チタニウム触媒ストレートパイプ - TOMEI POWERED USA Inc.
Contents
1. 84 0 39 0N m 3 0 4 0kgf m 84 0 39 0N m 3 5 4 0kgf m 2 3 N2. 1 2 2500rpm 3 t He a A A
3. KIT CONTENTS Below is the contents of this kit with the quantity listed in brackets mmm Flange Bolt Nut M10 x P 1 25 4 M10 x P 1 25 4 Decat Straight Pipe 1 Gasket 2 Cable Tie 1 EXPREME Ti Sticker 2 Bolt Smooth Paste 1 REQUIRED TOOLS These tools are the bare minimum required for the job General Engine Maintenance Tools Torque Wrench Service Manual A CAUTION W This product is designed to be used for off road competition purposes only W This product is to be installed by a qualified professional in a fully equipped workshop W This product was designed specifically for the application specified If the attempt was made to use this product on another engine car other than specified then you will risk damaging this kit and or the engine or components related with it W This product is to be installed with the appropriate tools and equipment to prevent any engine failures and injuries or bodily harm N WARNING M This product is to be installed when the engine and engine bay is cold Mi Please be sure that all parts are fitted correctly to avoid any possible fire risk hazards 1 REMOVAL OF THE STOCK CATALYTIC CONVERTER A This manual only provides the simple instructions For more details please refer to the vehicles official service manual 1 Disconnect the cars battery negative terminal 2 Remove the stock catalytic converter 2 TOMEI STRAIGHT PIPE INSTA
4. AN ax Ae A 1 A 2 2 TOMEI HDX Y Nor lt gt M10 Zi 34 0 39 0N m 3 5 4 0kgf m 1
5. TOMEI 11 12 M19Y960 INSTALLATION MANUAL NISSAN TYPE A EXPREME Ti Titanium CAT Straight Pipe for NISSAN TYPE A PART NUMBER HE RPS13 K PS13 C S14 S15 HR32 HCR32 HNR32 HR33 APPLICATION ER33 ENR33 ECR33 BNR32 BCNR33 BNR34 EA31 CA31 HA32 PA32 HC33 HC34 GC34 PY32 PAY32 PBY32 HBY33 HY33 PY33 FPY32 FHY33 WGC34 WGNC34 RNN14 HNP10 HNP11 2pD English DD TOME TOMEI Please carefully read this manual prior to installation Please also refer to the NISSAN Service Manual with this Manual After the installation has been completed pl
6. the Titanium exhaust before starting the engine INSTALLATION VERIFICATION 1 Check again the vehicle that there are no parts interfering with any other components 2 Start the engine and let it idle first before taking it up to 2500 RPM to check and listen for any signs of exhaust leaks or any abnormal sounds Then recheck the car again for any loose parts or gas leaks 3 After the initial test drive check the car again for any signs of exhaust gas leakage and any loose parts bolts and nuts A WARNING Any interference with any parts components can pose a fire risk hazard so please meticulously check the car after the install Any exhaust leaks can decrease performance efficiency and also pose a health risk hazard with toxic exhaust gas poisoning If there is anything felt abnormal when driving please stop immediately and check the car over When any work or checks are to be done with the metal exhaust components then please do so when it is cold to prevent any burns and injuries If any parts are lost or have fallen off then does not restart the car until the missing part s can be replaced properly N CAUTION The vehicles characteristics and exhaust backpressure may change after installing this product so after the install you may need to have the ECU map settings and boost settings checked and adjusted accordingly to suit the new setup TOME POWERED mc HRH RENT KB 7194 0004
7. 1737 3 TEL 042 795 8411 FAX 042 799 7851 1737 3 Tsuruma Machida shi Tokyo 194 0004 JAPAN TEL 81 42 795 8411 main switchboard http www tomel p co jp 9 00 18 00 If you have any questions in regards to the installation of this product please contact your local authorized Tomei Powered distributor OPEN Monday Friday National holidays and public holidays excluded 09 00 18 00 NISSAN TYPE A 11 12 M19Y960 TITANIUM STRAIGHT PIPE NISSAN TYPE A INSTALLATION MANUAL 11 Dec M19Y960 8
8. LLATION Illustration of the mounting position of each bolt amp gasket The installation of the bolts included in the kit is shown below lt Rear Muffler Side Front Front Pipe Side lt Torque settings for the kit contents gt Oe Exhaust Gas Temperature Sensor Gasket Flange Bolt M10 Flange Nut 34 0 39 0N m 3 5 4 0kgf m Cable Tie Use the bolt smooth paste provided to prevent the bolts from seizures and rust welds MOUNTING INSTRUCTIONS 1 Install the Straight Pipe with the supplied gaskets bolts and nuts FRONT PIPE SIDE Use the Supplied Gasket Ref Torque Settings Nut Ref 34 0 39 0N m 3 0 4 0kgf m MUFFLER SIDE X Use the supplied Gasket Ref Torque Settings Nut Ref 34 0 39 0N m 3 5 4 0kgf m 2 Secure the Exhaust Gas Temperature Sensor to any part of the body with the supplied Cable Ties 3 Reconnect the cars battery negative terminal N CAUTION Please check all clearances with the vehicles body and make sure that the bolts are not interfering with anything else The clearances can change from vehicle to vehicle Be sure that all the bolts are tightened correctly so that there is no pollution caused form any exhaust leaks After fitting the straight pipe and or catalytic converter please check that there are no signs of oil dirt so as not to burn bake it later when the car is running TIP clean all fingerprints and oil off
9. ease keep this manual for future reference If the install was done in a shop please make sure to give this manual to the owner Thank you for purchasing another quality TOMEI product This TOMEI Titanium Exhaust Straight Pipe has been designed for true competition use to maximize weight reduction and exhaust flow efficiency YZ MT0xP 1 25 4 MIOxP 1 25 4 1 1 EXPREME Ti 2 1 A
Download Pdf Manuals
Related Search