取扱説明書 INSTRUCTION MANUAL - KYOCERA Connector Products
Contents
1. The product is designed thinner for the purpose of downsizing and weight saving Therefore do not mate them with applying uneven pressureorinadistorted way or the insulator housing may be damage contacts may be deformed and or tails may be unsoldered Attachment in a distorted way Engagement with Engagement wit Uneven pressure uneven pressure 0O Engagement by inserting from the tail side SERIES 8041 INSTRUCTION MANUAL SPEC No 205 03 263 106 03 004 PAGE 5 11 KYOCERA ConnectorProductsCorporation 3 3 Disengagement It is recommended to use the disangaging jig to disengage the connectors If it2. If something touches the contacting points or foreign matters are put inside the mating space in receptacle connectors the spring could be deformed Contacting point Receptacle Connector Contacting point Plug Connector Hamess PLUG Please take particular note of plug connectors for contacting Darts are exposed on plug connectors 2 REC X Y To mate the connectors place the plug on the receptacle and align their position by slightly moving the plug connector in directions of XandY Mate them while the top face of the plug connector is kept horizontal XX direction Y Y direction wi lt X Y X direction Y direction SPEC No 205 03 263 PAGE 4 11 SERIES 8041 INSTRUCTION MANUAL 106 03 004 KYOCERA ConnectorProductsCorporation 3
3. Please make sure that the product is free from deformity caused by the unnecessary stress applied to the contacting points and the tails 2 Please do not apply flux onto the tails and a PC board in manual soldering Splattered or migrated flux inside the connector or to the contacting points may cause a contact failure Also avoid giving any stress to the contacts with the soldering iron It could deform the tails or melt the insulator Solderng iron fP a Board SERIES 8041 INSTRUCTION MANUAL SPEC No 205 03 263 106 03 004 PAGE 3 11 KYOCERA ConnectorProductsCorporation 3 2 Engagement 1 REC
4. SPEC NUMBER 205 03 263 KCERd KYOCERA Connector Products Corporation INSTRUCTION MANUAL SERIES 8041 WIRE TO BOARD CONNECTOR H 0 9 mm O EDN 418 6 07 12 H Kurimoto H Nakamura Rev EDN DCN No Date Prepared Checked Approved 106 03 003 KYOCERA ConnectorProductsCorporation Table of Contents 1 EE Preface So 2 2 Part GS 2 3 Gautions in using 0 3 SERIES 8041 INSTRUCTION MANUAL SPEC No 205 03 263 106 03 004 PAGE 1 11 KYOCERA ConnectorProductsCorporation 1 Preface 8041 Series 8040 is a MICRO WIRE to BOARD connector developed to meet the market s demand for the higher mountability 2 Part names SERIES 8041 WIRE TO BORD CONNECTOR H 0 9mm Plug Receptacle Connector Mating Condition SERIES 8041 INSTRUCTION MANUAL SPEC No 205 03 263 106 03 004 PAGE 2 11 KYOCERA ConnectorProductsCorporation 3 Cautions in using 3 1 For surface mounting 1
5. is Impossible to use the jig because of space Iimitations due to other surrounding components apply disengagement with wires or direct disengagement described below 1 Disengagement by using the jig REC Hold the plug connector with the jig and pull it straight upward Do not distort or slant the connector Pay attention to hold the plug connector only if the receptacle connector is held together tails may be unsoldered SERIES 8041 INSTRUCTION MANUAL SPEC No 205 03 263 106 03 004 PAGE 6 11 KYOCERA ConnectorProductsCorporation Disengaging jig The shape in detail may be subject to change with
6. that the receptacle connector is mounted on an FPC pay enough attention to cause no flexure on FPC when disengaging them The connector could flex with the FPC and it may be broken Make sure to hold the two points on the FPC as shown below when disengaging the connectors Disengaging Disengaging Hold down Hold down wy S FPC lt Disengaging by holding the FPC Disengaging by holding no FPC SERIES 8041 INSTRUCTION MANUAL SPEC No 205 03 263 106 03 004 PAGE 10 11 KYOCERA ConnectorProductsCorporation 5 The product is designed thinner for the purpose of downsizing and weight saving Therefore do not disengage them with applying uneven pressure or ina distorted way or the insulator housing may be damage contacts may be deformed and or tails may be unsoldered Detachment in a distorted way S I Tk Disengagement with u
7. N MANUAL SPEC No 205 03 263 106 03 004 PAGE 8 11 KYOCERA ConnectorProductsCorporation 3 Direct disengagement by manipulating the plug connector Hook such as the tweezer tip in the concave part of the plug connector or the wire and push it up to disengage the plug connector Do not touch tails at all or connector may be damaged and or contacts may be deformed SERIES 8041 INSTRUCTION MANUAL SPEC No 205 03 263 106 03 004 PAGE 9 11 KYOCERA ConnectorProductsCorporation 4 REC FPC FPC FPC 2 In the case
8. neven pressure applied on tails SERIES 8041 INSTRUCTION MANUAL SPEC No 205 03 263 106 03 004 PAGE 11 11
9. out notice Please inquire for details Shape of tip end For reference holding by ji9 1 7 Plug Connector Dimension SERIES 8041 INSTRUCTION MANUAL SPEC No 205 03 263 106 03 004 PAGE 7 11 KYOCERA ConnectorProductsCorporation 2 Disengagement with wires by pulling wires 2 Z X Hold the two wires and pull them straight upward in the Z direction to disengage the connectors Do not pull them upward violently Also do not pull them in the directions of X or Y Please make sure that nothing wrong occurred on the pressure welded part after the wires are removed Z Z direction X X direction Y Y direction SERIES 8041 INSTRUCTIO
Download Pdf Manuals
Related Search