TLS1-VOL 取扱説明書
Contents
1. N N IN N Q TLS1 VOL DC0 0 100 0V 4 0V 8 5V 4g R 440mm 300mm BTLS1 VOL 32. RG731B8X E 1 gt gt 2 TLS1 VOL 3 TLS1 VOL SENS DATA gt Y RG731BX BIND BATT SENS RG611B BATT DATA
3. LED TLS1 VOL TELEMETRY F PACK V F PACKC XG7 1 TLS1 VOL 2 ON 3 MAX 4 HE
4. ESC ESC TLS1 VOL TLS1 ADP 5 TL1 PWR TL1 BVM ESC TEL 06 6732 0200 9 00 13 00 14 00 17 30 http www jrpropo com REMOTE 577 0809 RANAH 2 JR senic NEM C94A J PROPO Tui Operation Manual TELEMETRY SENSOR SERIES TLS1 VOL Voltage Sensor m p DUAL MODULATION SPECTRUM SYSTEM Thank you for purchasing this JR product To allow correct and safe use of this product be certain to read this operation manual
5. TLS1 VOL LED BR TARAA Y ee RG731BX TLS1 VOL ESC ate A pa a
6. About the TL Logo This logo is only included on products that support the JR Telemetry System Tp z T 5 bi directional This product is exclusively for use with communications products that incorporate the TL logo Features The sensor can be used to measure total voltage or the voltage of a single cell Because the unit measures voltage difference there is no polarity requirement for the sensor lead The LED indicates voltage measurement is taking place The sensor wire must be soldered to the battery leads or terminals Product Contents e TLS1 VOL Sensor Main Unit e Operation Manual this document For your safety be sure to observe the following points In order to protect against injury to users or third parties or damage to property please observe the following The information is divided and explained using the following symbols Caution Items are explained using this indication Obligatory Items are explained using this indication Prohibited Items are explained using this indication A If the product is used with a voltage other than the rated voltage it will cause misdetection or damage to the sensor A Be sure to securely fix the sensor In the situation where the sensor comes into contact due to the influence of vibration damage will be caused A Be sure also to securely fix the harness coming from the sensor If he harness becomes tangled it may cause an
7. A Caution Be careful handling the soldering iron Main battery a Sold separately Main battery connector Electric Motor Sold separately Sold separately fam Notes 1 When you are using a 2s LiPo and regulator to supply your receiver you may use the TLS1 VOL to measure true receiver battery voltage indicated as F PACK V on the transmitter The TLS1 VOL can be wired into the switch harness before the regulator 2 An alternative method of connecting the TLS1 VOL to your battery is to plug it into your LiPo balance connector measuring either single cell or whole pack voltage 3 When multiple sensors are to be connected When you wish to incorporate several sensors in addition to the TLS1 VOL please use the optional the TLS1 ADP This adaptor is configured to allow simulta neous connection of up to five sensor types However it is not possible to use more than one of the same sensor type at the same time E For further questions or inquiries please contact your local dealer or JR distributor in your country http www jrpropo com JR IREMOTE__ CONTRO
8. DP or a Y harness turn on the power to the receiver The sensor will activate automatically Note Occasionally noise generated by the motor may cause a high maximum voltage to be recorded simply reset clear the maximum value on the transmitter to obtain correct values If the LED glows the voltage is being sensed correctly Please check the transmitter indications If the LED does not glow check the wire connections including the sensor communications harness IMPORTANT Be sure to remove the bind plug prior to use With receivers such as the RG731BX or RG831B which require a bind plug be sure to remove the bind plug from the receiver prior to use as it interferes with the bi directional communications and telemetry data will not be displayed on the LCD screen N 5 Installation Method 1 Attach the sensor wires to the electric power source wires polarity does not matter Note Be sure to attach the wires securely by carefully soldering the connections Be sure to use heat shrink tube or insulation tape to avoid short circuits 2 Be certain to securely mount the sensor to the aircraft Note Be sure that none of the wires or connectors contact the moving components 3 After fixation of the TLS1 VOL to the aircraft connect the sensor communications harness to the receiver s SENS or DATA port Note Use either a Y harness or TLS1 ADP to connect the sensor communications harness to the rece
9. SJRPROPO DMSS 2 4GHz SST TELEMETRY SENSOR SERIES TLS1 VOL 1 DUAL MODULATION SPECTRUM SYSTEM JR TL JR LED TLS1 VOL
10. accident Further he base of the harness may be cut Pay adequate attention to the remaining battery amount during lights If the remaining battery amount becomes low there may be cases where incorrect readings occur Do not use any component which has been damaged included wires or connectors Do not fly until check is complete Do not disassemble or modify this product Q o ensure that the sensor is functioning as desired please test accordingly Do not get the product wet or damage may be caused Do not use he product in environments where condensation occurs Specifications Product Number TLS1 VOL Detection Range DC 0 0 100 0V Operating Voltage 4 0 8 5V Weight 4g Length 440mm sensor wire length 300mm Configuration BTLS1 VOL LED TLS1 VOL Main Unit Se sor wire Note that the sensor lead must be soldered to your point of measurement Be careful soldering always have the battery unplugged and remember the solder ing iron is hot Transmittor Operation Telemetry type Flight pack voltage F PACK V This sensor dose not record capacity it only reads voltage To set a voltage alarm in the transmitter please refer to the transmitter instruction manual Note the XG7 does not support telemetry Operation Confirmation and Cautions Refer to the drawing on the right to connect the unit After the TLS1 VOL is connected to the receiver if necessary using a TLS1 A
11. iver If there is an empty slot available on the receiver connect the battery connection to the empty slot and connect the sensor communications harness to the SENS or DATA slot F RG731BX Connection Example Connect to the BIND BATT SENS terminal For the RG611B and other receivers connect to the BATT DATA terminal TLS1 VOL connection example to the main power battery pack Solder the sensor lead to the battery TLS1 VOL Bind Plug a m LED X connectors positive pole and negative pole Note Polarity of the sensor wires is not important Sold separately Y Harness Sold separately Close up of the connector Be sure to check the polarity before installation Teh DMSS 2 4GH RECEIVER with XBus SYSTEM ADEIN ZX MALAYSIA ce Jp lee RG731BX Receiver Sold separately To measure main power pack voltage solder the sensor lead to the objective lines as shown in the figure below Using this method your battery pack does not need to be modified Note Polarity of the sensor wires is not important The sensor leads can be shortened as necessary Regulator ESC etc Note Be sure to insulate the sensor leads with heat shrink tube or insulation tape to avoid short circuits or the solder joints breaking with vibration
Download Pdf Manuals
Related Search