C。NTEC
Contents
1. 3 5 inch Hard Disk Drive PC HDD3200 3 For the IBM PC AT User s Guide CONTEC A Handing Precautions PC HDD3200 3 is designed to withstand normal handing during unpacking and installation Take care must to avoid excessive mechanical shock or electrostatic discharge ESD that can permanently damage the PC HDD3200 3 and void the warranty Hard drives are typically damaged because of ESD rough handling or shock and vibration When the PC HDD3200 3 is not in its shipping container or installed in its proper host enclosure it must remain in the antistatic bag To prevent damage do not unpack your WD Caviar drive until you are ready to install it ORE PC HDD3200 3 amp CRRATBX ELT SVBEDOZWET ASG LAE OFRET BAS HE SWETEIBRMYLET PC HDD3200 3 FRY TR 5 ITIL TARE ORR 2H OME CKAN TF 2 Y Eat a ae a at FAR F E AGED BHT DANE 5 ELTI ESD Ik a An RFA RAY FIA ODD OFA VELBA RV Oe RBC LAZbOCH Hehe VIA EMIE y CAEL TOR LT ROCK FAV 1 Standard Factory Connectors J2 b G 3 ri oo0o00000000000000000 e0 20 ll o 6 coocooooaoocoa aooocoooaocojjlooaocoa 2 8642 40 5V Figure 1 Component Locations 1 PC HDD3200 3 2 Jumper Settings The PC HDD3200 3 has a jumper bock J8 located next to the 40 pin connector on the drive You can assign the PC HDD3200 3 as either a single master or slave drive Refer to Figure 2 for an illustration of all jumper settings Single Drive Mode Fa2. ations Recommended setup 6296 x 16 x 63 parameters Do not exc ed the maximum sector capacity when specifying linder x Head x SPT the number of cylinders heads and sector per track Current requirement Spinup 1 8A Max Read Wirite 240mA Seek 580mA Power dissipation Idle Standby Sleep Humidity 5 85 RH non condensing 5 95 RH non condensing 33 C Maximum wet bulb 33 C Maximum wet bulb Anti shock Less than 10G Less than 150G during operation 3ms half sine pulse 3ms half sine pulse era during operation 20 300Hz 20 500Hz 5 J2 Pin Assignments The PC HDD3200 3 interfaces with the host I O bus via the 40 pin connector J2 illustrated in Figure 1 Table 1 identifies the pin numbers of the J2 connector and the corresponding signal names and signal functions Table 1 Pin Assignments Pin Assignment __ Pin Assignment __ HRST GND HD8 3 PC HDD3200 3 6 External Dimensions 146 05 4x 6 32 UNC 2B 6 25 Max DEEP mm Note Mounting hole location tolerance is 0 25mm Numbers in boxes are basic numbers A 41 984 LZF9331 980916 PC HDD3200 3 4
3. ctory Setting If the drive you are installing is the only drive in your system use this setting Master Drive Mode Dual Master If the drive you are installing is the master drive in a two drive system use this setting Slave Drive Mode Dual Slave If the drive you are installing is the slave drive in a two drive system use this setting Single Drive Mode Master Drive Mode ans Drive Mode ual Master ual Slave 97631 97531 97531 m oo OQ Oo 00o 00 ORYO 0o o 0 OWO o O O ORO 108 6 4 2 108 6 4 2 108 6 4 2 Place a jumper shunt on pins 3 5 Place a jumper shunt on pins 5 6 Place a jumper shunt on pins 3 4 Figure2 Jumper Setting 3 Mounting Restrictions Screw Size Limitations The PC HDD3200 3 is mounted to the chassis using four 6 32 screws Recommended screw torque is 5 in lb Maximum screw torque is 10 in lb Grounding For best results mount the drive with all four screws in the side grounded to the chassis positions A C D and F in Figure 3 You must ground the drive with at least one mounting screw Side Mounting Use four metal screws in A C D and F If less than four screws are used remove in this order C D and then F You must use a screw in position A Top Face Mounting Use four metal screws in 1 2 3 and4 If less than four screws are used remove in this order 2 4 and then 3 You must use a screw in position 1 Figure3 Grounding Diagram PC HDD3200 3 2 4 Hardware Specific
Download Pdf Manuals
Related Search