XB1-PC4 - JR PROPO
Contents
1. A IN N A ESC OQ Q2. TEL 06 6732 0200 9 00 13 00 14 00 17 30 XB1 PC4 45V 8 5V 17g XB1 P PC4 XB1 Pca XBus us ae PWM Con MADE IN JAPAN I I LED it ae XB1 PC4 th Hn r 1 ale ashe amar a 1XBus oe n Oi a E re J En 2 AR owe OOO O O XBUs PWM XB1 CPG XBus K XBus XBus Deans ultra
3. seats SX1 1ch ID1 1 SX2 1ch ID1 2 SX3 1ch ID1 3 SX4 1ch ID1 4 ID ID XG14 XB1 CPG ID XB1 CPG Ce CPG ae pe ID 1 4 ID ID XBus XBus
4. XBus XBus LED JR PROPO Wwww jrpropo co jp DMSS 2 4GHz Wr operati Operation Manual XBus SERIES XB1 PC4 XBus PWM converter Harness for XB1 CHB Thank you for purchasing this JR product To allow correct and safe use of this product please read this operation manual This product is only for use with JR XBus receivers XBUS About the XBus Logo This logo is only included on products that support the JR XBus System Features This product is the converter harness that allows the use of PWM servos with JR s XBus system It can be used at the channel ID of your choice Deans Ultra Plug type for strong power supply use Configuration XB1 PC4 Converter Main Unit Operation Manual this document Channel Label To allow safe use be certain to observe the following points In order to prevent injury to the operator or third parties or damage to property please observe the following A DANGER Not following this advice carries high risk of death or serious injury to the user or third parties
5. Do not use this product in the rain as water may cause electronic devices to malfunction Never disassemble or modify this product A WARNING Not following this advice may result in death or serious injury to the user or third parties Do not use this product in combination with other manufacturers products such as servos etc Do not use this product upon damage or slash on the Lead wire and or connector A CAUTION Not following this advice may cause injury to the user or third party or cause damage to property Before use check the following f the product used with a voltage other than the rated voltage it will cause damage to this product Be sure to connect properly between this product to servos receiver etc Make sure proper wiring for the Lead Harness Otherwise the Lead Harness may be damaged or broken Be sure the battery is fully charged before carrying out the setting Low battery may cause fail in setting This product may not be able to use Some ESCs Wif you have further questions please contact your local dealer or JR distributor in your country Specifications Item name XB1 CV1 XB1 CV4 Operating voltage 4 5V 8 5V Weight 17g Connection Diagram SX1 XB1 PC4 _ Krup m IB serii Bus communication System aan wl GP XB1 PC4 Left Up Connecto MADE IN JAPAN Whi Down i SX4 1 Checking LED Left Down ii DeansUlta XB1 P
6. C4main unit Connector for PWM servo it Connecter it mm ee ea E SE 1 1 XBus supporting receivers 1 i i XB1 CHB 1777777 1 Coldseparaty 1 Power ames Ma arty i Sold separatly ee Fe ga RXBattery Lead hamess Sold separatly 1 sold separately i This product converts the XBus signal to a PWM signal that then allows the use of normal PWM non XBus servos with JR s XBus system This product does not have an integrated regulator Please check the rated voltage of the target products and use the proper source battery for the receiver Channel ID setting for each output connector must be performed by either the Channel Programmer XB1 CPG or wirelessly from a JR transmitter fitted with XBus Be sure the white connector of this product is connected to the XBus port on the JR XBus receiver Power supply is not available from XBus connector Connect power supply to Deans Ultra Plug Use a power harness or a lead harness for cable extension Channel ID set up The default factory initial set up for each connector as supplied is as per the following SX1 Throttle 1ch ID1 1 SX2 Throttle 1ch ID1 2 SX3 Throttle 1ch ID1 3 SX4 Throttle 1ch ID1 4 Sub IDs are different at all Throttle channels Channel ID setting changing for each output connector must be performed by either the Channel Programmer XB1 CPG or wirelessly from a JR transmitter fitted w
7. JR PROPO www jrpropo co jp DMSS 2 4GHz XBus SERIES XB1 PC4 XBusPWM XB1 PC4 XB1 CHE JR x lt BuS XBus XBus JR XBus E XBus XB1 PC4 http www jrpropo co jp jon support REwor NEM C87A 577 0809 2 2 12 2013 07
8. ith XBus like XG14 If the IDs are wrongly set up please set up again by using the XB1 CPG or a JR transmitter fitted with XBus like XG14 During set up ID with XG1 CPG connect a RX battery to Deans Ultra Plug Please note that only JR XBus compatible transmitters can be used with this item Sub ID Up to 4 Sub ID can be set for each channel By giving independent Sub IDs individual setting can be carried out even for the servos connected to the same channel Operation check and confirmation Connect the connector white to the XBus port on a JR XBus receiver or directly to a XBus Hub and the connector s black to PWM servo s Upon receipt of proper signal from XBus the checking LED will light and signal output starts Make sure the servo s can be operated properly on the setting channel ID that you require
Download Pdf Manuals
Related Search