ケーブルレリーズブラケット 説明書（700KB）
Contents
1. 2 ase tJ 3 12. 5 6 5 1
3. 2 3 oe ir ee 4 Vixen Instruction Manual for Cable Release Bracket 5 17 3 Higashitokorozawa Tokorozawa Saitama359 0021 Japan Vixen Co Ltd Phone 81 4 2944 4141 International http ww
4. 7 5 6 2 8 3 4 Vixen SE ek a ae o prms a Co wasn orka un 2 o o ren oraa en 2 Co ozm smes o o o meson 0momErEN EEEE AE T 4 4
5. O j 7359 0021 5 17 3 J TEL 04 2944 4000 FAX 04 2944 4045 5x ZZ http www vixen co jp 54 1 8167 0 5S o IN 22mm 80mm 80mm 6 D SR 1
6. Less than 7mm in width 5 Angle bolt om Shutter protection rubbers 1 Attach the shutter protection rubber onto the shutter button of the camera Any strain on the shutter button may prevent the shutter protective rubber from sticking on it securely and it will lead you to the loss of the shutter protection rubber Make Sure to clean the shutter button before you put the shutter protective rubber on it 4 Place the camera on a soft cloth with the lens facing upward to avoid scratching the camera body Install the camera onto the camera bracket so as not to hit the side of the camera body against the tip of the angle bolt but as close as possible Keep a space Fix the camera on the camera bracket by tightening the fixing of about 1mm screw into the tripod socket on the bottom of the camera 4 Shutter protection rubber Fixing screw ams 2 Loosen the angle setting nut and shift the cable release 5 Loosen the angle setting nut and the cable release head i bracket fully to the upright position Then tighten the angle holder and adjust the angle of the cable release bracket so 5 rea Cabe ee setting nut until the cable release bracket is locked stably Cable release bracket that the cable release head comes just above the shutter retaining nut Insufficient tightening of the angle setting nut may result in button Confirm if the tip of the cable hits the center of the Cerea aa scratching the camera s
7. release use it correctly 2 Using an aged or a stiff camera cable release may cause blurring by vibration or missing a shutter chance Check movements of the camera 8 You are successful in attaching the cable release bracket if cable release before you use it you can push down the cable smoothly without clogging Take reverse procedures with care not to scratch the camera body when you remove the camera from the cable release bracket 3 4 3 You may need to detach the camera cable release from the cable release bracket when you exchange the battery or data memory card Do not attempt exchanging the battery or data memory card forcedly with the camera attached The camera may damage or the data may Shown with an optional Universal disappear digital camera adapter 4 There is a tripod socket on the bottom of the camera fixing screw The cable release bracket can be used with a camera tripod and it will be convenient to use in conjunction with an optional universal digital camera adapter
8. hutter button when the cable is pushed down Then tighten head holder ju the angle setting nut and cable release head holder again Angle setting 5 Angle setting nut nut 3 Attach a commercially available cable release to the cable 6 If the adjustment above 5 is not successful and the cable release head holder 1 Do not forcedly screw the cable Sa renee does not hit the center of the shutter button loosen the release into the cable release head holder as it may damage EE camera fixing screw and move the camera bracket back and the threads Be sure to attach the cable release into the cable l forth slightly so that the cable release head comes just above release head holder before you mount the camera on the the center of the shutter button camera bracket Cable release head holder Camera bracket 7 Turn on the power of the camera and confirm that the camera cable release works correctly and smoothly when the cable is pushed down When you feel a clogging of the cable check if the cable is forcedly bent halfway or check if the tip of the cable is away from center of the shutter button If this is the case repeat the procedures 5 and 6 until you get smooth movements 2 1 Use a compact camera that is appropriate to the specifications of this cable release bracket When you use the cable release bracket for astrophotography a camera cable release with self stopper is recommended Please read instructions for the camera cable
9. w vixen co jp F a x 81 4 2944 9722 International Siemensring 44c D 47877 Willich Germany Vixen Europe GmbH foo 0215478165 0 http www vixen europe com F a x 02154 8165 29 Shown with a digital camera sold separately Preface Thank you for your purchase of a Vixen cable release bracket This product is a bracket for installing a camera cable release on it The camera cable release is sold separately Purchase one that is appropriate to your camera It may be necessary to detach your compact digital camera or camera cable release from the cable release bracket when you exchange the battery or data memory card For details please refer to instructions on your camera or camera cable release Dimensions of Camera and Camera Cable Release available for this product 22mm in distance from the side of the camera body incl projection to the center of the shutter button Shutter Button Protection rubber Pre attached on the angle bolt Protection rubbers Pre attached on the side of the camera bracket Protection rubbers Pre attached on the bottom of the camera bracket 80mm in height from the bottom of the camera body to the top incl projection 80mm in distance from the side of the camera body incl projection to the tripod socket Minimum dimensions of camera cable release e More than 12mm in length i es Camera bracket Protection rubber Pre attached on the fixing screw
Download Pdf Manuals
Related Search