is a software program that enables a hardware device to work with an operating system This wizard will complete the installation for this device e USB Serial A device driver is a software program that makes a hardware device work Windows needs driver files for your new device To locate driver files and complete the installation click Next What do you wantthe wizard to do Search for a suitable driver for my devic
3. S CT 2 Schalentr ger 2 Abbildung 1B Zugluftschutz ii Glasplatten LA Schale Abdeckungsschrauben 2 Abbildung 1C 1 USB Schnittstellenoption DE 3 W hrend die Stromzufuhr zur Waage unterbrochen ist alle installierten Zugluftschutzvorrichtungen oder Zugluftschutz Glasplatten die Schale den Schalentr ger und eventuell angebrachte Windringe oder Adapterringe ausbauen Gr en und Formen variieren um die EMV Platte oben auf der Waage vollst ndig freizulegen Die zwei Schrauben und die EMV Platte ausbauen HINWEIS F r bestimmte Modelle mit einem rechteckigen Windring werden 4 Stifte zur Ausrichtung der EMV Platte mitgeliefert Bitte darauf achten dass diese Stifte nicht verloren gehen Diese sind mit F front vorne oder B back hinten so markiert dass die Markierungen nach innen weisen achten Sie auf die entsprechenden Positionen f r den Fall dass sie sich l sen und wieder angebracht werden m ssen Das Oberteil vom unteren Geh use abmontieren je nach Modell a Modelle mit kleinem Rahmen Die 4 F e ausbauen dann die 4 Schrauben in den ffnungen die jetzt nach dem Ausbauen der F e freiliegen entfernen HINWEIS Beim Ausbauen der F e die Waage nicht auf den Kopf stellen auf die Baugruppe mit W gezelle Kegel Wenn dies jedoch unvermeidlich ist die Kegelschutzabdeckung aus Kunststoff aus dem Satz ber die Baugruppe aus W gezelle und Kegel
4. Route the PCB cable towards the left side of the bottom housing Re assemble the balance in the reverse order of the disassembly process being careful not to pinch any cables within or between the top and bottom housing 3 EN 4 USB Interface Kit Cone Cover for small frame models COM2 Cover Plate Figure 2A Figure 2B USB PCB PCB Cable Figure 2C Figure 2D INSTALLATION OF SOFTWARE After installing the hardware install the USB driver software contained in the kit CD 3 1 Software Installation 1 2 Insert the supplied CD into the CD ROM drive of the computer Connect the balance to the computer s USB port through the USB cable supplied Found New Hardware Wizard window will come up The following screen shots are examples of the installation using Windows 2000 Other Mircrosoft Windows operating systems may show a similar window with a slightly different look Hardware Wizard in all versions of Windows will guide you through the installation of the necessary 2 drivers located on the CD with steps described below USB Interface Kit EN 5 F New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install a device driver for a hardware device To continue click Next lt Back Cancel SCREEN 1 4 Click Next and screen 2 will be displayed Click Next to move to screen 3 and check CD ROM Drive before clicking Next
5. Serial Bus Este paquete de interfaz utiliza una clase de conversi n USB a serial que permite usar un puerto USB como si fuera un puerto serial RS232 tambi n conocido como puerto COM virtual Lea completamente este manual antes de instalar y trabajar con su dispositivo LEA TODAS LAS ADVERTENCIAS DE SEGURIDAD ANTES DE INSTALAR HACER CONEXIONES O DAR SERVICIO A LA BALANZA LA FALTA DE CUMPLIMIENTO DE ESTAS ADVERTENCIAS PODRIA RESULTAR EN LESIONES PERSONALES O DANOS MATERIALES CONSERVE TODAS LAS INSTRUCCIONES PARA REFERENCIA FUTURA 1 1 Contenido e Tarjeta de circuito impreso PCB USB e Cubierta protectora del cono e Cable PCB e Tornillos 2 para fijar la PCB e Cable USB USB e CD del programa 1 2 Herramientas y requerimientos del sistema de PC e Destornillador Philips o llave Torx T10 y T20 dependiendo del modelo e Puerto USB para PC Windows 98 Windows 98SE Windows ME Windows 2000 o Windows XP 2 INSTALACI N DEL HARDWARE Instale el hardware antes del software del controlador USB que est en el CD del programa del paquete 2 1 Precauciones de seguridad e Desconecte la balanza de la toma de corriente el ctrica y retire cualquier bater a instalada antes de comenzar la instalaci n e los componentes internos como la c lula de carga y las tarjetas de circuito impreso PCB son delicados y necesitan manejarse con cuidado e Noexponga los componentes internos a descarga el ctrica est tica e La PCB debe
6. des ouvertures r v l es en d montant chaque pied REMARQUE Lors du d montage du pied vitez de laisser reposer la balance sur sa partie sup rieure sur le c ne du capteur Si cela s av re n cessaire placez le couvercle du c ne de protection en plastique provenant du kit sur le c ne du capteur afin de minimiser les risques de d t rioration du capteur reportez vous la figure 2A b Mod les grande armature D vissez les 2 vis et les agrafes de masse en partie sup rieure de la balance r v l es par le d montage de la plaque EMC REMARQUE Si la balance a t commercialement approuv e les autocollants d authenticit recouvrant les vis du logement devront tre d coll s De ce fait la balance devra tre nouveau approuv e et scell e Soulevez avec pr caution le capot sup rieur du logement inf rieur en prenant garde au c ble connect au circuit imprim principal D branchez le c ble du circuit imprim principal et mettez ensuite de c t le capot sup rieur D vissez les 2 vis fixant la plaque du couvercle COM2 vers l arri re et droite du logement inf rieur reportez vous la figure 2B Mettez au rebut les 2 vis et la plaque du couvercle Montez le circuit imprim de la deuxi me interface USB dans les emplacements correspondants et fixez l ensemble avec les 2 vis fournies reportez vous la figure 2C Connectez le c ble du circuit imprim sur a le circuit imprim de
7. l installation et la mise en fonctionnement VEUILLEZ LIRE TOUS LES AVERTISSEMENTS DE S CURIT AVANT D INSTALLER DE CONNECTER OU DE PROC DER L ENTRETIEN DE LA BALANCE SI CES AVERTISSEMENTS NE SONT PAS RESPECT S DES BLESSURES ET OU DES DOMMAGES MAT RIELS PEUVENT EN R SULTER CONSERVEZ TOUTES LES INSTRUCTIONS POUR R F RENCE ULT RIEURE 1 1 Contenu e Circuit imprim USB e Couvercle du c ne de protection e C ble de circuit imprim e 2 vis de fixation du circuit e Cable USB imprim USB e CD du programme 1 2 Outils et configuration syst me minimum du PC e Tournevis Philips ou tournevis Torx T10 et T20 en fonction du mod le e Port USB PC Windows 98 Windows 98SE Windows ME Windows 2000 ou Windows XP 2 INSTALLATION DU MATERIEL Installez d abord le mat riel avant le logiciel du pilote USB se trouvant sur le CD du programme du kit 2 1 Pr cautions de s curit e D connectez la balance de son alimentation secteur et retirez les piles en place avant de commencer l installation e Les composants internes comme le capteur et les circuits imprim s sont fragiles et doivent tre manipul s avec soin e N exposez pas les composants internes des d charges d lectricit statique e Les circuits imprim s doivent tre manipul s uniquement par les bords ne placez jamais les doigts sur les circuits ou sur les composants 2 2 Installation du Mat riel La s rie Adventurer Pro se pr sente s
8. la cubierta superior del gabinete inferior tomando en cuenta el cable que esta conectado con el conjunto de la PCB principal Desenchufe el cable del conjunto de la PCB principal y luego aparte la cubierta superior Retire los dos tornillos que sujetan la placa del puerto COM2 hacia la parte anterior y posterior del gabinete inferior vea la Figura 2B Deseche la placa y los dos tornillos Instale la PCB USB sobre las bases correspondientes con los dos tornillos incluidos vea la Figura 2C Conecte el cable de la PCB en a la PCB USB y b en el conector CN6 en la tarjeta para PC principal en la parte anterior de la balanza vea la Figura 2D Corra el cable PCB hacia el lado izquierdo del gabinete inferior Reensamble la balanza en orden inverso del proceso de desensamble teniendo cuidado de no prensar ning n cable dentro o entre la parte superior e inferior del gabinete ES 4 Paquete de interfaz USB Cubierta del cono para modelos de bastidor peque o Placa de cubierta del COM2 Figura 2A Figura 2B PCB USB Cable PCB Figura 2C Figura 2D 3 INSTALACI N DEL SOFTWARE Despu s de instalar el hardware instale el software del controlador USB que est en el CD del paquete 3 4 Instalaci n del software 1 Inserte el CD suministrado dentro del controlador de CD ROM de la computadora 2 Conecte la b scula Adventurer Pro al puerto USB de la computadora a trav s de un cable USB est ndar suministrado 3
9. manejarse solamente tom ndola por los bordes y nunca se deben colocar los dedos sobre los conductores o tramas 2 2 Instalaci n del Hardware La serie Adventurer Pro viene en diferentes configuraciones vea las figuras 1A B C Desensamble y ensamble la balanza de acuerdo con la configuraci n que corresponda a su modelo ES 2 Paquete de interfaz USB Cubierta de la pantalla contra corrientes de aire Pantalla contra corrientes de aire Plato de pesaje N A Soporte del plato de pesaje at Aro indicador de viento Aro adaptador Placa EMC Plato de pesaje Soporte del plato de pesaje Placa EMC Tornillos de la cubierta 2 e Tornillos de la cubierta 2 Figura 1A Fe Pd la Plato de pesaje Plato de pesaje es P Q Soporte del plato E Wo Soporte del plato Z de pesaje 1 de pesaje Aro indicador Ve y N de viento ME dre Placa EMC Placa EMC gi Tornillos dela lt Tornillos de la cubierta 2 Cubierta 2 Figura 1B Puertas de et Qu cristal Aw Plato de z pesaje 6 Tornillos dela cubierta 2 Figura 1C 1 Paquete de interfaz USB EN 3 Con la energia de la balanza interrumpida retire cualquier pantalla contra corrientes de aire o paneles de cristal de pantalla contra corrientes de aire el plato de pesaje el soporte del plato de pesaje y cualquier aro indicador de viento o aro adaptador
10. you specify To startthe search click Next If you are searching on a floppy disk or CD ROM drive insertthe floppy disk or CD before clicking Next Optional search locations Floppy disk drives Iv CD ROM drives Specify a location T Microsoft Windows Update Back Cancel CRAN 3 5 Les deux pilotes seront install s dans une s quence cons cutive Par cons quent vous r p terez les tapes de l cran 1 l cran 4 pour ex cuter l installation Found New Hardware Wi Completing the Found New Hardware Wizard USB Serial Converter Windows has finished installing the software for this device To close this wizard click Finish lt Back Cancel CRAN 4 Option pour l interface USB FR 7 6 Apr s avoir cliqu sur le deuxi me bouton Terminer le logiciel du pilote USB est install et Windows affecte un port COM virtuel l interface USB Windows affecte g n ralement les ports COM en s quence suivant les affectations pr c dentes A titre d exemple si COM3 et COMA ont d j t affect s le port COM virtuel pour la nouvelle interface USB qui est galement connu comme Port s rie USB sous Windows sera associ COM5 3 2 Recherche d information sur le port s rie USB Vous trouverez des informations relatives au port s rie USB sur le panneau de configuration en cliquant sur SYST ME Une fen tre Propri t s syst me s affiche Cliquez sur l onglet Mat riel
11. D ROM prima di fare clic su Avanti IT 6 Kit Interfaccia USB Found New Hardware Wizard Locate Driver Files DI Where do you want Windows to search for driver files NS Search for driver files forthe following hardware device Gp USB lt gt Serial The wizard searches for suitable drivers in its driver database on your computer and in any of the following optional search locations that you specify To startthe search click Next If you are searching on a floppy disk or CD ROM drive insertthe floppy disk or CD before clicking Next Optional search locations Floppy disk drives Iv CD ROM drives Specify a location T Microsoft Windows Update Back Cancel SCHERMATA 3 5 due driver vengono installati in sequenze successive Pertanto necessario ripetere le istruzioni nelle schermate da 1 a 4 per completare l installazione Found New Hardware Wi Dt Completing the Found New Hardware Wizard USB Serial Converter Windows has finished installing the software for this device To close this wizard click Finish lt Back Cancel SCHERMATA 4 Kit Interfaccia USB IT 7 6 Dopo aver fatto clic sul secondo pulsante Fine il software del driver USB risulta installato e Windows assegna una porta COM virtuale all interfaccia USB In genere Windows assegna le porte COM in sequenza Ad esempio se le porte COM3 e COM4 sono gia state assegnate in precedenza la porta COM virtu
12. Hardware wizard helps you install uninstall repair unplug 5 00 2195 b eject and configure your hardware Service Pack 4 Hardware Wizard Regards e r Ohaus Ohous EUR Manager 51873 007 3586105 09046 Mm The Device Manager lists all the hardware devices installed on Zum your computer Use the Device Manager to change the properties of any device Computer Intel R Pentium Driver Signing Device Manager R 4 CPU 2 40GHz AT AT COMPATIBLE r Hardware Profiles 523 760 KB RAM Hardware profiles provide a way for you to set up and store AS itererkhardware contiguretione Hardware Profiles oes A se Der serielle USB Port befindet sich unter Ports COM amp LPT im Fenster Device Manager Wenn der nachstehende Bildschirm erscheint zeigt der Device Manager die COM Portnummer des seriellen USB Ports als COM3 an Die COM Portnummer die in diesem Fenster erscheint ist die COM Portnummer welche die PC Anwendung zur Kommunikation mit der Waage verwendet DE 8 USB Schnittstellenoption ll File Action View Help e mj amp glm E Y Computer Hs Disk drives H 9 Display adapters Fl DVD CD ROM drives Floppy disk controllers Id Floppy disk drives H 6 Human Interface Devices H E IDE ATA ATAPI controllers H Keyboards El Mice and other pointing devices El 3 Monitors 9 Network adapters EH Ports COM amp LPT I Communications Port COM1 I Communications Port COM2 Y EC
13. Hardware wizard helps you install uninstall repair unplug EN eject and configure your hardware Hardware Wizard Device Manager m The Device Manager lists all the hardware devices installed on am your computer Use the Device Manager to change the properties of any device Driver Signing Device Manager Hardware Profiles J Hardware profiles provide a way for you to setup and store different hardwere configurations Hardware Profiles The USB Serial Port can be found under Ports COM amp LPT in the Device Manger window In the case of the picture shown below the Device Manger window shows the COM port number of the USB Serial Portas COM3 The COM port number shown in this window is the COM port number the PC application will use to communicate with balance EN 8 USB Interface Kit PO cx File Action View Help gt 081219 E Y Computer Hs Disk drives H 9 Display adapters E DVD CD ROM drives Floppy disk controllers J Floppy disk drives H B Human Interface Devices H E IDE ATAJATAPI controllers H Keyboards E 1 Mice and other pointing devices B g Monitors E E Network adapters EP Ports COM amp LPT I Communications Port COM1 I Communications Port COM2 Y ECP Printer Port LPT1 FUSE Serial Port COM3 EM Processors E Sound video and game controllers System devices RI Universa
14. Help e mj amp glm E Y Computer Hs Disk drives H 9 Display adapters Fl DVD CD ROM drives Floppy disk controllers Id Floppy disk drives H 6 Human Interface Devices H E IDE ATA ATAPI controllers H Keyboards El Mice and other pointing devices El 3 Monitors 9 Network adapters Ei Ports COM amp LPT I Communications Port COM1 I Communications Port COM2 Y ECP Printer Port LPT1 4 USB Serial Port COM3 EM Processors E Sound video and game controllers System devices El Universal Serial Bus controllers zl Remarque lorsque vous utilisez l interface USB avec des programmes limitant le nombre de d signations de port COM tel que par exemple Ohaus MassTracker qui ne permet que COM 2 3 et 4 vous devez affecter un de ces num ros de port au nouveau port virtuel Pour changer le num ro du port affect au port s rie USB double cliquez sur Port s rie USB dans la fen tre Gestionnaire de p riph riques Une fen tre intitul e Propri t s du port s rie USB COMx s affiche Cliquez sur l onglet Param tres du port puis sur le bouton Avanc pour afficher Param tres avanc s pour COMXx et changez le num ro du port COM 4 CONFIGURATION DU MENU DE LA BALANCE Le logiciel Adventurer Pro d finit le port s rie USB comme le port RS232 2 Reportez vous au manuel d instructions fourni avec la balance Adventurer Pro Configurez le port de communication RS232 ainsi que les param tre
15. OHAUS USB Interface Kit P N 71208792 Instruction Manual Paquete de interfaz USB N P 71208792 Manual de instrucciones Option pour l interface USB Ref 71208792 Manuel d instructions USB Schnittstellenoption Teilenr 71208792 Bedienungsanleitung Kit Interfaccia USB N P 71208792 Manuale di istruzioni USB Interface Kit EN 1 1 INTRODUCTION This USB Interface Kit P N 71208792 provides a solution to connect an Adventurer Pro balance to a computer via a Universal Serial Bus USB port This interface kit uses a USB serial conversion class that allows the use of a USB port like an RS232 serial port also known as a Virtual COM port Please read this manual completely before installation and operation READ ALL SAFETY WARNINGS BEFORE INSTALLING MAKING CONNECTIONS OR SERVICING THE BALANCE FAILURE TO COMPLY WITH THESE WARNINGS COULD RESULT IN PERSONAL INJURY AND OR PROPERTY DAMAGE RETAIN ALL INSTRUCTIONS FOR FUTURE REFERENCE 1 1 Contents e USB Printed Circuit Board PCB e Protective Cone Cover e PCB Cable e Screws 2 to secure the USB PCB e USB Cable e Program CD 1 2 Tools and PC System Requirements e Philips screwdriver or Torx driver T10 8 T20 depending on model e PCUSB port e Windows 98 Windows 98SE Windows ME Windows 2000 or Windows XP 2 INSTALLATION OF HARDWARE Install the hardware first before the USB driver software contained in the kit program CD 2 1 Safety Precautions e Disconnect
16. P Printer Port LPT1 4 USB Serial Port COM3 EM Processors E Sound video and game controllers System devices El Universal Serial Bus controllers zl Hinweis Wenn die USB Schnittstelle mit Programmen verwendet wird welche die Anzahl der COM Port Bezeichnungen begrenzen beispielsweise gestattet Ohaus MassTracker nur COM1 2 3 amp 4 ist es eventuell erforderlich eine dieser Portnummern dem neuen virtuellen Port zuzuweisen Zum ndern der Portnummer die dem seriellen USB Port zugewiesen wurde doppelklicken Sie auf USB Serial Port im Fenster Device Manager Das Fenster USB Serial Port COMx Properties Serielle USB Port Eigenschaften COMx wird eingeblendet Klicken Sie auf das Register Port Settings Port Einstellungen und klicken Sie auf die Schaltfl che Advanced Erweitert um Advanced Settings for COMx Erweiterte Einstellungen f r COMx aufzurufen und die COM Portnummer zu ndern 4 WAAGENMENUEINRICHTUNG Die Adventurer Pro Software den seriellen USB Port als RS232 2 Port Beziehen Sie sich auf die mit der Adventurer Pro Waage gelieferte Bedienungsanleitung Richten Sie die RS232 Kommunikations und Druckparameter gem der Beschreibung in den RS232 2 und Druck 2 Untermen s ein diese sind nach Installation des Satzes aktiviert 5 WARTUNG Wartungsinformationen Wenn Sie in den Vereinigten Staaten Hilfe ben tigen rufen Sie bitte die folgende in den USA geb hrenfreie Numme
17. ale per la nuova interfaccia USB denominata anche Porta USB in Windows sara associata a COM5 3 2 Informazioni sulla porta USB Per informazioni sulla porta USB selezionare il pannello di controllo e fare clic su SISTEMA Viene visualizzata la finestra Proprieta del sistema Selezionare la scheda Hardware e fare clic sul pulsante Gestione periferiche per visualizzare la finestra Gestione periferiche System Properties xl System Properties 2h x General Network Identification Hardware User Profiles Advanced General Network Identification Hardware User Profiles Advanced System r Hardware Wizard Microsoft Windows 2000 The Hardware wizard helps you install uninstall repair unplug 5 00 2195 sw eject and configure your hardware Service Pack 4 Hardware Wizard Registered to T Ohaus re Device Manager 51873 007 3586105 09046 fm The Device Manager lists all the hardware devices installed on a your computer Use the Device Managerto change the properties of any device Computer Intel R Pentium Driver Signing Device Manager R 4 CPU 2 40GHz AT AT COMPATIBLE Hardware Profiles 523 760 KB RAM gt Hardware profiles provide a way for you to setup and store A9 dierenthardware configurations Hardware Profiles NEM Ge oe La porta USB riportata in Porte COM e LPT nella finestra Gestione periferiche Nel caso della figura riportata in basso nella f
18. chritte in Bildschirm 1 bis 4 wiederholen um die Installation abzuschlieRen Found New Hardware Wizard Completing the Found New Hardware Wizard USB Serial Converter Windows has finished installing the software for this device To close this wizard click Finish lt Back Cancel BILDSCHIRM 4 USB Schnittstellenoption DE 7 6 Nachdem Sie auf die zweite Schaltfl che Finish Fertig stellen geklickt haben ist die USB Treibersoftware fertig installiert und Windows weist der USB Schnittstelle einen virtuellen COM Port zu In der Regel weist Windows COM Ports in numerischer Reihenfolge zu Wenn z B COM3 und COM4 bereits zuvor zugewiesen wurden wird der virtuelle COM Port f r die neue USB Schnittstelle die auch als USB Serial Port Serieller USB Port in Windows bezeichnet wird mit COM5 verkn pft 3 2 Serielle USB Port informationen finden Informationen zum seriellen USB Port k nnen aufgerufen werden indem Sie in die Systemsteuerung gehen und auf SYSTEM klicken Das Fenster System Properties Systemeigenschaften wird eingeblendet Klicken Sie auf das Register Hardware und auf die Schaltfl che Device Manager Ger te Manager um das Fenster Device Manager aufzurufen General Network Identification Hardware User Profiles Advanced General Network Identification Hardware User Profiles Advanced System r Hardware Wizard Microsoft Windows 2000 The
19. e recommended C Display a list of the known drivers for this device so that can choose a specific driver PANTALLA 2 coax cae ES 6 Paquete de interfaz USB Found New Hardware Wizard Locate Driver Files ey Where do you want Windows to search for driver files NS Search for driver files forthe following hardware device Gp USB lt gt Serial The wizard searches for suitable drivers in its driver database on your computer and in any of the following optional search locations that you specify To startthe search click Next If you are searching on a floppy disk or CD ROM drive insertthe floppy disk or CD before clicking Next Optional search locations Floppy disk drives Iv CD ROM drives Specify a location T Microsoft Windows Update Back Cancel PANTALLA 3 5 Dos controladores ser n instalados en secuencia back to back Por lo tanto usted repetir los pasos de la pantalla 1 a la pantalla 4 para completar la instalaci n Found New Hardware Wi Completing the Found New Hardware Wizard USB Serial Converter Windows has finished installing the software for this device To close this wizard click Finish lt Back Cancel PANTALLA 4 Paquete de interfaz USB EN 7 6 Despu s de hacer clic en el bot n Finalizar el software del controlador USB es instalado y Windows asigna un puerto COM Virtual a la interfase USB Windows tipicamente asig
20. een 4 to complete installation Found New Hardware Wizal Completing the Found New Hardware Wizard USB Serial Converter Windows has finished installing the software forthis device To close this wizard click Finish Back Cancel SCREEN 4 USB Interface Kit 6 After clicking the second Finish button the USB driver software is installed and EN 7 Windows assigns a Virtual COM Port to the USB interface Windows typically assigns COM Ports in number sequence after previous assignments For example if COM3 and COM4 have been previously assigned the Virtual COM Port for the new USB interface which is also named USB Serial Port in Windows will be associated with COM5 3 2 Finding USB Serial Port Information Information on the USB Serial Port can be found by going to the control panel and clicking on SYSTEM A System Properties window will come up Click the Hardware tab and click the Device Manager button to bring up the Device Manager window System Properties General Network Identification Hardware User Profiles Advanced x Registered to r Ohaus Ohaus 51873 007 3586105 09046 System Microsoft Windows 2000 5 00 2195 Service Pack 4 Computer Intel P Pentium R 4 CPU 2 40GHz AT AT COMPATIBLE 523 760 KB RAM cost o 21xi 2x General Network Identification Hardware User Profiles Advanced Hardware Wizard The
21. ella porta COM 4 CONFIGURAZIONE DEI MENU DELLA BILANCIA Il software Adventurer Pro definisce la porta USB come porta RS232 2 Fare riferimento al manuale di istruzioni fornito con la bilancia Adventurer Pro Impostare i parametri di comunicazione e stampa della RS232 come illustrato nei menu secondari RS232 2 e Print 2 abilitati quando si installa il kit 5 MANUTENZIONE Informazioni relative all assistenza Per assistenza tecnica negli Stati Uniti contattare il numero verde USA 1 800 526 0659 dalle ore 8 e alle ore 17 ora della costa orientale degli Stati Uniti II personale specializzato Ohaus addetto alla manutenzione dei prodotti sar disponibile per l assistenza Al di fuori degli Stati Uniti consultare il sito Web www ohaus com per individuare l ufficio Ohaus pi vicino S OHAUS Ohaus Corporation 19A Chapin Road P O Box 2033 Pine Brook NJ 07058 2033 USA Tel 973 377 9000 Fax 973 944 7177 With offices worldwide Con oficinas alrededor del mundo Avec des bureaux dans le monde entier Weltweite Gesh ftsstellen Con uffici in tutto il mondo www ohaus com 1 2 1 0 3 9 9 8 P N 80100401 A Ohaus Corporation 2010 all rights reserved todos los derechos reservados tous droits r serv s Alle Rechte vorbehalten tutti i diritti riservati Printed in China Impreso en la China Imprim en Chine Gedruckt in China Stampato in Cina
22. facing inwards note their positions in case dislodged and needing to be re installed Disassemble the top from the bottom housing depending on model a Small frame models Remove the 4 feet then remove the 4 screws inside the openings uncovered by the removal of each foot NOTE While removing the feet avoid resting the balance on its top side over the load cell cone assembly If needing to do so place the protective plastic cone cover from the kit over the load cell cone assembly to minimize risk of damage to the load cell See Figure 2A b Large frame models Remove the 2 screws and any grounding clip on the top of the balance that were exposed by the removal of the EMC plate NOTE Ifthe balance was trade approved any sealing sticker covering the housing screws will need to be removed In effect the balance will have to be re approved and re sealed Carefully lift the top cover from the bottom housing mindful of the cable connected to the main PCB assembly Unplug the cable from the main PCB assembly then set aside the top cover Remove the 2 screws securing the COM2 cover plate towards the back and right of the bottom housing See Figure 2B Discard the cover plate and 2 screws Mount the USB PCB over the corresponding stands then secure with the 2 screws provided See Figure 2C Connect the PCB cable to a the USB PCB and b to connector CN6 on the main PC board on the front of the balance see Figure 2D
23. i dessous Option pour l interface USB FR 5 Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install a device driver for a hardware device To continue click Next lt Back Cancel CRAN 1 4 Cliquez sur le bouton Suivant L cran 2 s affiche Cliquez sur Suivant pour passer l cran 3 et cochez Lecteur CD ROM avant de cliquer sur Suivant Found New Hardware Wizard Install Hardware Device Drivers ey Adevice driveris a software program that enables a hardware device to work with an NS operating system This wizard will complete the installation forthis device a USB lt gt Serial A device driver is a software program that makes a hardware device work Windows needs driver files for your new device To locate driver files and complete the installation click Next What do you want the wizard to do Search for a suitable driver for my device recommended C Display alist of the known drivers for this device so that can choose a specific driver Book cara CRAN 2 FR 6 Option pour l interface USB Found New Hardware Wizard Locate Driver Files ey Where do you want Windows to search for driver files NS Search for driver files forthe following hardware device Gp USB lt gt Serial The wizard searches for suitable drivers in its driver database on your computer and in any of the following optional search locations that
24. inestra Gestione periferiche il numero della porta COM per la porta USB COM3 Il numero di porta COM mostrato in questa finestra quello che l applicazione del PC utilizzer per comunicare con la bilancia IT 8 Kit Interfaccia USB IB xi File Action View Help e mj amp glm E Y Computer Hs Disk drives H 9 Display adapters Fl DVD CD ROM drives Floppy disk controllers Id Floppy disk drives H 6 Human Interface Devices H E IDE ATA ATAPI controllers H Keyboards El Mice and other pointing devices El 3 Monitors 9 Network adapters Ei Ports COM amp LPT I Communications Port COM1 I Communications Port COM2 Y ECP Printer Port LPT1 4 USB Serial Port COM3 EM Processors E Sound video and game controllers System devices FA Universal Serial Bus controllers zl Nota quando si utilizza l interfaccia USB con programmi che limitano il numero per le designazioni delle porte COM ad esempio Ohaus MassTracker consente solo COM1 2 3 e 4 pu essere necessario assegnare uno di questi numeri alla nuova porta virtuale Per modificare il numero assegnato alla porta USB fare clic su Porta USB nella finestra Gestione periferiche Viene visualizzata la finestra Propriet Porta di comunicazione COMx Selezionare la scheda Impostazioni della porta e fare clic sul pulsante Avanzate per visualizzare la finestra Impostazioni avanzate COMx e modificare il numero d
25. k bevor Sie auf Next klicken Found New Hardware Wizard i Install Hardware Device Drivers SS A device driver is a software program that enables a hardware device to work with an NS operating system This wizard will complete the installation forthis device e USB Serial A device driver is a software program that makes a hardware device work Windows needs driver files for your new device To locate driver files and complete the installation click Next What do you wantthe wizard to do Search for a suitable driver for my device recommended C Display a list of the known drivers for this device so that can choose a specific driver eck cae BILDSCHIRM 2 DE 6 USB Schnittstellenoption Found New Hardware Wizard E Locate Driver Files ey Where do you want Windows to search for driver files NS Search for driver files for the following hardware device DI USB lt gt Serial The wizard searches for suitable drivers in its driver database on your computer and in any of the following optional search locations that you specify To startthe search click Next Ifyou are searching on a floppy disk or CD ROM drive insert the floppy disk or CD before clicking Next Optional search locations Floppy disk drives Iv CD ROM drives Specify a location T Microsoft Windows Update Back Cancel BILDSCHIRM 3 5 Die zwei Treiber werden hintereinander installiert Daher m ssen Sie die S
26. l Serial Bus controllers Y Note When using the USB interface with programs that limit the number of COM port designations e g Ohaus MassTracker allows only COM1 2 3 amp 4 it may be necessary to assign one of these port numbers to the new virtual port To change the port number assigned to USB Serial Port double click USB Serial Port in the Device Manager window A USB Serial Port COMx Properties window will come up Click the Port Settings tab and click on the Advanced button to bring up Advanced Settings for COMx and change COM port number 4 BALANCE MENU SETUP The Adventurer Pro software defines the USB Serial port as the RS232 2 port Refer to the instruction manual supplied with the Adventurer Pro balance Set up the RS232 communication and printing parameters as described in the RS232 2 and Print 2 submenus enabled when this kit is installed 5 MAINTENANCE Service Information For service assistance in the United States call toll free 1 800 526 0659 between 8 00 AM and 5 00 PM Eastern Standard Time An Ohaus Product Service Specialist will be available to assist you Outside the USA please visit our website at www ohaus com to locate the Ohaus office nearest you Paquete de interfaz USB EN 1 1 INTRODUCCI N Este paquete de interfaz USB N P 71208792 ofrece una soluci n para conectar una balanza Adventurer Pro con una computadora a trav s de un puerto USB Universal
27. la deuxi me interface USB et b au connecteur CN6 du circuit imprim principal sur la partie avant de la balance reportez vous la figure 2D Faites cheminer le c ble du circuit imprim vers le c t gauche du logement inf rieur Remontez la balance dans l ordre inverse du d montage en veillant ne pas coincer un c ble entre les logements sup rieurs et inf rieurs FR 4 Option pour l interface USB Couvercle du c ne de protection en plastique mod les petite armature Plaque du couvercle COM2 Figure 2A Figure 2B Circuit imprim de la interface USB C ble du circuit imprim Figure 2C Figure 2D 3 INSTALLATION DU LOGICIEL Apr s avoir install le mat riel installez le logiciel du pilote USB se trouvant sur le CD du kit 3 1 Installation du logiciel 1 Ins rez le disque fourni dans le lecteur de CD ROM de l ordinateur 2 Connectez la balance Adventurer Pro au port USB de l ordinateur l aide d un c ble USB standard fourni 3 La fen tre de l Assistant de d tection de nouveau mat riel s affiche Les captures d cran suivantes illustrent des exemples d installation avec Windows 20006 D autres syst mes d exploitation Microsoft Windows peuvent afficher une fen tre semblable avec quelques diff rences L Assistant de mat riel dans toutes les versions de Windows vous guidera au cours de l installation des deux pilotes n cessaires qui se trouvent sur CD Les tapes sont d crites c
28. los tama os y formas varian para exponer completamente la placa EMC en la parte superior de la balanza Retire los dos tornillos y la placa EMC NOTA algunos modelos con aro rectangular indicador de viento incluyen 4 pasadores para alinear la placa EMC Tenga cuidado de no perder esos pasadores Estos estan marcados F anteriores o B posteriores con las marcas hacia el lado interno observe su colocaci n en caso que salgan de su lugar y necesite volver a colocarlos Desensamble la parte superior del gabinete inferior dependiendo del modelo a Modelos de bastidor peque o retire las cuatro patas y luego los cuatro tornillos que estan dentro de las aberturas que quedan expuestas al quitar cada pata NOTA al retirar las patas evite apoyar la balanza sobre su parte superior sobre el conjunto del cono de la c lula de carga Si es necesario hacerlo coloque la cubierta protectora de plastico del cono del paquete sobre el conjunto del cono de la c lula de carga para minimizar el riesgo de da ar la c lula de carga vea la Figura 2A b Modelos de bastidor grande retire los dos tornillos y la pinza de conexi n a tierra de la parte superior de la balanza que quedaron expuestos al retirar la placa EMC NOTA Si la balanza esta aprobada para comercio es necesario retirar la etiqueta adhesiva que cubre los tornillos del gabinete De hecho la balanza deber ser aprobada y sellada nuevamente Levante con cuidado
29. n 2 zum Sichern der USB Platine e USB Kabel e Programm CD 1 2 Werkzeuge und PC Systemvoraussetzungen Kreuszschlitzschraubendreher oder Torx Schraubendreher T10 u T20 je nach Modell e PC USB Port Windows 98 Windows 98SE Windows ME Windows 2000 oder Windows XP 2 INSTALLATION DER HARDWARE Zuerst die Hardware einbauen bevor Sie die USB Treibersoftware auf der Programm CD des Satzes installieren 2 4 Sicherheitsvorkehrungen e Die Waage von der Netzstromzufuhr abtrennen und alle eingelegten Batterien herausnehmen bevor Sie mit der Installation beginnen e Interne Komponenten wie beispielsweise die W gezelle und Platinen PCB sind empfindlich und m ssen vorsichtig behandelt werden e Die internen Komponenten keiner statischen Entladung aussetzen e Die Platinen sollten nur an den Kanten angefasst werden Auf keinen Fall irgendwelche Dr hte oder Leiterbahnen mit den Fingern ber hren 2 2 Installation der hardware Die Adventurer Pro Serie ist in unterschiedlichen Konfigurationen erh ltlich siehe Abbildungen 1A B C Die Waage gem der Konfiguration die f r Ihr Modell passend ist auseinander und zusammenbauen DE 2 USB Schnittstellenoption Zugluftschutzabdeckung Zugluftschutz Schale Schalentrager f Schale Windring Adapterring Schalentr ger EMV Platt um EMV Platte Abdeckungsschrauben T Abdeckungsschrauben 2 2 A j Schale 2 PRESA 3 S
30. na los puertos COM en una secuencia num rica despu s de las asignaciones previas Por ejemplo si ya se han asignado previamente los COM 3 y COM4 el puerto COM Virtual para la nueva interfase USB la cual tambi n es llamada Puerto de serie universal en Windows estara asociado con COMS 3 2 Hallando la Informaci n del Puerto Serial USB La informaci n sobre el puerto serial USB puede encontrarse yendo al panel de control y haciendo clic en SISTEMA Aparecer una ventana de Propiedades del sistema Haga clic en la pestafia Hardware y luego en el bot n Administrador de dispositivos para visualizar la pantalla de Administrador de dispositivos General Network Identification Hardware User Profiles Advanced General Network Identification Hardware User Profiles Advanced System Hardware Wizard Microsoft Windows 2000 E The Hardware wizerd helps you install uninstall repair unplug 5 00 2195 sy eject and configure your hardware Service Pack 4 Hard Wizard gr Feen r Ohaus vn Device Manager 51873 007 3586105 09046 mm The Device Manager lists all the hardware devices installed on your computer Use the Device Manager to change the properties of any device Computer Intel R Pentium Driver Signing Device Manager R 4 CPU 2 40GHz AT AT COMPATIBLE Hardware Profiles 523 760 KB RAM Hardware profiles provide a way for you to setup and store BP ditferen
31. nsioni e forme variabili per esporre completamente la piastra EMC sulla parte superiore della bilancia 2 Rimuovere le 2 viti e la piastra EMC NOTA alcuni modelli con anello rettangolare per correnti d aria sono dotati di 4 pin per allineare la piastra EMC Fare attenzione a non perderli Sono contrassegnati con F davanti o B retro con i segni rivolti verso l interno notare le posizioni nel caso in cui si spostino e vadano reinstallati 3 Smontare l alloggiamento superiore da quello inferiore in base al modello a Modelli con telaio piccolo rimuovere i quattro piedini e quindi le quattro viti all interno delle aperture lasciate scoperte a seguito della rimozione di ciascun piedino NOTA durante la rimozione dei piedini evitare di poggiare la bilancia sul lato superiore sul gruppo conico della cella di carico In caso contrario sistemare il coperchio conico protettivo in plastica del kit sopra l assemblaggio della cella di carico per ridurre al minimo il rischio di danni alla cella di carico vedere Figura 2A b Modelli con telaio grande rimuovere le due viti e i morsetti di terra dalla parte superiore della bilancia che sono stati esposti a seguito della rimozione della piastra EMC NOTA se la bilancia approvata per il commercio necessario rimuovere ciascun adesivo che copre le viti dell alloggiamento In effetti la bilancia deve essere nuovamente approvata e sigillata 4 Sollevare con attenzi
32. one il coperchio superiore dall alloggiamento inferiore prestando attenzione al cavo connesso al gruppo del PCB principale 5 Scollegare il cavo dal gruppo del PCB principale quindi riporre il coperchio superiore 6 Rimuovere le due viti che fissano la piastra di copertura COM2 verso la parte posteriore e a destra dell alloggiamento inferiore vedere Figura 2B Rimuovere la piastra di copertura e le due viti e gettarle 7 Montare il PCB USB sui supporti corrispondenti fissandolo con le due viti in dotazione vedere Figura 2C 8 Collegare il cavo PCB al a PCB USB e b connettore CN6 sulla scheda madre del PC sul davanti della bilancia vedere Figura 2D Instradare il cavo PCB verso il lato sinistro dell alloggiamento inferiore 9 Riassemblare la bilancia adottando la procedura inversa prestando attenzione a non pizzicare i cavi all interno o accanto agli alloggiamenti superiore e inferiore IT 4 Kit Interfaccia USB Coperchio conico per modelli con telaio piccolo Piastra di copertura COM2 Figura 2A Figura 2B PCB USB Cavo PCB Figura 2C Figura 2D 3 INSTALLAZIONE DEL SOFTWARE Dopo aver installato l hardware installare il driver USB contenuto nel CD del kit 3 1 Installazione del Software 1 Inserire il CD fornito nell apposita unit del computer 2 Collegare la bilancia Adventurer Pro alla porta USB del computer tramite un cavo USB standard fornito 3 Viene visualizzata la finestra Installazi
33. one nuovo hardware Di seguito sono fornite alcune figure con esempi di installazione con Windows 2000 Per gli altri sistemi operativi Microsoft Windows viene visualizzata una finestra leggermente diversa L installazione guidata nuovo hardware per tutte le versioni di Windows fornisce le istruzioni necessarie per installare i due driver presenti sul CD Di seguito illustrata la stessa procedura Kit Interfaccia USB 4 Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install a device driver for a hardware device To continue click Next SCHERMATA 1 Found New Hardware Wizard Install Hardware Device Drivers I device driver is a software program that enables a hardware device to work with an RI operating system This wizard will complete the installation for this device e USB lt gt Serial A device driver is a software program that makes a hardware device work Windows needs driver files for your new device To locate driver files and complete the installation click Next What do you wantthe wizard to do Search for a suitable driver for my device recommended C Display a list of the known drivers for this device so that can choose a specific driver eck cana SCHERMATA 2 IT 5 Fare clic sul pulsante Avanti viene visualizzata la seconda schermata Fare clic su Avanti per passare alla schermata 3 e selezionare Unita C
34. ontenuto nel CD del kit 2 1 Misure di sicurezza e Prima di effettuare l installazione scollegare la bilancia dall alimentazione elettrica e rimuovere le batterie eventualmente installate e componenti interni quali la cella di carico e le schede a circuiti stampati PCB sono delicati e vanno maneggiati con cura e Nonesporrei componenti interni alle scariche elettrostatiche e PCB devono essere maneggiati afferrando solo le estremit e i percorsi o le tracce non vanno mai toccati con le dita 2 2 Installazione del hardware prodotti della serie Adventurer Pro sono caratterizzati da configurazioni diverse vedere Figure 1A B C Smontare montare la bilancia seguendo la configurazione corrispondente al modello che si possiede IT 2 Kit Interfaccia USB Coperchio dello scudo per le correnti d aria Scudo per correnti d aria Piatto Supporto del piatto Anello per correnti d aria Anello ser Piastra EMC Piatto Supporto del piatto Piastra EMC Viti di copertura 2 9 Viti di copertura 2 Piatto Piatto KE 53 Supporto del piatto Se Supporto del piatto So Anello per correnti d aria Figura 1B _ Sportelli in vetro Figura 1C Kit Interfaccia USB IT 3 1 Dopo aver scollegato la bilancia dall alimentazione rimuovere gli scudi per correnti d aria o i pannelli in vetro il piatto e il suo supporto e l anello per correnti d aria o l anello adattatore dime
35. ous diff rentes configurations reportez vous aux figures 1A B C D montez remontez la balance conform ment la configuration qui correspond votre mod le FR 2 Option pour l interface USB i Couvercle du pare vent Pare vent Plateau Plateau Support plateau Virole renforc e Anneau d adaptation Plaque EMC Support plateau Plaque EMC 2 vis du couvercle 7 2 vis du couvercle Virole renforc e N SR Figure 1B _ Portes en verre aa Plateau__ Figure 1C 1 Option pour l interface USB FR 3 La balance tant d connect e du secteur retirez les pare vent ou les pare vent en verre le plateau le support du plateau la virole renforc e ou l anneau d adaptation les dimensions et les formes varient afin d exposer compl tement la plaque EMC en partie sup rieure de la balance D vissez les 2 vis et la plaque EMC REMARQUE Certains mod les avec une virole renforc e rectangulaire comprennent 4 broches d alignement de la plaque EMC Veillez ne pas perdre ces broches Elles portent la marque F avant ou B arri re avec les inscriptions orient es vers l int rieur veuillez noter leurs positions si elles sont d log es et si elles doivent tre r install es D montez la partie sup rieure sur le logement inf rieur en fonction du mod le a Mod les petite armature D montez les 4 pieds et ensuite les 4 vis l int rieur
36. ption Kegelabdeckung f r Modelle mit kleinem Rahmen COM2 Abdeckplatte Abbildung 2A Abbildung 2B Platine USB Platinenkabel Abbildung 2C Abbildung 2D 3 INSTALLATION DER SOFTWARE Nach Einbauen der Hardware die USB Treibersoftware auf der CD des Satzes installieren 3 1 Software Installation 1 Die mitgelieferte CD in das CD ROM Laufwerk des Computers einlegen 2 Die Adventurer Pro Waage mit einem Standard USB Kabel im Lieferumfang enthalten an den USP Port des Computers anschlie en 3 Das Fenster Found New Hardware Wizard Assistent f r das Suchen neuer Hardware wird eingeblendet Die folgenden Bildschirmdarstellungen sind Beispiele der Installation unter Windows 2000 Andere Microsoft Windows Betriebssysteme zeigen ein hnliches Fenster an das eventuell geringf gige Unterschiede aufweist In allen Versionen von Windows f hrt Sie der Hardware Assistent durch die Installation der erforderlichen zwei Treiber die sich auf der CD befinden Dazu werden die nachstehenden Schritte ausgef hrt USB Schnittstellenoption DE 5 Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install a device driver for a hardware device To continue click Next lt Back Cancel BILDSCHIRM 1 4 Klicken Sie auf Next Weiter und Bildschirm 2 wird eingeblendet Klicken Sie auf Next um zu Bildschirm 3 zu gelangen und markieren Sie CD ROM Drive CD ROM Laufwer
37. puis sur le bouton Gestionnaire de p riph riques pour afficher la fen tre Gestionnaire de p riph riques General Network Identification Hardware User Profiles Advanced General Network Identification Hardware User Profiles Advanced System Hardware Wizard Microsoft Windows 2000 The Hardware wizard helps you install uninstall repair unplug 5 00 2195 ST eject and configure your hardware Service Pack 4 4 Hardware Wizard Registered to o Herweewued r Ohaus pre Device Manager ORA jm The Device Manager lists all the hardware devices installed on your computer Use the Device Managerto change the properties of any device Computer Intel R Pentium Driver Signing Device Manager P 4 CPU 2 40GHz AT AT COMPATIBLE m Hardware Profiles 523 760 KB RAM Hardware profiles provide a way for you to setup and store amp ditferenthardwere configurations Hardware Profiles Omen A Consi ion Vous pouvez trouver le port s rie USB sous Ports COM et LPT dans la fen tre Gestionnaire de p riph riques Dans le cas de la capture d cran illustr e ci dessous la fen tre Gestionnaire de p riph riques affiche le num ro du port COM du port s rie USB comme COM3 Le num ro du port COM illustr dans cette fen tre est celui du port COM que l application utilisera pour communiquer avec la balance FR 8 Option pour l interface USB ll File Action View
38. r an 1 800 526 0659 zwischen 8 00 und 17 Uhr amerikanischer Ostk stenzeit Ein Produktservice Spezialist von Ohaus wird Ihnen dann weiterhelfen Au erhalb der USA besuchen Sie unsere Website unter www ohaus com um die f r Sie am n chsten gelegene Ohaus Gesch ftsstelle zu finden Kit Interfaccia USB IT 1 1 INTRODUZIONE Questo kit interfaccia USB con N P 71208792 offre una soluzione che consente di collegare una bilancia Adventurer Pro a un computer tramite porta USB Questo kit sfrutta una classe di conversione USB seriale che consente di utilizzare una porta USB come una porta seriale RS232 nota anche come porta COM virtuale Leggere integralmente il manuale prima dell installazione e della messa in funzione LEGGERE TUTTE LE AVVERTENZE DI SICUREZZA PRIMA DI PROCEDERE ALL INSTALLAZIONE ALLA REALIZZAZIONE DEI COLLEGAMENTI ALLA MANUTENZIONE DELLA BILANCIA IL MANCATO RISPETTO DI QUESTA AVVERTENZA PUO COMPORTARE DANNI ALLA PROPRIET E O LESIONI PERSONALI CONSERVARE TUTTE LE ISTRUZIONI PER RIFERIMENTI FUTURI 1 4 Indice e Scheda a circuiti stampati PCB USB e Copertura conica di protezione e Cavo PCB e Viti 2 per fissare il PCB USB e Cavo USB e CD del kit 1 2 Attrezzi e requisiti di sistema e Cacciavite Philips o Torx T10 e T20 a seconda del modello e Porta USB del PC Windows 98 Windows 98SE Windows ME Windows 2000 o Windows XP 2 INSTALLAZIONE DEL HARDWARE Installare prima l hardware del driver USB c
39. rial USB haga doble clic en USB Serial Port en la ventana de Administrador de dispositivos Aparecer una ventana de USB Serial Port COMx Properties Haga clic en la pesta a Port Settings y luego en el bot n Advanced para que aparezca Advanced Settings for COMx y cambie el n mero del puerto COM 3 CONFIGURACI N DEL MENU DE LA BALANZA El software de la Adventurer Pro define al puerto serial USB como el puerto RS232 2 Consulte el manual de instrucciones incluido con la balanza Adventurer Pro Configure los par metros de comunicaci n e impresi n del RS232 como se describe en los submen s RS232 2 y Print 2 habilitados al instalar el paquete 4 MANTENIMIENTO Informaci n de servicio Para asistencia de servicio en los Estados Unidos llame gratis al 1 800 526 0659 entre las 8 00 a m y las 5 00 p m hora del este Un especialista en servicio de productos de Ohaus estar disponible para ayudarle Fuera de los Estados Unidos visite nuestra p gina web en www ohaus com para encontrar la oficina de Ohaus m s cercana a usted Option pour l interface USB FR 1 1 INTRODUCTION Ce kit d interface USB r f renc 71208792 fournit une solution de connexion d une balance Adventurer Pro un ordinateur au moyen d un port USB Ce kit d interface utilise une classe de conversion s rie USB qui permet d utiliser un port USB s rie RS232 aussi connu sous le nom de port COM virtuel Veuillez lire entierement ce manuel avant
40. s d impression conform ment la description des sous menus RS232 et Print 2 activ s lorsque ce kit est install 5 MAINTENANCE Informations d entretien Pour toute assistance aux tats Unis composez le num ro gratuit 1 800 526 0659 de 8h00 17h00 heure de l Est Un expert des produits Ohaus se tient votre disposition pour r pondre vos questions En dehors des tats Unis visitez le site Web l adresse suivante www ohaus com pour localiser le bureau Ohaus le plus proche de chez vous USB Schnittstellenoption DE 1 1 EINLEITUNG Dieser USB Schnittstellensatz Teile Nr P N 71208792 bietet eine L sung f r das Anschlie en einer Adventurer Pro Waage an einen Computer ber einen USB Port Dieser Schnittstellensatz verwendet eine serielle USB Konversionsklasse mit der die Verwendung eines USB Ports in hnlicher Weise wie ein serieller RS232 Port auch als virtueller COM Port bekannt m glich ist Bitte lesen Sie dieses Handbuch vor der Installation und Inbetriebnahme vollst ndig durch VOR DER INSTALLATION DEM HERSTELLEN VON ANSCHL SSEN ODER DER DURCHF HRUNG VON WARTUNGSARBEITEN AN DER WAAGE M SSEN SIE ALLE SICHERHEITSHINWEISE LESEN DIE NICHTBEFOLGUNG DIESER WARNHINWEISE K NNTE ZU VERLETZUNGEN UND ODER SACHSCH DEN F HREN BEWAHREN SIE ALLE ANWEISUNGEN F R ZUK NFTIGE NACHSCHLAGEZWECKE AUF 1 1 Inhaltsverzeichnis e USB Platine PCB e Schutzabdeckung f r Kegel e Platinenkabel e Schraube
41. st lpen um eine Besch digung der Wagezelle nach M glichkeit zu vermeiden siehe Abbildung 2A b Modelle mit gro em Rahmen Die 2 Schrauben und alle Erdungslaschen oben auf der Waage entfernen die durch das Ausbauen der EMV Platte freigelegt wurden HINWEIS Wenn die Waage f r eichpflichtige Anwendungen zugelassen war m ssen alle Aufklebersiegel die die Geh useschrauben abdecken entfernt werden Danach muss die Waage neu zugelassen und neu versiegelt werden Die obere Abdeckung vorsichtig vom unteren Geh use abheben Dabei auf das Kabel achten das an der Hauptplatinenbaugruppe angeschlossen ist Das Kabel von der Hauptplatinenbaugruppe entfernen und die obere Abdeckung beiseite legen Die 2 Schrauben mit denen die COM2 Abdeckplatte hinten und rechts vom unteren Geh use befestigt ist entfernen siehe Abbildung 2B Die Abdeckplatte und 2 Schrauben entsorgen Die zweite USB Platine ber den entsprechenden St ndern montieren dann mit den zwei mitgelieferten Schrauben befestigen siehe Abbildung 2C Das Platinenkabel a mit der zweiten USB Platine und b mit dem Anschluss CN6 auf der Hauptplatine auf der Vorderseite der Waage verbinden siehe Abbildung 2D Das Platinenkabel in Richtung linke Seite des unteren Geh uses f hren Die Waage in umgekehrter Reihenfolge wieder zusammenbauen Dabei darauf achten dass keine Kabel im oder zwischen dem oberen und unteren Geh use gequetscht werden DE 4 USB Schnittstelleno
42. the balance from the mains power supply and remove any installed batteries before beginning installation e Internal components such as the load cell and printed circuit boards PCB are delicate and need to be handled with care e Do not subject the internal components to static electricity discharge e The PCB s should be handled by grasping the edges only and never placing fingers on any of the runs or traces 2 2 Hardware Installation The Adventurer Pro series comes in different configurations see Figures 1A B C Disassemble assemble the balance according to the configuration that matches your model EN 2 USB Interface Kit Draft Shield Cover Draft Shield Pan Pan Support Fan Wind Ring Adapter Ring EMC Plate Pan Support EMC Plate Cover Screws 2 Cover Screws 2 CA 2 02 over Screws 2 d Ss EMC Plate m a Figure 1B Glass Doors a a Cover Screws 2 Figure 1C 1 USB Interface Kit EN 3 With power removed from the balance remove any draft shield or draft shield glass panels the pan pan support and any wind ring or adapter ring sizes and shapes vary to fully expose the EMC plate on the top of the balance Remove the 2 screws and the EMC plate NOTE On some models with angular wind rings be careful not to lose the 4 corner plastic locating pins where the EMC plate slots over These are marked F front or B back with the markings
43. therdware configurations Hardware Profiles Ges on Ges n El puerto serial USB puede encontrarse bajo Ports COM amp LPT en la ventana de Administrador de dispositivos En el caso de la fotograf a mostrada abajo la ventana de Administrador de dispositivos muestra un n mero de puerto COM del puerto serial USB como COM3 El numero del puerto COM que se muestra en esta ventana es el n mero de puerto COM que la aplicaci n PC utilizar para comunicarse con la balanza ES 8 Paquete de interfaz USB ll File Action View Help e mj amp glm E Y Computer Hs Disk drives H 9 Display adapters Fl DVD CD ROM drives Floppy disk controllers Id Floppy disk drives H 6 Human Interface Devices H E IDE ATA ATAPI controllers H Keyboards El Mice and other pointing devices El 3 Monitors 9 Network adapters EH Ports COM amp LPT I Communications Port COM1 I Communications Port COM2 Y ECP Printer Port LPT1 4 USB Serial Port COM3 EM Processors E Sound video and game controllers System devices El Universal Serial Bus controllers zl Nota Cuando utilice la interfase USB con programas que limiten el n mero de designaciones de los puertos COM por ejemplo Ohaus MassTracker s lo permite los puertos COM1 2 3 y 4 puede ser necesario asignar uno de estos n meros de puerto al nuevo puerto virtual Para cambiar el n mero de puerto asignado al puerto se
Download Pdf Manuals
Related Search