VFS-1BMC 取扱説明書(英文A3)Ai10_OL
Contents
1. wire 12 13GA that we sell If the wires are soldered in an opposite connection or insufficiently a short may occur When you make a mistake the ESC will be damaged B To battery minus To Motor terminal C MC __ MB To Motor terminal B To Motor terminal A MA C B To battery positive read this instruction manual Technical Specifications Corresponding Motor Manufactured RC car sensor type brushless electric motors Star Wire Control Method PWM variable frequency system Max Peak Current 3120A FET Specifications Max Continuous Current 780A FET Specifications Operating Input Voltage 4 8 7 4V Ni cd Ni MH Li PO BEC Output Voltage 6V BEC Output Current 2A Instant maximum Drive Frequency 32Point 52Step 2 0KHz 12 0KHz Brake Frequency 52Step 500Hz 2 5KHz Size 33 4x37 0x16 8mm Weight 30 8g Operation Forward Brake Recommended Motor Limit 4 5 T with heat sink and fan installed 2 5 T Note to handling oThis product is made and sold with the intent of use for land RC models oConnect the receiver servo and ESC securely oDo not use when you hear thunder when it is raining or when there are puddles of water oDo not use when judgement is hindered due to fatigue consuming alcohol or under medication oStore in a place where it is out reach from infants and children oWhen not in use disconnect the battery o Do not use where there are people on the road oNote sufficiently tha2. 5 Business hours Monday through Friday except for Saturday Sundays and Japanese National holiday 9 00 to 12 00 13 00 to 17 00
3. KO P70PO 1 DWE Professional Brushless Motor Controller Thank you for purchasing the VFS 1BMC This manual describes the use of this speed controller ESC with a sensor equipped brushless motor used for the highest level of racing In order to utilize the performance of this product you must 1 ill VFS 1BMC Instruction Manual Product Features Variable Frequency System PAT Possibility according to the throttle setting and motor drive frequency modification Modification of the setting which corresponds to the cat egory and course layout is possible glCS Interactive Communication System It is possible to change configurations and parameters using a PC when used with the ICS USB adapter sold separately 1 Neutral brake setting OFF 255 step adjustment 2 Brake frequency 52 step adjustment 3 Battery Saving 3 setting modes Li PO Ni MH 5 6 cell mode and Ni MH 4 cell adjustment 4 VFS frequency configuration 32Point 52Step 2 0KHz 12 0KHz minternal 5 model memory The possibility of the product setup has become stream lined Only when using a PC operating on Windows and using the ICS USB adapter No 61018 mw Overheat amp Overcurrent Protection equipment If you make a mistake in the setup of the motor the pinion gear and power the safety design will cut Wiring Procedure Silicon wires are not included in VFS 1BMC Please use our genuine fluorescent silicon
4. e You can download from our company s home page the configuration data About cooling When installing the world spec kit that is sold separately No 45521 the over current and high power motors that could not be used previously can now be used This is very effective with modified Touring and 4wd buggy cars CIO ED Installation Technique 1 The heat sink is attached to the aluminum plate gold of the VFS 1BMC using the double sided tape 2 The cooling fan is installed with the supplied screws onto the heat sink 3 The connector of the cooling fan is connected to the BMC Repair inquiry http www kopropo co jp oWhen you believe that you have had a breakdown Please inspect and reread this instruction manual again When you do not understand something please contact our service department When consulting our service department please inform them about the status of breakdown in as much detail as possible oThe model of the transmitter RC car motor and battery oWhen it broke down the usage condition status and content oCustomer name address and contact information oWhen a repair is requested please include the above mentioned contents when sending in the repair oPlease prepay the postage for all items sent to us for repair KO P 70PO KONDO KAGAKU Co Ltd E mail Adress webmaster kopropo co jp 4 17 7 Higashi Nippori Arakawa Ku Tokyo 116 0014 Japan TEL 03 3807 7751 FAX 03 3807 815
5. sensor wire is installed in the sensor wire connector VFS 1BMC will not operate unless the signal of the sensor wire is received Sensor wire connector A sensor wire that is attached to a motor can be used Cooling fan connector The world spec kit cooling fan sold separately can be installed oPlease be sure to install the wiring before beginning oWhen configuring the ESC please make sure that power is not delivered to the tires by removing the pinion from the motor oBefore configuring please set the transmitter HIPOINT BRAKEPOINT ATV and EPA to its default factory default setting To configure a KO transmitter for reset simultaneously press the positive and negative buttons on the transmitter olf you have ABS and acceleration function in your transmitter please set these functions to OFF oUnless the standard configuration is set it will not operate correctly z z The transmitter s neutral high Standard configuration point and brake point will be stored in the VFS 1BMC Configuration is performed with the operation of the power switch and the set button Power switch While pushing the set button turn the power switch to ON When LED lights up the set button is released The LED will flash a pattern of 1 time The throttle trigger should remain in the neutral position and press the set button once Press while at neutral The LED will flash a pattern of 2 times Hold the throttle trigger to
6. t you did not make a mistake in the polarity of the battery oOnly use our company s genuine products when connecting equipment and installing optional parts oTurn on the transmitter power first Then turn on the receiver Control from the transmitter oAfter the run pay attention to the heat generation of motor battery ESC etc o For the battery cord and the motor wire etc make sure they do not touch and short circuit oWhen setting up remove the motor pinion olf the product gets wet discontinue use and send it in for repair oPlease do not subject this product to strong impacts oPlease note sufficiently the parts that are angular and pointed to prevent injury oResolution remodelling of the product may become a cause of a short or other accidents and there are times when we will refuse the acceptance of repair in our service department 1 Install the VFS 1BMC into the RC car with double sided tape Install it in a safe place to avoid an impact from a crash Install the power switch in a place where the slide switch and button are easy to access 2 The VFS 1BMC has soldering post where you must install the silicone wires with the use of solder Following the inscriptions on the aluminum plate MA MB and MC are for the motor terminals B and B are for the battery plus and minus respectively Please note the polarity of the battery when connecting 3 As for servo lead coming from the ESC connect it to 2CH of the receiver 4 The
7. the full throttle position and press the set button once TOO gt Hold full throttle and press The LED will flash a pattern of 3 times Hold the throttle trigger to the full brake position and press the set button once Q 0O O gt OQ gt gt V x Y N P y Hold full brake and press Once the standard configuration is completed the LED will stop flashing The VFS 1BMC can store up to 5 types of setups Model select While pressing the set button turn the power switch to ON The LED will come on and then go out after approximately 3 seconds After the LED goes out release the set button Upon completion you are entered into the model selection mode To change the model press the set button The number of flashes 1 5 will indicate model selected The current model used is displayed with the frequency of the LED flashes Factory shipment configuration is listed below Wooo 0 0 5 times flashing Model 5 Buggy Once the model is selected turn the power off to store the selected model memory When this item is shipped the factory settings are configured Depending upon the motor and battery used the highest performance will be achieved when modified with the ICS To modify the configuration with the ICS the ICS USB adapter No 61018 which is sold separately will be required You can download the latest version of the software for configuration from our company s home pag
Download Pdf Manuals
Related Search