INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES
Contents
1. INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Model Numbers No de Modelos W798SS 1 PORTABLE WASHER LAVADORA PORTATIL BEFORE USE PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS La secci n en espa ol empieza en la p gina 18 Avanti has a policy of continuous improvement on its products and reserves the right to change materials and specifications without notice Avanti Products A Division of the Mackle Co Inc P O Box 520604 Miami Florida 33152 www avantiproducts com TABLE OF CONTENTS Help Us Help You 3 Parts and Features 4 Important Safety Instructions 5 Installation Instructions 5 Before Using Your Appliance Selecting a Location Adjusting the Adjustable Foot Installing the Noise Proof Plate 5 s Connecting the Water Supply Water Connection Disconnecting the Water Inlet Hose Positioning the Drain Hose Electrical Connection 9 Control Panel 10 Operating Your Appliance Preparation Before Washing Operation Instructions Automatic Wash Programs 10 15 Manual Functions Functions Delay Start Instructions Children Proof Setting Care and Maintenance 15 Cleaning Your Appliance 15 Troubleshooting Guide 16 Service for Your Appliance 16 Wiring Diagram 16 Your Avanti Products Warranty 17 Instrucciones en Espa ol 18 26 Registration Information and Registration Card 27 HELP US HELP YOU Read this guide carefully It2. CONECTANDO LA MANGUERA DE SUMINISTRO DE AGUA UN EXTREMO DE LA MANGUERA PARA SUMINISTRO DE AGUA DEBE SER CONECTADO A LA LAVADORA Y EL OTRO EXTREMO AL GRIFO NO ESTIRE LA MANGUERA DE SUMINISTRO DE AGUA SI LA MANGUERA ES MUY CORTA Y NO DESEA MOVER EL GRIFO REEMPLACE LA MANGUERA CON UNA MAS LARGA DE ALTA PRESION SELECCIONE EL GRIFO ADECUADO TAL COMO SE MUESTRA EN LAS FIGURAS ABAJO SI NINGUNO DE ESTOS GRIFOS ESTA DISPONIBLE USE EL ADAPTADOR INCLUIDO EL LARGO DEL GRIFO DEBE SER DE MAS DE 10 MM 0 4 DE OTRA MANERA EL CONECTOR NO PODRA SER AJUSTADO APROPIADAMENTE Y PODRIA PRODUCIR GOTEO IMPORTANTE EN ESTA SITUACION NO PROGRAME LA OPCION CALIENTE HOT COMO TEMPERATURA DE LAVADO 1 CONECTE LA MANGUERA AL GRIFO DE 2 REMUEVA LA TAPA DEL CONECTOR DE SUMINISTRO DE AGUA A LALLAVE AGUA FRIA Y CONECTE EL OTRO GIRANDO LA TUERCA DEL CONECTOR EXTREMO DE LA MANGUERA DE DE LA MANGUERA HACIA LA DERECHA SUMINISTRO DE AGUA CONECTOR DE AGUA A EL FRIA EN LA VALVULA MEZCLADORA DE AGUA ANILLO SELLADOR 22 GIRANDO LA TUERCA DEL CONECTOR 2 HACIA LA DERECHA TUERCA DEL TUERCA DEL CONECTOR CONECTOR TAPA DEL CONECTOR DE AGUA CALIENTE ASEGURESE QUE EL ANILLO SELLADOR DE GOMA ESTE DENTRO DE LA TUERCA MANGUERA DE DEL CONECTOR DE LA MANGUERA CONECTOR DE AGUA FRIA SI USTED TIENE LAS LLAVES DE SUMINISTRO DE AGUA POR SEPARADO CALIENTE Y FRIA CONECTE LA MANGUERA A LA LLAVE DE AGUA FRIA Y AL CONECTOR DE AGUA F
3. Preset Button 4 Rinse Time Indicator 13 Spin Time Selection Button 5 Spin Time Indicator 14 Rinse Time Selection Button 6 LED Display 15 Wash Time Selection Button 7 Children proof Indicator 16 Water Level Selection Button 8 Function Indicator 17 Water Temperature Selection Button 9 Power Button OPERATING YOUR PORTABLE WASHER PREPARATION 1 Connect the water inlet hose 3 Insert the plug into the 4 Insert the end of drain hose to the water faucet Don t Socket For safety the plug into the hook shelf and hang switch on the power if the should have ground the drain hose over a drain water pressure is lower than connection outlet 0 05MPa and higher than 0 5MPa 2 Openthe water faucet amp 5 Putthe wash load into the 6 Add the suitable quantity 7 Close the lid Otherwise the tub evenly detergent into the detergent 10 BEFORE WASHING Prepare the wash load Mix large and small articles in a load to get the best washing results Drop articles loosely into the inner tub Do not pack articles in or wrap them Articles should move freely through the wash water for best cleaning results Articles should rollover sink and then reappear When washing very large articles do not fill inner tub as full as with other loads The water level in your washer should fit the size of your wash load Small load will use lower water levels There must be enough water in the inner tub to allow articles to move and
4. LAVE PIEZAS MUY GRANDES NO LLENE MUCHO EL CILINDRO DE AGUA EL NIVEL DEL AGUA EN LA LAVADORA NO DEBE SOBREPASAR EL NIVEL DE LA ROPA CARGAS DE ROPA PEQUE AS NECESITAN MENOS AGUA DEBE HABER SUFICIENTE AGUA EN EL CILINDRO COMO PARA QUE LAS PIEZAS SE MUEVAN LIBREMENTE SOBRECARGAR LA LAVADORA PUEDE RESULTAR EN UN MAL LAVADO Y ENJUAGUE LA SOBRECARGA PUEDE CAUSAR QUE LA ROPA SE ARRUGUE O QUE SE HALE DIBUJO NIVEL DE AGUA CORRECTO INCORRECTO FUNCIONES LAS SIGUIENTES FUNCIONES DE LAVADO ESTAN PROGRAMADAS EN LA COMPUTADORA FUNCIONE REMOJO LAVADO ENJUAGUE CENTRIFUGADO FINALIZAR NORMAL 12 MIN 1 CICLO 5 MIN 39 MIN REMOJO 20 MIN 12 MIN 2 CICLOS 5 MIN 66 MIN RAPIDO 6 MIN 1 CICLO 3 MIN 33 MIN JEANS 12 MIN 2 CICLOS 5 MIN 52 MIN SUAVE 12 MIN 2 CICLOS 3 MIN 44 MIN FORZUDO 12 MIN 2 CICLOS 5 MIN 58 MIN SEDAS 6 MIN 2 CICLOS 3 MIN 38 MIN ENJUAGUE 12 MIN 2 CICLOS 5 MIN 58 MIN CUENTA CON 5 MINUTOS PARA ELEGIR Y PRESIONAR EL LOS BOTON ES PARA PROGRAMAR EL MODO DE LAVADO LUEGO PRESIONE START PAUSE PARA REINICIAR LA LAVADORA DE LO CONTRARIO LA LAVADORA SE APAGARA AUTOMATICAMANTE 24 PARA EVITAR RUIDOS MOLESTOS DURANTE EL SECADO CIERRE LA TAPA DE LA LAVADORA NOTA _ LAS PIEZAS DE ROPA DE COLORES QUE DESTI EN DEBEN SER LAVADAS POR SEPARADO PARA EVITAR QUE MANCHEN OTRAS PIEZAS gt 51 DESEA CAMBIAR EL PROGRAMA SELECCIONADO PRESIONE EL BOTON START STOP LUEGO PRESIONE EL BOTON DEL PROGRAMA DESEADO NUEVAMENTE PRESIONE EL BOTON
5. RIESGO DE FUEGO CORTO CIRCUITO O DA OS AL USAR SU LAVADORA PORTATIL gt NO LIMPIE LA LAVADORA PORTATIL CON LIQUIDOS INFLAMABLES EL VAPOR PUEDE CREAR FUEGO O UNA EXPLOSION gt LEA TODAS LAS INSTRUCCIONES ANTES DE USAR SU LAVADORA PORTATIL gt RIESGOS DE QUE LOS NI OS QUEDEN ATRAPADOS DENTRO DE LOS EQUIPOS NO SON PROBLEMAS DEL PASADO NO PERMITA QUE OPEREN JUEGUEN O ENTREN DENTRO DE LA LAVADORA ANTES DE BOTAR O RETIRAR SU LAVADORA ASEGURESE DE QUITARLE LA PUERTA gt COLOQUE LA LAVADORA EN LUGARES HUMEDOS O EXPUESTA AL VAPOR O A LA LLUVIA LA HUMEDAD PUEDE DESTRUIR EL AISLAMIENTO ELECTRICO PUDIENDO CAUSAR UN CHOQUE ELECTRICO gt NO ALMACENE USE GASOLINA U OTRO LIQUIDO GAS INFLAMABLE CERCA DE ESTA U OTRA LAVADORA PORTATIL EL VAPOR PUEDE CREAR FUEGO O UNA EXPLOSION 18 INSTRUCCIONES DE INSTALACION ANTES DE USAR SU LAVADORA gt REMUEVA EL EMPAQUE EXTERIOR E INTERIOR gt NECESITARA LAS SIGUIENTES HERRAMIENTAS LLAVE INGLESA O AJUSTABLE PINZAS ALICATE DESTORNILLADOR ASEGURESE QUE TIENE LAS SIGUIENTES PIEZAS 2 MANGUERAS CON ADAPTADORES PARA EL GRIFO 1 PLACA PARA REDUCIR RUIDO CON TORNILLOS REMUEVA EL PROTECTOR NOTA DEBE GUARDAR Y USARLO CUANDO TENGA QUE MOVER O TRANSPORTAR LA LAVADORA A OTRO LUGAR LIMPIE EL INTERIOR CON UN TRAPO SUAVE Y AGUA TIBIA DEJE 2 PULGADAS DE ESPACIO ENTRE LA PARED Y LA LAVADORA COLOQUE SU ROPA EN LA LAVADORA UNIFORMEMENTE ROPA DESNIVELADA EN LA LAVADORA PODRIA CAUSAR RUIDO O VIBRACI
6. accumulated hydrogen gas As the gas is flammable do not smoke or use an open flame during this time DANGER or WARNING Risk of child entrapment Child entrapment and suffocation are not problems of the past Junked or abandoned appliances are still dangerous even if they will just sit in the garage a few days Before you throw away your old portable washer Take off the lid Never allow children to operate play with or crawl inside the portable washer Close supervision of children is necessary when the washer is used near children Do not reach into the washer if the agitator or inner tub is moving Do not tamper with controls Do not repair or replace any part of the washer or attempt any servicing unless specifically recommended in the user maintenance instructions or in published user repair instructions Never clean portable washer parts with flammable fluids The fumes can create a fire hazard or explosion Do not place the washer in steamy rooms or where the washer is directly exposed to rain Moisture may destroy the electrical insulation causing an electrical shock hazard Do not store use gasoline or any other flammable vapors and liquids in the vicinity of this or any other portable washer The fumes can create a fire hazard or explosion If the power cord is damaged it must be replaced by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard Save these instructions B
7. hot water supplied connect the inlet hoses by matching cold to cold and hot to hot 1 Connectthe water inlet hoses to the faucets by turning the connecting nuts CONNECTING NUT CONNECTING WATER INLET HOSE NUT Be sure the rubber rings are inside the connecting nuts 2 Unscrew the lid of hot water connector in water mixing valve and then connect the other end of water inlet hoses to the connectors in water mixing valve by turning the connecting nuts CONNECTING NUT HOT WATER CONNECTOR WATER INLET HOSE WATER CONNECTION For normal kitchen sink tap only use the inlet hose with cold water inlet Connect the inlet hose to the male hose thread adapter by turning it clockwise to be fixed tightly Make sure to insert the rubber ring enclosed Then connect tightly to your sink Note Some faucets may require you to also use the female hose thread adapter between the male adapter and your sink faucet as shown below Make sure the rubber ring is inserted and connect to your sink Only necessary on some faucets uE Female Hose Thread Adapter e __ Male Adapter lt gt Rubber Ring amp Rubber Ring SeA Male Adapter c Rubber Ring Inlet Hose Inlet Hose If water leaks from faucet connection or washer connection turn off water and tighten fully using a wrench Be careful not to over tighten and damage water connection Turn on water supply and make sure no leaks are present DISCONNECTING THE INLET HO
8. level button to select the appropriate water level setting e Press the START HOLD to start the course And the LED display will show the remaining time of the entire course DELICATES For small laundry e Press down the power button Press the functions button to select the DELICATES function until the DELICATES indicator is ON Press the water supply button to select the water temperature Press the water level button to select the appropriate water level setting The default water level is LOW LEV2 e Press the START HOLD to start the course And the LED display will show the remaining time of the entire course SPRAY RINSE For children laundry e Press down the power button e Press the functions button to select the SPRAY RINSE function until the SPRAY RINSE indicator is ON e Press the water supply button to select the water temperature e Press the water level button to select the appropriate water level setting e Press the START HOLD to start the course And the LED display will show the remaining time of the entire course MANUAL FUNCTIONS WASH ONLY Press down the power button Press the functions button to select the appropriate program Press the water supply button to select the water temperature Press the water level button to select the appropriate water level setting Press the wash button to select the wash time Press the rinse button until all rinse indicators are OFF Press the spin button until al
9. prevent movement of the machine during wash and spin operation NOTE Not all movement will be totally eliminated this is normal A ADJUSTABLE FOOT Caster Fixed foot INSTALLING THE NOISE PROOF PLATE Take the noise proof The opening ofthe Insert the noise proof Lay down the machine plate out ofthe noise proof plate iS plate into the washing and secure the noise proof package of machine base plate by fastening the two setscrews CONNECTING THE WATER SUPPLY HOSE The water supply hose must be connected to the washing machine at one end and to the water faucet at the other Do not stretch the water supply hose If the hose is too short and you do not wish to move the water faucet replace the hose with a longer high pressure hose Select appropriate faucet as shown in the figures below If none of these faucets are available use the faucet adapter provided The end of faucet spout should be longer than 10mm 0 4 or the connector cannot be fixed properly Water leakage could develop 1 Connect the water inlet hose to the faucet by turning the connecting nut CONNECTING NUT Be sure a rubber ring is inside the connecting nut 2 Then connect the other end of water inlet hose to the cold connector in water mixing valve by turning the connecting nut LID OF HOT WATER CONNECTING E CONNECTOR NUT 2 WATER INLET HOSE COLD WATER CONNECTOR If you have both cold and
10. spin The lid is not closed The washer is not on a level surface SERVICE FOR YOUR PORTABLE WASHER We are proud of our customer service organization and the network of professional service technicians that provide service on your Avanti portable washers With the purchase of your Avanti portable washer you can be confident that if you ever need additional information or assistance the Avanti Products Customer Service Team will be here for you Just call us toll free AVANTI PRODUCTS CUSTOMER SERVICES Product Information 800 323 5029 Whatever your questions are about our products help is available Part Orders 800 220 5570 You may order parts and accessories that will be delivered directly to your home by personal check money order Master Card or Visa In Home Repair Service 800 220 5570 An Avanti Products authorized service center will provide expert repair service scheduled at a time that is convenient for you Our trained servicers know your portable washer inside and out WIRING DIAGRAM Microcomputer Controlled Board Assembly BR G WH WH B R BL B BLUE BL BLACK BR BROWN B R RR G GREEN C L GR GRAY T B R R RED Water level sensor 16 WH WHITE Y YELLOW Y O ORANGE P PURPLE YOUR AVANTI PRODUCTS WARRANTY Staple your sales receipt here Proof of original purchase date is needed to obtain service under warran
11. the wash program chart FUNCTION SOAK WASH RINSE SPIN TOTAL TIME Approx NORMAL 12Min 1 Cycle 5 Min 35 Min SOAK 20Min 12Min 2 Cycles 5 Min 66 Min SPEEDY 6 Min Spray Rinse 1 Cycle 3 Min 33 Min JEANS 12Min Spray Rinse 2 Cycles 5 Min 52 Min GENTLE 12Min 2 Cycles 3 Min 44 Min HEAVY 12 Min Spray Rinse 2 Cycles 5 Min 58 Min DELICATES 6 Min 2 Cycles 3 Min 38 Min SPRAY RINSE 12 Min Spray Rinse 2 Cycles 5 Min 58 Min Press down each button within 5 minutes since the program will reset the process group Then press down STRAT HOLD button to re start the washing machine If not the washing machine will shut down automatically Close the lid or the washing machine will not operate In case the unbalance of load triggers the safety switch when spinning the washing machine will automatically refill water to adjust the balance Note e Clothes easily discolored should be washed separately so as to prevent inter dyeing e f you want to change a selected program please press the START HOLD button first then press the Program button before pushing START HOLD button e When Rinse Drain program is ON do not use detergent e f you want to drain water during washing press the START HOLD button then select Rinse and Drain program Press START HOLD button again to restart DELAY START SETTING Select this course when you have to go out or do something else e Press down the power button e Load the washing ma
12. volver a funcionar normalmente ENCENDIDO POWER NIVEL DE AGUA WATER LEVEL PRESIONE EL BOTON HASTA QUE SE ILUMINE EL NIVEL DE AGUA APROPIADO PARA LA CANTIDAD DE ROPA QUE VA ALAVAR TEMPERATURA DEL AGUA PRESIONE EL BOTON COLD PARA AGUA FRIA O HOT PARA CALIENTE SI AMBAS LUCES SE ILUMINAN SIGNIFICA QUE ESCOGIO AGUA TIBIA 23 NOTA EL ENJUAGUE ES SIEMPRE CON AGUA FRIA IMPORTANTE PARA PODER SELECCIONAR LA TEMPERATURA UD DEBE CONTAR CON DOS ENTRADAS DE AGUA UNA PARA AGUA FRIA Y OTRA PARA CALIENTE PROGRAMAS DE LAVADO PROGRAM PRESIONE HASTA QUE SE ILUMINE EL PROGRAMA DESEADO DE ACUERDO A LA CARGA DE ROPA QUE VAYA A LAVAR FUNCION FUNCTION PRESIONE EL BOTON FUNCTION HASTA QUE SE ILUMINE LA FUNCION DESEADA INICIAR DETENER START STOP PRESIONE EL BOTON START STOP UNA VEZ PARA INICIAR EL FUNCIONAMIENTO PARA DETENERLO PRESIONE START STOP NUEVAMENTE SI CONTINUA FUNCIONANDO PRESIONELO OTRA VEZ EL NIVEL DE AGUA PUEDE SER MODIFICADO DURANTE LA OPERACION SI DESEA UN NIVEL MAS ALTO DE AGUA LA LAVADORA EMPEZARA A FUNCIONAR UNA VEZ QUE HAYA LLEGADO AL NIVEL DE AGUA DESEADO ANTES DE LAVAR PREPARE LA CARGA DE ROPA A LAVAR MEZCLE PIEZAS PEQUE AS Y GRANDES PARA OBTENER MEJORES RESULTADOS DEPOSITE LAS PIEZAS DENTRO DEL CILINDRO NO EMPAQUE LAS PIEZAS NI LAS ENVUELVA LAS PIEZAS DEBEN MOVERSE LIBREMENTE DENTRO DEL AGUA PARA OBTENER MEJORES RESULTADOS LAS PIEZAS DEBEN RODAR HUNDIRSE Y REAPARECER CUANDO
13. CUL Listed 3 wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and at least 10 amperes SURGE PROTECTOR Most electrical appliances use a series of electric control boards to operate These boards are very susceptible to power surges and could be damaged or destroyed If the appliance is going to be used in an area or if your city country is prone to power surges outages it is suggested that you use a power surge protector for all electrical devices appliances you use The surge protector that you select must have a surge block high enough to protect the appliance it is connected to If you have any questions regarding the type and size of surge protector needed contact a licensed electrician in your area Damages due to power surges are not considered a manufacturer covered defect and will void your product warranty CONTROL PANEL COLD POWER HS _START WARM s SOAK J Normat GENTLE ED SPRAY TIME f Yf MED L3 2 MIN SRRA 5 MIN soak SPEEDY DELICATES f sPRAYY Levi 3 P lt gt lt Low PRESET smn P T T s 1 cHio PROOF 1 Walter Temperature Indicator 10 START HOLD Button 2 Water Level Indicator 11 Function Selection Button 3 Wash Time Indicator 12
14. DE SER COLOCADA EN EL PISO EL BANO O LA BANERA SIEMPRE QUE LA ALTURA NO SEA MAYOR A 70 CM EL PUNTO MAS ALTO DE LA MANGUERA DE DRENAJE DEBE SER 70 120 CM SOBRE EL NIVEL DEL PISO DE LO CONTRARIO LA LAVADORA NO PODRA FUNCIONAR CORRECTAMENTE MODO DE EMPLEO PREPARACION 1 CONECTE LA MANGUERA AL GRIFO DE SUMINISTRO DE AGUA 2 ABRA EL GRIFO DE SUMINISTRO DE AGUA NO ENCIENDA LA LAVADORA SI LA PRESION ES MENOR A 0 02MPA O MAYOR A 0 5MPA 3 CONECTE EL CABLE DE ELECTRICIDAD EN EL TOMACORRIENTE POR SU SEGURIDAD EL TOMACORRIENTE DEBE TENER UNA CONEXION PARA EL CABLE DE TIERRA 4 INSERTE EL EXTREMO DE LA MANGUERA DE DRENAJE EN LA PLATAFORMA DE CONEXION CUELGUE EL OTRO EXTREMO DE LA MANGUERA EN UN RECIPIENTE DE DRENAJE TINA DEL BANO LAVADERO ETC 5 COLOQUE LA CARGA DE ROPA A LAVAR DENTRO DEL CILINDRO Y CIERRE LA TAPA LA FUNCION DE LAVADO PUEDE CONTINUAR CON LA TAPA ABIERTA PERO ES MEJOR CERRARLA ANTES QUE EMPIECE LA FUNCION DE SECADO CENTRIFUGA 6 ANADA UNA CANTIDAD ADECUADA DE DETERGENTE EN EL DISPENSADOR COLOQUE LOS ARTICULOS A LAVAR EN EL CILINDRO INTERNO Y CIERRE LA TAPA DE LA LAVADORA EL CICLO DE LAVADO SE PUEDE REALIZAR CON LA PUERTA ABIERTA A DIFERENCIA DEL CICLO DE SECADO CENTRIFUGA EN QUE LA PUERTA DEBE ESTAR CERRADA INSTRUCCIONES PARA OPERAR LA LAVADORA AVISO Si Ud abra la tapa mientras que la lavadora est funcionando la lavadora parar de funcionar en 7 segundos En cuanto Ud cierre la tapa la lavadora
15. EFORE USING YOUR PORTABLE WASHER INSTALLATION INSTRUCTIONS SCREWDRIVER Remove the exterior and interior packing You will need the following tools e Wrench e Pliers e Screwdriver Check to be sure you have all of the following parts PLIERS e 2 Inlet Hoses e 2 Faucet Adapters e 1 Noise Proof Plate With Screws e 4 Casters Remove shipping brace Note It should be saved and used to prevent damage to washer components whenever washer is moved or transported to a new location Clean the interior surface with lukewarm water using a soft cloth Allow 2 inches of space between the back and sides of the appliance e Put your laundry into the washer evenly Uneven laundry may cause noise or vibration e Don t use excessively hot water 50 C or more Plastic parts may be deformed or damaged Also clothing may be deformed or bleached e Before washing check all pockets If nails or pins remain in pockets they may damage the washer or clothes e Never splash water on the control panel e Plug the washer into an exclusive properly installed grounded wall outlet Do not under any circumstances cut or remove the third ground prong from the power cord Any questions concerning power and or grounding should be directed toward a certified electrician or an authorized Avanti Products service center SELECTING A LOCATION Before you install the portable washer select a location with the following characteristics e A ha
16. LA CAJA DE FUSIBLES EN SU CASA LA LLAVE DE AGUA PUEDE ESTAR CERRADA NO ENTRA AGUA O EL NIVEL ES MUY BAJO LA LLAVE DE AGUA PUEDE ESTAR CERRADA LA MANGUERA DE ENTRADA DEL AGUA ESTA CONGELADA O PUEDE ESTAR DOBLADA EL FILTRO EN EL CONECTOR DE LA LLAVE O LA VALVULA DE SUMINISTRO PUEDEN ESTAR OBSTRUIDOS LA LAVADORA NO DESAGUA LA MANGUERA DE DESAG E ESTA OBSTRUIDA O APLASTADA I EL FILTRO DE LA MANGUERA DE DESAG E PUEDE ESTAR OBSTRUIDO LA LAVADORA VIBRA O HACE MUCHO RUIDO VERIFIQUE QUE LA LAVADORA ESTE NIVELADA LA LAVADORA ESTA TOCANDO OTRO OBJETO SEPARELA LA CARGA DE ROPA NO ESTA BIEN DISTRIBUIDA ADVERTENCIA EL CABLE DE ELECTRICIDAD DEBE SER DESCONECTADO DESPUES DE USAR LA LAVADORA USE DETERGENTE EN POLVO DE POCA ESPUMA NO PERMITA QUE LOS NINOS JUEGUEN CON LA LAVADORA 26 Registration Information Thank you for purchasing this fine Avanti product Please fill out this form and return it to the following address within 100 days from the date of purchase and receive these important benefits Avanti Products A Division of The Mackle Co Inc P O Box 520604 Miami Florida 33152 gt Protect your product We will keep the model number and date of purchase of your new Avanti product on file to help you refer to this information in the event of an insurance claim such as fire or theft gt Promote better products We value your input Your responses will help us develop produc
17. ON NO USE AGUA DEMASIADO CALIENTE 50 C O MAS YA QUE LAS PARTES PLASTICAS PODRIAN DEFORMARSE O DANARSE Y LA ROPA PODRIA DEFORMARSE O DESTENIRSE gt ANTES DE LAVAR REVISE Y VACIE TODOS LOS BOLSILLOS CLAVOS ALFILERES ETC ESTOS OBJETOS PUEDEN DANAR LA LAVADORA O SU ROPA gt NO SALPIQUE AGUA AL PANEL DE CONTROL gt CONECTE LA LAVADORA A UN ENCHUFE DE PARED EXCLUSIVO CON CONEXION A TIERRA BAJO NINGUNA CIRCUNSTANCIA REMUEVA O CORTE LA TERCERA PUNTA DEL ENCHUFE CONEXION A TIERRA DIRIJA CUALQUIER PREGUNTA RELACIONADA CON LA ELECTRICIDAD O CONEXION A TIERRA A UN ELECTRICISTA CERTIFICADO O A UN CENTRO DE SERVICIO AUTORIZADO POR AVANTI v VVV vv SELECCIONE UN LUGAR ANTES DE INSTALAR SU LAVADORA SELECCIONE UN LUGAR CON LAS SIGUIENTES CARACTERISTICAS gt SUPERFICIE PLANA Y DURA SI LA SUPERFICIE ES IRREGULAR VEA AJUSTE DE PATAS NIVELADORAS LEJOS DE LA LUZ SOLAR DIRECTA LA LUZ SOLAR DIRECTA PUEDE AFECTAR LA CAPA ACRILICA COMPONENTES PLASTICOS Y ELECTRICOS gt VENTILACION ADECUADA LEJOS DE LAS FUENTES DE CALOR TALES COMO CARBON O GAS gt ASEGURESE QUE LA LAVADORA NO ESTE APLASTANDO EL CORDON ELECTRICO LAS APERTURAS DE VENTILACION DEBEN ESTAR LIBRES DE OBSTRUCCIONES TALES COMO ALFOMBRA AJUSTE DE PATAS NIVELADORAS SI EL PISO ES IRREGULAR AJUSTE LAS PATAS NO INSERTE PEDAZOS DE MADERA U OTROS OBJETOS BAJO LAS PATAS DESENROSQUE EL TORNILLO GIRANDOLO CON LA MANO HASTA QUE LLEGUE A LA ALTURA DESEADA AJU
18. RIA EN LA VALVULA MEZCLADORA DE AGUA HAGA LO MISMO CON EL AGUA CALIENTE Y LA SEGUNDA MANGUERA 1 CONECTE LAS MANGUERAS DE 2 REMUEVA LAS TAPAS DE LOS SUMINISTRO DE AGUA A LOS GRIFOS CONECTORES DE AGUA FRIA Y GIRANDO LAS TUERCAS DE LOS CALIENTE DE LA UNIDAD Y CONECTE CONECTORES DE LAS MANGUERAS LOS OTROS EXTREMOS DE LAS HACIA LA DERECHA MANGUERAS DE SUMINISTRO DE AGUA A LOS CONECTORES DE AGUA RESPECTIVOS EN LA VALVULA MEZCLADORA DE AGUA GIRANDO LAS TUERCA DEL TUERCAS DE LOS CONECTORES HACIA LA DERECHA MANGUERA DE TUERCA DEL SUMINISTRO CONECTOR TUERCA DEL ASEGURESE DE COLOCAR EL ANILLO PERS 33 CONECTOR DE SELLADOR DENTRO DE LAS TUERCAS DE LOS CONECTORES DE LAS MANGUERA DE MANGUERAS CONECTOR DE AGUA FRIA 22 DESCONECTANDO LA MANGUERA DE SUMINISTRO DE AGUA DEBIDO A LA ALTA PRESION DE LA LLAVE AUN CUANDO ESTA CERRADA RECOMENDAMOS DESCONECTAR LA MANGUERA YA QUE PODRIA CAUSAR GOTEO O SALPICADURA PARA EVITARLO SIGA ESTAS INSTRUCCIONES 1 CIERRE LA LLAVE DEL AGUA 2 ENCIENDA LA LAVADORA 3 APAGUELA LUEGO DE 5 SEGUNDOS APROXIMADAMENTE 4 RETIRE LAS MANGUERAS GIRANDO LAS TUERCAS DEL CONECTOR HACIA LA IZQUIERDA SI LA LAVADORA ES USADA FRECUENTEMENTE NO RETIRE LAS CONEXIONES PARA EVITAR POSIBLES DANOS COLOCANDO LA MANGUERA DE DRENAJE CONECTE LA MANGUERA DE DRENAJE A LA SALIDA DE AGUA DE LA LAVADORA Y AJUSTELA CON UNA GRAMPA AJUSTABLE COMO PUEDE DRENAR HACIA ARRIBA O HACIA ABAJO LA MANGUERA DE DRENAJE PUE
19. SE Dismantling the hose directly may cause water to splash due to the possible high water pressure in the hose even after the faucet has been turned off Please take off the hose as per following steps even if the faucet is closed e Turn off the faucet lt e Turn on the power let the machine run for about 5 seconds then turn it off e Remove the connecting nuts from the faucet and washing machine CONNECTING NUT Note If the washing machine is frequently used it is not necessary to dismantle the inlet hose to avoid possible damage to the screws POSITIONING THE DRAIN HOSE Connect the drain hose to the water outlet of the washing machine then fasten it with a pinchcork Since only up drainage is available drain hose can be hung in the basin or bathtub NOTE The highest point of the drain hose must be in the height of 0 7 1 2m above floor level otherwise the washer cannot work normally ELECTRICAL CONNECTION A Warning Improper use of the grounded plug can result in the risk of electrical shock If the power cord is damaged have it replaced by an authorized Avanti Products service center This appliance should be properly grounded for your safety The power cord of this appliance is equipped with a three prong plug which mates with standard three prong wall outlets to minimize the possibility of electrical shock Do not under any circumstances cut or remove the third ground prong from the power cord supp
20. START STOP gt A ADA DETERGENTE PARA EL CICLO DE ENJUAGUE Y DESAGUE gt 51 DESEA BOTAR EL AGUA DURANTE EL CICLO DE LAVADO PRESIONE EL BOTON START STOP LUEGO PRESIONE EL BOTON DE RINSE NUEVAMENTE PRESIONE EL BOTON START STOP MANTENIMIENTO LIMPIE REGULARMENTE LA SUPERFICIE DE SU LAVADORA CON UN PA O SUAVE LIMPIE EL CILINDRO INTERNO DE LAVADO CON UN PA O SUAVE ESPECIALMENTE DESPUES DE LAVAR CON ALMIDON O CLORO LIMPIE EL FILTRO QUE SE ENCUENTRA EN LA VALVULA DE SUMINISTRO DE AGUA PARA PREVENIR POSIBLES OBSTRUCCIONES 1 DESCONECTE EL ENCHUFE 2 RETIRE LA MANGUERA DE SUMINISTRO DE AGUA Y LIMPIE EL FILTRO CON UN CEPILLO LIMPIANDO EL FILTRO DE PELUSAS 1 SAQUE EL FILTRO HALANDOLO HACIA ARRIBA LAVE Y ENJUAGUE EL FILTRO CUIDADOSAMENTE REINSTALE EL FILTRO NUEVAMENTE MANTENIMIENTO DE INVIERNO 1 CIERRE LA LLAVE DEL AGUA DESCONECTE LAS MANGUERAS DE SUMINISTRO DE AGUA Y DEJELA DRENAR POR COMPLETO 2 ACTIVE EL CICLO DE SECADO POR UN MINUTO 3 APAGUE LA LAVADORA Y DESCONECTELA DE LA ELECTRICIDAD 25 SI TIENE PROBLEMAS CON SU LAVADORA PORTATIL UD PUEDE RESOLVER MUCHOS PROBLEMAS FACILMENTE AHORRANDOSE EL COSTO DEL SERVICIO TECNICO PRUEBE LAS SIGUIENTES SUGERENCIAS PARA VER SI PUEDE RESOLVER LOS PROBLEMAS ANTES DE LLAMAR AL SERVICIO TECNICO GUIA PARA LA SOLUCION DE PROBLEMAS PROBLEMA REVISAR LA LAVADORA NO FUNCIONA VERIFIQUE QUE ESTE CONECTADA A LA ELECTRICIDAD REVISE
21. STE LA TUERCA CON LA LLAVE INGLESA COLOQUE LA LAVADORA EN UNA SUPERFICIE PLANA Y FIRME SI COLOCA LA LAVADORA EN UNA SUPERFICIE IRREGULAR O BLANDA PODRIA CAUSAR DANO O VIBRACION PARA PORTABILIDAD LA LAVADORA VIENE CON CUATRO RUEDAS FACILES DE INSTALAR PARA AYUDAR AL MOVIMIENTO DE LA LAVADORA HACIA Y DESDE EL LAVADERO ACUESTE LA UNIDAD SOBRE LA PARTE TRASERA E INSTALE LAS RUEDAS EN LA PARTE DE ABAJO DE LA BASE COMO MUESTRAN LAS FIGURAS DEBAJO EN ESTA PAGINA REGRESE LA UNIDAD A LA POSICION VERTICAL CUANDO LA MAQUINA ESTE COLOCADA PARA FUNCIONAMIENTO AJUSTE LA PATAS A UNA ALTURA UN POCO MAYOR A LAS RUEDAS PARA EVITAR QUE LA LAVADORA SE MUEVA DURANTE EL LAVADO 19 NOTA AUN HACIENDO LO ANTERIOR LA LAVADORA PODRIA MOVERSE ESTO ES NORMAL INSERTE LA BANDEJA A PRUEBA DE RUIDO EN LA BASE DE LA LAVADORA 1 REMOVER LA PLATAFORMA A PRUEBA DE RUIDO DE LA CAJA 3 LAAPERTURA PARA LA PLATAFORMA A PRUEBA DE RUIDOS ESTA EN LA 4 RECUESTE LA LAVADORA PARA COLOCAR LA PLATAFORMA A PRUEBA DE RUIDOS FIJANDOLA CON DOS TORNILLOS 2 RECUESTE LA LAVADORA DE MANERA QUE LE SEA FACIL AJUSTAR LOS DOS TORNILLOS DE SEGURIDAD PARA EVITAR QUE LA BANDEJA SE SALGA DEL LUGAR PARTE INFERIOR DE LA LAVADORA REMOVIENDO EL PROTECTOR _ PARA PREVENIR QUE LA LAVADORA SE DANE RECOMENDAMOS QUE GUARDE EL PROTECTOR Y LO USE CUANDO NECESITE MOVER O TRANSPORTAR SU LAVADORA 20 Conexi n El ctrica A ADVER
22. TENCIA EL USO INAPROPIADO DEL ENCHUFE A TIERRA PUEDE OCASIONAR RIESGO DE UN CHOQUE ELECTRICO SI EL CORDON SE DA ASE LLEVELO A UN CENTRO DE SERVICIO AUTORIZADO POR AVANTI PRODUCTS PARA QUE SE REEMPLACE e Para su seguridad esta m quina de hacer hielo debe estar apropiadamente conectada a tierra El cord n el ctrico de esta m quina de hacer hielo esta equipado con un enchufe de tres puntas el cual encaja perfectamente en los recept culos enchufes de pared de tres puntas est ndar para minimizar la posibilidad de un choque el ctrico e Bajo ninguna circunstancia corte o retire la tercera punta cable a tierra del enchufe del cord n el ctrico e Nunca use un cable de extensi n para conectar la unidad a la electricidad e Nunca use un adaptado con enchufe de solo 2 puntas e Si solo puede conectar la m quina de hacer hielo a un recept culo enchufe de pared de 2 puntas comun quese con un electricista calificado para que reemplace ese recept culo enchufe de pared por uno de 3 puntas de acuerdo con los c digos de electricidad aplicables e Esta m quina de hacer hielo requiere un receptaculo enchufe de pared de tres puntas est ndar de 115 120 voltios a c 60hz e Para prevenir cualquier da o f sico o lesi n el cord n debe ser asegurado detr s de la m quina de hacer hielo y no estar expuesto o colgando Cable de Extensi n Debido al posible riesgo de seguridad causado bajo ciertas circunstancias se recomienda fir
23. chine and select the appropriate wash program e Press PRESET button continuously to select the delay start time From 1 hour to 24 hours e Close the lid completely e Press START HOLD button to start the course CHILDREN PROOF SETTING Select the function the program will hold the washing machine and give out alert voice once the lid is opened when washing And the washing machine will automatically drain water and give alarm if the lid is not closed in 10 seconds In case a child falls into the washing machine when he plays around he will be in safe status e Press down the power button e Select the appropriate program and press START HOLD button to start the washing machine e The washing machine buzzer will give out music and the digital indicator 3 This time you must decide whether to select the function or not 14 e Press the PRESET button to select the function and the dot indicator will be ON If no don t do anything NOTE If you open the lid while the machine in running all operations will be stopped within 7 seconds To resume operation close the lid CARE AND MAINTENANCE CLEANING YOUR PORTABLE WASHER e Clean the surface of your portable washer regularly with soft fabric e Clean the inner tub regularly especially immediately after starch or bleach operation e Clean the filter in the inlet valve or inlet hose regularly in order to prevent it from clogging Unplug the power cord 2 Remove the
24. i FL 33172 USA PARTS 8 FEATURES EEC ICCC 11 eJ 5 2 12 gt 13 DETERGENT CASE SOFTENER DISPENSER INNER TUB CONTROL PANEL BASE NOISE PROOF PLATE INLET HOSE 2 PCS 8 LINT FILTER 9 PULSATOR 10 POWER SUPPLY CORD 11 DRAIN HOSE 1 PC 12 LEVEL ADJUSTABLE KNOB 13 ADJUSTABLE FOOT NOaRWN gt ACCESSORIES INLET HOSE NOISE PROOF PLATE FAUCET ADAPTER CASTER 2 PIECES 1 PIECE 2 PIECES 4 PIECES IMPORTANT SAFETY INSTRUCTIONS MWARNING y To reduce the risk of fire electrical shock or injury when using your portable washer follow these basic precautions Read all instructions before using the portable washer Do not wash articles that have been previously cleaned in washed in soaked in or spotted with gasoline dry cleaning solvents or other flammable or explosive substances as they give off vapors that could ignite or explode Do not add gasoline dry cleaning solvents or other flammable or explosive substances to the wash water These substances give off vapours that could ignite or explode Under certain conditions hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more HYDROGEN GAS IS EXPLOSIVE If the hot water system has not been used for such a period before using a washing machine turn on all hot water faucets and let water flow from each for several minutes This will release any
25. inlet hose and clean e Clean the surface of the filter with a brush the washing machine with a soft cloth regularly e Clean the inner tub regularly especially after washing starched or bleached laundry 1 Pull upward to remove the 2 Clean and rinse it thoroughly 3 Reinstall lint filter e Vacation time Turn off the tap remove 2 Setspin cycle for 1 3 Unplug the power cord water inlet hose and let minute water drain out from the 15 PROBLEMS WITH YOUR PORTABLE WASHER You can solve many common portable washer problems easily saving you the cost of a possible service call Try the suggestions below to see if you can solve the problem before calling the servicer TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE Washer does not operate Not plugged in The circuit breaker tripped or a blown fuse The lid is not closed Make sure the water source is turned on No water or insufficient water supply The water source faucet is not turned on The water source hose is frozen The water intake hose is bent The filter on the water intake hose is clogged The washing machine does not drain The drain hose is squashed or bent The water hose mesh filter is clogged Washing machine vibrates or is too noisy Check to assure that the washer is level The washing machine is touching another object The laundry load is not balanced Washing machine does not
26. is intended to help you operate and maintain your new portable washer properly Keep it handy to answer your questions If you don t understand something or you need more assistance please call Avanti Customer Service 800 220 5570 Keep proof of original purchase date such as your sales slip with this guide to establish the warranty period Write down the model and serial numbers You ll find them on a plate located on the rear outside wall of the portable washer Please write these numbers here Date of Purchase Model Number Serial Number Use these numbers in any correspondence or service calls concerning your portable washer If you received a damaged portable washer immediately contact the dealer or builder that sold you the portable washer Save time and money Before you call for service check the Troubleshooting Guide It lists causes of minor operating problems that you can correct yourself IF YOU NEED SERVICE We re proud of our service and want you to be pleased If for some reason you are not happy with the service you receive here are some steps to follow for further assistance FIRST contact the people who serviced your portable washer Explain why you are not pleased In most cases this will solve the problem NEXT if you are still not pleased write all the details including your telephone number and send it to Customer Service Avanti Products 10880 NW 30 Street Miam
27. l spin indicators are OFF Press the START HOLD to start the course And the LED display will show the remaining time of the entire course WASH AND RINSE Press down the power button Press the functions button to select the appropriate program Press the water supply button to select the water temperature Press the water level button to select the appropriate water level setting Press the wash button to select the wash time Press the rinse button to select the rinse times Press the spin button until all spin indicators are OFF Press the START HOLD to start the course And the LED display will show the remaining time of the entire course RINSE AND SPIN Press down the power button Press the water level button to select the appropriate water level setting Press the wash button until all wash indicators are OFF Press the rinse button to select the rinse times Press the spin button to select the spin time Press the START HOLD to start the course And the LED display will show the remaining time of the entire course 13 SPIN ONLY e Press down the power button e Press the wash button until all wash indicators are OFF e Press the rinse button until all rinse indicators are OFF e Press the spin button to select the spin time e Press the START HOLD to start the course And the LED display will show the remaining time of the entire course FUNCTIONS Each wash set is programmed in the computer see the details in
28. lied For personal safety this appliance must be properly grounded This appliance requires a standard 115 120 Volt AC 60Hz electrical ground outlet with three prong Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded When a standard 2 prong wall outlet is encountered it is your responsibility and obligation to have it replaced with a properly grounded 3 prong wall outlet The cord should be secured behind the appliance and not left exposed or dangling to prevent accidental injury The appliance should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating label on the appliance This provides the best performance and also prevent overloading house wiring circuits that could cause a fire hazard from overheated Never unplug the appliance by pulling the power cord Always grip the plug firmly and pull straight out from the receptacle Repair or replace immediately all power cords that have become frayed or otherwise damaged Do not use a cord that shows cracks or abrasion damage along its length or at either end When moving the appliance be careful not to damage the power cord gt EXTENSION CORD Because of potential safety hazards under certain conditions it is strongly recommended that you do not use an extension cord with this appliance However if you must use an extension cord it is absolutely necessary that it be a UL
29. memente que no use un cable de extensi n para este electrodom stico Sin embargo si no tiene otra opci n mas que usar un cable de extensi n aseg rese que este sea un cable de extensi n para electrodom sticos que este listado bajo UL CUL que tenga enchufe y recept culo para enchufe de tres puntas cable a tierra y que la capacidad del cord n el ctrico sea de 115 voltios y no menos de 10 amperios PANEL DE CONTROL ote R Nf _ START Normal GENTLE Ob MN ET soak Heavy POWER COLD 7 9 bes HIGH 1 ni HOT MED 1 12MIN Sige 5 MIN H H PRESET to I eun MIN C2 amin MIN mr sPEEDY beuicares v WATER 6 MIN 1 1MIN cHppROOF JEANS o WATER NATER H WASH RIE SPIN PRESET FICTIONS 6606 e o O 1 INDICADOR DE TEMPERATURA DEL 10 BOTON DE COMENZAR PARAR LAVADO AGUA 2 INDICADOR DEL NIVEL DE AGUA 11 BOTON DE FUNCIONES MODOS DE LAVADO 3 INDICADOR DEL MODO DE LAVADO 12 BOTO DE PREPROGRAMADO 4 INDICADOR DE FUNCION O PROCESO 13 BOTON DE CENTRIFUGADO 5 INICIO PAUSA INICIA DETIENE O 14 BOTON EN ENJUAGAR REINICIA EL CICLO DE LAVADO 6 PANTALLA ELECTRONICA 15 BOTON DE LAVADO 7 INDICADOR A PRUEBA DE NINOS 16 BOTON DE NIVEL DE AGUA 8 INDICADOR DE FUNCIONES 17 BOTON DE SUMINISTRO DE AGUA 9 BOTON DE PRENDER APAGAR 21
30. n select different WASH RINSE and SPIN combinations according to your needs 11 PRESS DOWN PRESET BUTTON Press this button for delay start setting and children proof setting PRESS DOWN FUNCTIONS SELECTION BUTTON Choose the desired function and then the corresponding indicator blink PRESS DOWN START HOLD BUTTON ONCE AND THE MACHINE WILL BEGIN OPERATION Please press this button to stop the normal operation if it continues to work press it again Water level can be reset during the normal operation If the higher water level is selected the machine will operate after refilling the water level selected AUTOMATIC WASH PROGRAMS NORMAL For normal laundry e Press down the power button e The NORMAL indicator will be ON NORMAL is the default program e Press the water supply button to select the water temperature e Press the water level button to select the appropriate water level setting The default water level is HIGH e Press the START HOLD to start the course And the LED display will show the remaining time of the entire course SOAK For dirty laundry e Press down the power button Press the functions button to select the SOAK function until the SOAK indicator is ON Press the water supply button to select the water temperature Press the water level button to select the appropriate water level setting Press the START HOLD to start the course And the LED display will show the remaining time of the entire cour
31. rd level surface if the surface is uneven see Adjusting The Adjustable Foot e Away from direct sunlight Direct sunlight may affect the acrylic coating plastic and electrical components e Adequate ventilation e Away from sources of heat such as coal or gas Make sure that the washing machine does not stand on its power cord Ventilation openings must not be obstructed by carpeting when the portable washer is installed on a carpeted floor ADJUSTING THE ADJUSTABLE FOOT If the floor is uneven adjust the adjustable foot do not insert pieces of wood M or any other objects under the feet a I Loosen the adjustable foot by turning the level adjustable knob with your S E hand until it is at the desired height 2 Tighten the adjustable foot by turning the level adjustable knob in the reverse direction LOOSEN TIGHTEN Place the washer on a sturdy flat surface If the washer is placed on an uneven or weak surface noise or vibration TL KOH occurs Allowable is 1 For portable applications the washing machine comes equipped with four north south casters that can easily be installed to assist in the movement of the machine to and from the sink Lay the unit on its back Install the casters _ into the bottom of the base as indicated Return the machine to the upright position When the machine is positioned Caster for operation set the height of the adjustment foot slightly higher than the front caster to
32. se SPEEDY For light dirty laundry e Press down the power button Press the functions button to select the SPEEDY function until the SPEEDY indicator is ON Press the water supply button to select the water temperature Press the water level button to select the appropriate water level setting Press the START HOLD to start the course And the LED display will show the remaining time of the entire course JEANS For massive laundry e Press down the power button Press the functions button to select the JEANS function until the JEANS indicator is ON Press the water supply button to select the water temperature Press the water level button to select the appropriate water level setting Press the START HOLD to start the course And the LED display will show the remaining time of the entire course GENTLE For elaborate laundry e Press down the power button Press the functions button to select the GENTLE function until the GENTLE indicator is ON Press the water supply button to select the water temperature Press the water level button to select the appropriate water level setting Press the START HOLD to start the course And the LED display will show the remaining time of the entire course HEAVY For big laundry e Press down the power button e Press the functions button to select the HEAVY function until the HEAVY indicator is ON 12 e Press the water supply button to select the water temperature e Press the water
33. ts designed to best meet your future needs Avanti Registration Card Name Model Serial Address Date Purchased Store Dealer Name City State Zip E mail Address Area Code Phone Number Occupation Did You Purchase An Additional Warranty As your Primary Residence Do You O Extended L Own O Rent O None Your Age Reason for Choosing This Avanti Product O under 18 18 25 26 30 Please indicate the most important factors O 31 35 36 50 over 50 That influenced your decision to purchase Marital Status this product O Married L Single O Price O Product Features Is This Product Used In The O Avanti Reputation O Home Business O Product Quality L Salesperson Recommendation How Did You Learn About This Product L Other O Advertising O Friend Relative Recommendation O In Store Demo O Warranty Personal Demo L Other Comments 27 VER W798SS 1 2 0 03282011 PRINTED IN CHINA 28
34. turn over freely Overloading the inner tub can result in poor washing and rinsing Overloading may also cause wrinkling and tearing of articles OPERATION INSTRUCTIONS PRESS DOWN POWER BUTTON PRESS DOWN WATER LEVEL BUTTON Choose appropriate water level according to wash load quantity WATER TEMPERATURE CHOICE Press down the water temperature selection button you can choose to inlet cold water or hot water When the cold water indicator and the hot water indicator turn on simultaneously which means you chose the warm water NOTE The washer will provide a cold rinse in all TEMPERATURE settings IMPORTANT A single cold hose system does not allow the washing machine to automatically select regulate incoming water temperatures to match those listed on the control panel such as WARM or HOT PRESS DOWN WASH TIME SELECTION BUTTON Press down wash time selection button to select the wash time You can also press the button to select soak NOTE When all indicators are OFF the wash cycle is finished PRESS DOWN RINSE TIMES SELECT BUTTON Press this button to select the times of rinse When SPRAY RINSE is selected the washing machine will spray water to rinse firstly during rinse course NOTE When all indicators are OFF the rinse cycle is finished PRESS DOWN SPIN TIME SELECT BUTTON Press this button to select the time of spin NOTE When all indicators are OFF the spin cycle is finished IMPORTANT NOTE You ca
35. ty WHAT IS COVERED LIMITED ONE YEAR WARRANTY For one year from the date of purchase by the original owner Avanti Products will at its option repair or replace any part of the appliance that proves to be defective in material or workmanship under normal use During this period Avanti Products will provide all parts and labor necessary to correct such defects free of charge so long as the appliance has been installed and operated in accordance with the written instructions in this manual In rental or commercial use the warranty period is 90 days LIMITED 5 YEAR WARRANTY ON PLASTIC TUB After one year and until five years from date of purchase Avanti will furnish a replacement plastic tub for one which is defective in material or workmanship You will be responsible for labor LIMITED 7 YEAR WARRANTY ON STAINLESS STEEL TUB After one year and until seven years from date of purchase Avanti will furnish a replacement stainless steel tub for one which is defective in material or workmanship You will be responsible for labor WHAT IS NOT COVERED Incidental or consequential damages Service calls to Correct the installation of your washer Instruction on how to use your washer Replace house fuses or incorrect house wiring or plumbing Repairs performed by unauthorized servicers Repairs when your washer is used in other than normal single family household use 17 e Service calls that are related to e
36. xternal problems such as abuse misuse inadequate electrical power accidents fire floods or acts of God e Failure of the product if it is used for other than its intended purpose e Pickup and delivery e Repairs caused by unauthorized modifications made to the appliance e This warranty does not apply outside the Continental U S A INSTRUCCIONES EN ESPA OL LAVADORA AUTOMATICA DE ROPA LEA TODAS LAS INSTRUCCIONES ANTES DE USAR ESTA LAVADORA Y GUARDE ESTE MANUAL EN UN LUGAR SEGURO PARA REFERENCIA FUTURA CONOCIENDO LAS PARTES DE SU LAVADORA AUTOMATICA DISPENSADOR DEL DETERGENTE DISPENSADOR DEL SUAVIZANTE DE ROPA CILINDRO INTERNO DE LAVADO PANEL DE CONTROL BASE PLATAFORMA A PRUEBA DE RUIDO SE INSERTA EN LA BASE PARA REDUCIR EL NIVEL DE RUIDO Y ALEJA MALOS OLORES Y PLAGAS 7 MANGUERA DE SUMINISTRO DE AGUA CIERRE LA LLAVE DESPUES DE LLENAR EL CILINDRO 8 FILTRO PARA PELUSAS 9 PROPULSOR 10 ENCHUFE Y CABLE DE ELECTRICIDAD 11 MANGUERA DE DRENAJE TOME EN CUENTA QUE DURANTE EL FUNCIONAMIENTO DE LA LAVADORA EL PUNTO MAS ALTO DE LA MANGUERA DE DRENAJE DEBE ESTAR ENTRE 70 Y 120CM SOBRE EL NIVEL DEL PISO 12 BOTON DE AJUSTE DE NIVEL 13 PATA DE AJUSTE ACCESORIOS MANGUERA DE PLATAFORMA A ADAPTADOR RUEDA SUMINISTRO DE AGUA PRUEBA DE RUIDO O 2 PIEZAS 1 PIEZA 2 PIEZAS 4 PIEZAS ADVERTENCIA SIGA ESTAS PRECAUCIONES BASICAS PARA REDUCIR EL
Download Pdf Manuals
Related Search