Home

Manual MX-2

image

Contents

1. A daal 0 MTT TIT STEREO MIXER ix e2 MANUAL DE INSTRUCCIONES INSTRUCTIONS MANUAL NORMAS PARA SU SEGURIDAD akiyama WARNING espa ol PARA EVITAR ACCIDENTES PROVOCADOS POR EL FUEGO O LA ELECTROCUTACION EN CASO DE QUE LOS PIN DE LA CLAVIJA NO ENTREN COMPLETAMENTE EN SU POSICION NO UTILICE LA CLAVIJA DE CONEXION CON UN CABLE EXTENSOR UN ADAPTADOR O CUALQUIER OTRO INTERFACE QUE DEJE PARTE DEL PIN EXPUESTO PARA EVITAR ACCIDENTES PROVOCADOS POR EL FUEGO O LA ELECTROCUTACION NO EXPONGA EL CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Esta se al indica la presencia de lugares donde habiendo un elevado voltaje no presentan aislamiento y por tanto constituye un claro riesgo de electrocuci n 1 Lea detenidamente este manual antes de utilizar su equipo 2 Mantenga el manual a su disposici n para su uso en el futuro 3 Siga las advertencias que se le proporcionan en este manual 4 Siga las instrucciones consignadas en este manual un uso indebido podr a dejar sin efecto la garant a 5 Agua y humedad No utilice el equipo cerca del agua o en lugares muy h medos fregadero lavadora etc para evitar riesgos de descarga el ctrica o fuego 6 Transporte del equipo Transporte el equipo con mucho cuidado Los golpes o las vibraciones fuertes pueden da arlo mec nicamente 7 Montaje en pared o techo Siga las instrucciones del fabricante 8 Fuentes de calor Tenga cuidado de no colocar
2. escuchar una mezcla entre las se ales entrantes del canal 1 y 2 Escuchamos una mezcla est reo de ambas se ales en funci n del sentido en que giremos el bot n 8 9 Nivel de volumen de auriculares Le permite controlar el volumen en un auricular est reo conectado al mezclador Por favor aseg rese de que la impedancia del auricular sea como m nimo de 32 Ohmios Adem s est prevenido contra auriculares de elevada impedancia que reducir n el nivel m ximo de salida en auricular Se recomienda escoger un auricular con una impedancia no superior a 200 Ohmios Atenci n se recomienda mantener el volumen al m nimo antes de comenzar la reproducci n 10 Fader de Master Determina el nivel total de se al de salida del mezclador MX 2 akiyama 11 Ganancia de canal Permite el ajuste de la sensibilidad del canal de entrada en funci n de las distintas fuentes Para cada canal es posible realizar un ajuste ptico mediante la barra de LED o pic metro Atenci n Tenga siempre la precauci n de enchufar primero el mezclador y a continuaci n el amplificador para evitar que el ruido de conexi n da e sus altavoces para apagar el equipo apague primero el amplificador y a continuaci n el mezclador MX 2 Panel trasero RISK OF ELECTRIC SHOCK F DO NOT OPEN J AKIYAMA 08191 BARCELONA SPAN DONOTOPEN Power J n Dif 12 13 14 12 Conector de puesta en marcha Accio
3. CONECTORES DEL MEZCLADOR A CAUTION RISK OF ELECTRIC SHOCK 17 18 siguiente I Disponga el control fader del canal al que est conectado el reproductor de CD en la posici n 0 II Busque el punto de arranque deseado en el reproductor de CD y disponga ste en posici n Pausa en este punto suele llamarse CUE point IHI Para comenzar la reproducci n del CD eleve la posici n del fader y el CD comenzar la reproducci n en el punto CUE seleccionado con anterioridad En el caso del giradiscos una vez debidamente conectado Al elevar la posici n del fader correspondiente comenzar la reproducci n 15 Salida Master L R Conecte al amplificador Normalmente usamos esta salida para conectar a amplificadores dom sticos o amplificadores profesionales 16 Entradas de L nea Inserte aqu los conectores RCA de cualquier fuente de se al de l nea CD Player MD player Cassette Player etc 17 Entradas Phono giradiscos Inserte aqu los conectores RCA de los giradiscos tipo MM moving magnet En la actualidad todos los giradiscos para DJ son del tipo MM 18 Toma de tierra Los giradiscos disponen de un cable auxiliar de masa o tierra Conecte este cable a la toma de tierra del mezclador de este modo anulamos los posibles ruidos de masa o tierra hum jouedsa espa ol CARACTER STICAS Y ESPECIFICACIONES akiyama Caracter sticas A P Dise o compacto P Crossfader reemplazable P Entrada
4. cassette and reel to reel tape decks DAT machines laser discs tuners even synthesizers or other mixing consoles 17 Phono Inputs Plug your turntables in here When these connectors are used your signal is fed directly to the high quality RIAA phono pre amplifiers Use this position only for turntables Line level sources will overload the sensitive phono pre amps and will cause distortion 18 Grounding lug for turntable connection Always use this connection when using standard turntables with ground cable acer Ne e me MX 2 FEATURES AND SPECIFICATIONS akiyama gt Compact design P User replaceable crossfader 2 phono 2 line 1 microphone input P Powerful stereo headphone output P Cue Pan Selector Ch 1 Ch 2 gt Bright LED Output Indicators L Gain Treble and Bass Controls on Channels P Selectable Fader Start Ch 1 CH 2 Fe T Specifications SENSITIVITY OF INPUT LEVEL IMPEDANCE LINE 14dB 47K OHM 3dB PHONO 50dB 47K OHM 3dB MIC 54dB 6K OHM 3dB OUTPUT LEVEL IMPEDANCE MASTER RCA 0dB 47K OHM 3dB PHONES LOAD 32 OHM 3dB 33 OHM 3dB MAX OUTPUT LOAD 47K THD 5 MASTER RCA MORE THAN 18dB 8V PHONES LOAD 32 OHM MORE THAN 5dB 1 8V CHANNEL BALANCE WITHIN 3dB FREQUENCY RESPONSE LINE 20 20KHz 3dB PHONO 20 20KHz 2 3dB RIAA MIC 50 20KHz 2 3dB OUTPUT NOISE IEC A WEIGHTED LINE LESS THAN 75dB PHONO LESS THAN 65dB MIC LESS THAN 55dB TOTAL HARMONIC DISTO
5. other This plug will fit into the bracket or table recommended by the manufacturer or power outlet only one way This is a safety feature If you sold with the product Any mounting of the product should a unable to insert the plug fully into the outlet try follow the manufacturer s instructions and should use a reversing the plug If the plug should still fail to fit contact mounting accessory recommended by the manufacturer your electrician to replace your obsolete outlet Do not 20 Lightning For added protection for this product during a defeat the safety aan ae of the polarized plug lightning storm or when it is left unattended and unused 11 Power Cord Protection Power supply cords should be for long periods of time unplug it from the wall outlet and routed so that they are not likely to be walked on or pinched disconnect the antenna or cable system This will prevent by items placed upon or against them paying particular damage to the product due to lightning and power line attention to the cord in correspondence of plugs surges convenience receptacles and the point where they exit 22 Replacement Parts When replacement parts are 12 ea O i abad onl required be sure the service technician has used ESTO Pp o an A ede Aen replacement parts specified by the manufacturer or have recommended by the manufacturer Clean by wiping with A the same characteristics as the original part Unauthorized cloth slightly damp with water Avoid getting wa
6. HIS PLUG WITH AN EXTENON CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PRESENT BLADE EXPOSURE TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE TO PRVENT ELECTRICAL SHOCK MATCH WIDE BLADE PLUG TO WIDE SLOT FULLY INSERT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION To reduce the risk of electric shock do not remove any cover No user serviceable parts inside Refer servicing to qualified service personnel only The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use to the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operation and maintenance servicing instructions in the literature accompanying this appliance constitute a risk of electric shock Read Instructions All the safety and operating instructions should be read before this product is operated blades to all exposed metallic parts The resistance should be more than 100 000 ohms 2 Retain Instructions The safety and operating instructions 14 Non use Periods The power cord of the appliance should should be retained for future reference be unplugged from the outlet when left unused for a long 3 Heed Warnings All warnings on the appliance and in the period of ti
7. L EQUIPO PONGASE EN CONTACTO CON ELPERSONAL CUALIFICADO Esta se al indica la presencia de componentes del equipo que precisan de mantenimiento Para m s informaci n sobre stos lea el manual 15 Da os en el quipo que precisen reparaci n El equipo deber ser reparado o revisado por personal cualificado en caso de A El cable de toma de corriente o su conector han sido da ados B Objetos o l quidos se han introducido en el equipo C El aparato ha sido expuesto a la lluvia D El equipo no parece funcionar o lo hace de modo poco usual E El aparato ha ca do al suelo o presenta deterioros en su caja exterior 16 Mantenimiento No abra el equipo para labores de mantenimiento pues en este aparato no hay piezas que necesiten manutencion En caso de que abriendo el equipo sea ste da ado o lo sea la persona que lo manipula la empresa no tomar ninguna responsabilidad por este servicio de mantenimiento no autorizado Adem s en ste caso la garant a perder a su vigencia 17 Ventilaci n El aparato est provisto de hendiduras de ventilaci n es importante no cubrirlas o bloquearlas La ventilaci n del aparato podr a verse comprometida resultando en un sobrecalentamiento que podr a da ar el equipo Tenga siempre en cuenta que colocar el aparato en un lugar sin ventilaci n puede producir un sobrecalentamiento de ste 18 Nunca utilice accesorios o modificaciones no autorizados por el fabricante Ello puede afec
8. RTION MASTER OUTPUT LOAD 47K OHM LESS THAN 0 2 PHONES OUT LOAD 32 OHM LESS THAN 0 3 CROSSTALK MORE THAN 50dB AT 1KHz BETWEEN LAND R CHANNEL EQUALIZER LOW 9 26dB 2 3dB AT 100Hz HI 9 26dB 2 3dB AT 10KHz MIC EQ LOW 10 10dB 2 3dB AT 100Hz HI 10 10dB 2 3dBAT 10KHz POWER SOURCE AC9V DIMENSIONS 228 W X 265 D X 87 H mm WEIGHT 2 8Kgs 9 mx 2 mx 2 CONEXIONES CONNECTIONS FW CAUTION e a RISK OF ELECTRIC SHOCK re CAUTION RISK OF ELECTRIC SHOCK o DONOTOPEN UN STIX O de Turntables earth connection 9 e o 9 e o Toma de tierra para On pl L giradiscos O Q EAS g powersuppiy E ne phono A ine pront A ch AX pa N R L POWER AMPLIFIER ETAPA DE POTENCIA TURNTABLE GIRADISCOS Up to 2 turntables can be connected Podemos conectar hasta 2 giradiscos CD PLAYER 1 L R CD PLAYER 2 L R CD PLAYER REPRODUCTOR DE CD w El so Ee gt i poa gt i pn p mr x ORCI A Up to 2 line level devices can be connected Podemos conectar hasta 2 aparatos de nivel de se al de l nea MX 2 10 ys bu3 jouedsa C Praga n 11 P Cova Solera 08191 Rubi Espa a Tel 0034935861730 Fax 0034936996087 info akiyamadj com www akiyamadj com
9. el equipo cerca de fuentes de calor Ej Radiadores estufas amplificadores etc 9 Voltaje Antes de conectar el aparato a la red aseg rese de que se trata del mismo voltaje y frecuencia para las que el equipo est especificado En caso contrario no conecte el equipo y p ngase en contacto con su distribuidor 10 Protecci n del cable Escoja una posici n para el cable de corriente de modo que est lo menos expuesto a pisotones y dem s agresiones Especial atenci n con los dos extremos del cable de toma de corriente la clavija de enchufe a la red y la clavija de alimentaci n del equipo 11 Limpieza Desconecte el equipo antes de realizar alguna operaci n de limpieza del aparato Utilice un trapo suave y seco para limpiar Aseg rese de que los cables est n correctamente conectados antes de volver a enchufar el aparato 12 Control de seguridad La diferencia de potencial entre la toma de corriente de la pared y cualquier pieza met lica del equipo debe ser de al menos 100 000 ohmios 13 Periodos largos de reposo del equipo Desconecte el equipo de la red en caso de reposo prolongado 14 L quidos y objetos extra os En caso de que alg n fluido o peque as part culas s lidas sean derramadas sobre el aparato y se introduzcan en los circuitos apague el aparato y ll velo a su distribuidor MX 2 ATENCION PARA REDUCIR EL RIESGO DE ELECTROCUCION NO MANIPULE EL INTERIOR DEL EQUIPO PARA REALIZAR EL MANTENIMIENTO DE
10. entar el nivel total y har decrecer el rango din mico del equipo Adem s puede elevar el nivel global de la se al hasta llegar a la saturaci n 3 Fader de canal Mediante estos controles usted determina la parte del nivel global al que un canal espec fico contribuye Por favor advierta que el nivel final de salida debe ser ajustado mediante el Master Adem s el nivel de los canales puede depender de la posici n del Crossfader 4 CrossFader Dada la condici n de los Fader de los canales que est n abiertos se podr combinar la se al de stos acci n de Crossfader o fundido Para mayor operatividad y agilidad del equipo el componente mec nico donde se localiza la funci n de Crossfader es reemplazable Para reemplazar el Crossfader desaloje los tornillos exteriores y retire la pieza desconecte el conector y cambie la pieza De la nueva pieza conecte el conector y atorn llela al equipo 5 Conector de Micr fono Conecte aqu su micr fono mediante un conector Jack de 1 4 de pulgada 6 Conector de auriculares Conecte aqu sus auriculares mediante un conector Jack de 1 4 de pulgada 7 Selector de entradas Mediante la palanca de cada canal decidimos que fuente reproductora est activa de las dos posibles conectadas a cada canal Se dispone de 2 posibles selecciones Phono giradiscos con c psula MM L nea CD y L nea son el mismo tipo de entrada 8 Preescucha Panor mica Mediante esta funci n podr
11. er Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating and these 8 Heat The appliance should be situated away from heat openings must not be blocked or covered The openings hats such En radiators heat registers stoves or other should never be blocked by placing the product on a bed appliances including amplifiers that produce heat sofa rug or other similar surface This product should not 9 Power Sources This product should be operated only be placed in a built in installation such as a bookcase or from the type of power source indicated on the rating rack unless proper ventilation is the manufacturer s label If you are not sure of the type of power supply to netiuetions have besmadhered o your home consult your p roduct dealer or local power 19 Attachments do not use attachments not recommended company For products intended to operate fr li by the product manufacturer as they may cause hazards patel pOr other sources refer the operating 20 Accessories Do not place this product on an unstable cart SUUE HONS ae l stand tripod bracket or table The product may fall 10 Grounding or Polarization This product may be equipped causing serious injury to a child or adult and serious with a polarized alternation current line plug a plug having damage to the product Use only with a cart stand tripod one blade wider than the
12. ere 7 Input toggle switch Selects which source will be 4 active based on what you have connected to the rear panel input section phono line 6 8 Channel Cue Cue Pan Used to preview channel i audio to your headphones Listen here before bringing 5 ee up channel faders or moving the crossfader E 9 Headphone Level Adjusts cue volume 10 Master Fader Controls the overall output level 11 Channel Gain Adjusts the pre fader volume for cleaner sound tader sate f Rear Panel 12 Power Switch turns unit offand on A JBL DL 13 Power Connector Plug in power adapter Sm j ma CAUTION here and check the voltage level to match your lariyama VN pi 9 AKIYAMA lA SPAN CAUTION RISK OF ELECTRIC country S standard l SHOCK D HD Toes on 14 Fader Start This function works in conjunction with a compatible fader start CD player When used with a compatible CD player you can use the crossfader to start and stop the CD player with the slide of the fader The fader start switch activates the fader start feature When in the ON position the fader start allows the fader to return automatically to preset digital CUE POINTS on your 12 13 14 15 16 17 18 compatible CD Player 15 Stereo Main Outputs Unbalanced RCA connectors controlled by the Master fader 16 Line Inputs Unbalanced RCA jacks for connecting stereo audio from line level sources such as CD players HiFi VCRs
13. me operating instructions should be adhered to 15 Object and Liquid Entry Care should be taken so that 4 Follow Instructions All operating and use instructions objects do not fall and liquids are not spilled into the should be followed enclosure through openings 5 Water and Moisture The appliance should not be used 16 Damage Requiring Service The appliance should be near water for example near a bathtub washbowl serviced by qualified service personnel when kitchen sink laundry tub in a wet basement or near a gt The power supply cord or the plug has been damaged or swimming pool and the like gt Objects have fallen or liquid has been spilled into the 6 Carts and Stands The appliance should be used only appliance or with a cart or stand that is recommended by the gt The appliance has been exposed to rain or manufacturer o gt The appliance does not appear to operate normally or An appliance and cart combination should be moved exhibits a marked change in performance or A ee ECR S10pS EOS force ane ee gt The appliance has been dropped or the enclosure surfaces may cause the appliance and cart combination to damaged Overtunn 17 Servicing The user should not attempt any service to the appliance beyond that described in the operating AA instructions All other servicing should be referred to 7 Wall or Ceiling Mounting The product should be 18 o O recommended by mounted to a wall or ceiling only as the manufactur
14. nando el conmutador Power Switch el aparato ser puesto en marcha Mediante una segunda acci n sobre el conmutador el aparato se apagar El LED correspondiente se iluminar cuando el aparato est en funcionamiento Por favor advierta que este LED no se apagar inmediatamente al desconectar el equipo debido a que el condensador debe de descargarse antes Atenci n Tenga siempre la precauci n de enchufar primero el mezclador y a continuaci n el amplificador para evitar que el ruido de conexi n da e sus altavoces para apagar el equipo apague primero el amplificador y acontinuaci n el mezclador 13 Z calo de conexi n a red Conectar el dispositivo de conexi n a red AC a la toma de la pared Accionando el conmutador Power Switch el aparato ser puesto en marcha 14 Arranque remoto por fader Los canales est n dotados de funci n de arranque de un equipo remoto mediante el fader del canal al que est conectado dicho equipo Las conexiones son tipo Jack 3 5 Esta funci n nos permite el arranque remoto de un reproductor de CD o Giradiscos conectado al mezclador Para habilitar el arranque remoto mediante fader potenci metro deslizante deberemos conectar el reproductor de CD o Giradiscos auno de los conectores 14 Una ver realizada esta conexi n el proceso de arranque remoto de un reproductor de CD es el NOTA En la p gina final de este manual se presenta un diagrama de conexiones TION 15 16 MX 2
15. pero al realizarla debemos tener en cuenta principalmente dos cosas nivel de la se al dentro del mezclador y saturaci n de la se al El control GAIN sirve para ajustar el nivel de la se al de entrada NO PARA AUMENTAR EL VOLUMEN Este es un punto muy importante Debes tener en cuenta que la amplificaci n de la se al es asunto del amplificador y de las cajas ac sticas no del mezclador S1 quieres m s volumen puedes Subir el fader de canal Subir el fader de Master Subir los controles de volumen del amplificador NUNCA intentes controlar el volumen con el control GAIN distintos equipos y en cada uno de ellos esta se al debe tener el nivel adecuado Si en cualquier equipo de la cadena electr nica saturamos la se al Esta saturaci n se prolongar a lo largo de la cadena hasta tus cajas ac sticas Y stas sonar n mal As pues tenemos claro que debemos evitar la saturaci n Para evitarla en el mezclador debemos observar que tanto el nivel de entrada despu s de GAIN como el de salida Master no mantienen en rojo de un modo continuo los LEDs de medida de nivel jouedsa espa ol CONTROLES DEL MEZCLADOR Panel frontal 1 Control de ganancia de micr fono Permite el ajuste de la sensibilidad de la se al de entrada del micr fono 2 Ecualizador Se dispone de un control independiente para frecuencias altas medidas y bajas Por favor advierta que cualquier banda de frecuencia sobreelevada increm
16. s 2 phono 2 l nea 1 micr fono gt Control Gain Treble y Bass en canales gt Salida de cascos potente P Selector Cue Pan Ch 1 Ch 2 gt Indicadores Led de nivel gt Fader Start seleccionable CH 1 CH 2 Especificaciones _a_ _ ________ __ _ _ SENSIBILIDAD DE ENTRADA NIVEL IMPEDANCIA L NEA PHONO MIC SALIDA NIVEL IMPEDANCIA MASTER RCA PHONES CARGA 32 OHM SALIDA M XIMA CARGA 47K THD 5 MASTER RCA PHONES CARGA 32 OHM BALANCE ENTRE CANALES RESPUESTA EN FRECUENCIA L NEA PHONO MIC RUIDO EN SALIDA IEC A WEIGHTED L NEA PHONO MIC DISTORSI N HARM NICA MASTER OUTPUT LOAD 47K OHM PHONES OUT LOAD 32 OHM CROSSTALK Separaci n entre canales ENTRE CANALES L Y R ECUALIZADOR LOW HI 9 26dB 2 3dB A 10KHz MIC EQ LOW HI 10 10dB 2 3dB A 10KHz ALIMENTACI N DIMENSIONES 228 A X 265 Prof X 87 Al mm PESO 14dB 47K OHM 3dB 50dB 47K OHM 3dB 54dB 6K OHM 3dB 0dB 47K OHM 3dB 3dB 33 OHM 3dB MAS DE 18dB 8V MAS DE 5dB 1 8V ENTRE 3dB 20 20K Hz 3dB 20 20KHz 2 3dB RIAA 50 20KHz 2 3dB MENOS DE 75dB MENOS DE 65dB MENOS DE 55dB MENOS DE 0 2 MENOS DE 0 3 MAS DE 50dB A 1KHz 9 26dB 2 3dB A 100Hz 10 10dB 2 3dB A 100Hz AC 9V 2 8Kgs mx 2 ENGLISH MANUAL english WARNINGS akiyama WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT USE T
17. tar la seguridad del aparato y el fabricante no tomar ninguna responsabilidad en este caso 19 Accesorios No deposite o instale el equipo sobre superficies o estructuras inestables El aparato podr a precipitarse y causar lesiones a las personas en las proximidades de ste Cualquier montaje o instalaci n del equipo deber ser realizado siguiendo las instrucciones o recomendaciones dadas en este manual o por el fabricante directamente 20 Precauci n durante tormentas Durante una tormenta desconecte el equipo de la red para evitar que los posibles picos de corriente da en el equipo 21 Durante cualquier manipulaci n del equipo para mantener todas las cualidades de ste tanto en prestaciones como en seguridad para el operante es necesario utilizar s lo recambios originales Consecuentemente aseg rese de que la empresa que realice el mantenimiento est autorizada por el fabricante o importador 22 Comprobaci n de seguridad Una vez realizada una reparaci n o servicio del equipo pida al personal cualificado que realice una comprobaci n para asegurarse de que el equipo le es devuelto en perfectas condiciones de uso MX 2 10 minutos L eme Es posible que este sea tu primer mezclador es por ello que hemos cre do oportuna esta introducci n donde te Nomenclatura Este es el bot n que controla un potenci metro rotativo Lo llamaremos Potenci metro 3 Lj x gain Un mezclador es un equipo elec
18. ter inside substitutions may result in fire electric shock or other the appliance Basan 13 For AC line powered units Before returning repaired unit 23 l to user use an ohm meter to measure from both AC plug Safety Check Upon completion of any service or repairs to mx 2 MIXER CONTROLS Front Panel 1 Mic Input Gain Adjusts microphone input level 2 Treble and Bass EQ Adjusts the high and low _ a frequency levels ofthe input channels for good sound AYTA 3 Input fader Controls individual source levels Az j a Js AAA a E 4 gt Es max gain vis e channels in the mix San l D level a bag 4 Replaceable Crossfader Achieves clean segues 1 rr are T we E ha 7 A between the two input channels Hard left selects GUS 7 Channel 1 Hard right selects Channel 2 With the _ o Van g crossfader centered both assigned channels are live Use the crossfader for fast and seamless segues fades from one selected channel to the other Note The crossfader is user replaceable in case of failure Simply unscrew the two large screws which hold it in place lift it out and disconnect it s cable Re attach the new crossfader and screw the mounting plate back onto the unit you re back in business 5 Mic Input Insert your Microphone with 4 plug in hete 6 Headphone Input Insert in the 4 plug for your headphones h
19. tr nico que recibe se al de distintos reproductores la mezcla y env a su salida Master a la etapa de amplificaci n Esta es su funci n Nivel de la se al dentro del mezclador Cada mezclador tiene lo que se llama un nivel nominal Este es el nivel de se al al que el mezclador trabaja en ptimas condiciones evitando ruidos de base y evitando llegar a saturaci n sobre saturaci n en unos minutos El nivel de la se al de los distintos reproductores conectados al mezclador debe ser parejo El nivel de se al entrante se controla con el potenci metro GAIN Para ajustar el nivel de una se al entrante debemos observar la barra de LEDs mientras manipulamos el potenci metro GAIN tal que sta s lo se ilumina en rojo espor dicamente Saturaci n Que es la saturaci n Es el deterioro de una se al debido a que su nivel es tan elevado que el equipo no puede proporcionar voltaje suficiente para amplificarla sin deteriorarla Una se al saturada suena mal La se al el ctrica que sale de tu reproductor de CD pasar primero por el mezclador despu s posiblemente por un procesador de efectos a continuaci n por tu amplificador y finalmente por tus cajas ac sticas En este recorrido electr nico pasa por MX 2 prevendremos de los errores m s comunes que realiza la gente al utilizar un mezclador Este es el bot n que controla un potenci metro deslizante Lo llamaremos Fader

Download Pdf Manuals

image

Related Search

Related Contents

  

Copyright © All rights reserved.
Failed to retrieve file