Home
BF-MM and BK-MM Cultivator MultiTools Instruction Manual
Contents
1. BK MM cultivator blades with curved tines FC MM edger RL MM aerator MF MM dethatcher A Warning The MultiTool must be properly tight ened and in safe operating condition Inspect for loose parts hitch pins Screws etc and for cracked bent warped or damaged blades Replace damaged blades before using the power tool English A Warning Do not attach any MultiTool to a unit without proper installation of all required parts Failure to use the proper parts may cause the attachments to fly off and seriously injure the operator or bystanders A Warning To reduce the risk of injury from thrown objects and contact with the attachment never operate your power tool without a properly mounted deflector Check your MultiTool instruction man ual to ensure you are using the appropriate deflector for the MultiTool mounted Starting A Warning Start the engine at least 10 feet 3 m from the fueling spot outdoors only For specific starting instructions see the appropriate section of your MultiEngine and MultiTool manuals Place the power tool on firm ground or other solid surface in an open area Maintain good balance and secure footing x N e e lt a o A Warning Always stand to one side of the unit to avoid the risk of injury from contact with the rotating MultiTool A Warning To reduce the risk of injury from loss of control be absolutely sure that t
2. 2 Sentido de giro 3 de la MultiTool Ajuste de la posici n de la caja de engranajes A e Afloje los tornillos de fijaci n en la caja de engranajes 481BA011 KN e Gire la caja de engranajes en 180 e Alinee la caja de engranajes en la posici n correcta e Apriete los dos tornillos de fijaci n en la caja de engranajes en la siguiente secuencia Apriete el primer tornillo moderadamente Apriete el segundo tornillo moderadamente BF MM BK MM Apriete el primer tornillo firmemente Apriete el segundo tornillo firmemente lt gt No debe ser posible girar el mecanismo en el tubo de mando Montaje de la MultiTool e Arregle las cuchillas en la secuencia de instalaci n en el eje observando los siguientes puntos Las cuchillas izquierdas y derechas son diferentes El sentido de giro est marcado con flechas en la caja de engranajes y en las cuchillas o e eo X a o Re e Gire la cuchilla derecha interior 4 en el eje hasta que sea posible empujarla a su posici n Verifique otra vez el sentido de giro flechas La cuchilla giratoria interior tiene un cubo m s grande que el de la cuchilla exterior BF MM BK MM Gire la cuchilla derecha exterior 5 en el eje hasta que sea posible empujarla a su posici n Verifique otra vez el sentido de giro flechas Coloque y enganche el pasador de enga
3. ndoles soldadura enderez ndo los o modific ndoles su forma Esto puede causar el desprendimiento de alguna pieza del accesorio y producir lesiones graves o mortales Apriete todas las tuercas pernos y tornillos excepto los tornillos de ajuste del carburador despu s de cada uso No limpie la m quina con una lavadora a presi n El chorro fuerte de agua puede da ar las piezas de la m quina espa ol EE UU Guarde la herramienta motorizada en un lugar seco y elevado o con llave lejos del alcance de los ni os 25 espa ol EE UU Uso Generalidades Las cultivadoras MultiTool est n disponibles en versiones con puas ganz as BFMM y p as bolo BKMM 26 P as ganz as 469BA017 KN Las p as ganz as son particularmente tiles para labrar y soltar suelos duros compactados y con materiales incrustados P as bolo z eo 2 lt ao o e t No disponible en todos los mercados Las p as bolo son particularmente tiles para labrar suelos cultivados y mas blandos Preparaciones e Fije el manillar en la posici n de trabajo normal e Arranque el motor T cnica de trabajo 469BA016 KN El motor MultiEngine con cuchillas giratorias puede ponerse en marcha en sentido de avance 1 o retroceso 2 Elija el mejor m todo y tipo de cuchilla giratoria para su trabajo es decir dependiendo de la forma y tama o del lugar de trabajo y las condiciones del
4. suelo Si se trabaja alternando el sentido hacia adelante y hacia atr s esto resulta particularmente til para soltar la tierra compactada Un movimiento consistente en sentido hacia delante o hacia atr s resulta til para trabajar con suelos sueltos Las cuchillas giratorias s lo pueden montarse y accionarse en una posici n Las flechas en las cuchillas indican el sentido de rotaci n que requieren consulte el cap tulo Montaje de la MultiTool Usos t picos e Rotura del suelo BF MM BK MM Hay que hacer unos pocos trabajos preparativos antes de empezar a romper el suelo previamente cultivado por ejemplo en el jard n del afio pasado Primero quite las malezas de la superficie y los restos de los dem s cultivos as como los objetos duros tales como rocas piedras botellas pedazos de madera etc Agarre la cultivadora firmemente con ambas manos y cultive a la profundidad deseada solamente una zona peque a ala vez Termine el cultivo guiando la cultivadora para evitar dejar huellas Use un rastrillo para nivelar la zona de trabajo e Aflojado del suelo alrededor de los cultivos z x o A 2 lt gt oO o O Afloje nicamente la tierra superficial alrededor de las plantas No trabaje demasiado profundo ya que esto puede dafiar las ra ces poca profundas de algunos cultivos BF MM BK MM Para evitar da ar la cultivadora o los rboles procure no enganchar las cuchill
5. 0 or STOP A Warning The MultiTool continues to rotate for a short period after the throttle trigger is released flywheel effect English If the MultiTool or deflector becomes clogged or stuck always switch off the engine and make sure the attachment has stopped before cleaning Grass weeds etc should be cleaned off the a 5m 16ft attachment as necessary E Toreduce the risk of eye and other injury ensure that bystanders are at least 16 feet 5 m away Bystanders should be encouraged to wear eye protection To reduce the risk of damage to property also maintain this distance from such objects as vehicles or windows Stop the engine immediately if you are approached A Warning Before you start work examine the area for stones glass pieces of metal rub bish or other solid objects Such objects could be hurled by the cutting tool and directly or indirectly strike the operator or bystanders Such objects may also damage the MultiTool The blade may shatter splinter or break Flying objects or damaged blades may cause serious or fatal injury to the operator and bystanders A Warning Never divert discharge of material toward bystanders nor allow anyone near the area of operation Use care in directing discharge to avoid damage to surfaces automobiles and the like A Warning Avoid cutting close to fences sides of buildings tree trunks stones or similar obstacles which co
6. adicionales acerca de la ropa adecuada vea las precauciones de seguridad en el manual de instrucciones del accesorio MultiEngine que est usando LA HERRAMIENTA MOTORIZADA MOTOR MULTIENGINE PROVISTO CON CULTIVADORA MULTITOOL Para las ilustraciones y definiciones de los componentes de la herramienta motorizada vea el cap tulo sobre Piezas principales BF MM BK MM Advertencia Nunca modifique de ninguna manera esta herramienta motorizada Utilice nicamente los accesorios suministra dos por STIHL y expresamente autorizados por STIHL para usarse con los modelos espec ficos de herramien tas motorizadas de STIHL Si bien es posible conectar a la herramienta moto rizada de STIHL ciertos accesorios no autorizados su uso puede ser en la pr ctica extremadamente peligroso Si la m quina experimenta cargas excesivas para las cuales no fue disefiada por ejemplo impactos Severos o una ca da siempre aseg rese de que la m quina est en buenas condiciones antes de seguir con el trabajo Inspeccione espec ficamente la integridad del sistema de combustible ausencia de fugas y aseg rese de que los controles y dispositivos de seguridad funcionen como es debido No siga manejando esta m quina si est da ada En caso de dudas pida que el concesionario de servicio de STIHL la revise BF MM BK MM EL USO DE LA HERRAMIENTA MOTORIZADA MOTOR MULTIENGINE EQUIPADO CON CULTIVADORA MULTITOOL Transporte
7. de la herramienta motorizada Advertencia Para reducir el riesgo de sufrir lesiones debido a la p rdida de control y al con tacto con la cuchilla nunca lleve ni transporte la herramienta motorizada con el MultiTool en marcha Advertencia Antes de apoyar la herramienta motori zada en el suelo siempre apague el motor y aseg rese de que la MultiTool ha dejado de girar 469BA001 KN Sujete la herramienta motorizada por su argolla de transporte con el accesorio hacia delante Advertencia Cuando transporte la m quina en un veh culo suj tela firmemente para impedir su vuelco el derrame de com bustible y el dafio a la m quina espa ol EE UU Antes de arrancar Advertencia Siempre revise que la herramienta motorizada est en buenas condiciones y funcione correctamente antes de arrancarla Nunca intente modificar los controles o los dispositivos de seguridad Advertencia No maneje nunca una herramienta motorizada que est dafiada mal ajus tada o mantenida o que no fue armada completa y debidamente Despliegue el manillar tipo bicicleta a la posici n de trabajo y aseg relo con la perilla consulte el cap tulo Ajuste del manillar tipo bicicleta del manual de instrucciones del motor MultiEngine Mantenga los mangos limpios y secos en todo momento es particularmente importante mantenerlos libres de humedad aceite combustible grasa o resinas para garantizar que
8. grown terrain Watch for hidden obstacles such as tree stumps roots and ditches to avoid stumbling For bet ter footing clear away scrub and cuttings Be extremely cautious when working on slopes or uneven ground Operate the power tool only at a normal walking pace A Warning To avoid the risk of injury from contact with the rotating attachment be extremely cautious when pulling the power tool toward you Be extremely cautious when changing direction with the power tool especially on slopes A Warning To avoid the risk of injury from loss of control never work on steep slopes Working Conditions Start and operate your power tool only outdoors in a well ventilated area Operate it under good visibility and daylight conditions only Work carefully BF MM BK MM A Warning If the soil being worked on or the sur rounding ground is coated with a chemical substance such as an active pesticide or herbicide read and follow the instructions and warnings that accompany the substance at issue A Warning Inhalation of certain dusts especially organic dusts such as mold or pollen can cause sus ceptible persons to have an allergic or asthmatic reaction Substantial or repeated inhala tion of dust and other airborne contaminants in particular those with a smaller particle size may cause respira tory or other illnesses Control dust at the source where possible Use good work practices such
9. la m quina pueda empu arse firmemente para mantenerla bajo control seguro Advertencia Para reducir el riesgo de lesiones cau sadas por el giro de la herramienta MultiTool en sentido incorrecto aseg rese que la posici n de la caja de engranajes sea la correcta y cambie su posici n seg n se requiera 21 espa ol EE UU En las herramientas de metal ilustraci n superior coloque la caja de engranajes de modo que el eje est debajo del tubo de mando Se usa en Hojas de cultivadora BF MM con p as puntiagudas Hojas de cultivadora BK MM con p as curvas Cortaborde FC MM Aireador RL MM Quitamusgos MF MM Advertencia La MultiTool debe estar correctamente apretada y en buenas condiciones de trabajo Busque piezas sueltas pasa dores de enganche tornillos etc y cuchillas agrietadas dobladas defor madas o da adas Sustituya las cuchillas da adas antes de usar la herramienta motorizada 22 Advertencia No instale ninguna MultiTool en una m quina sin que todas las piezas requeridas est n correctamente instala das Si no se utilizan las piezas debidas Se puede causar el desprendimiento de los accesorios y lesionar gravemente al operador o a las personas que encuen tren en su proximidad Advertencia Para reducir el riesgo de lesiones cau sadas por objetos arrojados y contacto con la cuchilla nunca maneje una herramienta motoriza
10. los dem s trabajos de reparaci n Los reclamos de garant a presentados despu s de realizadas las reparaciones ser n aceptados nicamente si las mismas fueron ejecutadas por un concesionario de servicio autorizado STIHL utilizando piezas de repuesto originales de STIHL Es posible identificar las piezas originales de STIHL por el n mero de pieza STIHL el logotipo de S TIAL y en ciertos casos el s mbolo 57 de piezas STIHL En las piezas peque as el s mbolo puede aparecer solo BF MM BK MM Marcas comerciales Marcas registradas de STIHL STIHL STIHL 87 La combinaci n de colores anaranjado gris N meros de registro EE UU 2 821 860 3 010 057 3 010 058 3 400 477 y 3 400 476 e 4 MIXO AUTOCUT EASYSTART FARM BOSS iCademy OILOMATIC STIHL Cutquik STIHL DUROMATIC STIHL Quickstop STIHL ROLLOMATIC STIHL WOOD BOSS TIMBERSPORTS WOOD Boss YARD BOSS BF MM BK MM Algunos de las marcas comerciales de STIHL por ley comun TETIAL BioPlus Easy2Start EasySpool ElastoStart Ematic FixCut HT Plus IntelliCarb Master Control Lever Micro Pro Mark Quad Power Quiet Line STIHL Compact STIHL HomeScaper Series STIHL Interchangeable Attachment Series STIHL M Tronic STIHL Magnum STIHL MiniBoss STIHL MotoPlus 4 STIHL Multi Cut HomeScaper Series Stihl Outfitters STIHL PICCO STIHL Poly
11. tan pronto que arranque el motor Por esta raz n accione moment neamente el gatillo de aceleraci n el motor reduce su aceleraci n al r gimen de marcha en vac o Ahora siga el procedimiento de arranque descrito en el manual de instrucciones del motor MultiEngine Para apagar el motor e Consulte el manual de instrucciones del motor MultiEngine 30 Almacenamiento de la m quina Para intervalos de 3 meses o m s e Retire limpie e inspeccione las cuchillas giratorias e Guarde la m quina en un lugar seco y elevado o bajo llave fuera del alcance de los ni os y de otras personas no autorizadas Informaci n para mantenimiento Los intervalos dados a continuaci n corresponden nicamente a condiciones normales de trabajo Si el tiempo de trabajo por jornada es m s largo que lo normal o si las condiciones son extremas zonas polvorientas etc acorte los intervalos indicados de modo correspondiente Todos los tornillos y tuercas accesibles e Vuelva a apretarlos de ser necesario Accesorios de barrido y deflectores e Inspeccione revise el apriete antes de comenzar el trabajo y despu s de cada parada para cargar combustible e Sustituya si est da ado Etiquetas de seguridad e Cambie las etiquetas de seguridad ilegibles BF MM BK MM espafiol EE UU Componentes importantes 1 Cuchilla cultivadora exterior derecha 2 Cuchilla cultivadora interior derecha 3 Cuchilla cultiv
12. Cut STIHL PowerSweep espafiol EE UU STIHL Precision Series STIHL Protech STIHL RAPID STIHL SuperCut STIHL Territory TapAction TrimCut Esta lista de marcas comerciales esta sujeta a cambios Queda terminantemente prohibido todo uso de estas marcas comerciales sin el consentimiento expreso por escrito de ANDREAS STIHL AG amp Co KG Waiblingen 33 espa ol EE UU 34 BF MM BK MM espa ol EE UU BF MM BK MM 35 espa ol EE UU 36 BF MM BK MM 0458 484 8621 englisch spanisch USA 0458 484 8621
13. STIHL BF MM BK MM STIHL Instruction Manual Manual de instrucciones Warning Read and follow all safety precautions in Instruction Manual improper use can cause serious or fatal injury Advertencia Lea y siga todas las precauciones de seguridad dadas en el manual de instrucciones el uso incorrecto puede causar lesiones graves o mortales Instruction Manual 1 16 Manual de instrucciones 17 33 Contents MultiSystem Guide to Using this Manual Safety Precautions and Working Techniques Using the Unit Approved MultiEngines Mounting the MultiTool Starting Stopping the Engine Storing the Machine Maintenance and Care Main Parts Specifications Maintenance and Repairs Trademarks Original Instruction Manual Printing inks contain vegetable oils paper can be recycled Printed on chlorine free paper ANDREAS STIHL AG amp Co KG 2011 0458 484 8621 M2 C11 PM 0000000545_001_GB STIHL BF MM BK MM 11 11 12 13 13 14 15 15 15 English Allow only persons who fully understand the manuals of the MultiEngine and soil cultivator MultiTool to operate this power tool combination To receive maximum performance and satisfaction from your STIHL MultiTool it is important that you read understand and follow the safety precautions and the operating and maintenance instructions in chapter Safety Precautions and Working Techniques before using your MultiTool For further inform
14. adora interior izquierda 4 Cuchilla cultivadora exterior izquierda 5 Pasador de enganche Definiciones 1 Cuchilla cultivadora exterior derecha Cuchilla met lica forma de estrella con p as apuntadas o curvadas Para colocar en el exterior del lado derecho 2 Cuchilla cultivadora interior derecha Cuchilla met lica forma de estrella con p as apuntadas o curvadas Para colocar en el interior del lado derecho 3 Cuchilla cultivadora interior izquierda Cuchilla met lica forma de estrella con p as apuntadas o curvadas Para colocar en el interior del lado izquierdo 4 Cuchilla cultivadora exterior izquierda Cuchilla met lica forma de estrella con p as apuntadas o curvadas Para colocar en el exterior del lado izquierdo 484BA001 KN BF MM BK MM 31 espa ol EE UU 5 32 Pasador de enganche Fije los accesorios y facilita el retiro y la instalaci n de los mismos Especificaciones Accesorio Cuatro cuchillas con filo doble giran en un mismo sentido Di metro de puas ganzuas 230 mm 9 1 pulg Diametro de puas bolo 210 mm 8 3 pulg Ancho de trabajo 220 mm 8 7 pulg Peso Cuatro cuchillas giratorias con cubo P as ganzuas 2 0 kg 4 4 Ib Puas bolo 2 0 kg 4 4 Ib Informaci n de reparaci n Los usuarios de esta m quina deben efectuar nicamente los trabajos de mantenimiento descritos en este manual Solamente los talleres autorizados por STIHL deben llevar a cabo
15. all foreign objects stones glass wire etc thrown back by the rotating attachment Thrown objects may also ricochet and strike the operator A Warning To reduce the risk of gt injury to your eyes never operate your power tool unless wearing goggles or properly fitted protec tive glasses with adequate top and side protection com plying with ANSI Z 87 1 or your applicable national standard To reduce the risk of injury to your face STIHL recommends that you also wear a face shield or face screen over your goggles or protective glasses Power tool noise may damage your hearing Wear sound barriers ear plugs or ear mufflers to protect your hearing Continual and regular users should have their hearing checked regularly Be particularly alert and cautious when wearing hearing protection because your ability to hear warnings shouts alarms etc is restricted Always wear gloves when handling the power tool and the attachment Heavy duty nonslip gloves improve your grip and help to protect your hands Clothing must be sturdy and snug fitting but allow complete freedom of movement Wear long pants made of heavy material to help protect your legs Do not wear shorts sandals or go barefoot Avoid loose fitting jackets scarfs neckties jewelry flared or cuffed pants unconfined long hair or anything that could become caught on branches brush or the moving parts of the unit Secure hair so
16. as en las ra ces grandes de los rboles e Incorporaci n de mejoradores del suelo La cultivadora puede usarse para la incorporaci n de marga tierra de jardinero hojas u otros materiales org nicos o fertilizantes Prepare la zona quitando las ra ces viejas los restos de plantas grandes y objetos duros rocas etc Esparza el mullido uniformemente sobre el suelo Incorpore el mullido con un movimiento hacia adelante y atr s Termine el trabajo nivelando la zona con un rastrillo e Zanjeo o apertura de surcos Camine lentamente hacia atr s y tire de la cultivadora para formar el surco requerido Repita seg n sea necesario para formar surcos m s profundos Limpieza de las cuchillas giratorias Las piezas de plantas tales como las ra ces pueden enrollarse alrededor de las cuchillas giratorias o entre las mismas durante el trabajo Para limpiar las cuchillas giratorias Use guantes Extraiga los pasadores de enganche del eje Extraiga las cuchillas giratorias del eje Quite las ra ces plantas y tierra espa ol EE UU Consulte la secci n Montaje de la herramienta MultiTool para las instrucciones de montaje Espuela cultivadora accesorio especial La espuela simplifica el control de la m quina y reduce la fatiga causada por el uso de la herramienta Frena el movimiento hacia adelante y reduce el esfuerzo necesario para sujetar la herramienta motorizada La e
17. as en zonas pedregosas Utilice su motor MultiEngine equipado con una cultivadora Multi Tool solamente para rejuvenecer canteros o lechos de flores y plantas as como para incorporar los aditivos de mejora del suelo espa ol EE UU Advertencia No debe usarse para ning n otro prop sito ya que el uso indebido puede resultar en lesiones personales o da os a la propiedad incluso da os de la m quina Advertencia Nunca se debe permitir a los ni os que usen esta herramienta motorizada No se debe permitir la proximidad de otros especialmente ni os y animales donde se est utilizando la m quina Advertencia Para reducir el riesgo de ocasionar lesiones a las personas en la cercan a y dafios a la propiedad nunca deje la herramienta motorizada en marcha desatendida Cuando no est en uso por ejemplo durante el descanso ap guela y aseg rese de que las personas no autorizadas no puedan usarla Las medidas de seguridad y avisos contenidos en este manual se refieren al uso de todas las herramientas motorizadas STIHL Los distintos modelos pueden contar con piezas y controles diferentes Vea la secci n correspondiente de sus manuales de instrucciones del motor MultiEngine y accesorio MultiTool para tener una descripci n de los controles y la funci n de los componentes de su modelo El uso seguro de una herramienta motorizada ata e a 19 espa ol EE UU 1 eloperador 2 la herrami
18. as operating the unit so that the wind or operating proc ess directs any dust raised by the power tool away from the operator Follow the recommendations of EPA OSHA NIOSH and occupational and trade associations with respect to dust par ticulate matter When the inhalation of dust cannot be substantially controlled i e kept at or near the ambient back ground level the operator and any bystanders should wear a respirator approved by NIOSH MSHA for the type of dust encountered English A Danger Your power tool is not insulated against electric shock To reduce the risk of electrocution ensure that there are no power cables near the surface or in the working area that could come into contact with the MultiTool Damag ing such cables with the tool can cause electric shocks with serious or fatal consequences Information on the routing of cables can be obtained from public utilities and such service providers as Miss Utility or One Call A Warning Use the power tool at ground level only The risk of injury is increased if you use MultiTools above ground level because they are more exposed and the power tool is more difficult to control Operating Instructions A Warning Do not operate your power tool using the starting throttle lock as you do not have control of the engine speed In the event of an emergency switch off the engine immediately move the slide control stop switch to
19. ation you can go to www stihlusa com Contact your STIHL dealer or the STIHL distributor for your area if you do not understand any of the instructions in the two manuals A Warning Because a MultiEngine equipped with a soil cultivator MultiTool is a power tool with a relatively fast turning attachment some special safety precautions must be observed to reduce the risk of per sonal injury Careless or improper use may cause serious or even fatal injury English MultiSystem zZ eo a lt co D In the STIHL MultiSystem various MultiEngines and MultiTools are combined to form a machine In this Instruction Manual the functional unit of MultiEngine and MultiTool is referred to as a machine Accordingly the instruction manuals for the MultiEngine and the MultiTool constitute the entire Instruction Manual for the machine Always read both manuals carefully before using your machine for the first time and keep them safe for future reference Guide to Using this Manual Pictograms All the pictograms attached to or embossed on the machine are shown and explained in this manual Symbols in Text Many operating and safety instructions are supported by illustrations The individual steps or procedures described in the manual may be marked in different ways e A bullet marks a step or procedure A description of a step or procedure that refers directly to an illustration may contain it
20. d right hand blades are different The direction of rotation is marked with arrows on the gearbox and blades z D eu o X a o Re e Rotate the inner right hand blade 4 on the shaft until it can be pushed into position check the direction of rotation again arrows The hub of the inner blade is larger than that of the outer blade e Rotate the outer right hand blade 5 on the shaft until it can be pushed into position check the direction of rotation again arrows e Insert and engage the hitch pin 6 in the hole in the shaft fold the hitch pin flat against the blade e Use the same procedure to mount the rotor blades on the left hand side 12 Starting Stopping the Engine Starting the Engine Always follow the starting procedure described in the MultiEngine instruction manual x e e e lt ad o Secure the handlebar in the normal operating position e Retract the wheels if fitted see chapter on Wheels in MultiEngine instruction manual e Retract the spur if fitted e Place the unit on the ground Check that the blades are not touching the ground or any other obstacles The unit must rest on the engine flange and the support on the frame Make sure you have good balance and secure footing as shown in the illustration To reduce the risk of injury from contact with the rotating blades always stand to the side of the powe
21. da sin que tenga instalado debidamente el deflector Consulte el manual de instrucciones de MultiTool para comprobar que se est usando el deflector adecuado para la MultiTool en uso Arranque Advertencia Arranque el motor al aire libre por lo menos 3 m 10 pies del lugar en que lo haya llenado Para las instrucciones espec ficas de arranque vea la secci n correspondiente de los manuales del motor MultiEngine y accesorio MultiTool Coloque la herramienta motorizada Sobre suelo firme u otra superficie s lida en un lugar abierto Mantenga el equilibrio y elija un buen punto de apoyo para los pies z x N a o lt ch o o t Advertencia Siempre p rese a un lado de la m quina para evitar los riesgos de lesiones causadas por el contacto con la MultiTool en movimiento Advertencia Para reducir el riesgo de lesiones debido a la p rdida de control est absolutamente seguro que la MultiTool se encuentra lejos de su cuerpo y de todas las obstrucciones y objetos incluido el suelo porque al arrancar el motor acelerado su velocidad ser lo suficientemente r pida para que el embrague se engrane y mueva la MultiTool Tan pronto arranque accione inmediatamente por un breve momento el gatillo de aceleraci n para desconectarlo de la posici n de arranque y permitir que el motor se desacelere a la marcha en vac o Advertencia Su herramienta motorizada es una m quina que deb
22. e Inner Left Hand Cultivator Blade Outer Left Hand Cultivator Blade Hitch Pin Definitions Outer Right Hand Cultivator Blade Metal blade star shaped with pointed or curved tines Mounts to the outer right hand side Inner Right Hand Cultivator Blade Metal blade star shaped with pointed or curved tines Mounts to the inner right hand side Inner Left Hand Cultivator Blade Metal blade star shaped with pointed or curved tines Mounts to the inner left hand side Outer Left Hand Cultivator Blade Metal blade star shaped with pointed or curved tines Mounts to the outer left hand side Hitch Pin Secures the attachments and simplifies removal and installation of the attachments BF MM BK MM Specifications Attachment Four rotor blades double edged rotate in same direction Diameter of pick tine 9 1 in 230 mm Diameter of bolo tine 8 3 in 210 mm Working width 8 7 in 220 mm Weight Four rotor blades with hub Pick tines 4 4 lbs 2 0 kg Bolo tines 4 4 lbs 2 0 kg BF MM BK MM Maintenance and Repairs Users of this unit should carry out only the maintenance operations described in this manual Other repair work may be performed only by authorized STIHL service shops Warranty claims following repairs can be accepted only if the repair has been performed by an authorized STIHL servicing dealer using original STIHL replacement parts Original STIHL parts can be identified by
23. e ser manejada por solamente una persona No deje que otras personas est n en el lugar de tra bajo aun durante el arranque BF MM BK MM Vea tambi n las precauciones de seguridad de arranque en el manual de instrucciones del motor MultiEngine Durante el trabajo Sujecion y control de la herramienta motorizada 469BA045 KN Al trabajar siempre sujete la maquina firmemente con ambas manos en los mangos Envuelva los dedos firmemente en los mangos manteni ndolos sujetos entre los dedos indice y pulgar Mantenga las manos en esta posici n para que siempre tenga la herramienta motorizada bien controlada Advertencia Nunca intente manejar la herramienta motori zada con una sola mano La p rdida de control de la herra mienta motorizada puede ocasionar lesiones graves o mor tales Para reducir el riesgo de lesionarse mantenga las manos y los pies alejados de la MultiTool No toque nunca con las manos o cualquier parte del cuerpo la MultiTool est en movimiento BF MM BK MM Advertencia No trate de alcanzar m s lejos de lo debido Mantenga los pies bien apoya dos y equilibrados en todo momento Se debe tener cuidado especial cuando las condiciones del suelo son resbaladizas suelo humedo nieve y en terreno dif cil y con mucha vegetaci n Para evitar tropezarse est atento a los obst culos ocultos tales como tocones ra ces y zanjas Para obtener un punto de apoyo seguro quite l
24. em numbers that appear in the illustration Example e Loosen the screw 1 e Lever 2 In addition to the operating instructions this manual may contain paragraphs that require your special attention Such paragraphs are marked with the symbols and signal words described below A Danger Indicates an imminent risk of severe or fatal injury A Warning Indicates a hazardous situation which if not avoided could result in severe or fatal injury Caution Indicates a risk of property damage including damage to the machine or its individual components Engineering Improvements STIHL s philosophy is to continually improve all of its products As a result engineering changes and improvements are made from time to time Therefore some changes modifications and improvements may not be covered in this manual If the operating characteristics or the appearance of your machine differ from those described in this manual please contact your STIHL dealer for assistance BF MM BK MM Safety Precautions and Working Techniques Because a MultiEngine equipped with a soil cultivator MultiTool is a high speed power tool special safety precau tions must be observed to reduce the risk of per sonal injury It is important that you read fully understand and observe the following safety precautions and warnings Read the instruction manuals and the safety precautions of your MultiEngine and MultiTool peri
25. encia Durante el corte revise el apriete y la condici n de la MultiTool en intervalos regulares Si nota un cambio en el com portamiento del accesorio apague el motor inmediatamente y revise el acce sorio Sustituya inmediatamente una cuchilla trizada combada deformada o dafiada incluso si solamente hay rayas superficiales Los accesorios en esa condici n pueden romperse a alta velo cidad y causar lesiones graves o mortales Advertencia La caja de engranajes est caliente durante el funcionamiento de la m quina Para reducir el riesgo de lesiones por quemaduras no toque la caja de engranajes cuando est caliente BF MM BK MM MANTENIMIENTO REPARACI N Y ALMACENAMIENTO Advertencia Siempre apague el motor y verifique que el accesorio est parado antes de llevar a cabo cualquier trabajo de man tenimiento reparaci n o limpieza de la herramienta motorizada No intente hacer ning n trabajo de mantenimiento o reparaci n que no est descrito en su manual de instrucciones del motor Mul tiEngine o de la MultiTool Este tipo de trabajo debe realizarse nicamente en el taller de servicio de STIHL Advertencia Utilice solamente piezas de repuesto de STIHL para el mantenimiento y la repa raci n El uso de piezas no fabricadas por STIHL puede causar lesiones gra ves o mortales Use guantes para manipular o reparar las cuchillas Advertencia Nunca repare los accesorios da ados aplic
26. enta motorizada el uso de la herramienta motorizada EL OPERADOR Condici n f sica Usted debe estar en buenas condiciones f sicas y ps quicas y no encontrarse bajo la influencia de ninguna sustancia drogas alcohol etc que le pueda restar visibilidad destreza o juicio No maneje esta m quina cuando est fatigado Advertencia Est alerta Si se cansa t mese un des canso El cansancio puede provocar una p rdida del control El uso de cual quier herramienta motorizada es fatigoso Si usted padece de alguna dolencia que pueda ser agravada por la fatiga consulte a su m dico antes de utilizar esta m quina Vestimenta adecuada Advertencia Para reducir el riesgo de lesiones el operador debe usar el equipo protector adecuado El deflector adecuado para su herramienta motorizada no siempre protege al operador contra todos los objetos extrafios piedras vidrio alambre etc arrojados por el accesorio 20 de corte giratorio Los objetos arrojados o lanzados por el accesorio tambi n pueden rebotar y golpear al operador Advertencia Para reducir el riesgo de lesionarse los ojos nunca maneje la herra mienta motorizada si no Nx tiene puestas gafas o anteojos de seguridad bien ajustados con una protecci n ade cuada en las partes superior y laterales que satisfagan la norma ANSI Z 87 1 o la norma nacional correspondiente Para reducir el riesgo de lesionarse la cara STIHL rec
27. erencia que aparecen en la ilustraci n Ejemplo e Suelte el tornillo 1 e Palanca 2 Adem s de las instrucciones de uso en este manual pueden encontrarse p rrafos a los que usted debe prestar atenci n especial Tales p rrafos est n marcados con los s mbolos y las palabras identificadoras que se describen a continuaci n Peligro Indica un riesgo inminente de lesiones graves o mortales Advertencia Identifica una situaci n de peligro que al no evitarse puede resultar en lesio nes graves o mortales jPrecaucion Indica el riesgo de da os a la propie dad incluyendo a la m quina o sus componentes Mejoramientos t cnicos La filosof a de STIHL es mejorar continuamente todos sus productos Como resultado de ello peri dicamente se introducen cambios de dise o y mejoras Por lo tanto es posible que algunos cambios modificaciones y mejoras no se describen en este manual Si las caracter sticas de funcionamiento o la apariencia de su m quina difieren de las descritas en este manual comun quese con el concesionario STIHL para obtener la ayuda que requiera BF MM BK MM Medidas de seguridad y t cnicas de manejo Dado que un motor Mul tiEngine equipado con una cultivadora MultiTool es un aparato motorizado que funciona a velocidad r pida es necesario tomar medidas especia les de seguridad para reducir el riesgo de lesiones Es importante que usted lea comprenda bien
28. esiones aumenta al usar la MultiTool Sobre el nivel del suelo ya que quedan m s al descubierto y puede ser m s dif cil de controlar Instrucciones de manejo Advertencia No maneje la herramienta motorizada usando el bloqueo de acelerador para arranque pues no tendr control de la velocidad del motor En caso de emergencia apague el motor inmediatamente mueva el control deslizante interruptor de parada a 0 o STOP 24 Advertencia La MultiTool sigue girando por un rato despu s que se suelta el gatillo de ace leraci n efecto de volante Si la MultiTool o el deflector se atasca o queda pegado siempre apague el motor y aseg rese que el accesorio barredor est detenido antes de limpiarlo Limpie el pasto las malezas etc del accesorio seg n sea necesario 5m 16ft e Para reducir el riesgo de ocasionar lesiones a los ojos u otras partes del cuerpo aseg rese que las personas est n a por lo menos 5 m 16 pies de distancia de la m quina Se debe aconsejar a las personas que se encuentran cerca de la m quina que usen protecci n de los ojos Para reducir el riesgo de ocasionar da os a la propiedad mantenga esta distancia con respecto a los veh culos y las ventanas Apague el motor inmediatamente si se le aproxima alguna persona Advertencia Antes de empezar a trabajar inspec cione el rea en busca de piedras vidrio pedazos de metal basura u otros obje
29. he MultiTool is clear of you and all other obstructions and objects including the ground because when the engine starts at starting throttle engine speed will be fast enough for the clutch to engage and move the MultiTool Once the engine has started immediately blip the throttle trigger which should release the starting throttle and allow the engine to slow down to idle A Warning Your power tool is a one person machine Do not allow other persons in the general work area even when starting See also the safety precautions on Starting in the instruction manual of the MultiEngine During Operation Holding and Controlling the Power Tool 469BA045 KN Always hold the unit firmly with both hands on the handles while you are working Wrap your fingers and thumbs around the handles keeping the handles cradled between your thumb and forefinger Keep your hands in this position to have your power tool under control at all times A Warning Never attempt to oper ate your power tool with one hand Loss of con trol of the power tool may result in serious or fatal injury To reduce the risk of injury keep hands and feet away from the MultiTool Never touch a moving MultiTool with your hand or any other part of your body BF MM BK MM A Warning Do not overreach Keep proper footing and balance at all times Special care must be taken in slippery conditions wet ground snow and in difficult over
30. ine BF MM BK MM Mounting the MultiTool Removing Existing MultiTools Wear gloves to reduce the risk of injury from contact with sharp MultiTools and or hot surface of gearbox z eo e eo lt ao t Remove the hitch pin and pull the MultiTools if fitted off the shaft see also Mounting the MultiTool in the instruction manual of the other MultiTool Clean the gearbox if necessary Checking Position of Gearbox To reduce risk of injury from the MultiTool rotating in the wrong direction check that position of gearbox is correct and adjust if necessary English 2 mt li JAS oT lo 1 nA 3 3 5 Gearbox output shaft 1 below the drive tube 2 Direction of rotation 3 of MultiTool Adjusting Position of Gearbox 481BA011 KN Loosen clamp screws on gearbox Turn the gearbox through 180 e Lineup the gearbox in the correct position Tighten down the two clamp screws on the gearbox in the following sequence Tighten the first screw moderately Tighten the second screw moderately Tighten down first screw firmly Tighten down second screw firmly FS It must not be possible to rotate the gearbox on the drive tube 11 English Mounting the MultiTool e Arrange the blades in the order they will be fitted on the shaft noting the following points Left hand an
31. it is above shoulder level Good footing is very important Wear sturdy boots with nonslip soles Steel toed safety boots are recommended K For further instructions on proper clothing see the safety precautions in the instruction manual of the MultiEngine you are using THE POWER TOOL MULTIENGINE EQUIPPED WITH SOIL CULTIVATOR MULTITOOL For illustrations and definitions of the power tool parts see the chapter on Main Parts A Warning Never modify this power tool in any way Only attachments supplied by STIHL and expressly approved by STIHL for use with the specific STIHL power tool models are authorized Although certain unauthorized attachments are useable with STIHL power tools their use may in fact be extremely dangerous If this tool is subjected to unusually high loads for which it was not designed e g heavy impact or a fall always check that it is in good condition before continuing work Check in particular that the fuel system is tight no leaks and that the controls and safety devices are working properly Do not continue BF MM BK MM operating this machine if it is damaged In case of doubt have it checked by your STIHL servicing dealer THE USE OF THE POWER TOOL MULTIENGINE EQUIPPED WITH SOIL CULTIVATOR MULTITOOL Transporting the Power Tool A Warning To reduce the risk of injury from loss of control and MultiTool contact never carry or transport your power tool with the Mu
32. itions English Working in an alternating backwards and forwards motion is particularly suitable for loosening packed soil Working in a steady backwards or forwards motion is particularly suitable for working loose soil The rotor blades may only be mounted and operated in one position Arrows on the blades show the required direction of rotation see chapter on Mounting the MultiTool Typical Applications e Breaking up soil A few preparations are necessary before you begin to break up soil which has been previously tilled e g last year s vegetable or flower garden First clear away surface weeds and remains of other plants as well as hard objects like rocks stones bottles pieces of wood etc Hold the cultivator firmly with both hands and till only a small area at a time to the required depth Finish tilling the area by guiding the cultivator in such a way that you leave no footprints Use a rake to level off the entire area e Loosening soil around plants 10 z x o a e lt x d o O Only loosen the surface soil around plants Avoid going too deep as this could damage the shallow roots of some plants To avoid any damage to the cultivator or trees be wary not to catch the blades on the large roots of trees e Working in soil improvers The cultivator can be used for mulching with loam compost leaves other organic material or fertilizers Prepare the area by removing al
33. l old roots the remains of large plants and hard objects stones etc Spread the mulch evenly on the ground Work in the mulch with a back and forth motion Finish off by leveling the area with a rake e Trenching or furrowing Walk slowly backward and pull the cultivator to create the furrow required Repeat as necessary to obtain deeper furrows Cleaning the rotor blades Parts of plants e g roots can become tightly wrapped around or between the rotor blades during operation To clean the rotor blades Wear gloves Pull the hitch pins out of the axle Pull the rotor blades off the shaft Remove roots plants and soil Refer to Mounting the MultiTool for mounting instructions Cultivator spur special accessory The cultivator spur simplifies control and makes operation of the power tool less tiring It slows the forward motion and reduces the effort required to hold the power tool The spur breaks up the ridge between the rotor blades when tilling hard soil 2 x eo eo o X a o Y e Use the screw and knob to mount the cultivator spur to the right hand side of the flange e Setthe spur to the required depth and tighten it down firmly BF MM BK MM Approved MultiEngines Only use MultiEngines supplied by STIHL or expressly approved by STIHL for use with the MultiTool This MultiTool may only be used in combination with the STIHL MM 55 MultiEng
34. le el polvo en su fuente siempre que sea posible Utilice buenas pr cticas de trabajo tal como trabajar de manera que el viento o el proceso de corte dirija el polvo producido por la herramienta motorizada en sentido opuesto del operador Observe las recomendaciones emitidas por EPA OSHA NIOSH y las asociaciones de trabajo y los sindicatos con respecto al polvo materia particulada Cuando sea imposible eliminar significativa mente la inhalaci n del polvo es decir mantener el nivel cerca del valor ambiente el operador y las personas que se encuentren en la cercan a siem pre deber n usar un respirador aprobado por NIOSH MSHA para el tipo de polvo presente en el lugar 23 espa ol EE UU jPeligro Su herramienta motori zada no esta aislada contra las sacudidas el ctricas Para reducir el riesgo de sacudidas el c tricas compruebe que no haya cables el ctricos cerca de la superficie ni en la zona de trabajo que pudieran entrar en contacto con la Mul tiTool El cortar tales cables con la herramienta puede resultar en choques el ctricos y la posibilidad de lesiones graves o la muerte La informaci n acerca de la ubicaci n de cables el ctricos puede obtenerse de las empresas de servicio el ctrico locales o de un servicio de localizaci n de l neas el ctricas tal como Miss Utility o One Call Advertencia Utilice la herramienta motorizada nica mente a nivel del suelo El riesgo de l
35. ltiSystem Acerca de este manual de instrucciones Medidas de seguridad y t cnicas Motores MultiEngine aprobados Montaje de la MultiTool Arranque parada del motor Almacenamiento de la maquina Informacion para mantenimiento Componentes importantes Especificaciones Informaci n de reparaci n Marcas comerciales Manual de instrucciones original Las tintas contienen aceites vegetales el papel es reciclable Impreso en papel libre de cloro ANDREAS STIHL AG amp Co KG 2011 0458 484 8621 M2 C11 PM 0000000545 001 EA STIHL BF MM BK MM 18 18 19 26 28 28 29 30 30 31 32 32 33 espa ol EE UU Permita que solamente las personas que comprenden toda la informaci n contenida en los manuales del motor MultiEngine y de la cultivadora MultiTool manejen esta herramienta motorizada combinada Para obtener el rendimiento y satisfacci n m ximos de la herramienta MultiTool de STIHL es importante que lea obedezca y comprenda las precauciones de seguridad y las instrucciones de uso y mantenimiento dadas en el cap tulo Precauciones de seguridad y t cnicas de uso antes de usar la MultiTool Para obtener informaci n adicional visite www stihlusa com Comun quese con el concesionario o distribuidor de STIHL si no se entiende alguna de las instrucciones dadas en los dos manuales Advertencia Dado que el motor MultiEngine equi pado con una cultivadora MultiTool es una herramienta p
36. ltiTool moving A Warning Always switch off the engine and make sure the MultiTool has stopped before putting a power tool down 469BA001 KN Grip the power tool by the carrying handle with the attachment facing forward A Warning When transporting it in a vehicle prop erly secure it to prevent turnover fuel spillage and damage to the unit BF MM BK MM Before Starting A Warning Always check your power tool for proper condition and operation before starting Never attempt to modify the controls or safety devices A Warning Never operate your power tool if it is damaged improperly adjusted or main tained or not completely or securely assembled Unfold the bike handle into the working position and secure it with the knob see chapter Adjusting the bicycle handle of your MultiEngine instruction manual Keep the handles clean and dry at all times it is particularly important to keep them free of moisture pitch oil fuel mix grease or resin in order for you to maintain a firm grip and properly control your power tool A Warning To reduce the risk of injury from the MultiTool rotating in the wrong direction check that the position of the gearbox is correct and change it if necessary English On metal tools top illustration position the gearbox so that the shaft is below the drive tube Use for BF MM cultivator blades with pointed tines
37. nche 6 en el agujero del eje doble el pasador de enganche hasta que est plano contra la cuchilla Utilice el mismo procedimiento para colocar las cuchillas giratorias en el lado izquierdo espafiol EE UU Arranque parada del motor Arranque del motor Siempre siga el procedimiento de arranque descrito en el manual de instrucciones del motor MultiEngine z x e a o lt a o t e Fije el manillar en la posici n de trabajo normal e Retraiga las ruedas si las tiene consulte el cap tulo Ruedas en el manual de instrucciones de MultiEngine e Retraiga la espuela si la tiene e Coloque la m quina sobre el suelo Verifique que las cuchillas no est n tocando el suelo ni ning n otro obst culo La m quina deber quedar apoyada en la brida del motor y en el soporte de su bastidor e Aseg rese de tener los pies bien apoyados y de estar bien equilibrado tal como se ilustra 29 espa ol EE UU Para reducir el riesgo de sufrir lesiones debido al contacto con las cuchillas giratorias siempre p rese a un lado de la herramienta motorizada nunca delante de las cuchillas ni cerca de las mismas e Con la mano izquierda colocada en el mango t rico presiones la m quina firmemente contra el suelo no toque el gatillo de aceleraci n ni la palanca de bloqueo fo No se pare ni se arrodille sobre el manillar o el bastidor Las cuchillas pueden empezar a girar
38. nt parts for maintenance and repair Use of non STIHL parts may cause serious or fatal injury Wear gloves when handling or performing maintenance on blades A Warning Never repair damaged attachments by welding straightening or modifying the shape This may cause parts of the attachment to come off and result in serious or fatal injuries Tighten all nuts bolts and screws except the carburetor adjustment screws after each use BF MM BK MM Do not clean your machine with a pressure washer The solid jet of water may damage parts of the machine Store the power tool in a dry and high or locked location out of reach of children BF MM BK MM Using the Unit General Cultivator MultiTools are available in versions with pick tines BF MM and bolo tines BK MM Pick tines z 2 lt ra o e Pick tines are particularly suitable for tilling and loosening hard or packed soil English Bolo tines 469BA018 KN Not available in all markets Bolo tines are particularly suitable for working cultivated lighter soils Preparations Secure the handlebar in the normal operating position e Start the engine Working Technique 469BA016 KN The MultiEngine with rotor blades can be operated forwards 1 or backwards 2 Choose the method and type of rotor blade to suit your purpose i e this depends on the shape and size of the area and soil cond
39. oderosa es necesa rio tomar medidas especiales de seguridad para reducir el riesgo de lesiones personales El uso descuidado o inadecuado puede causar lesiones graves e incluso mortales 17 espa ol EE UU Sistema MultiSystem zZ eo a lt co D El sistema MultiSystem de STIHL permite combinar diversos motores MultiEngine y accesorios MultiTool para formar una maquina En el presente Manual de instrucciones la unidad funcional compuesta por el motor MultiEngine y el accesorio MultiTool se denomina la maquina De modo correspondiente los manuales de instrucciones del motor MultiEngine y del accesorio MultiTool constituyen el Manual de instrucciones completo de la maquina Siempre lea ambos manuales detenidamente antes de utilizar la maquina por primera vez y cons rvelos en un lugar seguro para consultarlos en el futuro 18 Acerca de este manual de instrucciones Pictogramas Todos los pictogramas que se encuentran fijados o grabados en la maquina se muestran y explican en este manual Simbolos en el texto Muchas de las instrucciones de uso y seguridad vienen acompa adas de ilustraciones Los pasos individuales o procedimientos descritos en el manual pueden estar se alados en diferentes maneras e Se usa un punto para denotar un paso o procedimiento Una descripci n de un paso o procedimiento que se refiere directamente a una ilustraci n puede contener n meros de ref
40. odically Careless or improper use may cause serious or fatal injury Have your STIHL dealer show you how to operate your power tool Observe all applicable local safety regulations standards and ordinances A Warning Do not lend or rent your power tool with out the instruction manuals of your MultiEngine and MultiTool Be sure that anyone using it understands the infor mation contained in these manuals BF MM BK MM A Warning The use of this machine may be hazard ous If a rotating blade comes in contact with your body it will injure you When it comes in contact with solid foreign objects such as rocks or bits of metal it may fling them directly or by ricochet in the direction of bystanders or the opera tor Striking such objects could damage the MultiTool and may cause blades to crack chip or break Thrown objects including broken blades may result in serious or fatal injury to the operator or bystanders STIHL does not recommend the use of non elastic blades in stony areas Use your MultiEngine equipped with the Soil cultivator MultiTool only for rejuvenation of flower beds and plantings and for mixing soil improving additives into the soil A Warning Do not use it for other purposes since misuse may result in personal injury or property damage including damage to the machine A Warning Minors should never be allowed to use this power tool Bystanders especially children and animals sho
41. omienda usar tambi n una careta o protector facial adecuado sobre las gafas o anteojos de seguridad El ruido de la herramienta motorizada puede da ar los o dos Siempre use amortiguadores del ruido tapones u orejeras para protegerse los o dos Los usuarios constantes y regulares deben Someterse con frecuencia a un examen o control auditivo Est especialmente alerta y tenga cuidado cuando se usa protectores de o dos ya que los mismos reducen la posibilidad de o r se ales de advertencia gritos alarmas etc Siempre use guantes cuando manipule la herramienta motorizada y sus accesorios Los guantes gruesos y anti deslizantes mejoran el manejo y ayudan a prote ger las manos La ropa debe ser de con fecci n fuerte y ajustada pero no tanto que impida la completa libertad de movimiento Use pantalo nes largos hechos de un material grueso para pro tegerse las piernas No use pantalones cortos sandalias o pies descalzos Evite el uso de chaquetas sueltas bufandas corbatas joyas pantalones acampanados o con vueltas pelo largo suelto o cualquier cosa que pueda engancharse en las ramas matorrales o piezas en movimiento de la m quina Suj tese el pelo de modo que quede sobre los hombros Es muy importante tener una buena superficie de apoyo para los pies P n gase botas gruesas con suela antideslizante Recomendamos las botas de seguridad con puntera de acero A Para instrucciones
42. os matorrales y el mate rial cortado Sea sumamente precavido cuando trabaje en declives o terreno irregular Camine a un paso normal mientras se use la herramienta motorizada Advertencia Para evitar el riesgo del contacto con el accesorio giratorio tenga sumo cuidado al tirar de la herramienta motorizada hacia s mismo Sea precavido al cambiar el sentido de trabajo de la herramienta motorizada especialmente en pendientes Advertencia Para evitar el riesgo de lesionarse por la p rdida del control nunca trabaje en pendientes empinadas Condiciones de trabajo Arranque y maneje su herramienta motorizada solamente al aire libre en un lugar bien ventilado Man jela solamente en condiciones de buena visibilidad y a la luz del d a Trabaje con mucho cuidado espa ol EE UU Advertencia Si el suelo que se est cultivando o la tierra en el lugar est recubierta de una sustancia qu mica tal como un pesti cida o herbicida activo lea y siga las instrucciones suministradas con la sus tancia en cuesti n Advertencia La inhalaci n de ciertos polvos especialmente los polvos org nicos tales como el moho o polen puede provocar reacciones al rgicas o asm ticas en las personas sensibles La inhalaci n repetida o de grandes cantidades de polvo u otros contami nantes del aire especialmente los de part culas pequefias puede causar enfermedades respiratorias o de otro tipo Contro
43. r tool never in front of or near the blades e With your left hand on the loop handle press the unit firmly against the ground do not touch the throttle trigger or lockout lever Fo Do not stand or kneel on the handlebar or frame The blades may begin to rotate as soon as the engine starts For this reason blip the throttle after starting the engine returns to idling speed Now follow the starting procedure described in the MultiEngine instruction manual To shut down the engine See MultiEngine instruction manual BF MM BK MM Storing the Machine For periods of 3 months or longer e Remove clean and inspect the rotor blades Store the machine in a dry high or locked location out of the reach of children and other unauthorized persons BF MM BK MM English Maintenance and Care The following intervals apply to normal operating conditions only If your daily working time is longer or operating conditions are difficult very dusty work area etc shorten the specified intervals accordingly All accessible screws and nuts e Retighten if necessary Sweeping attachments and deflectors e Visual inspection check tightness before starting work and after every refueling stop e Replace if damaged Safety labels e Replace illegible safety labels 13 English Main Parts 14 484BA001 KN a khwN Outer Right Hand Cultivator Blade Inner Right Hand Cultivator Blad
44. spuela rompe el entresurco formado entre las cuchillas giratorias cuando se labran suelos duros Z x eo eo eo X a o Y e Utilice el tornillo y perilla para montar la espuela cultivadora a la derecha de la brida e Ajuste la espuela a la profundidad deseada y apri tela bien firme 27 espa ol EE UU Motores MultiEngine aprobados Utilice Unicamente los motores KombiEngine provistos por STIHL o expresamente aprobados por STIHL para uso con la MultiTool Esta herramienta MultiTool puede usarse nicamente con el motor STIHL MM 55 MultiEngine 28 Montaje de la MultiTool Retiro de los accesorios MultiTool instalados Use guantes para reducir el riesgo de lesiones causadas por el contacto con las MultiTool afiladas y o la superficie caliente de la caja de engranajes z eo e e lt ao Saque el pasador de enganche y quite las MultiTool si las tiene del eje consulte Montaje de la MultiTool en el manual de instrucciones de la otra MultiTool e De ser necesario limpie la caja de engranajes Revisi n de la posici n de la caja de engranajes Para reducir el riesgo de lesiones causadas por el giro de la MultiTool en el sentido incorrecto revise la posici n de la caja de engranajes y aj stela seg n se requiera 2 eL X o pa ES O X O 1 WA 5 3 3 lt Eje de salida 1 de caja de engranajes debajo del tubo de mando
45. the STIHL part number the STIHL logo and in some cases by the STIHL parts symbol amp 7 The symbol may appear alone on small parts English Trademarks STIHL Registered Trademarks STIHL STIHL 5 The color combination orange grey U S Registrations 2 821 860 3 010 057 3 010 058 3 400 477 and 3 400 476 e 4 MIX AUTOCUT EASYSTART FARM BOSS iCademy9 OILOMATIC STIHL Cutquik STIHL DUROMATIC STIHL Quickstop STIHL ROLLOMATIC STIHL WOOD BOSS TIMBERSPORTS WOOD Boss YARD BOSS 15 English Some of STIHL s Common Law Trademarks T TIHL BioPlus Easy2Start EasySpool ElastoStart Ematic FixCut HT Plus IntelliCarb TM Master Control Lever Micro TM Pro Mark Quad Power Quiet Line STIHL Compact STIHL HomeScaper Series STIHL Interchangeable Attachment Series STIHL M Tronic STIHL Magnum STIHL MiniBoss STIHL MotoPlus 4 STIHL Multi Cut HomeScaper Series STIHL OUTFITTERS STIHL PICCO STIHL PolyCut STIHL PowerSweep 16 STIHL Precision Series STIHL Protech STIHL RAPID STIHL SuperCut STIHL Territory TapAction TrimCut This listing of trademarks is subject to change Any unauthorized use of these trademarks without the express written consent of ANDREAS STIHL AG amp Co KG Waiblingen is strictly prohibited BF MM BK MM Contenido Sistema Mu
46. tos s lidos Estos objetos pueden salir lanzados por la herramienta direc tamente o por rebote hacia personas que se encuentren en la cercan a o hacia el operador Estos objetos tam bi n pueden da ar la MultiTool La cuchilla puede astillarse o romperse Los objetos lanzados o las cuchillas dafiadas pueden causar lesiones gra ves o la muerte del operador o de las personas en la cercan a Advertencia Nunca desv e la descarga del material hacia otras personas ni permita que persona alguna se acerque a la zona de trabajo Tenga sumo cuidado al dirigir la descarga del material para evitar da ar las superficies los autom viles y obje tos similares Advertencia Evite cortar cerca de vallas edificios tocones piedras u otros objetos de ese tipo que puedan da ar la cuchilla o resultar en la p rdida de control de la unidad Est alerta a la posibilidad de rebote de los objetos lanzados en estas condiciones Los objetos lanzados o las cuchillas da adas pueden causar lesio nes graves o la muerte del operador o de las personas en la cercan a Evite las ra ces de los rboles Las ra ces grandes pueden aprisionar las cuchillas y da ar la m quina Tambi n es posible da ar el rbol al cortar las ra ces BF MM BK MM Si la maquina choca contra un objeto enterrado tal como una piedra apague el motor y quite el obst culo Examine la m quina en busca de se ales de da os antes de proceder Advert
47. uld damage the blade or lead to loss of control of the unit Be aware of a higher risk of rico chets in such conditions Flying objects or damaged blades may cause serious or fatal injuries to the operator and bystanders Avoid the roots of trees Large roots may jam the blades and damage the machine The tree may also be damaged if its roots are severed If the machine strikes a buried object such as a stone stop the engine and remove the obstacle Examine the machine for signs of damage before continuing A Warning Check the tightness and condition of the MultiTool at regular intervals during cut ting If the behaviour of the tool changes stop the engine immediately and examine the tool Replace a cracked bent warped or damaged blade immediately even if damage is limited to superficial cracks Such attachments may shatter at high speed and cause serious or fatal injury A Warning The gearbox becomes hot during oper ation To reduce the risk of burn injury do not touch the gear housing when it is hot MAINTENANCE REPAIR AND STORING A Warning Always stop the engine and make sure that the attachment is stopped before doing any maintenance or repair work or cleaning the power tool Do not attempt any maintenance or repair work not described in your MultiEngine and MultiTool instruction manuals Have such work performed at your STIHL servicing dealer only A Warning Use only identical STIHL replaceme
48. uld not be allowed in the area where it is in use English A Warning To reduce the risk of injury to bystand ers and damage to property never let your power tool run unattended When it is not in use e g during a work break shut it off and make sure that unauthor ized persons do not use it Most of these safety precautions and warnings apply to the use of all STIHL power tools Different models may have different parts and controls See the appropriate section of your MultiEngine and MultiTool instruction manuals for a description of the controls and the function of the parts of your model Safe use of a power tool involves 1 the operator 2 the power tool 3 the use of the power tool THE OPERATOR Physical Condition You must be in good physical condition and mental health and not under the influence of any substance drugs alcohol etc which might impair vision dexterity or judgment Do not operate this machine when you are fatigued English A Warning Be alert if you get tired take a break Tiredness may result in loss of control Working with any power tool can be strenuous If you have any condition that might be aggravated by strenuous work check with your doctor before operating this machine Proper Clothing A Warning To reduce the risk of injury the operator should wear proper protective apparel The suitable deflector for your power tool will not protect the operator from
49. y respete las siguientes advertencias y medidas de seguridad Lea peri dicamente los manuales de instrucciones y las precauciones de seguri dad de su motor MultiEngine y accesorio MultiTool El uso descui dado o inadecuado puede causar lesiones graves o incluso mortales Pida a su concesionario STIHL que le ensefie el manejo de la herramienta motorizada Respete todas las disposiciones reglamentos y normas de seguridad locales del caso BF MM BK MM Advertencia No preste ni alquile nunca su herra mienta motorizada sin entregar los manuales de instrucciones de su motor MultiEngine y la MultiTool Aseg rese que todas las personas que utilicen la m quina lean y comprendan la informa ci n contenida en estos manuales Advertencia El uso de esta m quina puede ser peli groso Si la cuchilla giratoria llega a entrar en contacto con su cuerpo le ocasionar una lesi n Cuando choca con alg n objeto extra o s lido tal como rocas o pedazos de metal puede arro jarlo directamente o por rebote en direcci n de personas que se encuen tren en la cercan a o del operador El contacto con dichos objetos puede da ar la herramienta MultiTool y puede hacer que las cuchillas se rompan asti llen o agrieten Los objetos lanzados incluso las cuchillas rotas pueden pro vocar lesiones graves o mortales al Operador o a personas que se encuen tren en su proximidad STIHL no recomienda el uso de cuchillas r gid
Download Pdf Manuals
Related Search
Related Contents
Slant/Fin Sentry S-120 User's Manual AP-55 Disc Printer Loader System User Manual Rev USER MANUAL - Edinburgh Projector Sales FIS VS 300T FOAM-U12SW・U12SC取扱説明書【PDF208KB】 ーNAX Alcatel-Lucent 4610 IV Answering Machine User Manual AOC T2442e User's Manual User's Guide for the Polycom Mobile Responder Copyright © All rights reserved.
Failed to retrieve file