D GB NL E
Contents
1. Montaje Indicaci n de seguridad No est permitido el uso de cables de cone xi n que no est n admitidos por Merten El uso de cables no admitidos puede repercutir negativamente en la seguridad el ctrica y en la funcionalidad del sistema Montar a presi n en carril omega 35 x 7 5 mm seg n DIN EN 50022 Para el servicio la entrada anal gica ne cesita una alimentaci n de tensi n 24 V externa por ej fuente de alimentaci n REG 24 V CA 1 A n de art 663629 Dicho aparato puede tambi n alimen tar de corriente los sensores conectados o la calefac ci n de los mismos o un m dulo de entrada anal gica 51 Conexi n elementos de mando figura Us alimentaci n de registradores de datos externos GND potencial de referencia para Us y entradas K1 K4 K1 K4 entradas de valores de medici n EIB borne de conexi n EIB 24 V AC tensi n de alimentaci n externa Bus de sistema conector de sistema 6 polos para 6 polos la conexi n de un m dulo de entrada anal gico de ampliaci n A tecla de programaci n B LED de programaci n C LED de estado de tres colores rojo naranja verde D registrador de datos 52 Alimentaci n de sensores conectados e Los sensores conectados pueden alimentarse de corriente por los bornes US y GND de la entrada anal gica v ase la figura e El consumo total de corriente de todos los sensores as alimen2. 2 3 Twilight The twilight sensor is equipped with a probe which is normally installed in vertical position in front of the building wall The measuring range of the sensors covers 0 255 lux For use with the analog input analog sensor interface the following parameters are recommended Parameter Setting corresponds to Measuring value for 0 of the measuring signal 0 0 lux Measuring value for 100 of the measuring signal 25500 255 lux Measuring range factor 0 01 Limit value 1 40 100 lux Hysteresis 1 10 25 lux Limit value 2 80 200 lux Hysteresis 2 10 25 lux O 2008 Merten GmbH 16 Application B007 Article 682191 2 4 Temperature The temperature sensor senses the temperature of the ambient air The measuring range of the sensor extends from 30 to 70 C For use with the analog input analog sensor interface the following parameters are recommended Parameter Setting corresponds to Measuring value for 0 of the measuring signal 3000 30 C Measuring value for 100 of the measuring 7000 70 C signal Measuring range factor 0 01 Limit value 1 30 0 C Hysteresis 1 2 2K Limit value 2 35 5 C Hysteresis 2 2 2K 2 5 Rain The rain sensor is equipped with a meandering conductor track and evaluates the conductivity of rain water For use with the analog input analog sensor interface the foll
3. Initialization status indication After switching on the device for the first time the analog input analog sensor interface starts a module scan status LED Orange on As a new device comes by default without configuration the status LED switches thereafter to Red flashing fast A connected analog input module shows that it is ready for operation by setting its own status LED to Flashing fast After downloading a project into the analog input analog sensor interface the status LED shows Green on The module switches its own status LED off O 2008 Merten GmbH 19 Application B007 Article 682191 Description Valves Remarks ___ Signal input No sensor Sensor 0 Sensor 0 Sensor 0 Sensor 4 Open circuit detection No detection continuity O open circuit 1 continuity 1 open circuit 0 Alarm analog input No transmission Transmit alarm bit Extension module This parameter determines whether a sensor and which sensor is connected to one of the inputs The format and the scaling factor of the measuring values for the sensor types can be set on a special parameter filecard On another filecard two limit values per input and the response when exceeded or underrun can be adjusted When a sensor with 4 20mA ouput is used this parameter permits reporting if the electrical connection is interrupted This is done by enabling a 1 bit communication object An alarm messag
4. If No transmission is selected the measuring value is transmitted only cyclically or after a WRITE request The parameter fixes the time after which the actual measuring value is being transmitted even if the difference with the respect to the previous value has not yet been reached In the O standard setting the measuring value is not transmitted cyclically Application B007 Article 682191 Limit value in of measuring range Limit value hysteresis Limit value LV activation External limit value object LV Format of external limit value object LV 0 100 above LV ON below LV hysteresis OFF above LV OFF below LV hysteresis ON below LV ON above LV hysteresis OFF below LV OFF above LV hysteresis ON 16 bit EIS5 8 bit EIS6 Limit value cyclical transmission 0 120 factor base 10s 0 no cyclical transmission O 2008 Merten GmbH 22 These three parameters define the thresholds which when exceeded or underrun generate the corresponding switching telegrams To make sure the thresholds can be safely execceded or underrun it is necessary to respect a reasonable safety margin from the extreme values of 0 and 100 when selecting the limit values and the hysteresis The parameter defines whether an object for external change of the limit value is to be activated The parameter enables either a 2 byte or a 1 byte object which permits
5. n IP 20 seg n DIN EN 60 529 Anchura de instalaci n 4 m dulos 70 mm Peso aprox 150 g 59 Conexiones Entradas alimentaci n de un hilo de hilo fino bornes roscados 0 5 mm2a 4 mm sin terminal de conductor 0 34 mm a 4 mm de hilo fino con terminal de conductor 0 14 mm a 2 5 mm instabus ElB M dulo de ampliaci n Entradas de sensor N mero se ales de sensores evaluables anal gicas 60 borne de conexi n y derivaci n enchufe de sistema de 6 polos 4 anal gicas 0 1VDC 0 10VDC 0 20 mA DC 4 20 mA DC impedancia medici n de tensi n aprox 18 kQ impedancia medici n de corriente aprox 100 Q Alimentaci n de sensores exteriores Us Conexi n de m dulos de ampliaci n 24 V DC m x 100 mA DC 24 V DC m x 80 mA Reservadas modificaciones t cnicas 61 Application B007 Article 682191 Application Analog input B007 Executable from mask version 7 1 Number of addresses max 200 dynamic table handling Yes k No Oo Number of assignments max 200 maximum number of 200 assignments Communication objects 50 Object no Function____ Name DPtype Format Flags 0 _ Analoginput Alarm object 1001 1bit CT Lie 13 20 Analog input External limit value 1 2 9 0xx 2 bytes Input 1 47 Ld 13 20 Analog input External limit value 1 2 5 001 1 byte Input 1 47 EP 21 24
6. A utilizar otros sensores los par metros a ajustar deben determinarse previamente Tipo Uso No de art Intensidad de luz exteriores 663593 Crep sculo exteriores 663594 Temperatura exteriores 663596 Viento exteriores 663591 Viento con la calefacci n exteriores 663592 Lluvia exteriores 663595 56 LED de estado ninguna alimentaci n de tensi n esc n de m dulos por entrada anal gica Apagado aranja con aranja destellos r pidos esc n de m dulos m dulo de ampliaci n versi n REG montaje en carril Rojo con error falta proyecto en el controlador Rojo destellos lentos error baja tensi n en el bus de ampliaci n Rojo destellos r pidos error error en la parametrizaci n 57 Verde destellos entos distribuci n de direcciones esc n de m dulos terminado proyecci n OK LED verde destellos r pidos descarga de par metros a los m dulos LED verde con esc n de m dulos terminado todo OK Destellos lentos 1 s destellos r pidos 2 s 58 Datos t cnicos Alimentaci n Tensi n de alimentaci n 24 V AC 10 Absorci n de corriente m x 250 mA Tensi n EIB 24 V DC 6 V 4 V Potencia absorbida EIB tip 150 mW Temperatura ambiente C a 45 C Temperatura de almacenamiento transporte 25 C a 70 C Humedad Ambiente almacenamiento transporte m x 93 humedad rel sin rociado Grado de protecci
7. Analog input Open circuit monitoring input 1 4 1 001 a Alarm object 1 001 3 5 3 5 EP 30 37 Extension module Limit value 1 input 1 1 001 Lk4 38 45 Extension module External limit value 1 2 9 0xx 2 bytes Input 5 8 4 5 45 Extension module External limit value 1 2 5 001 1 byte 4 5 LP 26 29 Measuring value input 5 5 001 Input 5 8 Extension module Open circuit monitoring input 5 82 5 1 001 Objects are visible only if the Alarm analog input or Alarm extension module parameter is set to Transmit alarm bit 2 Objects are visible only if open circuit monitoring is active for an input with a 4 20 mA signal F Objects can optionally transmit 8 bit values or 16 bit values depending on the setting of the Transmit format parameter Objects can optionally receive 8 bit values or 16 bit values depending on the setting of the Format of external limit value object parameter Objects are visible only if the Extension module available parameter is set to Yes O 2008 Merten GmbH 12 Application B007 Article 682191 Object description 0 25 Alarm object 1 bit object to indicate when on one of the inputs an overvoltage has been detected or when the voltage supply for external sensors has been overloaded Object value 0 no alarm Object value 1 alarm 1 Measuring value input 1 byte object or 2 byte object for outpu
8. The limit and hysteresis values indicated are to be considered as typical examples which can be easily adapted to the special situation in the building O 2008 Merten GmbH 15 Application B007 Article 682191 2 1 Wind speed For determination of the wind force the wind sensor is equipped with a vane which is heated as a protection against icing The measuring range of the sensor covers 0 40 m s For use with the analog input analog sensor interface the following parameters are recommended Parameter Setting corresponds to Measuring value for 0 of the measuring signal 0 0 m s Measuring value for 100 of the measuring signal 4000 40 m s Measuring range factor 0 01 Limit value 1 25 10 m s Hysteresis 1 8 3 2 m s Limit value 2 30 12 m s Hysteresis 2 8 3 2 m s 2 2 Brightness The brightness sensor is equipped with a probe which is normally installed in vertical position in front of the building wall The measuring range of the sensors covers 0 60 000 lux For use with the analog input analog sensor interface the following parameters are recommended Parameter Setting corresponds to Measuring value for 0 of the measuring signal 0 0 lux Measuring value for 100 of the measuring signal 6000 60000 lux Measuring range factor 10 Limit value 1 33 20000 lux Hysteresis 1 5 3000 lux Limit value 2 83 50000 lux Hysteresis 2 5 3000 lux
9. changing the limit value while in operation The parameter fixes the time after which the actual limit value is being transmitted In the 0 standard setting the limit value is not transmitted cyclically
10. the analog input module This object is activated for instance in case of an overvoltage at one of inputs or if an overload occurs at the terminal for the supply of the sensors This communication object does not permit drawing conclusions on the direct cause of the fault 3 2 Electrical connection During the installation of an analog input module the following points must be observed e Only one analog input module can be connected to the device e f defective an analog input module can be replaced by one of the same type while the system is in operation disconnect voltage supply from module After the replacement the analog input makes a reset after abt 25 s This action re initializes all inputs and outputs and resets them to their original state e Removal or addition of modules without adapting the project and subsequent downloading into the analog input is not permitted as this will result in system malfunctions e The U and GND terminals of the analog input module must not be connected to the corresponding terminals of another device e g of the analog input to prevent problems caused by ground loops e Sensors connected to the inputs of the analog input module must not get their power supply from the analog input Sensors connected to the inputs of the analog input must not get their power supply from the analog input module 4 Commissioning The analog input analog sensor interface is programmed with the help of the ETS
11. Bei Warenr cksendungen auf Grund von Beanstandungen wenden Sie sich bitte an unser Service Center Merten GmbH amp Co KG L sungen f r intelligente Ge b ude Service Center Fritz Kotz Stra e 8 Industriege biet Bomig West D 51674 Wiehl Telefon 49 2261 702 204 Telefax 49 2261 702 136 E Mail servicecenter merten de Internet www merten de V6821 581 01 07 05 Bei technischen Fragen wenden Sie sich bitte an unsere InfoLine Telefon 49 1805 212581 oder 49 800 63783640 Telefax 49 1805 212582 oder 49 800 63783630 E Mail infoline merten de kostenpflichtig fee required Analogeingang REG K 4fach Analogue input REG K 4 gang Application description attached Analoge ingang REG K 4 voudig Entrada anal gica REG K 4 gang merten 682191 ik GB 682191 682191 E 230V AC Us GND svay 24 10 24V AC System Bus 6 pol Gebrauchsanweisung 6 Operating instructions 20 Instrucciones de servicio 48 Gebruiksaanwijzing 34 Zu Ihrer Sicherheit Achtung Einbau und Montage elektrischer Ger te d rfen nur durch eine Elektrofachkraft erfol gen Dabei sind die geltenden Unfallverh tungsvorschriften zu beachten Bei Nichtbeachtung der Installationshinwei se k nnen Brand oder andere Gefahren ent stehen Die Verwendung anderer als von M
12. Transport temperatuur 25 C tot 70 C 43 44 Vochtigheid Sensoringangen Omgeving Aantal 4x analoog Opslag Transport max 93 rel vo analyseerbare geen vochtcondensatie sensorsignalen analoog 0 1 V DC 0 10 V DC Beveiligingsgraad IP 20 conform 0 20 mA DC DIN EN 60529 4 20 mA DC Inbouwbreedte 4 moduul pitches 70 mm Impedantie Gewicht ca 150g spanningsmeting ca 18 kQ Aansluitingen Impedantie stroommeting ca 100 Q Ingangen voeding schroefklemmen Voeding ext enkeldraads 0 5 mm 4mm2 Sensors Us 24 V DC max 100 mA DC fijndraads Aansluiting zonder draadhuls 0 34 mm 4 mm uitbreidingsmodules 24 V DC max 80 mA fijndraads met draadhuls 0 14 mm 2 5 mm instabus EIB aansluit en aftakklem Technische wijzigingen voorbehouden Uitbreidingsmoduul 6 pol systeemstekker 45 46 47 Indicaciones de seguridad Atenci n La instalaci n y el montaje de aparatos el c tricos solamente debe efectuar un electricis ta formado El mismo ha de observar durante los trabajos mencionados las vigen tes prescripciones preventivas de acciden tes En caso de no observar las instrucciones de instalaci n existe peligro de incendios o de otros peligros No est permitido el uso de cables de cone xi n que no est n admitidos por Merten El uso de cables no admitidos puede repercutir negativamente en la seguridad el ctrica y en la funcionalidad del sistema 48 Inf
13. ange Ein odulscan durch Analogeingang Orange blinkt schnell odulscan REG Erweiterungsmodul Rot Ein Fehler Kein Projekt im Controller Rot blinkt langsam Fehler Unterspannung an Erweiterungsbus Rot blinkt schnell Fehler Fehler in Parametrierung Gr n blinkt langsam Adressenvergabe Modulscan abgeschlossen Projektierung OK LED Gr n blinkt schnell Parameter Download in die odule LED Gr n Ein odulscan abgeschlossen alles OK Langsam blinkend 1 s Schnell blinkend 2 s Technische Daten Versorgung Versorgungsspannung 24V AC 10 Stromaufnahme max 250 mA Spannung EIB 24 V DC 6 V 4 V Leistungsaufnahme EIB typ 150 mW Umgebungstemperatur 5 C bis 45 C Lager Transporttemp 25 C bis 70 C Feuchte Umgebung Lager Transport max 93 r F keine Betauung Schutzart IP 20 nach DIN EN 60529 Einbaubreite 4TE 70mm Gewicht ca 150g 16 Anschl sse Versorgung ext Sensoren Us 24 V DC Eing nge Versorgung Schraubklemmen max 100 mA DC eindr htig 0 5 mm bis 4mm2 Anschluss Erweiterungsmodule 24 V DC feindr htig max 80 mA o Aderendh lse 0 34 mm bis 4 mm feindr htig Technische Anderungen vorbehalten m Aderendh lse 0 14 mm bis 2 5 mm instabus ElB Anschluss und Abzweigklemme Erweiterungsmodul 6 pol Systemstecker Sensoreing nge Anzahl 4x analog auswertbare Sensorsig
14. d cur rent signals Current signals 0 20 mA DC 4 20 mA DC Voltage signals 0 1 V DC 0 10 V DC e The current inputs are monitored for wire breakage i log transducers can be connected to the input With the aid of an analogue input module REG 4 gang part no 682192 up to four other analog sen sors can be connected and evaluated 22 Installation Safety warnings The use of connecting cables other than tho se approved by Merten ist not permitted and can have a negative effect on electrical safe ty and system functions Snap the device onto a 35 x 7 5 top hat rail as per DIN EN 50022 For operation the EIB weather station needs an exter nal 24 V source such as the power supply REG AC 24 V 1 A part no 663629 The latter can also supply the sensors connected or their heating or an analogue input module 23 Connection controls Fig Us power supply of external transducers GND ref potential for Us and inputs K1 K4 K1 K4 measured value inputs EIB EIB connecting terminal 24V AC external power supply voltage 6 pole system bus system connector 6 pole for the connection of an analogue input module A programming key B programming LED C status LED three colour red orange green D transducer 24 Power supply of sensors connected All sensors connected can be supplied via terminals US and GND of the analog input refe
15. e can be transmitted if the device detects a fault in one of the analog inputs or in the sensor supply When the parameter is set to Transmit alarm bit the Alarm object is activated This parameter determines whether an analog input module is used in addition In this case further parameter cards and communication objects for the four inputs of the extension module are activated Signal input No sensor Sensor 0 Sensor 0 Sensor 0 Sensor 4 Alarm extension module No transmission Transmit alarm bit O 2008 Merten GmbH 20 The parameter determines whether a sensor is connected to one of the inputs and what type of sensor The format and scaling of the measuring values for the sensor types can be adjusted on a special parameter filecard Two limit values per input can be fixed and the reactions when exceeded and when not reached be defined on another card An alarm can be transmitted if the device detects a fault in one of the four analog inputs or in the supply of the sensors If the parameter is set to Transmit alarm bit the alarm object is activated Application B007 Article 682191 16 bit ElS5 Measuring value transmission format 8 bit ElS6 The parameter defines whether the measuring values of this input are transmitted in the form of signed floating point numbers or as unsigned relative values Depending on this parameter further parameters for the adaptation and scali
16. easuring value for 100 of the measuring 10000 100 r h signal Measuring range factor 0 01 Limit value 1 40 40 r h Hysteresis 1 5 5 rh Limit value 2 70 70 r h Hysteresis 2 5 5 rh Measuring value for 0 of the measuring signal 3000 30 C Measuring value for 100 of the measuring 7000 70 C signal Measuring range factor 0 01 Limit value 1 50 20 C Hysteresis 1 2 2K Limit value 2 55 25 C Hysteresis 2 2 2K 2 7 Air pressure For an air pressure sensor with an input range of 70 000 120 000 Pa which is converted to O 10 volts the following parameters are recommended for use with the analog input analog sensor interface Parameter Setting corresponds to Measuring value for 0 of the measuring signal 7000 700 hPa Measuring value for 100 of the measuring 12000 1200 hPa signal Measuring range factor 10 Limit value 1 60 1000 hPa Hysteresis 1 2 10 hPa Limit value 2 64 1020 hPa Hysteresis 2 4 20 hPa 2008 Merten GmbH 18 Application B007 Article 682191 3 Connection of an analog input module An analog input module permits enlarging the number of analog sensors from four to eight 3 1 Settings of the analog input module The device software offers the same settings for the four channels of the analog input module as for the four inputs of the analog input A common alarm object can be activated for all inputs of
17. erten zugelassener Verbindungsleitungen ist nicht gestattet und kann die elektrische Sicherheit sowie die Funktionalit t des Systems nega tiv beeinflussen Systeminformation Dieses Ger t ist ein Produkt des instabus KNX EIB Sys tems und entspricht den KNX Richtlinien Detaillierte Fachkenntnisse durch instabus Schulungen werden zum Verst ndnis vorausgesetzt Die Funktion des Ger tes ist softwareabh ngig Detaillierte Informationen welche Software geladen werden kann und welcher Funktionsumfang sich damit ergibt sowie die Software selbst sind der Produktdatenbank des Herstellers zu entnehmen Planung Installation und Inbetriebnahme des Ger tes erfolgen mit Hilfe einer KNX zertifizierten Software Die Produktdatenbank sowie die technischen Beschreibungen finden Sie stets aktuell im Internet un ter www merten de Funktion e Der Analogeingang REG K 4fach verarbeitet Messda en von analogen Sensoren Es k nnen bis zu vier frei kombinierbare analoge Messwertaufnehmer ange schlossen werden e Der Analogeingang REG K 4fach wertet sowohl Spannungs als auch Stromsignale aus Stromsignale 0 20 mA DC 4 20 mA DC Spannungssignale 0 1 VDC 0 10 V DC e Die Stromeing nge werden auf Drahtbruch ber wacht Mit Hilfe eines Analogeingangsmoduls REG 4 fach Art Nr 682192 k nnen bis zu vier weitere analoge Sensoren angeschlossen und ausgewertet werden 7 8 Montage Anschlus
18. lues and hysteresis For each analog measuring value the analog input analog sensor interface has two limit values which can be preset on the parameter filecard Input For each limit value there is a parametrizable hysteresis with the possibility of fixing the response when the value is exceeded or not reached Example LW 2 Hyst 2 LW2 LW 1 LW 1 Hyst 1 Limit value 2 Limit value 1 a The limit values and the hysteresis characteristics are specified as a percentage of the full measuring range When setting the limit values and the pertaining hysteresis a safety margin of about 1 from the minimum value 0 and from the maximum value 100 should be observed Or else the signals cannot underrun or exceed the respective thresholds In this case the limit value object can transmit at maximum one telegram as shown for limit value 1 2008 Merten GmbH 14 Application B007 Article 682191 1 5 External limit values If the parameter External limit value object is set to Yes the ETS shows an additional communication object that can be used for changing the preset limit value during operation The following parameter External limit value format determines whether 16 bit floating point values or 8 bit percentage values are to be transmitted to this communication object In both cases it is necessary to limit the predefined values in the devices used as limit value t
19. lution 16 bit values are perfectly suited for display purposes e g in visualization software They have a significantly higher resolution These settings are made on the Measuring value parameter filecard When 8 bit values are used the following parameters are available Measuring value for 0 of measuring signal and Measuring value for 100 of measuring signal If the measuring values are to be transmitted as 8 bit values an ouput value between 0 and 255 can be selected for the minimimum and the maximum value of the analog input range respectively The minimum output value must be less than the maximum output value O 2008 Merten GmbH 13 Application B007 Article 682191 1 3 Transmission criteria The values measured can be transmitted automatically after a value has changed or after a certain period has elapsed since the last telegram To prevent unnecessary loading of the bus the parameter Transmit measured value after a change by can be used to define how big the change must be for a telegram to be transmitted The selection offered is 0 5 1 3 10 and no transmission If the measured values are to be transmitted cyclically the cycle time is preset with the parameter Cyclical transmission factor In conjunction with the fixed base of 10 seconds factors from O to 255 permit the selection of cycling times up to 42 5 minutes Factor O means no cyclical transmission of measured values 1 4 Limit va
20. mm to 2 5 mm connecting and branch terminal 6 pole system connector 4x analog 0 1VDC 0 10 VDC 0 20mA DC 4 20mA DC 31 Voltage measurement impedance Current measurement impedance External sensor power supply Us Extension module connection approx 18 kQ approx 100 Q 24 V DC 100 mA max 24 V DC 80 mA max Subject to technical modifications 32 33 Veiligheidsinstructies Attentie Inbouw en montage van elektrische appara ten mogen uitsluitend door een landelijk er kend installatiebedrijf worden uitgevoerd Daarbij de geldende ongevallenpreventie voorschriften naleven Bij veronachtzaming van de installatie in structies kunnen brand of andere gevaren optreden Het gebruik van andere dan de door Merten goedgekeurde verbindingsleidingen is ver boden en kan de elektrische veiligheid als mede de functionaliteit van het systeem negatief be nvloeden 34 Systeeminformatie Dit apparaat is een product van het instabus KNX ElB systeem en voldoet aan de KNX richtlijnen Voor een goed begrip is gedetailleerde vakkennis door instabus scholing een eerste vereiste De werking van het ap paraat is van de gebruikte software afhankelijk Ge detailleerde informatie over de software die kan worden geladen en de functies die hiermee mogelijk zijn alsmede informatie over de software zelf vindt u in de productdatabase van de fabrikan
21. nale analog 0 1VDC 0 10 V DC 0 20 mA DC 4 20 mA DC Impedanz Spannungsmessung ca 18kQ Impedanz Strommessung ca 100 Q 17 18 Safety warnings i Attention Electrical equipment must be installed and fitted by qualified electricians only and in fi strict observance of the relevant accident prevention regulations Failure to observe any of the installation in structions may result in fire and other ha zards The use of connecting cables other than tho se approved by Merten is not permitted and can have a negative effect on electrical safe ty and system functions 19 20 System information Function This device is a product of the instabus KNX EIB sys e The analogue input processes measuring data from tem and complies with KNX directives Detailed techni analog sensors Up to four freely programmable ana cal knowledge obtained in instabus training courses is a prerequisite to proper understanding The functionality of this device depends upon the soft ware Detailed information on loadable software and at tainable functionality as well as the software itself can be obtained from the manufacturer s product database Planning installation and commissioning of the unit is effected by means of KNX certified software An updated version of the product database and the technical descriptions are available in the Internet at www merten de 21 e The analogue input evaluates both voltage an
22. nd gezet 40 e Verwijdering of toevoeging van modules zonder aan passing van de configuratie en aansluitend downloa den naar het analoge ingang is niet toegestaan Aansluitbare sensors Bij gebruik van de volgende meetwaarde opnemers kan omdat dit functiestoringen in het systeem veroor een softwarematige voorinstelling worden gehanteerd zaakt Bij gebruikvan andere sensors moeten de in te stellen parameters van tevoren bepaald worden Meting Plaats Art nr i Helderheid buiten 663593 Schemering buiten 663594 Temperatuur buiten 663596 Wind buiten 663591 Wind met het verwarmen buiten 663592 Regen buiten 663595 41 42 Status LED LED groen 2 knippert snel Parameters worden downgeload Uit geen voedingsspanning naar de miodules Oranje Aan oduulscan door analoge ingang LED groen Aan Moduulscan voltooid alles OK Oranje knippert A snel oduulscan Langzaam knipperend 1 s Snel knipperend 2 s DRA uitbreidingsmoduul Technische gegevens Rood Aan Fout Geen project in controller Rood knippert Voeding langzaam Fout Onderspanning op Voedingsspanning 24 V AC 10 uitbreidingsbus Stroomopname max 250 mA Rood knippert snel Fout Fout in parametrisering Spanning EIB 24 V DC 6 V 4 V Groen knippert Vermogensopname EIB typ 150 mW langzaam Adrestoewijzing moduulscan Omgevingstemperatuur 5 C tot 45 C voltooid configuratie OK Opslag
23. ng of measuring values are shown Measuring value format 16 bit value 0 32767 Measuring value for 0 of measuring signal Measuring value for 100 of measuring signal Measuring range scaling factor Base value 0 of measuring value Base value 100 of measuring value event of a change by Measuring value cyclical transmission factor base 10s 0 no cyclical transmission O 2008 Merten GmbH 32768 32768 1000 32767 21 With the three parameters Measuring value for 0 Measuring value for 100 and Factor of measuring range the analog input analog sensor interface can adapt itself to the actual measuring range of the sensor used To achieve a high resolution the two base values should be selected in such a way that a good coverage of the measuring range of the sensor is obtained with a scaling factor as low as posssible With these two parameters the analog input analog sensor interface can convert the analog input signal to value range of the 1 byte communication object The parameter defines the percentage of change required with respect to the previous object value for the new value to be transmitted In a sensor with a measuring range extending from 0 10V a measuring value difference of 3 corresponds to 0 3V When the last telegram had a value of 4V a new telegram will be transmitted when the actual measuring value is below 3 7V or above 4 3V
24. ng van uitbreidings nr 663629 Deze kan ook de aangesloten sensors of moduul met analoge ingang hun verwarming of een analoge ingangsmoduul voe den A Programmeertoets B ProgrammeerLED C Status LED driekleurig rood oranje groen D Meetwaardeopnemer 37 38 Voeding van aangesloten sensors Aangesloten sensors kunnen via de klemmen US en GND van het analoge ingang gevoed worden zie afbeelding De totale stroomopname van alle hierlangs gevoede sensors mag 100 mA niet overschrijden De klemmen US en GND zijn dubbel geinstalleerd en intern verbonden Bij kortsluiting tussen US en GND wordt de span ning afgeschakeld Aangesloten kunnen ook extern gevoed worden b v wanneer hun stroomopname 100 mA overschrijdt Aansluiting op de sensoringangen geschiedt dan tus sen de klemmen K1 K4 en GND 39 Installatie van een uitbreidingsmoduul Bij het installeren van een uitbreidingsmoduul de vol gende basisregels in acht nemen e Er kan een analoge ingangsmoduul met analoge in gang worden aangesloten e Vervanging van een uitbreidingsmoduul door een mo duul van hetzelfde type b v bij een defect kan tij dens bedrijf geschieden moduul spanningvrij schakelen Na vervanging voert het analoge ingang na ca 25 s een reset uit Daardoor woorden alle in en uitgangen van het analoge ingang en de aangesloten modules opnieuw ge nitialiseerd en in de oorspronke lijke sta
25. orgt werden z B wenn deren Stromaufnahme 100 mA bersteigt Der Anschluss an die Sensoreing n ge erfolgt dann zwischen den Klemmen K1 K4 und GND Installation eines Erweiterungsmoduls Bei der Installation von Erweiterungsmodulen sind fol gende Grundregeln zu beachten e Es kann ein Analogeingangsmodul angeschlossen werden Der Tausch eines Analogeingangsmoduls gegen ei nes vom selben Typ z B bei einem Defekt kann im laufenden Betrieb erfolgen Modul spannungsfrei schalten Nach dem Tausch f hrt der Analogeingang REG K 4fach nach ca 25 s einen Reset durch Da durch werden alle Ein und Ausg nge des Analogein gangs REG K 4fach und der angeschlossenen Module neu initialisiert und in den Ursprungszustand versetzt Das Entfernen oder Hinzuf gen von Modulen ohne Anpassung der Projektierung und anschlie endes Herunterladen in den Analogeingang REG K 4fach ist nicht zul ssig da es zu Fehlfunktionen des Systems f hrt Anschlie bare Sensoren Bei Verwendung der nachfolgenden Messwertaufneh mer kann in der Software auf eine Voreinstellung zu r ckgegriffen werden Bei Verwendung anderer Sensoren m ssen die einzustellenden Parameter zuvor ermittelt werden Art Einsatz Art Nr Helligkeit Au en 663593 D mmerung Au en 663594 Temperatur Au en 663596 Wind Au en 663591 Wind mit Heizung Au en 663592 Regen Au en 663595 14 Status LED Aus keine Spannungsversorgung Or
26. ormaci n de sistema El equipo presente es un producto del sistema instabus KNX EIB y cumple las directivas KNX Para poder com prender el sistema se presuponen conocimientos espe ciales detallados adquiridos en medidas de capacitaci n instabus El funcionamiento del aparato depende del software Consulte la base de datos de productos del fabricante para recibir informaci n detallada de qu software pue de cargarse y cu l ser el funcionamiento que se puede lograr por tal software as como para recibir el software mismo La planificaci n la instalaci n y la puesta en funciona miento del aparato se llevan a cabo con la ayuda de un software KNX certificado La base de datos de productos as como las descripcio nes t cnicas m s actuales se encuentran en internet en www merten de 49 Funcionamiento e La entrada anal gica procesa datos de medici n de sensores anal gicos Pueden conectarse hasta un m ximo de cuatro registradores anal gicos de datos libremente configurables e La entrada anal gica puede evaluar tanto se ales de tensi n como se ales de corriente se ales de corriente 0 20 mA DC 4 20 mA DC se ales de tensi n 0 1 VDC 0 10 V DC e Se vigilan las entradas de corriente con respecto a la rotura de conductores e Por medio de un m dulo de entrada anal gica REG 4 gang n de art 682192 pueden conectarse y evaluar se hasta un m ximo de cuatro sensores anal gicos m s 50
27. owing parameters are recommended Parameter Setting corresponds to Measuring value for 0 of the measuring signal O Measuring value for 100 of the measuring 1000 signal Measuring range factor 0 01 Limit value 1 60 Regen Hysteresis 1 20 Kein Regen Limit value 2 Hysteresis 2 Contrary to the other weather sensors the rain detector does not supply analog measuring values but toggles between 0 volt and 10 volts so that displaying an analog value makes no sense For this reason the object Measuring value should not transmit neither in case of a change at the input nor cyclically The settings for 0 of the measuring range 100 of the measuring range and the measuring range factor are necessary for the limit value detection to function properly The suggested parameters for the limit value ensure that the switching threshold is always safely detected O 2008 Merten GmbH Application B007 Article 682191 2 6 Humidity The humidity sensor senses the relative humidity of the air and the room temperature Both measuring values are made available in the form of analog voltages The measuring ranges of the sensor extend from 0 to 100 of relative humidity and from 30 to 70 C For use with the analog input analog sensor interface the following parameters are recommended Parameter Setting corresponds to Measuring value for 0 of the measuring signal O 0 r h M
28. r to Fig The total current consumption of all sensors supplied this way must not exceed 100 mA Terminals US and GND are provided in duplicate and are internally interconnected In the event of a short circuit between US and GND the voltage will be switched off Sensors connected can also be supplied externally e g if their current consumption exceeds 100 mA In such case connection to the sensor inputs must be made between terminals K1 K4 and GND Installing an extension module Please observe the following basic rules when installing an extension module e An analogue input module can be connected e Replacement of an analogue input module if defecti ve by one of the same type can be changed during operation for this purpose disconnect the module rom the power supply After replacement the ana og input will reset after approx 25 s This will re ini ialize all inputs and outputs of the analog input and of he modules connected and reset them to their origi nal state e Removing or adding modules without adapting their configuration and subsequent downloading into the analog input is not allowed as this will result in sys em malfunctioning 25 26 Sensors suitable for connection Status LED For any of the following transducers the software pro OFF no power supply vides preset values If other sensors are used the para Orange ON module scan via analog input meters to be
29. ransmitters in such a way that in consideration of the hysteresis a corresponding safety margin is always ensured An external value overwrites the internal value Only after a new download of the project will the internal value be reactivated A readout of the object values yields correct results only after data have been written into the objects at least once via the bus after a reset 1 6 Alarm in case of overvoltage or overload A common alarm object can be activated for the four inputs of the analog input analog sensor interface in case of an overvoltage at an input or if an overload occurs at the terminal for the supply of the sensors This communication object does not permit drawing conclusions on the direct cause of the fault If the analog input analog sensor interface is connected to an analog input module a separate alarm object is available for this extension module 2 Connection of analog weather sensors The analog input analog sensor interface can also be connected to weather sensors sensing each a separate physical quantitiy For these analog weather sensors the following data point types of the communication objects are defined in the KNX standard Sensor Unit Data point type Brightness lux 9 004 Twilight lux 9 004 Wind m s 9 005 Temperature C 9 001 Humidity r h 9 007 Air pressure Pa 9 006 The parameter settings described in the following sections permit a simple adaptation to the respective measuring ranges
30. s Bedienelemente Bild Achtung il Us Versorgung externer Die Verwendung anderer als von Merten zu Messwertaufnehmer gelassener Verbindungsleitungen ist nicht GND Bezugspotential fur Us und gestattet und kann die elektrische Sicherheit Eing nge K1 K4 sowie die Funktionalit t des Systems nega K1 K4 Messwerteing nge tiv beeinflussen Aufschnappen auf Hutprofilschiene 35 x 7 5 mm nach DIN EN 50022 Der Analogeingang REG K 4fach ben tigt zum Betrieb eine externe 24 V Spannungsversor gung z B Spannungsversorgung REG AC 24 V 1 A Art Nr 663629 Diese kann auch die angeschlossenen Sensoren oder deren Heizung oder ein Analogein gangsmodul versorgen EIB EIB Anschlussklemme 24 V AC externe Versorgungsspannung System Bus Systemverbinder 6 polig zum 6 polig Anschluss eines Analogeingang Erweiterungsmoduls A Programmier Taste B ProgrammierLED C Status LED dreifarbig rot orange grtin D Messwertaufnehmer 10 Versorgung angeschlossener Sensoren Angeschlossene Sensoren k nnen ber die Klem men US und GND des Analogeingangs versorgt werden siehe Bild Die Gesamtstromaufnahme aller hier ber versorgten Sensoren darf 100 mA nicht berschreiten Die Klemmen US und GND sind doppelt vorhanden und jeweils intern miteinander verbunden Bei Kurzschluss zwischen US und GND wird die Spannung abgeschaltet Angeschlossene Sensoren k nnen auch fremd ver s
31. set must be determined beforehand Orange quickly i blinking series mounting unit REG Type Use Part no extension module scan Brightness outdoor 663593 Red ON error no configuration in Twilight outdoor 663594 controller Temperature outdoor 663596 Red slowly blinking error undervoltage on Wind outdoor 663591 extension bus Wind with heating outdoor 663592 Red quickly Rain outdoor 663595 blinking error wrong parameterization Green slowly blinking address assignment module scan completed configuration OK 27 28 Green quickly blinking parameter download into modules Green ON module scan completed everything OK Slowly blinking 1 s quickly blinking 2 s 29 Specifications Power supply Supply voltage Current consumption EIB voltage EIB power consumption Ambient temperature Storage transport temperature Humidity Ambient storage transport Protective system Installation width Weight 30 24 VAC 10 250 mA max 24 VDC 6 V 4 V 150 mW typ 5 C to 45 C 25 C to 70 C 93 RH max no condensation IP 20 as per DIN EN 60529 4 pitch 70 mm approx 150 g Connections Inputs power supply single wire stranded wire without ferrule stranded wire with ferrule instabus EIB Extension module Sensor inputs Number Evaluable sensor signals analog screw terminals 0 5 mm to 4 mm 0 34 mm to 4 mm 0 14
32. t Planning installa tie en inbedrijfstelling van het apparaat geschieden met behulp van door de KNX gecertificeerde software De productdatabase en de technische beschrijvingen vindt u steeds actueel op internet onder www merten de Functie e De analoge ingang verwerkt meetgegevens van ana oge sensors Er kunnen maximaal vier vrij combi neerbare analoge meetwaardeopnemers worden aangesloten e De analoge ingang analyseert zowel spannings als stroomsignalen Stroomsignalen 0 20 mMADC 4 20 mA DC Spanningssignalen 0 1 VDC 0 0 10 V DC e De stroomingangen worden op draadbreuk bewaakt Met behulp van een analoge ingangsmoduul REG 4 vouding art nr 682192 kunnen maximaal vier extra analoge sensors aangesloten en geanalyseerd wor den 35 36 Montage Aansluiting bedieningselementen Veiligheidsinstructie afbeelding O Het gebruik van andere dan de door Merten Us Voeding van externe goedgekeurde verbindingsleidingen is ver meetwaardeopnemers boden en kan de elektrische veiligheid als GND Referentiepotentiaal voor Us en mede de functionaliteit van het systeem ingangen K1 K4 negatief be nvloeden K1 K4 Meetwaarde ingangen Vastklikken op DIN rail 35 x 75 mm conform DIN EIB ElB aansluitklem EN 50022 24V AC externe voedingsspanning Het EIB weerstation werkt op een externe 24 V voe Systeem bus Systeemconnector 6 polig voor ding b v spanningsverzorging REG AC 24 V 1 A art 6 polig aansluiti
33. t of current measuring 26 value 4 29 Ds 12 Limit value 1 bit object to Indicate when the limit values are exceeded or 30 37 underrun 20 External limit value 1 byte or 2 byte objects for limit value correction by other bus 45 devices e g touch sensor as value transmitter visualization These values overwrite the parameterized values 25 Open circuit monitoring 1 bit object for reporting whether a fault has occurred in the 49 electrical connection of a sensor with 4 20 mA signal The value of the object for open circuit monitoring is presettable 1 Functional Description 1 1 Measuring value settings Among the most important settings is the decision whether the measuring values are to be transmitted as 8 bit or as 16 bit values The choice is basically dependent on the other devices working with the data 8 bit values can be processed by many devices although with limited resolution 16 bit values are perfectly suited for display purposes e g in visualization software They have a significantly higher resolution These settings are made on the Measuring value parameter filecard 1 2 Measuring value settings Among the most important settings is the decision whether the measuring values are to be transmitted as 8 bit or as 16 bit values The choice is basically dependent on the other devices working with the data 8 bit values can be processed by many devices although with limited reso
34. tados de corriente no debe sobrepasar los 100 mA e Los bornes US y GND hay en versi n doble est n interconectados internamente entre s e En caso de cortocircuito entre US y GND se desconecta la tensi n e Los sensores conectados tambi n pueden alimentar se de corriente de fuentes externas por ej si la po tencia absorbida sobrepase los 100 mA La conexi n a las entradas de los sensores entonces se efect a en los bornes K1 K4 y GND 53 Instalaci n de un m dulo de ampliaci n Deben observarse las reglas b sicas siguientes al insta lar el m dulo de ampliaci n e Puede conectarse un m dulo de entrada anal gica e La sustituci n de un m dulo de ampliaci n por un m dulo del mismo tipo por ej en caso de un defec to se puede realizar durante el servicio activo desconectar el m dulo de la tensi n Realizada la sustituci n la estaci n meteorol gica efect a un re set despu s de unos 25 s As se inicializan nueva mente todas las entradas y salidas de la estaci n meteorol gica y de los m dulos conectados y las po nen en el estado inicial 54 e No est admitido quitar o a adir m dulos sin adaptar la proyecci n y la descarga siguiente a la estaci n meteorol gica puesto que eso conduce a funciones err neas del sistema 55 Sensores conectables Al utilizar los registradores de datos se puede valerse en el software de valores previamente determinados
Download Pdf Manuals
Related Search