Cobalt Aquatics E-X-T Canister Filter Owner`s Manual PDF
Contents
1. 1 Unpack EXT filter and parts Inspect to be sure all parts are present and in working order If any parts are missing contact Cobalt Aquatics at 803 591 9500 2 Decided what installation style meets your specific needs best figure 2 3 4 or 5 The recommended and easiest installation is with canister below the aquarium and the pump mounted internally 3 For all installation options open up canister remove all media from bags and rinse media and trays until water is debris free and dear Reinstall media per figure 8 4 Re install lid and buckle down all for latches making sure top lip of canister and gasket are dean and free of particles Note Lid and media baskets are symmetrical and can fit in any orientation Internal pump mount option recommended for easiest install and maintenance and for low water or filter above tank setups fig 2 and fig 5 1 Cuta o dos approximately 3 long being careful to make dean flat cuts Caution Rough and uneven edges will make tightening and sealing the hose barb connection with the compression nuts very difficult 2 Turn compression nuts on hose barbs all the way up next to the pump housing Push the end of the hose onto the outflow hose barb all the way as far as you can into the compression nut While pushing on the hose with one hand to keep hose in position tighten the compression nut hand tight to lock hose and barbs together fig 9 Connect EXT pump intake strainer part ID 14 onto2. 2 Twist impeller housing counter dockwise to access impeller 3 Using soft brush or sponge remove any mineral build up and debris gathering on impeller impeller housing and impeller well parts rinse under running water Soaking parts in distilled vinegar for 15 20mins will help loosen mineral deposits 4 Once clean reassemble fig 1 and return to aquarium see install instructions above CAUTION The impeller part ID 4 and the pump body part ID 6 must not be disassembled Canister maintenance instructions Cleaning the filter media is necessary to keep canister running at peak flow rates and to keep tank dean and water clear odor and color free Maintenance should be performed every 3 4 weeks or as necessary as flow rate decreases as media clogs with dirt and debris Maintenance is simple for the EXT No need to un plug pump Simple steps 1 Turn valve counter dock ways all the way past min mark until the valve stops 2 Nt this spot the valve should be in closed loop mode and the pump is circulating water through the valve only and back to tank and the valve can be removed from the canister by simply lifting the valve upward fig 7 3 Take canister to sink and pour out some liquid trough the top intake and output holes now visible in the lid 4 Unhook the 4 lid latches and remove the lid 5 Remove media baskets Discard and replace top fine white floss and carbon layers Be sure to rinse all new media and the baskets before p
3. its option any EXT CANISTER FILTER which is deemed defective in workmanship or materials Please return the unit together with proof of date of purchase Call 803 591 9500 for return authorization and shipping address Damage or injuries resulting from negligence or misuse are nof covered by this warranty Incidental or consequential damages are specifically excluded This warranty gives you specific legal rights You may also have other rights which vary from State to state Because some states do not allow the exclusion of incidental or consequential damages this exclusion may not apply to you Questions or Missing Parts Call Customer Service at 803 591 9500 M F 9 5 EST SAVE THESE INSTRUCTIONS Chers clients nous vous remercions pour l achat de notre produit Nous sommes persuad s que vous serez satisfaits de son fonctionnement Pour viter un probl me quelconque li son utilisation nous vous prions de bien vouloir prendre connaissance de la notice d emploi ci dessous L USAGE DU PRODUIT ET SES CARACT RISTIQUES Les filtres EXT servent purer l eau des aquariums Ils poss dent une pompe ext rieure d aspiration permettant le fonctionnement m me dans une eau peu profonde DONNEES TECHNIQUES D BIT MAX PUISSANCE PROFONDEUR MAX MAX CAPACIT D AQUARIUM D ghi nm gall 26000 206 gph 800 Iph 6 5W 40 101cm 55gal 2081 L INSTALLATION ET LA MISE EN MARCHE FIGURE 4 Le filtre EXT peut tre installe de trois man
4. 26000 9 EXT U tube intake and output tubes 26600 2 Compression nuts 26000 2 EXT filter lid 30020 EXT 800 inline pump 30020 2 EXT Impeller housing 26000 3 EXT media basket see fig 8 P0512 Suction cups 30020 3 EXT Impeller housing O ring 26000 4 EXT valve block 26000 12 EXT elbow 30020 4 EXT 800 impeller 26000 5 _ EXT valve block O ring 26000 13 EXT diffusor 30020 5 EXT impeller shaft 26000 6 EXT canister gasket 26000 14 EXT pump intake strainer EXT pump housing 26000 7 EXT canister latch 26000 15 EXT U tube intake strainer P0512 Suction cups 26000 8 EXT 5 8 hose co O uan Aa co mN hg Horizontal LM P Multiple EXT for Mount S Larger Aquariums Intake A COBALT A Q T www CobaltAquatics com 803 591 9500 4 STAGE FILTER WITH INLINE PUMP 4 PHASE FILTRE AVEC POMPE EN LIGNE 4 ETAPA CON BOMBA DE FILTRO EN L NEA INSTRUCTIONS AND WARRANTY MODE D EMPLOI ET GARANTIE INSTRUCCIONES Y GARANTIA 2MZFITPPm CIMSTOL HME
5. CON CUIDADO ESTAS INSTRUCCIONES IMPORTANT SAFEGUARDS WARNING To guard against injury basic safety precautions should be observed including the following READ AND FOLLOW ALL SAFETY INSTRUCTIONS DANGER To avoid possible electric shock special care should be taken since water is employed in the use of aquarium equipment For each of the following situations do not attempt repairs by yourself return the appliance to an authorized service facility for service or discard the appliance 1 A If the appliance shows any signs of abnormal water leakage IDEA upi from the power source B Carefully examine the appliance after installation It should not be plugged in if there is water on parts not intended to be wet C Do not operate any appliance it it has a damaged cord or plug or if it is malfunctioning or has been dropped dropped or damaged in any manner D To Diod the possibility of the appliance plug or receptacle getting wet position aquarium stand and tank to one side of a wall mounted receptacle to prevent water from dripping onto the receptacle or plug A drip loop fig 10 should be arranged by the user tor each em connecting an aquarium appliance to a receptacle The drip loop is that part of the cord below the level of the receptade or the connector if an extension cord is used to prevent water travelling along the cord and coming in contact with the receptade If the plug or receptacle does get wet DON T unplug the cord Disconne
6. Thank you for purchasing a Cobalt EXT canister filtration system The Cobalt Aquatics EXT aquarium canister filter is the most innovative canister available Its unique inline pump allows complete flexibility on any aquarium terrarium or vivarium setup The innovative valve allows the pump to continue to run and keep vital circulation to your display even while the canister is disconnected for maintenance Easy to open and dose clips and 4 pre loaded removable media trays make maintenance a breeze The Cobalt MICRO UV clarifier is the perfect compliment to your new EXT filtration system The MICRO UV darifier removes water born microscopic algae bacteria and other organisms and keeps water dean and green free Always use Cobalt replacement filtration media featuring a variety of replacement chemical and biological media to replace used media or enhance your EXT with specialty media that remove Nitrates or Phosphates Whatever your needs Cobalt Aquatics has you covered TECHNICAL SPECIFICATIONS MAX FLOW RATE WATTAGE MAX DEPTH MAX AQUARIUM SIZE Loghi m gil 26000 206 gph 800 Iph 6 5 W 40 101cm 55gal 2081 ASSEMBLY amp MAINTENANCE INSTRUCTIONS ASSEMBLY Instructions The EXT canister filtration system is the most unique and flexible canister available It can be positioned above or below the aquarium and the pump may be placed inline either inside or outside the aquarium Suction cup mounts keep pump in place and vibration to a minimum
7. ande sous le couvercle de l enveloppe du filtre et sous le couvercle de la pompe d alimentation pi ce num ro 101477 GARANTIE LIMIT E DE 3 ANS Dans les trois ans compter de la date d achat originale Elle ne peut pas tre c d e ni transf r e tout acheteur ou utilisateur subs quent tout moment compter de la date d achat originale Cobalt Aquatics r parera ou remplacera son choix toute chaufferette d aquarium le filtre EXT qui pr sente un d faut de fabrication ou de mati res premi res Veuillez appeler au 803 591 9500 pour obtenir l autorisation de retourner le produit ainsi que l adresse d exp dition REMARQUE S assurer de bien envelopper la chaufferette pour la prot ger pendant le transport Le client est responsable des frais d exp dition apr s la r paration Si le probl me n est pas couvert en vertu des modalit s et conditions de la pr sente garantie le dient en sera inform et recevra une estimation des frais de r paration tous les frais d exp dition tant factur s au client Si le client refuse l estimation le produit sera retourn fret payable l arriv e Les dommages bris de verre ou blessures qui r sultent d une n gligence ou d une utilisation abusive ne sont pas couverts par cette garantie La perte de poissons les blessures et les pertes et dommages mat riels qui d coulent de l utilisation de cette chaufferette ne sont pas couverts par cette garantie Les dommages accessoires ou indirects s
8. arb connection with the compression nuts very difficult Connect the small section of hose to the long end of one of the U tubes Connect U tube strainer part id 15 to the now attached short section of hose Connect the remaining length of the hose to the short of the same U tube and install pump into aquarium in desired location Place canister under aquarium and bring hose from step 3 to canister Determine correct hose length to make connection then add 3 for play which will allow canister and valve movement but not enough slack to make hose kink Cut hose to this length and install on intake barb on valve closest to lever fig 7 Install elbow onto short side of remaining U tube Then connect the diffusor Connect remaining length of hose to long end of U tube and install to desired output location of the aquarium Confirm filter system input hoses are not full of water and in the aquarium to prevent siphoning and drain the line as best as possible Determine desired location of EXT inline pump Cut the hose in the desired spot being careful to make clean flat cuts and push on to the hose fig 3 Caution Rough and uneven edges will make tightening and sealing the hose barb connection with the compression nuts very difficult Push the ends of each hose onto the hose barbs all the way as far as you can into the compression nuts While pushing on the hose with one hand to keep hose in position tighten the compression nut hand tight t
9. ct the fuse or circuit breaker that supplies power to the iir ei Then unplug and examine for presence of water in the receptacle Close supervision is necessary when any appliance is used by or near dhikren To avoi ny do not contact moving parts or hot parts such as heaters reflectors lamp bulbs and the like Always unplug an appliance from an outlet when not in use before putting on or taking off parts and before cleaning Never yank cord to pull plug from outlet Grasp the plug and pull to disconnect Do not use an appliance for other than intended use The use of attachments not recommended or sold by the appliance manufacturer may cause an unsafe condition Do not install or store the appliance where it will be exposed to the weather or to emperatures below freezing Make sure an appliance mounted on a tank is securely installed before operating it Read and observe all the important notices on the appliance If an extension cord is necessary a cord with a proper rating should be used A cord rated for less amperes or watts than the appliance rating may overheat Care should be taken to arrange the cord so that it will not be tripped over or aded 10 This appliance has a polarized run one blade is wider than the other as a safety feature this plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician Never use with an extensio
10. ctar No use un dispositivo para un prop sito para el que no fue dise ado El uso de accesorios que no sean los recomendados o vendidos por el fabricante del dispositivo pueden provocar condiciones inseguros No instale ni guarde el dispositivo donde est expuesto a las condiciones clim ticas o a temperaturas por debajo del punto de congelaci n Aseg rese de que cualquier dispositivo colocado en la pecera est instalado de manera segura antes de hacerlo funcionar Lea y cumpla todos los avisos importantes sobre el dispositivo Si es necesario un cable de alargue se debe usar un a con las caracter sticas adecuadas Un cable adecuado para una menor cantidad de amperes o vatios que los que el dispositivo necesita vede recalentarse Se debe tener cuidado de ubicar el cable de manera que no puedan tropezar con l o dH 10 Ese dispositivo tiene un enchufe polarizado una clavija es m s ancha que la otra Como medida de seguridad este enchufe entrar en una toma de corriente polarizada solamente de una manera Si el enchufe no entra completamente en la toma de corriente d vuelta el enchufe Si contin a sin entrar comun quese con un electricista calificado Nunca use el dispositivo con un cable de alargue a menos que el enchufe se pueda insertar completamente No intente pasar por alto esta medida de seguridad E X T FILTER SPARE PARTS fig 1 E X T PUMP SPARE PARTS fig 6 ID Description Description R ECL 26000 1 EXT filter canister
11. don qui se trouve sous le niveau i la prise murale ou du connecteur si une rallonge est utilis e et cette m emp che l eau de s couler le long du cordon et d atteindre la prise Si la fiche ou la prise devient mouill e NE PAS d brancher le cordon D brancher le fusible ou le disjoncteur qui alimente l appareil D brancher ensuite le cordon et v rifier s il y a de l eau dans la prise Tne Une supervision troite est requise lorsque tout appareil est utilis par ou proximit des enfants Pour pr venir les blessures ne pas toucher aux pi ces mobiles ni aux pi ces chaudes comme les chaufferettes r flecteurs ampoules etc Toujours d brancher l appareil de la prise murale lorsqu il n est pas utilis et avant d installer ou de retirer des pi ces ou de nettoyer l appareil Ne jamais tirer sur le cordon pour sortir la fiche de la prise murale Saisir la fiche di a tirer pour la d brancher Ne pas utiliser un appareil d autres fins que l usage pour lequel il est con u L utilisation d accessoires non recommand s ou non vendus par le fabricant de l appareil peut pr senter un danger Ne pas installer ni entreposer l appareil dans un endroit o il sera expos aux conditions atmosph riques ou des temp ratures inf rieures au point de cong lation S assurer que tout appareil mont sur un r servoir est install solidement avant de l utiliser Lire et respecter tous E avis importants qui figurent sur l appareil Si une ral
12. e du rotor l aide d une brosse tendre Dans le cas o la pompe est installe l ext rieur de l aquarium figure 2 en tant qu une pompe de refoulement il est conseill d entretenir r guli rement le joint d tanch it qui se trouve sous le couvercle du rotor en le nettoyant et graissant avec de la vaseline Le cartouches de filtration doivent tre rinc es r guli rement avec de l eau de l aquarium non avec de l eau du robinet Le premier rin age doit tre fait apr s 2 mois partir de la premi re mise en marche du filtre et les suivants au besoin signal par la baisse visible du rendement de l appareil Pour optimaliser le fonctionnement du filtre il est conseill de remplacer les cartouches de filtration au moins tous les 12 mois En cas de besoin on peut enlever les algues ou le d p t calcaire du corps du filtre l aide d un chiffon doux ou une ponge Le r glage du rendement du filtre se fait par la rotation du module de commande dans le sens des aiguilles d une montre figure 6 dans une plage de 0 90 degr s La rotation de la vanne de 90 degr s coupe l arriv e d eau et permet d enlever le filtre de son logement en s curit sans la n cessit de d brancher la pompe du r seau lectrique par exemple pour nettoyer l int rieur du filtre Attention Affin d assurer une utilisation de longue dur e et fiable il est conseill de remplacer les trois joints d tanch it pi ce num ro 110611 sous le module de comm
13. en enjuagar de forma regular en el agua que se tira del acuario ino bajo el grifo La primera limpieza se aconseja realizarla 2 meses despu s de la primera puesta en marcha del filtro y las siguientes en caso de necesidad se alizada por la ca da del rendimiento del aparato Para obtener un trabajo ptimo del filtro se aconseja el recambio de los medios de filtraci n al menos una vez cada 12 meses En caso de necesidad la caja de la bomba se puede limpiar de las algas o del sarro usando un trapo suave o esponja La regulaci n del rendimiento del trabajo del filtro se hace girando el mando en el sentido de las agujas del reloj el dibujo 6 en un campo desde O hasta 90 grados Al girar la v lvula exactamente 90 grados cerramos la entrada del agua y podemos sacarlo de la caja de forma segura son necesidad de desconectar la bomba de la red de corriente el ctrica por ejemplo para limpiar el interior del filtro Atenci n Para garantizar un funcionamiento duradero y sin aver a del filtro se aconseja el recambio regular de las tres juntas no del art culo 110611 debajo del mando debajo del recipiente del filtro y debajo de la bomba de alimentaci n En caso de necesidad tambi n se puede reponer el rodete en la bomba de alimentaci n no del art culo 101477 GARANT A LIMITADA DE 3 A OS Dentro de tres a os a partir de la fecha de compra original La garant a no puede ser asignada ni transferida a ning n otro comprador o usuario posteri
14. gua al filtro Es el tipo de la instalaci n aconsejable para los acuarios est ndar para los peces El dibujo 3 la bomba de alimentaci n instalada fuera por debajo del nivel de agua cumple la funci n de la bomba de flujo Este tipo de instalaci n es aconsejable para los acuarios est ndar para los peces En este caso antes de la puesta en marcha del filtro es necesario suministrar el agua a la bomba mediante su absorci n a trav s de la manguera El dibujo 4 la bomba de alimentaci n instalada dentro del recipiente sobre el fondo cumple la funci n de la bomba de suministro del agua al filtro Esta soluci n es aconsejable en los filtros de un bajo nivel de agua EL MANTENIMIENTO La bomba de alimentaci n requiere una frecuente limpieza del rodete el dibujo 5a para eliminar de la c mara del rodete los posibles residuos mec nicos Para ello despu s de desconectar el aparato de la toma de corriente hay que desenroscar la tapa de la bomba el dibujo 5b girando en direcci n opuesta a la direcci n de las agujas del reloj quitar la tapa del rodete sacar el rodete y limpiarlo y limpiar su c mara con ayuda de un cepillo suave En el caso de que la bomba trabaje fuera del acuario el dibujo 2 cumpliendo la funci n de una bomba de flujo se aconseja un mantenimiento sistem tico de la junta que se encuentra debajo de la tapa del rodete limpi ndola debidamente y untando con vaselina t cnica Los materiales de filtraci n dentro del filtro se deb
15. h and install on intake barb on valve closest to lever fig 7 Install elbow onto short side of remaining U tube Then connect the diffusor Connect remaining length of hose to long end of U tube and install to desired output location of the aquarium Determine correct hose length to make connection then add 3 for play which will allow canister and valve movement but not enough slack to make hose kink Cut hose to this length and install on output barb on valve farthest from the lever fig 7 10 Because pump in located outside the aquarium the system is will need to be primed the first time To prime the filter lines for the first time simply remove output U tube from tank and suck on line briefly to start siphon on pump intake side Once siphon has started plug in EXT pump be sure to create a drip loop fig 10 When canister is full and system is running check all connections for any leaks If leaks are present unplug pump remove lines from water and drain into a pail or large bowl Fix leaking connections reinstall pump and start as before Once system is primed there should be no need to repeat siphon start as the lines will be primed with water and will not need to be redone O Co o On A aN External pump output side mount option fig 4 most advanced option 1 Cuta a of a approximately 3 long being careful to make clean flat cuts Caution Rough and uneven edges will make tightening and sealing the hose b
16. i res d pendamment de son usage Il est conseill d installer sur le tuyau d aspiration un pr filtre sous forme d une cartouche en mousse l index 101235 Attention Le pr filtre ne fait pas partie de l appareil et peut tre achet ind pendamment Figure 2 la pompe d alimentation est install e l int rieur du r cipient sa paroi et fonctionne en tant qu une pompe qui alimente le filtre en eau Cette solution est conseill e pour des aquariums standard avec les poissons Figure 3 la pompe d alimentation est install e l ext rieur du r cipient en dessous du niveau d eau et fonctionne en tant que pompe de refoulement Cette solution est conseill e pour des aquariums standard avec les poissons Dans ce cas il est n cessaire d amorcer la pompe en aspirant l eau dans le boyau d aspiration Figure 4 la pompe d alimentation est install e int rieur du r cipient au fond et fonctionne en tant qu une pompe qui alimente le filtre en eau Cette solution est conseill e pour des aquariums dont le niveau d eau est bas L ENTRETIEN La pompe d alimentation n cessite le nettoyage r gulier du rotor figure 5a affin d liminer les impuret s m caniques de la chambre du rotor Pour y proc der apr s avoir d branch l appareil de la source d alimentation il faut deviser le couvercle de la pompe figure 5b dans le sens contraire aux aguilles d une montre ter le couvercle retirer le rotor et le nettoyer et nettoyer la chambr
17. intake side of pump 3 Connect this other end of the hose to the long end of U tubes Connect the remaining length of the hose to the short of the same U tube and install pump into aquarium in desired location 4 Place canister under aquarium and bring hose from step 3 to canister Determine correct hose length to make connection then add 3 for play which will allow canister and valve movement but not enough slack to make hose kink Cut hose to this length and install on intake barb on valve closest to lever fig 7 5 Install elbow onto short side of remaining U tube Then connect the diffusor Connect remaining length of hose to long end of U tube and install to desired output location of the aquarium 6 Determine correct hose length to make connection then add 3 for play which will allow canister and valve movement but not enough slack to make hose kink Cut hose to this length and install on output barb on valve farthest from the lever fig 7 7 Plug in EXT pump be sure to create a drip loop fig 10 Because pump in located inside the aquarium the system is automatically primed and will start and fill canister on its on Once canister is TRE T running check all connections for any leaks If leaks are present unplug pump remove lines from water and drain into a pail or large bowl Fix leaking connections reinstall pump and start as before External pump intake side mount option fig 3 Cut a section of hose a
18. longe est requise utiliser un GUT u calibre appropri Un cordon d intensit ou de puissance inf rieure aux sp cifications de l appareil peut surchauffer Prendre soin de positionner le cordon i din ce que personne ne puisse tr bucher dessus ni l arracher du mur 10 Cet appareil est pourvu d une fiche polaris e l une des tiges est plus large que les autres Par mesure de pr caution cette fiche ne peut s ins rer que d une seule facon dans une prise polaris e Si la fiche ne s ins re pas compl tement dans la prise tenter dek retourner Si elle ne convient toujours pas contacter un lectricien Ne jamais utiliser une rallonge qui ne permet pas d ins rer compl tement la fiche Ne pas tenter de d sactiver ce dispositif de s curit PRECAUCIONES IMPORTANTES ADVERTENCIA Para evitar lesiones se deben tomar precauciones b sicas de seguridad incluyendo las siguientes LEA Y CUMPLA TODAS LAS INSTRUCCIONES DE SEGURIDAD PELIGRO Para evitar una posible descarga el ctrica se debe tener especial cuidado al usar los equipos de la pecera En las siguientes situaciones no intente realizar las reparaciones usted mismo Env e el dispositivo a un centro de servicio autorizado para que realicen el servicio o des chelo 1 A Si el dispositivo muestra alguna se al de p rdida de agua anormal descon ctelo de inmediato de la corriente el ctrica B Examine con cuidado el dispositivo despu s de la instalaci n No debe enchufarse si hay ag
19. n cord unless plug can je fully inserted Do not attempt to defeat this safety feature MISES EN GARDE IMPOTANTES AVERTISSMENT Des pr cautions de base doivent tre prises pour pr venir les blessures y compris les pr cautions suivantes LIRE ET SUIVRE TOUTES LES CONSIGNES DE SECURITE DANGER POUR PR VENIR LES RISQUES DE D CHARGE LECTRIQUE IL FAUT USER DE PRUDENCE PENDANT L UTILISATION DU MAT RIEL D AQUARIUM DANS CHACUNE DES SITUATIONS SUIVANTES NE TENTEZ PAS D EFFECTUER VOUS MEME LES REPARATIONS RETOURNEZ L APPAREIL A UN ATELIER DE SERVICE AUTORISE POUR LE FAIRE REPARER OU JETEZ L APPAREIL 1 A Si l appareil montre tout signe de fuite d eau anormale d branchez imm diatement l alimentation lectrique B Examinez attentivement l appareil apr s l installation Il ne doit pas tre branch si de l eau se trouve sur les pi ces qui ne doivent pas tre mouill es C Ne pas utiliser l appareil si le cordon ou la fiche a t endommag si l appareil fonctionne anormalement ou s il a t chapp ou endommag de Touren que ce soit D Pour viter que la fich de l appareil ou la prise ne se mouille placer le support et le r servoir de l aquarium sur le c t d une prise aer afin d emp cher que l eau ne s coule sur la prise ou la fiche Une boucle d gouttement fig 10 doit amp tre form e par l isofeur sur chaque cordon qui relie un appareil d aquariumdune prisemurale La boucle d gouttement est la partie du cor
20. o lock hose and barbs together Be sure to check that pump is installed in correct direction for flow rate per arrow fig 6 0 Bring lower end of pump hose to canister and determine correct hose length to make connection then add 3 for play which will allow canister and valve movement but not enough slack to make hose kink Cut hose to this length and install on output barb on valve farthest from the lever fig 7 9 Because pump in located outside the aquarium the system is will need to be primed the first time To prime the filter lines for the first time simply remove output U tube from tank and suck on line briefly to start siphon on pump intake side Once siphon has started plug in EXT pump be sure to create a drip loop fig 10 When canister is full and system is running check all connections for any leaks If leaks are present unplug pump remove lines from water and drain into a pail or large bowl Fix leaking connections re install pump and start as before With this installation option it is important to be sure the canister is full of water after maintenance is performed to keep system primed If not system could airlock and re priming will be necessary N O Ua1 Toon m9 Pump Maintenance Instructions Periodical cleaning of impeller and impeller housing are necessary to keep pump in optimal condition and ensure top performance 1 Unplug EXT pump and remove input and output lines from aquarium and drain hose lines
21. ont express ment excus Cette garantie vous conf re des droits sp cifiques Vous pouvez galement jouir d autres droits qui varient selon votre lieu de r sidence Etant donn que certains Etats ne permettent pas l exclusion desdommages accessoires ou indirects cette exclusion peut ne pas s appliquer dans votre cas CONSERVEZ CES INSTRUCTIONS Estimados Sefiores les damos las gracias por la compra de nuestro producto Estamos seguros que estar n satisfechos con su funcionamiento Para evitar cualquier problema relacionado con su uso le pedimos que lean atentamente estas instrucciones de uso LA DESTINACI N DEL PRODUCTO Y SUS PROPIEDADES Los filtros EXT sirven para limpiar el agua en los acuarios Tiene una bomba de absorci n de agua exterior que funciona tambi n en poca profundidad LOS DATOS TECNICOS VELOCIDAD DE FLUJO MAX POTENZA MAX PROFUNDIDAD CAPACIT MASSIMA DELL ACQUARIO ha n T 26000 206 gph 800 Iph 6 5 W 40 101cm 55gal 2081 EL MONTAJE Y LA PUESTA EN MARCHA EL DIBUJO NO 4 El filtro EXT puede ser montado de 3 formas dependiendo de su destinaci n Sobre la manguera de absorci n se aconseja la colocaci n de un prefiltro el dep sito esponjoso no del art culo 101235 jAtenci n El prefiltro no es parte del aparato y se puede comprar como una pieza adicional El dibujo 2 la bomba de alimentaci n instalada dentro del recipiente en su pared cumple la funci n de la bomba de suministro del a
22. or En cualquier momento a partir de la fecha de compra Cobalt Aquatics reparar o reemplazar a su discreci n los calentadores de pecera el filtro EXT con defectos en la fabricaci n o los materiales Llamar al 803 591 9500 para obtener una autorizaci n de devoluci n y una direcci n para el env o NOTA Aseg rese de envolver el calentador con cuidado para protegerlo durante el env o El consumidor pagar el costo del env o luego de la reparaci n Si el problema no est cubierto por los t rminos y condiciones de esta garant a se avisar al consumidor y se le dar un presupuesto de los costos de reparaci n con todos los costos de env o a cargo del consumidor Si el presupuesto no es aceptado el producto ser devuelto con los costos de tranporte por cobrar Los da os la rotura de vidrios y las lesiones que sean consecuencia de la negligencia o uso incorrecto no est n cubiertos por esta garant a La p rdida de peces las lesiones personales la p rdida de bienes o los da os que resulten del uso de este calentador no est n cubiertos por esta garant a Est n espec ficamente excluidos los da os incidentales o a consecuencia de Esta garant a le otorga derechos legales espec ficos Usted tambi n puede tener otros derechos que var an de un estado a otro Debido a que algunos estados no permiten la exclusi n de los da os incidentales o consecuenciales es posible que esta exclusi n no se aplique en su caso CONSERVAR
23. pproximately 3 long being careful to make dean flat cuts Caution Rough and uneven edges will make tightening and sealing the hose barb connection with the compression nuts very difficult Connect the small section of hose to the long end of one of the U tubes Connect U tube strainer part id 15 to the now attached short section of hose Connect the remaining length of the hose to the short of the same U tube and install pump into aquarium in desired location Confirm filter system input hoses are not full of water and in the aquarium to prevent siphoning and drain the line as best as possible Determine desired location of EXT inline pump Cut the hose in the desired spot being careful to make dean flat cuts and push on to the hose fig 3 Caution Rough and uneven edges will make tightening and sealing the hose barb connection with the compression nuts very difficult Push the ends of each hose onto the hose barbs all the way as far as you can into the compression nuts While pushing on the hose with one hand to keep hose in position tighten the compression nut hand tight to lock hose and barbs together Be sure to check that pump is installed in correct direction for flow rate per arrow fig 6 Place canister under aquarium and bring hose from step 3 to canister Determine correct hose length to make connection then add 3 for play which will allow canister and valve movement but not enough slack to make hose kink Cut hose to this lengt
24. ua en las partes que no deben mojarse C No ponga en funcionamiento ning n dispositivo si el cable o el enchufe est n da ados o si no inona bien o si se cay o tiene cualquier otro tipo de da o D Para evitar la osibilidad de que AA del dispositivo o el recept culo se mojen coloque la base y la pecera a un costado del enchufe en la pared ara evitar que el agua gotee hacia el recept culo o 4 enchufe El usuario debe formar un bucle de cable fig 10 por debajo del enchufe en todos los cables que conectan un dispositivo de b pecera con un enchufe El bucle de cabe es la parte del cable que queda por debajo del nivel del recept culo o de la conexi n en caso de que se use un cable de alargue para evitar que el agua corra por el cable y entre en contacto con pma Si el enchufe o el recept culo se mojan NO desenchufe el cable Desconecte el fusible o el interruptor de circuito que suministra electricidad al dispositivo lik o desenchufe y examine para controlar que no haya agua en el enchufe Es necesario vigilar con cuidado cuando los ni os utilicen o est n cerca de cualquier dispositivo Para evitar lesiones no toque partes en movimiento o calientes como calentadores reflectores focos de luz etc Siempre desenchufe un dispositivo de la toma de corriente cuando no est en uso antes de colocar o quitar alguna parte y antes de limpiarlo Nunca jale el cable para desconectar de la toma de corriente Tome el enchufe y jale para descone
25. utting back into EXT 6 Rinse the sponge and ceramic rings in old aquarium or De chlorinated tap water using either type of water will protect the good nitrifying bacteria colonies that have developed on the media to remove any dirt debris or excess biofilm 7 Reinstall baskets per figure 8 and latch lid closed making sure there is no dirt or debris on the top canister lip or the gasket in the lid 8 For internal pump mount or intake side external mount options return canister back to aquarium and re install the valve in reverse order as before fig 7 System should start to fill canister then once canister is full start to push filtered water back to aquarium as before automatically 9 For output side external mounts lid should be canister should be refilled with dechlorinated water lid re installed then more de chlorinated water poured down 2 top holes until nearly full Now return canister back to aquarium and re install the valve in reverse order as before fig 7 System should start to push filtered water back to aquarium as before immediately If system airlocks unplug the pump and place output U tube down into a pail and allow siphoning of water through canister to flush any air our of system Once air is gone put U tube back into aquarium as before and restart pump System should now function normally LIMITED 3 YEAR WARRANTY Within three years from the date of original purchase Cobalt Aquatics will repair or replace at
Download Pdf Manuals
Related Search