SS-PC1 - Roland
Contents
1. 11 1 1 UN 2009 SS PC1 tm 200 890mm 300mm e 1 41 mm2. A CS Ui 5 SS PC 1 SUPPORT STAND FOR PC 640mm 555mm 600 950 mm x Ha 3 5kg B4 tm 200 890mm 300mm 21 41 mm 4kg 2 1
3. Ce s CD ROM ieee 5 Jo O 3 2
4. d ace 2 3 1 2 5 1 0 0 0 0 5 0 6 2 0 2
5. Height 600 950 mm 23 5 8 37 7 16 inches height of mounting surface Includes the tripod Weight 3 5 kg 7 Ibs 12 oz Size of notebook computers that can be mounted Up to B4 size Width 200 390 mm 7 7 8 15 3 8 inches Depth upto300mm up to 11 13 16 inches Height 21 41 mm 7 8 1 5 8 inches not including screen lt may not be possible to mount some designs of notebook computer Weight capacity 4kg 8 lbs 14 oz In the interest of product improvement the specifications and or appearance of this unit are subject to change without prior notice 2 Attach the stoppers to the board 1 Remove the round nut attached to each stopper and insert the stoppers into the oblong holes in the board If you ll be mounting a thin notebook computer on the stand remove the upper round nuts as well e Remove the round nut ace 2 Temporarily fasten to the board by lightly tightening the lower round nut that you removed 3 Adjust the direction of the legs and the height and direction of the board 1 Place the tripod legs so that they will not be in your way 2 Loosen the height adjustment knob Set the board at the desired height and direction and firmly tighten the height adjustment knob If you need to change the height use your hand to support the board from below so that it does not drop down and then loosen the height adjustment knob Roland support sTAND FOR PC SB te
6. it in place If the height is inappropriate your notebook computer may slide out from the stoppers or the portion held by the stoppers may break Please use caution Depending on the design of your notebook computer the stoppers may prevent you from inserting the power plug connectors or CD ROM discs If so adjust the location at which your computer is fastened If the stopper is too close to your notebook computer the round nut may scratch your computer Please use caution To avoid damaging your notebook computer do not fold down its screen while the computer is still held by the stoppers To prevent your notebook computer from falling do not move it or adjust the height while it is still on the stand 3 Use two bolts washers and knobs to attach the tripod as shown in the illustration below As shown in the illustration below insert the bolts in alternate directions with the small knob below Angle adjustment knob Db mmm Small knob 9 DE Make sure that there are no gaps at the locations shown in the illustration below 4 Fully extend the tripod and tighten the tripod knob Be careful not to pinch your fingers when extending the tripod Do not remove the tripod knob Extend it all the way to the ring 5 Place the tripod upright Specifications SS PC1 SUPPORT STAND FOR PC Dimensions Width 640 mm 25 1 4 inches Depth 555mm 21 7 8 inches
7. s 4kg CD ROM SS PC 1 1 1 2 X 2
8. 1 5 8 inches e Weight up to4kg up to 8 lbs 14 oz Roland will not be liable for any damage that may occur to an item placed on the stand if the stand falls over nor for any consequential damage that may occur Loosen the round nut to adjust the height Leave a bit of space 2 Adjust the angle of the board As an example here s how to attach a notebook computer to the stand Attaching a notebook computer may not be possible to mount some designs of notebook computer The location of the CD ROM drive or other disc insertion slot will depend on the design of your notebook computer Insert the disc you re using into your computer before attaching the computer 1 Loosen the angle adjustment knob and set to the SS PC1 the angle as desired You can tilt the board in a range of 5 from the 1 Place your notebook computer on the board horizontal position 1 Loosen the two stoppers and place your notebook computer as close to the center as possible 3 Use cable ties to bundle any connected cables and fasten them to the stand 2 Firmly tighten the angle adjustment knob If you ll be using a mouse place the computer as close to the center as possible while still allowing space for yourself to operate the mouse 2 Open the screen of your notebook computer adjust the height of each stopper by loosening the round nut appropriately for the thickness of your computer and then fasten
9. Owner s Manual Roland es SS PC1 Before using this unit carefully read the sections entitled USING THE UNIT SAFELY and IMPORTANT NOTES separate document These sections provide important information concerning the proper operation of the unit Additionally in order to feel assured that you have gained a good grasp of every feature provided by your new unit Owner s Manual should be read in its entirety The manual should be saved and kept on hand as a convenient reference Check the included items Board Bolt Washer gt N Mei Small knob Bolt Angle adjustment knob 178 Stoppers Round nuts Cable ties Tripod knob Height adjustment knob How it should look when assembled below and insert the tripod At T p Copyright 2009 ROLAND CORPORATION All rights reserved No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION Assembly 1 Attach the tripod to the board 1 Remove the angle adjustment knob the small knob and the washers and bolts from the upper portion of the tripod Do not remove the height adjustment knob or the tripod knob 2 Pla ce the board as shown in the illustration Installation The SS PC1 can support an item within the following ranges of width depth height and weight e Width 200 390 mm 7 7 8 15 3 8 inches Depth upto300mm up to 11 13 16 inches e Height 21 41 mm 7 8
Download Pdf Manuals
Related Search