Home
VLF515 Instruction Manual
Contents
1. CAUTION Avoid potential personal injury or property damage For concrete applications the arm assembly E must remain centered the wall plate KE E 2 Lock the arm assembly KE onto the wall plate EJ by sliding the lock lever Oro the lock position NOTE For wood stud applications the arm assembly be slid anywhere along the wall plate EJ for optimal positioning of your TV A CAUTION Avoid potential personal injury or property damage Always make sure your arm assembly E is in the locked position so the TV is securely fastened to the wall plate KT 3 2 Hang TV onto Arm Assembly 2 HEAVY You may need assistance with this step 1 Position the arm assembly KE so the elbow is pressed against the wall 2 the TV onto the arm assembly KE by first hooking the top support then pressing the bottom of the TV into the arm assembly KE until the lock catches 3 Tolockthe TV in place use your hand to tighten the lock knob 9 on the vertical TV bracket CAUTION Avoid potential personal injury or property damage Always make sure the lock knob 9 is tightened so the TV is securely fastened to the arm assembly KE Manage Cables Route your TV cables along the arm assembly KE and press into the channels in the arm as shown Cables 22 LEVEL TILT Loosen the two le
2. 8 Install the four lag bolts Firmly tighten all four lag bolts D until they are pulled flush against the wall plate E NOTE Hold the wall plate place when tightening the first lag bolt D keep the plate from shifting out of place CAUTION Avoid potential personal injury or property damage All four lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate E Ensure the wall plate is securely fastened to the wall before continuing on to the next step 9 Slide the covers O closed on wall plate KT Go to STEP 3 on PAGE 19 STEP2B Solid Concrete or Concrete Block Option CAUTION Avoid potential personal injuries and property damage Mount the wall plate KE directly onto the concrete surface Minimum solid concrete thickness 8 in 203 mm Minimum concrete block size 8 x 8 x 16 in 203 x 203 x 406 mm Minimum horizontal space between fasteners 24 in 610 mm e For concrete applications arm KE STEP 3 must remain centered in wall plate KE Keep this in mind when selecting the wall plate location 1 Position the wall plate template the wall at your desired height Level the wall plate template and mark the hole locations NOTE For assistance in determining wall plate location see Height Finder at sanus com 2 Drill four pilot holes using a 3 8 in 10 mm diameter drill bit O IMPORTANT Pilot holes must be drilled to a depth of 3 in 75 mm Never
3. extends from 3 5 in 92 mm to 15 in 381 mm Level adjustments create a worry free installation Mounting arm adjusts within the wall plate for optimal positioning Ah CAUTION Avoid potential personal injury or property damage For concrete applications the arm assembly KE must remain centered in the wall plate KE Fully articulating arm with three pivot points creates optimal viewing position TV tilts up or down for the perfect viewing angle Locking mechanisms for added security in mm TV INTERFACE 3 D VLF515 m am Sooos i e _ 5 59 pr A UN UE WALL PLATE TOP VIEW EXTENDED 292 742 FULLY ASSEMBLED MOUNT SIDE VIEW RETRACTED 29 30 Para Espa ol ver p gina 32 31 ESPANOL INSTRUCCIONES DE SEGURIDAD IMPORTANTES CONS RVELAS LEA TODO EL MANUAL ANTES DE UTILIZAR ESTE PRODUCTO Antes de comenzar verifiquemos que este soporte sea el ideal para sus necesidades 1 Su televisor pesa m s de 56 7 kg 125 Ib incluidos los accesorios No Perfecto 56 7 kg 125 Ib Si Este soporte NO es compatible Visite MountFinder Sanus com o llame al 1 800 359 5520 Reino Unido 0800 056 2853 para encontrar un soporte compatible De qu est Tabiques Hormig n s lido 2 Roch
4. hormig n siga el PASO 2B en la P GINA 16 Piezas y elementos de sujeci n para el PASO 2 A ADVERTENCIA Este producto contiene piezas peque as que si fuesen tragadas podr an producir asfixia Antes de iniciar el ensamblaje compruebe que todas las piezas est n incluidas y en buenas condiciones Si faltan piezas o alguna est da ada no devuelva el art culo al distribuidor p ngase en contacto con el servicio de atenci n al cliente Nunca utilice piezas deterioradas A ADVERTENCIA Este producto contiene un im n Si utiliza un dispositivo m dico implantado como un marcapasos o un desfibrilador autom tico implantable DAI los campos magn ticos pueden afectar el funcionamiento de esos dispositivos y causar heridas de gravedad o la muerte Si tiene un dispositivo m dico implantado mantenga una distancia de al menos 13 cm 5 pulgadas entre su dispositivo y el im n Consulte a su m dico antes de utilizar este producto 3 NOTA No todos los accesorios incluidos deber n utilizarse uyy Wi Opci n para montantes de madera 34 PRECAUCI N Evite lesiones y da os materiales e Elyeso que recubre la pared no debe exceder los 16 mm 5 8 e m nimo del montante de madera com n 51 mm x 102 mm 2 x 4 nominal 38 mm x 89 mm 11 2 x 31 2 e Espacio horizontal m nimo entre los elementos de sujeci n 406 mm 16 pulgadas e Se deben verificar las partes centrales de los pernos no todas las
5. inserts on the back of your TV to determine which screw diameter 4 5 M6 or M8 to use M4 M5 6 8 2000 Ah CAUTION Verify adequate thread engagment of the screw spacer combination on your TV Too short will not hold the TV and too long will damage the TV Too Long Too Short Correct Spacers and screws are supplied to install your TV bracket Determine your preference for spacer configuration when attaching your TV bracket TV Bracket Mount the spacers O under the TV bracketto create extra space needed for irregular shape TV backs or large cables Mountthe spacers above the TV bracket so the TV bracket sits close to the TV surface for flat back panels Flat Back Inset Holes Cables Round Back 1 3 Attach TV Brackets 1 Slide TV bracket plate E into upper TV bracket XX and loosely install using two thumb screws 2 Slide the upper lower brackets onto the ends of the vertical TV bracket EZ 3 Position the TV bracket assembly over your TV hole pattern center horizontally and loosely install using the spacer TV screw and washer combination a or b you selected for your TV 22 If your TV included inset spacers or wall mount adapters see Troubleshooting on PAGES 26 27 Spacer screw and washer Standard configurations are shown For special applicat
6. there are any special requirements for mounting your TV If you do not understand these instructions or have doubts about the safety of the installation assembly or use of this product contact Customer Service at 1 800 359 5520 UK 0800 056 2853 CAUTION Avoid potential personal injuries and property damage This product is designed for use in wood stud solid concrete and concrete block walls DO NOT install into drywall alone The wall must be capable of supporting five times the weight of the TV and mount combined Do not use this product for any purpose not explicitly specified by manufacturer Manufacturer is not responsible for damage or injury caused by incorrect assembly or use STEP 1 Attach Bracket to TV Parts and Hardware for STEP 1 Ah WARNING This product contains small items that could be a choking hazard if swallowed Before starting assembly verify all parts are included and undamaged If any parts are missing or damaged do not return the damaged item to your dealer contact Customer Service Never use damaged parts NOTE Not all hardware included will be used TV Screws TV Washers Vertical TV Bracket C_ _ inn MOINS M4x35 mm C ON M5x35 mm O 4 Spacers M6x35 mm TV Bracket Plate r3 E 138 Y M8x45 mm 1 1 Select TV Screws 1 2 Spacers Hand thread screws into the threaded
7. DEBEN ESTAR apretados firmemente para evitar que la placa mural se desplace Aseg rese de que la placa mural est fijada con seguridad a la pared antes de proceder con el siguiente paso Deslice las cubiertas O cerradas sobre la placa mural E Contin e con el PASO 3 en la P GINA 19 35 PASO 2B Opci n para hormig n s lido o bloques de cemento 36 PRECAUCI N Evite lesiones y da os materiales e Instale la placa mural directamente sobre la superficie de hormig n e Espesor m nimo del hormig n 203 mm 8 e Tama o m nimo del bloque de cemento 203 x 203 x 406 mm 8 x 8 x 16 e Espacio horizontal m nimo entre los elementos de sujeci n 610 mm 24 e Paraaplicaciones del hormig n brazo KE PASO 3 debe permanecer en la posici n central en la placa mural Tenga esto cuenta a la hora de seleccionar la ubicaci n de la placa mural 1 Coloque la plantilla de la placa mural Men la pared a la altura que desee Nivele la plantilla de la placa mural y marque la ubicaci n de los orificios amp NOTA Si necesita ayuda para determinar la ubicaci n de la placa mural utilice la herramienta HeightFinder disponible en sanus com 2 Haga los cuatro orificios gu a con una mecha de 10 mm 3 8 de di metro Q IMPORTANTE Los orificios gu a deben realizarse hasta una profundidad de 75 mm 3 Nunca perfore el cemento que une los bloques 3 Retire la plantilla de la placa mural e inserte cu
8. THANK YOU FOR CHOOSING SANUS THE 1 TV MOUNT BRAND IN THE US VLF515 Instruction Manual 2 SANUS MAGN ETIC STUD FINDER Designed to find your studs and make life easier included in hardware kit magnet probing pin level locates screws in drywall helps find the edges of attaches to your wall plate to show exactly where your stud within the wall for hands free leveling your studs are Pull apartthe SANUS Magnetic Stud Finder to expose the probing pin within Starting about 1 2 inch away from the first pencil mark insert the probing pin into the wall every 1 inch until it inserts completely into the wall Once that happens you know you ve found one edge of your stud Repeat this process till you have found the stud edges and center of the stud Holding it vertically lightly move the SANUS Magnetic Stud Finder up and down while sliding across your wall The magnet within will be attracted to the screws in the stud Once the magnet has landed on a screw place a pencil mark on the wall directly below the magnet You can verify this is a stud by moving the Magnetic Stud Finder up or down to find a second or third screw within the wall WARNING This product contains a magnet If an implanted medical device such as a pacemaker or implantable cardioverter defibrillator ICD is in use magnetic fields may affectthe operation of those devices resulting in serious injury or death If you have an implanted medical devic
9. UTUBE COM SANUSSYSTEMS Learn ways to getthe most out of your space Find product updates and more Learn installation tips tricks and household know hows View step by step product videos to ease your install experiences Find the latest news stories about your favorite SANUS products REGISTER YOUR NEW SANUS PRODUCT By registering you ll be entered to win and will receive the latest product updates design tips and other ways to enhance your life in your home Visit SANUS com register to complete your registration and start enjoying all of the benefits SANUS has to offer Leave a product review and X cox x let us know how your install went If you ever have questions about your SANUS product give us a call at 1 800 359 5520 We re ready to help Monthly prize rules and restrictions apply Visit SANUS com for more info 800 359 5520 UK 0800 056 2853 info sanus com sanus com 02014 Milestone AV Technologies All rights reserved SANUS is a division of Milestone All other brand names or marks are used for identification purposes and are trademarks of their respective owners SANUS 6436 City West Parkway Eden Prairie MN 55344 USA 6901 002411 00
10. a su e yeso con o bloques de No est d montantes de cemento seguro pared madera Llame al 1 800 359 5520 Perfecto Reino Unido 0800 056 2853 3 Tiene E 6 D todas las herramientas 5 5 mm 10 mm h 51991 13 mm necesarias M Hen s 1 27 Destornillador Cinta m trica Broca Broca Taladro el ctrico Martillo Llave de tubo 4 Listo para Lea estas instrucciones en su totalidad para estar seguro de sentirse c modo con este f cil proceso de instalaci n Consulte comenzar tambi n el manual del usuario de su televisor para ver si existe alg n requisito especial para instalar su televisor en la pared Si no entiende las instrucciones o si tiene dudas acerca de la seguridad de la instalaci n del ensamblado o del uso del producto p ngase en contacto con el servicio de atenci n al cliente al 1 800 359 5520 Reino Unido 0800 056 2853 APRECAUCI N Evite posibles lesiones personales y da os materiales e Este producto est dise ado para usarse nicamente en aplicaciones con montantes de madera hormig n y bloques de hormig n NO lo instale en tabiques nicamente de yeso e La pared debe soportar cinco veces el peso del televisor y del soporte juntos e Noutilice este producto para ning n otro prop sito que no sea el expl citamente especificado por el fabricante 32 e Elfabricante no se responsabiliza por ning n da o o lesi n resultante del montaje incorrecto o de uso indebido ESPA OL PASO 1 Colocar las placas de suje
11. ar hasta que escuche el clic que indica que qued en su lugar 44 PRECAUCI N Evite el riesgo de lesiones y da os materiales Para aplicaciones del hormig n brazo KE Paso 3 debe permanecer en la posici n central en la placa mural NOTA Para aplicaciones de madera el m dulo del brazo KE puede deslizarse a lo largo de la placa mural para un posicionamiento ptimo del televisor Bloquee el m dulo del brazo EE sobre la placa mural para ello deslice la palanca de bloqueo O la posici n de bloqueo PRECAUCI N Evite el riesgo de lesiones y da os materiales Siempre aseg rese de que el brazo est en la posici n bloqueada para que el televisor quede bien sujeto a la placa mural 3 2 Colgar el televisor en el m dulo del brazo Coloque el m dulo del brazo de modo que el codo quede presionado contra el muro Cuelgue el televisor en el m dulo del brazo EE para ello primero enganche el soporte superior luego presione la parte inferior del televisor hacia el modulo del brazo hasta que las presillas de queden bloqueadas Para bloquear el televisor en su lugar use su mano para ajustar la perilla de bloqueo 9 sobre la placa de sujeci n vertical del televisor 44 PRECAUCI N Evite el riesgo de lesiones y da os materiales Siempre aseg rese de que el bot n de bloqueo 9 se apretado abrochado para que el televisor est firmemente sujeto al conjunto del brazo 37 Organizar los cable
12. atro anclajes B PRECAUCI N Cerci rese de que los anclajes 18 queden nivelados respecto de la superficie de hormig n 4 Deslice las cubiertas O abiertas sobre la placa mural para que los orificios de montaje queden expuestos 5 Instale los cuatro tornillos tirafondo D Apriete los cuatro tornillos tirafondo O hasta que est n nivelados en la placa mural NOTA Sostenga la placa mural su lugar mientras ajusta el primer perno O para evitar que se mueva fuera de su sitio A PRECAUCI N Evite posibles lesiones personales y da os materiales Los cuatro tornillos tirafondo O DEBEN ESTAR apretados firmemente para evitar que la placa mural se desplace Aseg rese de que la placa mural est fijada con seguridad a la pared antes de proceder con el siguiente paso 6 Deslice las cubiertas O cerradas sobre la placa mural Kf PASO 3 Fijar el televisor a la placa mural Ver p gina 19 2 ELEMENTO PESADO Es posible que necesite ayuda en este paso Piezas para el PASO 3 ADVERTENCIA Antes de iniciar el ensamblaje compruebe que esta pieza est en buenas condiciones Si est da ada no devuelva el art culo al distribuidor p ngase en contacto con el servicio de atenci n al cliente Nunca utilice piezas deterioradas 3 1 Fijar el m dulo del brazo a la placa mural 1 Cuelgue el m dulo del brazo sobre la placa mural para ello primero enganche el soporte superior luego apoye el brazo en su lug
13. bleshooting 26 For TVs that come with inset spacers or wall mount adapter rings and your installation requires Flat Back Low Profile Use your TV supplied spacers and TV Supplied TV Supplied do not use the Sanus spacers Spacer NOTE If using the M8x35 mm TV screws B you may or may not need the washers depending on length of screw engagement CAUTION Verify adequate thread engagement with the screw or screw spacer combination Too short will not hold the TV TV Supplied Spacer Too long will damage the TV TV Supplied O Spacer For TVs that come with inset spacers or wall mount adapter rings and your installation requires Rounded Back Extra Space Use the Sanus spacers TV Supplied Spacers and longer screws Do not use your TV supplied spacers amp NOTE If using the M8x45 mm TV screws 09 you may or may not need the washers depending on length of screw engagement Ah CAUTION Verify adequate thread engagement with the screw or screw spacer combination Too short will not hold the TV Too long will damage the TV 0000 27 28 ALA E TV bracket expands to fit TV hole patterns from 300 x 200 mm up to 700 x 400 mm Fully articulating arm
14. ci n en el televisor Ver p gina 5 Piezas y elementos de sujeci n para el PASO 1 ADVERTENCIA Este producto contiene piezas peque as que si fuesen tragadas podr an producir asfixia Antes de iniciar el ensamblaje compruebe que todas las piezas est n incluidas y en buenas condiciones Si faltan piezas o alguna est da ada no devuelva el art culo al distribuidor p ngase en contacto con el servicio de atenci n al cliente Nunca utilice piezas deterioradas 1 1 Seleccionar los tornillos del televisor Enrosque manualmente los tornillos en los encastres roscados del dorso del televisor a fin de determinar qu di metro de tornillos M4 M5 M6 o 8 utilizar A PRECAUCI N Verifique que la combinaci n de tornillo y separador enrosque correctamente en su televisor Si el tornillo es demasiado corto el televisor no se sostendr si es demasiado largo da ar el televisor 1 2 Separadores Los separadores y tornillos se proporcionan para instalar la placa de sujeci n de su televisor Determine cu l es su preferencia para la configuraci n de los separadores al fijar la placa de sujeci n de su televisor Instale los separadores encima de la placa de sujeci n de su televisor de modo que la placa de sujeci n quede cerca de la superficie del televisor para los paneles planos posteriores Instale los separadores O debajo de la placa de sujeci n del televisor para crear m s espacio para los televisores con forma irregular en la
15. d Sanus Magnetic Stud Finder Wall Plate Ce Wall Plate Template 5 6 in x 2 34 in Concrete Anchor Eid Wood Stud Option CAUTION Avoid potential personal injuries and property damage e Drywall covering the wall must not exceed 5 8 in 16 mm e Minimum wood stud size common 2 x4 in 51 x 102 mm mm nominal 1 x 3 in 38 x 89 mm e Minimum horizontal space between fasteners 16 in 406 mm e Stud centers mustbe verified not all walls have conventional 16 in 406 mm or 24 in 610 mm stud spacing 1 Locate a nail screw in the studs using the Sanus magnetic stud finder provided 2 Findthe edges ofthe studs using the probe of the stud finder f 3 Markthe centers of the studs with a pencil 4 Place the wall plate template PJ at your desired height and position the slotted holes over your stud center lines Level the wall plate template tape in place NOTE For assistance determining wall plate location see HeightFinder at sanus com IMPORTANT Be sure you mark and drill into the center of the stud 5 Drill the four pilot holes using a 7 32 in 5 5 mm diameter drill bit IMPORTANT Pilot holes must be drilled to a depth of 3 in 75 mm in 75 mm 6 Remove the wall plate template FJ 7 Slide the covers Oopen on the wall plate KE to expose the mounting holes
16. drill into the mortar between blocks n 3 Remove the wall plate template KE and insert four anchors Ah CAUTION Be sure the anchors are seated flush with the concrete surface 4 Slide the covers open on the wall plate KE to expose the mounting holes 5 Install the four lag bolts Firmly tighten all four lag bolts D until they are pulled flush against the wall plate E NOTE Hold the wall plate place when tightening the first lag bolt keep the plate from shifting out of place Ah CAUTION Avoid potential personal injury or property damage All four lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate KE Ensure the wall plate is securely fastened to the wall before continuing on to the next step 6 Slide the covers O closed on wall plate KT STEP 3 Attach TV to Wall Plate Part for STEP 3 3 1 Attach Arm Assembly to Wall Plate WARNING Before starting HEAVY You may need assistance with this step assembly verify this part is undamaged If damaged do not return the damaged item to your dealer entari EUSIBUTIB Senie 1 the arm assembly KE onto the wall plate KE by first hooking the top support Never use damaged parts then resting the arm assembly into place until you hear the lock click securing the arm in place Arm Assembly
17. e keep at least 13 cm 5in between your device and the magnet Please consult with your physician or medical professional prior to using this product Para Espa ol ver p gina 32 We ll Make It Stress Free If you have any questions along the way just give us a call 1 800 359 5520 UK 0800 056 2853 We re ready to help Lo haremos sin estr s Si tiene preguntas mientras realiza la instalaci n ll menos 1 800 359 5520 Reino Unido 0800 056 2853 Estamos listos para ayudarlo IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS PLEASE READ ENTIRE MANUAL PRIOR TO USE Before getting started let s make sure this mount is perfect for you 1 Does your TV weigh more than 125 Ib 56 7 kg including accessories No Perfect Yes This mountis NOT compatible Visit MountFinder Sanus com or call 1 800 359 5520 UK 0800 056 2853 to find a compatible mount 2 What is your all made of Solid concrete or w 7 concrete block Drywall with nsure wood studs U Tr ae Call Customer Service 1 800 359 5520 UK 0800 056 2853 3 Do you have all the tools 7 32 3 8 needed f 1 2 in Concrete 13 mm Screwdriver Tape Measure Drill Bit Drill Bit Electric Drill Hammer Socket Wrench 4 Ready to Please read through these instructions completely to be sure you re comfortable with this easy install process begin Also check your TV owner s manual to see if
18. el televisor ANOTA Si est usando tornillos M8 de 45 mm O es posible que necesite o no las arandelas seg n la longitud de sujeci n del tornillo PRECAUCI N Verifique el enrosque adecuado del tornillo o del conjunto tornillo separador Si es demasiado corto no sostendr el televisor Si es demasiado largo da ar el televisor 40 Descripci n Ver pagina 28 La placa de sujeci n se expande para adecuarse a televisores con patrones de orificios de 200 x 200 mm hasta 700 x 400 mm El brazo completamente articulado se extiende de 92 mm 3 5 a 381 mm 157 El brazo completamente articulado crea un movimiento de 3 puntos para alcanzar una posici n de visualizaci n ptima El ajuste del nivel crea una instalaci n sencilla Los ajustes permiten controlar o restringir el movimiento del televisor con las yemas de los dedos El brazo de montaje se puede ajustar en la placa mural para un posicionamiento ptimo A PRECAUCI N Evite el riesgo de lesiones y da os materiales Para aplicaciones del hormig n brazo PASO 3 debe permanecer en la posici n central en la placa mural E El televisor se inclina hacia arriba y hacia abajo para obtener el ngulo de visualizaci n perfecto Los mecanismos de bloqueo brindan una mayor seguridad MTS in Imm Ver p gina 29 41 42 Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to
19. ions or if you are uncertain about your hardware selection contact Customer Service at 1 800 359 5520 4 Vertically center TV bracket EJ 5 Visually line up the locator hole in the lower TV bracket with a hole in the vertical TV bracket E and install using two thumb screws Tighten the four thumb screws on the upper lower brackets 6 Tighten the four TV screws PAGE 8 on the upper lower brackets STEP 2 Attach Wall Plate to Wall For wood stud installations follow STEP 2A on PAGE 12 For concrete installations follow STEP 2B on PAGE 16 Parts and Hardware for STEP 2 Ah WARNING This product contains small items that could be a choking hazard if swallowed Before starting assembly verify all parts are included and undamaged If any parts are missing or damaged do not return the damaged item to your dealer contact Customer Service Never use damaged parts A WARNING This product contains a magnet If an implanted medical device such as a pacemaker or implantable cardioverter defibrillator ICD is in use magnetic fields may affect the operation of those devices resulting in serious injury or death If you have an implanted medical device keep at least 13 cm 5 between your device and the magnet Please consult with your physician or medical professional prior to using this product NOTE Not all hardware included will be use
20. make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations Nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subjectto change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Milestone AV Technologies y sus empresas asociadas y filiales colectivamente Milestone tienen la intenci n de que este manual sea preciso y completo Sin embargo Milestone no garantiza que la informaci n que contiene incluya todos los detalles condiciones y variaciones ni que contemple toda posible contingencia en conexi n con la instalaci n y uso de este producto La informaci n contenida en este documento es susceptible de ser modificada sin aviso ni obligaci n de ning n tipo Milestone no hace ninguna manifestaci n de garant a expl cita o impl cita respecto a la informaci n contenida este documento Milestone no asume ninguna responsabilidad por la exactitud integridad o suficiencia de la informaci n contenida en este documento FOLLOW SANUS ON YOUR FAVORITE SOCIAL NETWORKS FACEBOOK COM SANUSSYSTEMS TWITTER COM SANUSSYSTEMS YO
21. ord n de desenganche O de la placa de sujeci n vertical del televisor mientras tira de la parte inferior del televisor desde el m dulo del brazo KE 44 PRECAUCI N Evite el riesgo de lesiones y da os materiales Para que el pasador de seguridad no se rompa siempre jale y sostenga del cord n de desenganche O mientras retira el televisor de la del brazo KE 4 Levante el televisor y retirelo del m dulo del brazo KE E NOTA Para volver a colocar el televisor siga el procedimiento de los PASOS 3 y 2 en la P GINA 21 39 22 Soluci n de problemas Ver p gina 26 Para televisores que incluyen separadores insertados o aros adaptadores para soportes murales su instalaci n requiere dorso plano perfil bajo Use los separadores proporcionados con el televisor y no use los separadores Sanus ANOTA Si est usando tornillos M8 de 35 mm e es posible que necesite o no las arandelas seg n la longitud de sujeci n del tornillo PRECAUCI N Verifique el enrosque adecuado del tornillo o del conjunto tornillo separador es demasiado corto no sostendr el televisor Si es demasiado largo da ar el televisor Para televisores que incluyen separadores insertados o aros adaptadores para soportes murales su instalaci n requiere dorso redondeado espacio adicional 00000000 Use los separadores Sanus B los tornillos m s largos No use los separadores proporcionados con
22. paredes tienen una separaci n convencional de 406 mm 16 o 610 mm 24 Encuentre un clavo tornillo en los montantes con el detector magn tico de bordes de montantes Sanus O incluido Encuentre los bordes de los montantes con el detector magn tico de bordes de montantes O Marque los centros de los montantes con un l piz Coloque la plantilla de placa mural m a la altura que desee y posicione los orificios en forma de ranura sobre las l neas centrales del montante Nivele la plantilla de la placa mural fijela con cinta adhesiva en el lugar EA NOTA Si necesita ayuda para determinar la ubicaci n de la placa mural utilice la herramienta HeightFinder disponible en sanus com o IMPORTANTE Aseg rese de marcar y perforar el centro del montante Haga los cuatro orificios gu a con una mecha de 5 5 mm 7 32 de di metro Q IMPORTANTE Los orificios gu a deben realizarse hasta una profundidad de 75 mm 37 Retire la plantilla de la placa mural Deslice las cubiertas O abiertas sobre la placa mural para que los orificios de montaje queden expuestos Instale los cuatro tornillos tirafondo Apriete los cuatro tornillos tirafondo hasta que est n nivelados la placa mural NOTA Sostenga placa mural su lugar mientras ajusta el primer perno O para evitar que se mueva fuera de su sitio 44 PRECAUCI N Evite posibles lesiones personales y da os materiales Los cuatro tornillos tirafondo D
23. parte posterior o cables extensos 1 3 Fije las placas de sujeci n 1 Deslice la placa en el la placa de sujeci n superior e instale sin apretar con dos tornillos 2 Deslice las placas de sujeci n superior e inferior sobre los extremos de la placa de sujeci n vertical del televisor 3 Posicione el m dulo de la placa de sujeci n sobre el patr n de orificios del televisor c ntrelo horizontalmente y coloque sin ajustar la combinaci n de separador tornillo y arandela que seleccion para su televisor 4 Centre verticalmente la placa de sujeci n del televisor 5 Alinee visualmente los orificios O Localizador en la placa de sujeci n inferior con los orificios de la placa de sujeci n vertical del televisor e instalar usando dos tornillos Ajuste los quatro tornillos O 6 Ajuste los quatro tornillos P GINA 8 en las placas de sujeci n superior J e inferior del televisor Se ilustran las configuraciones est ndar Si desea informaci n sobre aplicaciones especiales o si tiene dudas sobre la elecci n de los elementos de fijaci n cont ctese con el servicio de atenci n al cliente 1 800 359 5520 Reino Unido 0800 056 2853 33 NOTA No todos los accesorios incluidos deber n utilizarse PASO 2 Fijar el m dulo del brazo o la placa mural a la pared Ver p gina 10 Para instalaciones sobre montantes de madera siga el PASO 2 en la P GINA 12 Para instalaciones en paredes de
24. s Ver p gina 22 Pase los cables del televisor a lo largo del m dulo del brazo Ny presi nelos sobre los canales del brazo como se muestra Aj ustes Ver pagina 23 NIVEL Afloje dos tornillos de nivel ajuste su televisor luego ajuste los dos tornillos de nivel INCLINACION El televisor debe acomodarse facilmente al moverlo y luego quedar en su lugar Si su televisor se inclina naturalmente hacia arriba o hacia abajo ajuste la perilla de tensi n de inclinaci n O con la mano NOTA Si no tiene la intenci n de ajustar la inclinaci n para los diferentes puntos de visualizaci n puede ajustar las perillas de tensi n de inclinaci n 7 para evitar movimientos indeseados 38 DESPLAZADOR LATERAL DEL TELEVISOR ELEMENTO PESADO Es posible que necesite ayuda en este paso 44 PRECAUCI N Evite el riesgo de lesiones y da os materiales NO ajuste la posici n del brazo desde la posici n central para aplicaciones del hormig n Brazo debe permanecer en la posici n central en la placa mural para todas las aplicaciones del hormig n Para aplicaciones de madera Deslice el m dulo del brazo KE junto con la placa mural KE seg n sea necesario EXTRACCI N DEL TELEVISOR ELEMENTO PESADO Es posible que necesite ayuda en este paso 1 todos los cables del televisor 2 Afloje la perilla de bloqueo Que se encuentra en la placa de sujeci n vertical del televisor 3 Tire del c
25. vel screws adjust your TV then tighten the two level screws Your TV should adjust easily when moved then stay in place Adjust the tilt tension knob by hand if your TV naturally tilts up or down amp NOTE If you do not intend to adjust the tilt for different viewing locations you can tighten the tilt tension knob Qu prevent unwanted movement i Tighten Loosen gt t 23 24 TV LATERAL SHIFT 2 HEAVY You may need assistance with this step A CAUTION Avoid potential injuries or property damage Do NOT adjust the arm position from center for concrete applications Arm KE MUST remain centered in wall plate KE for all concrete applications For wood stud applications Slide the arm assembly KE along the wall plate KE as needed REMOVING THE TV 9 HEAVY You may need assistance with this step Disconnect all cables from the TV 2 Loosenthe lock knob 9 on the vertical TV bracket 3 Pullthe release cord O on the vertical TV bracket while pulling the bottom of TV from the arm assembly KE CAUTION Avoid potential personal injury or property damage To prevent breaking the locking latch always pull and hold the release cord down while pulling the TV away from arm assembly KE 4 Liftthe TV and remove from the arm assembly KE NOTE To rehang the TV follow the procedures in STEP 3 2 on PAGE 21 E Trou
Download Pdf Manuals
Related Search
Related Contents
Portable Evaporative Air Cooler Evaporativo Portátil logiREF-VIDEO-ISP-EVK JVC GY-HM700U Copyright © All rights reserved.
Failed to retrieve file