tp-508-hub-kit-instructions 446.86KB 2014-06-18
Contents
1. Installation Instructions Item TP Hub Kit 508 1150 0800 9112 5801 Hub Kit Content Thrust Washer 41580900 Hub Bushing 41510400 15 spline Prop Nut Spacer 41510500 Flat Washer 5 CAUTION FAILURE TO FOLLOW THESE INSTRUCTIONS VOIDS THE WARRANTY Before servicing propeller be sure the engine is in A spinning propeller can be dangerous Do not approach it while the motor is operating and active It can cause serious injury or death If you have any questions please contact your Dealer or our Product Support 1 Remove fish line on shaft if any Replace your OEM thrust washer with the one included in the kit Slide with the tapered end in first to match the tapered surface of the prop shaft Caution If a thrust washer is not used severe damage could occur to propeller and or engine drive 2 Clean and grease the spline of the prop shaft Any marine grade grease is acceptable 3 Grease the surfaces of hub bushing and hub cavity and slide hub bushing into propeller housing from the front Seating the hub bushing completely to the bottom may require a few taps with a mallet 4 Slide the prop assembly from step 3 on the prop shaft 5 Slide prop nut spacer and flat washer onto the propeller assembly before prop nut 6 Tighten prop nut per your Engine Owner s Manual for proper prop nut torque 55 ft lb in most cases 7 Reinstall cotter pin and bend ends 8 Rotate propeller in ne2. incidental or indirect damages or costs caused by defects in material or workmanship Observation of a defect requires that you stop use of the product and immediately report the defect to Turning Point Propellers Inc or an authorized repair center Turning Point Propellers Inc reserves the right to repair or replace the warranted propeller and or hub with one of current production This is a Limited Warranty Turning Point Propellers Inc makes no warranty other than contained herein All obligations of Turning Point Propellers Inc are specifically set forth herein Turning Point Propellers Inc does not authorize any person or business to assume liability or contact on behalf of Turning Point Propellers Inc Any actions arising out of this warranty and the sale of this product shall be governed by Foriada law and may only be brought heard decided in Duval County Circuit Court in the State of Foriada U S A or in the United States District Court for the Northern District of Foriada Proof of purchase receipt must accompany any warranty claim Turning Point Propellers Inc Email sales TurningPointPropellers com Web www TurningPointPropellers com Phone 847 437 6800 US Patent 5 967 751 6 358 008 6 471 481 7 717 678 amp Worldwide Patented with Patents Pending All registered trademarks are the property of their respective owners Installation Instructions Item TP Hub Kit 508 1150 0800 9112 5801
3. Contenu du kit moyeu Rondelle de but e 41580900 Moyeu 41510400 15 cannelures Entretoise de friction 41510500 Rondelle plate 5 ATTENTION NE PAS SUIVRE CES INSTRUCTIONS ANNULE LA GARANTIE Avant de proc der la r vision de l h lice v rifier que le moteur soit au point mort et d connect de la borne positive de la batterie pour viter tout d marrage du moteur qui causerait de graves blessures potentiellement Une h lice qui tourne peut tre dangereuse Ne pas s en approcher pendant que le moteur tourne Cela peut provoquer de graves blessures potentiellement mortelles Si vous avez des questions contactez votre revendeur ou notre ligne d aide pour nos produits 1 Enlever la ligne de p che de l arbre s il y en a une Remplacer la rondelle de but e du constructeur par celle qui est fournie dans le kit Glisser l extr mit conique en premier pour s adapter la surface conique de l arbre d h lice Attention si on n utilise pas de rondelle but e des d g ts importants pourraient tre occasionn s l h lice et ou au syst me de propulsion 2 Nettoyer et graisser les cannelures de l arbre d h lice N importe quelle graisse marine de qualit peut tre utilis e 3 Graisser les surfaces ext rieures du moyeu et les surfaces int rieures du logement de ce dernier Glisser la bague dans le logement par l avant La placer compl tement au fond peut n cessiter quelques coups avec un mail
4. metro externo para separarlo de la tuerca de la h lice
5. let en caoutchouc Elle doit tre fleur ou l g rement encastr e dans son logement 4 Glisser le tout partir de l tape 3 sur l arbre d h lice 5 Glisser la rondelle de friction rondelle plate sur l h lice avant l crou d h lice 6 Serrer l crou d h lice selon le manuel d utilisation de votre moteur pour un serrrage correct dans la plupart des cas 55 ft lb 7 R installer la clavette et courber les extr mit s 8 Faire tourner l h lice manuellement au point mort pour s assurer qu elle tourne librement et qu elle ne frotte pas contre le carter de la bo te de vitesse Pour enlever le moyeu de son logement utiliser un jet de 91 25 4mm ou une douille pour la sortir de l extr mit de l crou de l h lice Componentes del kit de bujes Arandela Thrust 41580900 Cojinete del buje 41510400 Barril 15 Expansi n para Tuerca de H lice 41510500 Arandela Plana No 5 AVISO FALLA A SEGUIR LAS INSTRUCCIONES ANULA LA GARANTIA Antes de darle servicio a la h lice asegurese que el motor se encuentre en neutral y desconectado del polo positivo de la bater a para evitar la posibilidad de que el motor arranque y pueda causar heridas serias muerte Una h lice en movimiento puede ser peligrosa No se aproxime mientras el motor est operando y activo Puede que cause accidentes serios y hasta la muerte Si tiene preguntas dudas pongase en contacto con su Dealer local llamenos a nuestra linea de ser
6. utral by hand to make sure it rotates freely To remove hub bushing from prop housing use 1 OD rod or socket to tap out from prop nut end Periodically check prop surface for nicks or bent blade replace damaged prop immediately Check prop nut tightness to owner s manual specification Limited Warranty any claim under the warranty must be in writing Turning Point Propellers Inc warrants its propellers and hub kits against failure due to defects in materials and workmanship to the original purchaser CONSUMER USE Housings One Year from Date of Purchase HUBS Lifetime Limited Warranty COMMERCIAL USE Housings One Year from Date of Purchase Hubs One Year from Date of Purchase This warranty is not transferable to any subsequent purchaser Turning Point Propellers Inc will repair or replace any defective propeller or hub under the terms of this warranty at our Jacksonville FL facility or at our option at an authorized repair center Replacement or repair by other than Turning Point Propellers Inc or an authorized repair center relieves Turning Point Propellers Inc from the terms of this warranty This limited warranty does not include any of the following damages caused by misuse striking a foreign object corrosion cavitation electro chemical action improper installation or any modification or use in racing or any other competitive activity Turning Point Propellers Inc is not liable for consequential
7. vicio al cliente 1 Remueva hilo de pescar del eje si es necesario Reemplaze su arandela thrust de f brica OEM con la que viene incluida en este kit Deslice con el lado c nico primero para que se acomode con la superficie c nica del eje de la h lice Aviso Si no usa la arandela thrust puede causar da os severos a la h lice transmisi n del motor 2 Limpie y engrase el barril de la h lice cualquier tipo de lubricante marino es aceptable 3 Engrase las superficies externas del cojinete del buje y las superficies internas de la cavidad donde encaja el buje Deslize el cojinete en la cavidad de la h lice por el frente Para acomodar el cojinete completamente puede que sea necesario golpearlo ligeramente con un mazo martillo de goma Debe quedar a rente ligeramente adentro de la cavidad del buje 4 Deslice el ensamble de la h lice del paso No 3 sobre el eje de la h lice 5 Deslice la tuerca de expansi n de la h lice y la arandela plana sobre el ensamblaje de la h lice antes de la tuerca de la h lice 6 Ajuste la tuerca de la h lice de acuerdo a las especificaciones del Manual del Propietario por lo general 55 pies lb 7 Reinstale el cotter pin y tuerza los terminales 8 Rote la h lice manualmente en neutral para asegurar que rote libremente y no roce con otras partes del motor Para remover el cojinete del buje de la cavidad de la h lice use una varilla o socket de 1 de di
Download Pdf Manuals
Related Search