印刷までのプリンタ設定・確認事項 - mimaki engineering co., ltd.
Contents
1. haye A 4 1 5C 10 C 5 60 100cm ON2. UV 100 3 6 3 2 2 h 9 3
3. 2 z z tL CENTERS F 2 CENYER 2 2
4. fa E X z 50cm Printed in Japan D202374 10 01062012 MIMAKI ENGINEERING CO LTD 2012 IT J V400 SU V Series JV400 130 SUV JV400 160 SUV Perform test print to check that there is no line that is missing and no line that is bent Operation Manual Chapter2 Result is abnormal Perform head cleaning gt To Test Print Printer Setting and Checking Items before Printing When using JV400 SUV first turn the power supply ON and then perform check the items below before printing Refer to Operation Manual Chapter2 Set the media feeding amount Feed Correction Notes when using JV400 SUV m Do not leave the media for a long time more than ten minutes with the heater ON m Check the media float before detecting the media width E If paper jam occurred immediately perform head cleaning and check by test drawing E If dryness is not enough make the feeding speed slower or set the dryness time E Do not leave it wi
5. J V400 SU V Series JV400 130 SUV JV400 160 SUV 2 6 P JV400 SUV ON JV400 SUV E ON 10 eee BAS THERMS AHI AT 4 VORESHBTS 2 E OFF _ RT A E E E 2
6. etting a Media Operation Manual Chapter2 Lower the heater temperature If paper jam occurred If the head scratched the media or paper jam occurred immediately perform the items below After clamp up remove the clogging media Remove the Media If the head scratched the media reset the media Move the carriage to the waiting position and return it to the station with the key Z Refer to Operation Manual Chapter2 Setting a Media Detect the Media At the media detection if the head scratches the media or paper jam occurs perform head cleaning F Refer to Operation Manual Chapter2 Test Feeding Check that the media can be fed normally By referring to Operation Manual Chapter 2 Head Cleaning perform head cleaning Test Feeding Check that there is no media float between the Platen and the After heater Also check that there is no abnormality of feeding due to the media sticking to the platen Head Cleaning If there an abnormality Attach the antistatic sheet If you attach the of the media feeding antistatic sheet the drying performance will To Setting a Media Perform test print and check that there is no line that is missing and no line that is bent be lowered Operation Manual Chapter1 p g Test Print If nozzle missing In case that nozzle missing and no line that occurs is bent is not improved even though you Feed the media by 50cm and check that no media f
7. loat occurs at the media both edges and iE repeat cleaning by referring to Operation 5 Check of cockling between Clamp Clamp every time you feed the media Manual Chapter 4 When Nozzle Clogging To Head Cleaning If media cockling Clamp up once and reset the media Cannot Be Solved perform Washing of occurs Check that it is not skewed Head nozzle Set the temperature of the pre heater higher Print heater temperature 5 to 10 degrees Lower all heater temperatures by 5 degrees each It may not have been dehydrated enough Be careful about it To Setting a Media Feed the media that was deformed due to heating by about 60 to 100cm When you left it for a long time with the heater ON When the media extended to the utmost limit due to heating After the head recovered check the items below Check that the media is not skewed Check the media cockling Check that the head height that it is not too low Printed in Japan D202374 10 01062012 MIMAKI ENGINEERING CO LTD 2012 IT
8. th capping OFF and the cover opened E Leave the main power turned on to prevent ink clogging Refer to Operation Manual Correct the ink drop position for bidirectional printing Drop Position correct Referring to the print guide send the data to print gt ff a v Turning the Power ON Check that the output image has been dehydrated when it passes the UV lamp Checking dryness If it has not been Select more number of passes for the same dehydrated resolution When you perform the items menti Set the FEED SPEED lower lower than oned at the right the printing speed 100 Operation Manual Chapter3 lowers Therefore check whether Set the DRYING TIME for each scan you can raise the heater temperat A ure before performing them Operation Manual Chapter3 Set the heater and wait until it reaches the set temperature The setting value differs AOUE OAA GEGE depending on the media Refer to Operation Manual Chapter2 Preparing for the Heaters To Test Print Refer to Operation Manual Chapter2 Setting a Media Setting a Media Slightly hold the media with the media holder Print can be started Visually check the media float on the platen especially at the both edges of the media Check the media float When the media floats Strengthen the absorption fan Operation Manual Chapter3 For the roll media use the take up device To S
Download Pdf Manuals
Related Search