Home
0901135_BA_PolyFlex DPM 800 V4.0-A4
Contents
1. Exit ein Schritt zur ck Men punkt w hlen ausw hlen best tigen Werte eingeben Bild 12 Fernbedienung Hinweis Die Tastenfunktionen werden auch am un teren Rand der Bildschirmanzeige angezeigt Aufgrund der IR bertragung sollte die Fernbe dienung bei der Programmierung auf die IR Schnittstelle im Grundger t gerichtet sein POLYTRIN 4 2 Programming of modules After assembly of the base unit and construction of the entrance distribution programming of the mod ules to the desired output channels takes place at each module Note LED red service mode active LED green program found LED flashing green no program found Note Only one module may be switched to pro gramming mode at the same time Modulators are set by the programming of the corre sponding digital modules Twin modulators are set by the first digital module because the output channels are adjacent channel operating 4 2 1 Remote Control Function of keys menu change Exit one step back choose menu item change values choose confirm enter values Figure 12 Remote Control Note The key functions are also shown on the lower part of the on screen display Due to the IR transmission the remote control should be directed to the IR interface in the base unit 15 Bild 13 POLYTR N 4 2 2 Master Module DPM PS und DPM PT Module type 4 2 2 Master Module DVB S Master Software version V 1 09 Serv
2. mon Kir B G annet a lt gt Chane 6 input inl CAM Menu Slave Select Output Settings al Frequency 412692 MH2 LNB LO freq 10600 MHz Symbol Rate 22000 KS s Auto OK TV Standard B G Channel iC 21 lt gt Frequency 471 25 MHz Audio Mode Auto TS lt gt 0 db Screen Type OFF P S Ratio 16 dB Search Audlo Level lt gt L angunge man lt gt Subtitle NONE Programmierfenster ME Master Modul TV oder Messger t am Ausgang anschlie en einschalten und Kanal 69 einstellen Figure 15 CHANNEL Setup Window 1 Connect the TV or measuring instrument at the output turn it on and adjust channel 69 Basisger t PolyFlex einschalten 2 Turn on base unit PolyFlex Den SETUP Schalter des zu programmierenden 3 Turn the switch of the module to be programmed Moduls nach oben auf SETUP schalten LED up to position SETUP LED lights red rot Am Monitor erscheint das oben angezeigte Pro 4 The above indicated programming window ap grammierfenster mit Angabe von Modultyp Software Version und Servicekanal Hinweis Das jeweils einzustellende Feld ist far big markiert Der Eingabebereich Input Settings ist markiert Die Taste OK der Fernbedienung dr cken das Feld Frequency ist markiert Jetzt die Frequenz des gew nschten Transpon ders eingeben Mit der Taste CHW auf LNB LO Freq und da nach auf Symbol Rate springe
3. Blockschaltbild herstellen gt Bei Ausgangsverst rkern ohne DC Speisung die graue Leitung der Stromversorgung des FM Verst rkers am 12 V Anschluss anl ten Ausgangssammelfeld Output Combiner Nicht angeschlossen Testausgang Ausgang Test Output Output 2 5 Modul DPM FM The module DPM FM is used for connecting the broadcast FM range The module is switched be tween output combiner and output amplifier It is sup plied with current over a connection of the output amplifier situated in the headend A FM signal can be fed in at the FM input of the module For the suppression of disturbing or not de sired transmitters two traps stand at the disposal The two traps can be adjusted individually when required In the delivering condition the two traps are tuned outside the lower band limit and are therefore not ef fective For the adjustment of the FM level the mod ule contains a variable attenuator The socket lying left beside the FM input socket is not connected It only serves for the mechanical fas tening of the module in the basic unit Installation gt Putting the two F connectors of the DPM FM module into the holes over the output amplifier and screwing it tight from the outside with union nuts gt Making Interwiring between output combiner out put amplifier and FM amplifier in accordance with the block circuit diagram below gt At output amplifiers without DC feeding solder t
4. dio video signals AV Slave modules are for the processing of au dio video signals controlled by an AV Master mod ule Setup Schalter Switch Figure 4Switches and connections of the AV master module Video IN Audio Level L Audio L IN Audio Level R Audio R IM Figure 5 Switches and connections of the AV slave module POLYTR N 2 5 Modul DPM FM Das DPM FM Modul dient zum Einschleifen des Rundfunk FM Bereiches Das Modul wird zwischen Ausgangssammelfeld und Ausgangsverst rker ge schaltet Es wird ber einen Anschluss des im Ge r t befindlichen Ausgangsverst rkers mit Strom versorgt Am FM Eingang des Moduls kann ein FM Signal ein gespeist werden Zur Unterdr ckung von St r oder nicht gew nschten Sendern stehen zwei Fallen zur Verf gung Die beiden Fallen k nnen bei Bedarf indi viduell abgeglichen werden Im Auslieferzustand sind die beiden Fallen au erhalb der unteren Bandgrenze abgeglichen und sind deshalb nicht wirksam Zur An passung des FM Pegels enth lt das Modul einen Pe gelsteller Die links neben der FM Eingangsbuchse liegende Buchse ist nicht beschaltet Sie dient nur zur mecha nischen Befestigung des Moduls in der Grundeinheit Einbau gt DPM FM Modul mit den beiden F Steckern in die L cher ber dem Ausgangsverst rker stecken und von au en mit Uberwurfmuttern festschrau ben gt Kabelverbindung zwischen Ausgangssammelfeld Ausgangsverst rker und FM Verst rker gem
5. Anschluss Connection Anschluss Connection LNB Versorgung LNB Supply Frequenzbereich Frequency range Eingangspegel Input level Modulation Modulation Bandbreite Bandwidth 7 8 MHz Abstimmung ber Frequenz Tuning by frequency 250 kHz Schritte steps FEC gem DVB in accordance with DVB Code Rate auto Code rate auto 1 2 2 3 3 4 5 6 7 8 berwachungs Intervall Guard interval 1 4 1 8 1 16 1 32 IEC Buchse female 75 O IEC Stecker male 75 Q 5 VDC max 100mA _ schaltbar switchable 147 230 470 862 MHz 50 70 dBuV COFDM 2k 8k DVB Standard gemaB in accordance with ISO IEC 13818 2 gemaB in accordance with ISO IEC 13818 3 32 44 1 48 kHz Demux Video Decodierung decoding Audio Decodierung decoding Abfragegeschwindigkeit Sampling Rate AV Ausgang AV Output Anschluss Connection Videopegel Video level Video Bandbreite Video bandwidth Video S N Audiopegel Audio level Audio Bandbreite Audio bandwidth Audio S N Schnittstelle Interface Steckerleiste Buchse Edge card connector male 1 Vpp 75 0 20 Hz 5 MHz gt 60 dB 1 Vp 10 KQ 3 dB Schritte steps 6 dB 6 dB 40 Hz 15 kHz gt 50 dB Steckerleiste Buchse Edge card connector male Transportstrom Ausgang Transport Stream output gem DVB in accordance with DVB Entschl sselung Descrambling Common Interface Common Interface Umweltbedingungen Environment conditions Betriebst
6. appending master module With the Slave module it s only possible to receive those programs of the transponder which has been selected for the master module Due to this the adjustment possibilities of the Slave module are limited Carry out step 1 to 4 for programming the master module Press the button CHW of the remote control the field OK of Channel Search is highlighted now Press the button OK The Slave module starts scanning of the incoming signals and lists all found programs 21 POLYTR N CHANNEL Setup Transponder Channels ZDF ZDFinfokanal ZDFdokukanal fy Yes RID ZDFtheaterkanal Audio PID 3sat Langusige KiKa DKULTUR Subtitle Bild 19 CHANNEL Setup Fenster Slave 22 Mit den Tasten 4 V ein Programm aus der ange zeigten Liste markieren Mit der Taste MENU in das Feld Transponder springen und falls vorhanden die gew nschte Sprache in den Feldern Language und Subtitle einstellen Mit der Taste OK die Einstellungen speichern Der Cursor springt auf das Feld Output Settings des ersten Fensters zur ck Jetzt werden die gew nschten Daten des Modu lators eingestellt und durch Dr cken der Taste OK gespeichert Die Programmierung ist abge schlossen Jetzt den Schalter SETUP wieder auf OFF nach unten stellen die LED leuchtet wie der gr n Nun kann das n chste Modul in sinn gem gleicher Weise programmiert werden Figure 19 CHANNEL Setup Window Slave Mark a progr
7. wahl der Update Daten Der Experten Modus ist Passwort gesch tzt Details bez glich dieses Modus erhalten Sie auf Anfrage von unseren Service Abteilung POLYTRN The digital modules of the PolyFlex can be updated by the RS232 interface 5 Software Update Needed auxiliary PC with operating system XP or Vista and serial interface Polytron Update Software i e DVB Update_V201 zip serial RS232 Cable 5 1 Software Update procedure 1 Unzip the software package and install update software by starting Setup exe program 2 Start Software Flex Update Utility V201 exe 3 Choose available COM port from control bar on ly first time 4 Disconnect main from base unit PolyFlex power off 5 Connect COM port with RS232 socket on the main board using a RS232 cable 6 Connect main to the base unit again power on 7 Turn setup switch to the service mode SET LED colour changes to red Note Only one module should be in the pro gramming mode simultaneously 8 Start Update procedure by selecting the Update icon in the tool bar The module type will be identified and updated automatically A blue bar shows the progress of the Update procedure During the update procedure please avoid to open other programs to disconnect the headend to disconnect the computer to interrupt the update procedure to move the update window 9 An Update successful message is shown in case of successful
8. 2 12 Telefax 49 0 70 81 1702 50 Internet http www polytron de eMail info polytron de Technische nderungen vorbehalten Subject to change without prior notice Copyright Polytron Vertrieb GmbH
9. D menu navigation is shown on service channel C69 855 25 MHz Note Only one module may be in the programming mode By the RS 232 interface of the base plate a software update of the modules is possible P amp Leiste zum Einbau eines Verteilers for installation of a splitter i Digitalmodulsteck platz Diaital Module Slot Netzteil Power Supply Verteiler optional Splitter optional KANAL et LiL Steckplatzbeschriftung Labeling of the Module Slots RS232 Schnittstelle Nez Interface Twin Ot 2A4 104 a S Erdungsschraube NN Screw TETA YS R Output SS SEER ae Steckplatz Stereo Coder Slot Ausgangssammelfeld Output combiner Figure 1 PolyFlex Interior view 2 2 Mastermodule DPM PS PSI PS Conax CryptoWorks DPM PS ME DPM PT PTI PT ME Bei den Modulen DPM PS Master handelt es sich um DVB S Empfangsmodule zur Umsetzung von QPSK modulierten Programmen in AV Signale Die Module DPM PS ME PSI PS CryptoWorks und PS Conax bieten zus tzlich die M glichkeit verschl sselte Pro gramme aufzubereiten Bei den PSI Modulen ist ein CAM Modul erforderlich Bei den PS CryptoWorks und PS conax Modulen ist die entsprechende Ent schl sselung integriert Das Modul DPM PS ME ent schl sselt mehrere verschl sselte Programme gleichzeitig und stellt diese den folgenden Slave Modulen ber den Datenstrom zur Verf gung Bei den Mod
10. D programming technology switch for LNB voltage on each Master Module high output level 100 dBuV continuous output frequency range 47 862 MHz gt integrated output combiner amplifier and power supply unit gt test output 20 dB VV VV VV WV Depending on the inserted module the TV Standards B G B B DIK I M N and L can be adjusted The base unit disposes of eight module slots and enables the conversion of up to eight programs Like all Polytron headends the DPM integrates an output collecting field an amplifier and a power supply unit All entrances have switches for remote supply for the LNB s Attached with eight channels the output level of the headend is 100 dBuV A test output with 20 dB reduced output level is available for measurements and service The Master Module is equipped with a tuner for the reception of the desired transponder Should several programs from one transponder be converted Slave Modules are used The MPEG data stream pro cessed by the master module is passed to the Slave Modules Therefore it is possible to process eight programs from one transponder with only one single Master Module and seven Slave Modules Afterwards the processed A V signals are passed to the pluggable modulators The Polytron series offers single and twin modulators The channels of the twinmodulators are compulsory adjacent channel op erating e g channel 21 and 22 Pay attention to the labelling of the modul
11. Modula tor aus der DPM Serie der ber das Motherboard mit dem eingesetzten Digitalmodul verbunden ist in ei nen TV Kanal gewandelt Am Slave Modul befindet sich ein SETUP Schalter zum Aktivieren des Programmiermodus Bild3 Bedienelemente und Anschl sse am Slave Modul 2 3 Slave module DPM SL The Slave modules DPM SL receive the data stream from the master module and don t need an integrated tuner From this data stream a channel is selected and converted into an analogue AV signal Therefore with a Slave module only one channel of the tran sponder on which the master module is pro grammed can be selected Afterwards the AV signal is converted into a TV channel by a modulator from the DPM series Via the motherboard the modulator is connected with the in serted digital module A SETUP switch is located at the Slave module for activating the programming mode Setup Schalter Setup switch Figure 3 Switches and connections of the slave module 2 4 Modul DPM AV Die DPM AV Master Module dienen zur Aufberei tung von Audio Video Signalen Die AV Slave Module dienen zur Aufbereitung von Audio Video Signalen gesteuert von einem AV Master Modul Bild 4 Bedienelemente und Anschl sse am AV Master Modul Bild5 Bedienelemente und Anschl sse am AV Slave Modul Video IN Audio Level L Audio L IN Audio Level R Audio R IM POLYTRIGN 2 4 Module DPM AV The DPM AV modules are for the processing of au
12. POLYTREN PolyFlex Ko pfstelle PolyFlex Headend DPM 10001010100101010 01100100111101010 00010011001 10011101 09D teat 9110 910110000000100110 1010101100000001001 au 1010100 ee 1101001 11 ly 500000D00000000T R to 441010001 00 511001110 001010 ss oot ao 8 Bedienungsanleitung User manual 0901135 V4 0 POLYTR N Inhaltsverzeichnis Table of contents No OF FP ODO N HINWEIS Der Inhalt dieses Firmenhandbuches ist urheberrechtlich geschutzt und darf ohne Genehmigung des Verfassers weder ganz noch teil weise in irgendeiner Form vervielfaltigt oder kopiert werden Ande rungen in diesem Firmenhandbuch die ohne Zustimmung des Ver fassers erfolgen k nnen zum Verlust der Gew hrleistung bzw zur Ablehnung der Produkthaftung seitens des Herstellers f hren F r Verbesserungsvorschl ge ist der Verfasser dankbar Verfasser Polytron Vertrieb GmbH Postfach 10 02 33 75313 Bad Wildbad Germany Unten stehende Hervorhebungen werden in diesem Handbuch mit folgenden Bedeutungen verwendet HINWEIS gilt f r technische Erfordernisse die der Benutzer der Ger te besonders beachten muss um eine einwandfreie Funktion der Ger te Anlage zu ge w hrleisten ACHTUNG bezieht sich auf Anweisungen die genau einzuhal ten sind um eine Besch digung oder Zerst rung des Ger tes zu vermeiden VORSICHT steht f r Anweisungen deren Nichtbeachtung eine Gef hrdung von Personen nich
13. am from the indicated list by keys AY Jump into the field Transponder with the button MENU set the desired language to the fields Language and Subtitle if available Save adjustment with the button OK The Cursor jumps back to field Output Settings of the first window Now set the desired data of the modulator and save them by pressing the button OK The pro gramming is finished now Set the switch SETUP downward on OFF again the LED lights green again The next module can be programmed in the analogously way now POLYTR N 4 2 5 Master Modul DPM AV 4 2 5 Master Module DPM AV Module type AV Master Software version S 1 02 service channel C60 865 25 MHz Modulators Output Settings TV Standard B G lt gt ot Twin Stereo B G B Channel C 21 lt gt Fraquency 471 26 MHz Audio Mode Stereo lt gt P S Ratio 16 dB Bild 20 Programmierfenster 1 Master und 1 Slave Figure 20 Programming window 1 Master and 1 Modul mit Twinmodulatoren Slave Module with twin modulators Moduletype AV Master Software version 5 1 02 Service channel C69 855 26 MHz Modulators Output Settings TV Standard B G 51 Stereo B G Channel Cc 21 S 2 Stereo B G Frequency 471 26 Audio Mode Stereo P S Ratio 16 dB Bild 21 Programmierfenster 1 Master und 2 Sla Figure 21 Programming window 1 Master and 2 veModule mit Singlemodulatoren Slave modules with Single modulators Anschluss und Einste
14. ancel PIygure IT UTTAININCL OGLUD WIIIUUW 9 Mark a program from the indicated list by keys AV Jump into the field Transponder with the button MENU set the fields Language Subtitle and teletext to your requirements Save the adjustment with the button OK 10 The Cursor jumps back to the field Channel A of the first window 11 With OK gt Output Settings gt OK the desired data for adjustment of the modulator are set similarly to Input Settings and have to be saved by pressing the button OK 12 Are twin modulators used look at step 14 13 The programming is completed Now set the switch SETUP downward on OFF the LED lights green The next module can be programmed in the analogously way 14 By using twin modulators select on the top menu Channel B Push the button OK shown at the display and set the switch of the second input module to SETUP Both LNBs lights now red 15 Set the input parameters like descripted at step 6 There are no settings for the output channel this will be automatically set one channel higher than channel A For example Channel A C21 so channel B will be automatically C 22 16 Set the switch after programing to OFF LED lights green 17 POLYTR N 4 2 3 ME Master Module Bild 15 l 18 4 2 3 ME Master Modules DPM PS ME und DPM PT ME DPM PS ME and DPM PT ME DVB S Master ME Software hited el V 1 09 C69 855 25 MHz Module type Service channel
15. ave module If not go to 16 19 POLYTR N Module type DVB S Master ME Software version V 1 09 Service channel C69 855 25 MHz Twin Stereo B G Channel A MEEA Input Settings CAM Menu E Sta Master ORF1 Max 03 Slaves possible IN I SL01 ORF2 8L02 ATV 005 ORF2 B 1 L03 ORF2 W 006 ORF2 O 007 ORF2 S 008 ORF2 T YAI Move LT Swich LOKI Select EXT Stora Bild 17 Slave Select Fenster Figure 17 Slave Select window 13 Auf der rechten Seite wird nun die Anzahl der 13 On the right side the maximum quantity of the max m glichen von dem CAM und Karte zu decryptable channels by the used CAM and card entschl sselten Programme angezeigt is shown Im Beispielbild Max 03 Slaves possible See example figure 17 Max 03 Slaves possible 14 Die gew nschten im Beispiel max 3 Program 14 Chose the channels to be decrypted Program me die entschl sselt werden sollen ausw hlen the corresponding Slave Moduls as indicated in Die entsprechenden Slave Module wie im fol the next chapter genden Abschnitt erkl rt programmieren 15 Bei der Verwendung von Twinmodulatoren wird 15 Whenever programming twin modulators path B nun der Kanalzug B in sinngem gleicher can be programmed in the analogously way Weise programmiert 16 Die Programmierung ist abgeschlossen Jetzt den 16 The programming is completed Now set the Schalter SETUP wieder auf OFF nach unten switch SETUP d
16. bove or in the immediate vicinity of heat sources e g heating ele ments heating systems or similarly where the equipment is exposed to heat radiation or oil vapour Due to the risk of fire by overheating or lightning strike it is recommendable to install the equipment on a non combustible base Fuses Fuses should be changed only from authorized tech nical personnel Only fuses of the same type may be used POLYTR N ACHTUNG Diese Baugruppe enth lt ESD Bauteile ESD Elektrostatisch empfindliches Bauteil Eine elektrostatische Entladung ist ein elektrischer Stromimpuls der ausgel st durch gro e Span nungsdifferenz auch ber ein normalerweise elektrisch isolierendes Material flie en kann Um die Zuverl ssigkeit von ESD Baugruppen ge w hrleisten zu k nnen ist es notwendig beim Um gang die wichtigsten Handhabungsregeln zu beach ten gt Elektrostatisch empfindliche Baugruppen d rfen nur an elektrostatisch gesch tzten Arbeitspl tzen EPA verarbeitet werden gt Auf st ndigen Potentialausgleich achten gt Personenerdung ber Handgelenk und Schu herdung sicherstellen gt Elektrostatisch aufladbare Materialien wie norma les PE PVC Styropor etc vermeiden gt Elektrostatische Felder gt 100 V cm vermeiden gt Nur gekennzeichnete und definierte Verpa ckungs und Transportmaterialien einsetzen Sch den durch fehlerhaften Anschluss und oder unsachgem e Handhabung sind von j
17. brackets 3 Master Modul Master module 5 Slave Modul Slave module 1 2 3 4 Befestigungswinkel Mounting brackets 5 6 Verteilerleiste Splitter strip 7 7 Masseschiene Ground rail Digital Modul DD OQ OW DD 0 7 D 2 Figure 11 0 1 2 3 Connect the HF entries with the appropriate HF cables Connect the device with the accompanying net work cable to the network Program modules according to chapter 4 2 Place the lid on the housing and tighten 6 f Digital Digital dul Modul PolyFlex Assembly Schrauben Bolts ErdungsanschluB Grounding connector Ausgangssammelfeld Output combiner Stereocoder Steckplatz Stereocoder slot HF Ausgangskabel RF output cable Pegelsteller Attenuator AuBenseite outside 4 2 Programmierung der Module Nach der Best ckung der Grundeinheit und dem Aufbau der Eingangsverteilung erfolgt die Program mierung der Module auf die gew nschten Ausgangs Kan le Hinweis LED rot Servicemodus aktiviert LED gr n Programm gefunden LED gr n blinkend kein Programm ge funden Hinweis Es darf sich immer nur ein Modul im Programmiermodus befinden Die Einstellung der Modulatoren erfolgt ber die Pro grammierung der dazugeh rigen Digitalmodule Bei Twinmodulatoren erfolgt die Einstellung ber das ers te Digitalmodul da die Ausgangskan le zwangsbe nachbart sind 4 2 1 Fernbedienung Tastenfunktion
18. dem Innenleiter keinen Kurzschluss bildet 3 3 Fitting F Connectors Screw the F connector onto the stripped co axial cable e g IK 16 Take care that the shielding and the inner core may not form a short circuit Bild 9 Koaxialkabel konfektionie Figure 9 Assembling coaxial cables ren 3 4 Abnehmen des Gehauseoberteils 3 4 Remove the housing lid Die beiden Kreuzschlitzschrauben Bild 4 1 auf dem Unscrew the two cross head screws Figure 4 1 of Gehauseoberteil l sen und dieses vorsichtig abneh the housing lid and remove it carefully men Bild 10 Geh use ffnen Figure 10 Open housing 12 4 Inbetriebnahme 4 1 Einbau der Module gt Montageuntergrund gem der Beschreibung auf der beiliegenden Bohrschablone vorbereiten Die beiden Kreuzschlitzschrauben Bild 11 8 der Masseschiene Bild 11 7 l sen und diese nach unten herausziehen Gegebenenfalls CAM Modul und Smart Cards in die entsprechenden Master Module einsetzen Das erste Master Modul Bild 11 3 in den ersten Steckplatz links einstecken und mit seinem Be festigungswinkel Bild 11 2 an der Leiste Bild 11 6 festschrauben Das dazugeh rige HF Kabel Bild 11 1 am Mo dul und am HF Eingang des Geh uses anschlie Ben Anschlie end die gew nschten Slave Module Bild 11 5 einstecken und mit ihren Befesti gungswinkeln Bild 11 4 an der Leiste Bild 11 6 festschrauben Weitere Master oder Slave Module in gleicher Weise einbauen und an
19. dule slot no Empfangsart reception mode Satellit satellite Polarisation polarisation Frequenz frequency Programm program Sprache Language Ausgangkanali output channel PolyFlex Digitalmodule digital modules Modulatoren modulators terrest Sat horiz verti DVB T Master DVB S Master single twin mono stereo multi norm 2 terrest sat horiz verti DVB T Master DVB S Master Slave single mono stereo multi norm 3 terrest sat horiz verti DVB T Master DVB S Master Slave single twin mono stereo multi norm 4 terrest sat horiz verti DVB T Master DVB S Master Slave single mono stereo multi norm 5 terrest sat horiz verti DVB T Master DVB S Master Slave single twin mono stereo multi norm 6 terrest sat horiz verti DVB T Master DVB S Master Slave single mono stereo multi norm 7 terrest sat horiz verti DVB T Master DVB S Master Slave single twin mono stereo multi norm 8 terrest Sat horiz verti DVB T Master DVB S Master Slave single mono stereo multi norm POLYTRIN Polytron Vertrieb GmbH Postfach 10 02 33 75313 Bad Wildbad Zentrale Bestellannahme H Q Order department 49 0 70 81 1702 O Technische Hotline Technical hotline 49 0 70 81 170
20. e module and the HF entry of the cas ing Subsequently plug the desired Slave Modules Figure 11 5 in and screw it down with the mounting brackets Figure 11 4 to the strip Fig ure 11 6 Attach and connect additional Master or Slave Modules in the same way Now install the modulators Figure 11 13 With the stereo modulators the corresponding stereo coders have to be set in the accordant slot direc tion doesn t matter With the mono modulators the audio bridges have to be set Picture 10 11 Using twinmodulators it is necessary to in sert the two stereocoders or audio bridges Connect the modulators Figure 11 13 over the HF cables Figure 11 12 with the output combin er Figure 11 10 Set the mass rail on top Figure 11 7 and slide the slits which are on both sides under the screws Picture 10 8 and tighten them Thereby aligning the modules in a way that it is locked into the slits of the mass rail Hook the unit in the prepared bolts and screw in the lower bolts Attach the grounding cable with the grounding screw Figure 11 9 to the casing 13 POLYTR N Bild 11 14 HF Eing nge mit den entsprechenden HF Kabeln verbinden Ger t mit dem dazugeh rigen Netzverbindungs kabel mit dem Netz verbinden Module gem Abschnitt 4 2 programmieren Geh useoberteil aufsetzen und festschrauben PolyFlex Montage 1 HF Eingangskabel RF input cable 2 Befestigungswinkel Mounting
21. e slots on the base plate when assembling the base unit When twin modula tors are used they have to be inserted into the odd numbered module slots 1 3 5 7 the adjacent module slot stay empty However when assemling stereocoders both module slots are filled POLYTR JN Die Digital Module besitzen einen Schalter um den Programmiermodus Setup zu aktivieren Die Mas ter Module besitzen einen weiteren Schalter zum Ak tivieren der LNB Fernspeisspannung Die Programmierung der Module erfolgt per Fernbe dienung Nach Aktivierung des Programmiermodus wird auf dem Service Kanal C69 855 25 MHz die benutzerfreundliche Men f hrung auf dem Bildschirm OSD angezeigt Hinweis Es darf sich immer nur ein Modul im Pro grammiermodus befinden ber die RS 232 Schnittstelle der Grundplatte ist ein Software Update der Module m glich Mastermodul Slavemodul Master Module Slave Module amp s gt ele et wp eeewee Singlemodulator Single modulator Twinmodulator Twin modulator Bild 1 Stereocoder Stereo coder PolyFlex Innenansicht I Q Ga N 4 BY A w MN MN o RAE The digital modules are equipped with a switch to ac tivate the programming mode Set up The master modules have a second switch to activate the LNB remote feeding voltage The programming of the modules takes place by remote control When acti vating the programming mode the user friendly on screen OS
22. ection Steckerleiste Stecker Edge card connector male Videopegel Video level 1 Vop 75 O Video Bandbreite Video bandwidth 20 Hz 5 MHz Audiopegel Audio level 1 Vp 10 KQ 3 dB Schritte steps 6 dB 6 dB Audio Bandbreite Audio bandwidth 40 Hz 15 kHz Ausgang Output Anschluss Connection Frequenzbereich Frequency range Betriebsmodus Operation mode Audiomodus Audio mode TV Standard B G B B D K L Ausgangspegel Output level Video S N ratio R ckflussd mfung Return loss ee D mfung Attenuator Betriebstemperatur Operation temperature Lagertemperatur Storage temperature Luftfeuchtigkeit Humidity Ma e L x B x H Dimensions L x W x H Gewicht Weight 28 POLYTR IN Typ Type DPM AV Master DPM AV Slave Video Eingangspegel Video Input Level 1 Vpp 75 Ohm 1 Vpp 75 Ohm Audio Eingangspegel Audio Input Level 1 Vpp 10k Ohm 1 Vpp 10k Ohm AV Verbindung AV connection RCA RCA Leistungsaufnahme Power consumption Gewicht Weight 85 g 65 g Typ Type DPMFM Eingangsfrequenzbereich Input frequency range 87 5 108 MHz Eingangsimpedanz Input impedance Eingangsr ckflussd mpfung Input return loss Verst rkung Gain Pegelsteller Variable attenuator 75 Q gt 15 dB 34 dB 80 dBuV 0 20 dB 10 dB 10 dB 2 dB 29 POLYTR N NOTIZEN NOTES 7 PolyFlex Belegungsplan Assignment scheme Modulsteckplatz Nr mo
23. een type attitude OFF Einstellung OFF zu w hlen Screen Type Taname Settings Transmitted value How it looks on TV Set in menu 4 3 TV 16 9 TV d pan and scan same but dilated top bottom ignore dilate top bottom pan E 3 scan cut E 3 View 2 3 2 3 4 3 normal mm mm dilate mm mm black bars T ignore dilate left right View2l 2 1 Viewl4 1 4 pan an d scan same but dilated left r ight View 2 3 as View 1 4 pan an d scan cut top bottom View 1 3as View2 4 Viewl3 16 9 normal View 2 4 View 1 1 ignore dilate left right View 2 1 View 1 4 16 9 normal 2 4 Viewll letter box nn bars left right 16 9 16 9 Stream on a 16 9 TV 4 3 Stream on a 4 3 TV whatever the mode je hj i whatever the mode 4 3 Stream on a 16 9 TV 16 9 Stream on a 4 3 TV lerfter hiax pan and scan combined Lenore vals BIEIDAE Displaved black bars Not displaved areas of the stream 24 lerter hax pan and scan combined ignore J 5 Software Update Uber die RS232 Schnittstelle kann bei den Digital modulen der PolyFlex ein Software Update durchge f hrt werden Hierzu werden folgende Hilfsmittel ben tigt PC mit Betriebssystem XP oder Vista und serieller Schnittstelle Polytron Update Software z B DVB Update V201 zip g ngiges RS232 Kabel 5 1 Vorgehensweise Software U
24. eglicher Haftung ausgeschlossen 1 1 Hinweise zu Sicherheitsanforderungen an Antennenanlagen Ihre Antennenanlage muss den Sicherheitsanforde rungen nach EN 50 083 VD 0855 Teil 10 11 12 entsprechen Denken Sie daran Wegen Brandgefahr durch Blitzeinschlag ist es emp fehlenswert alle metallischen Teile auf einer nicht brennbaren Unterlage zu montieren Brennbar sind Holzbalken Holzbretter Kunststoffe etc ATTENTION This unit is equipped with ESD components ESD Electrostatic Sensitive Device An electrostatic discharge is an electrical current pulse which can flow triggered by large tension difference also over a normally electrically isolating material In order to be able to ensure the reliability of ESD as semblies it is necessary to adhere the most im portant handling rules gt Electrostatically sensitive assemblies may be processed only on electrostatically protected work place EPA gt Pay attention to permanent potential compensa tion gt Guarantee person grounding by wrist and shoe grounding gt Avoid electrostatically rechargeable materials like normal PE PVC polystyrene etc gt Avoid electrostatic fields gt 100 V cm gt Use only labeled and defined packing and trans portation materials Damages by faulty connection and or inexpert handling are excluded from any liability 1 1 References to safety requirements at antenna systems Your antenna system must comply w
25. eight Weitere Merkmale Further Features 140 x 120 x 25 mm 0 15 kg Teletext Videotext Untertitel Europ ischer Standard Subtitle European Standard VPS wenn vom Provider unterst tzt if supported by provider WSS Wide Screen Signalling dynamische Umschaltung auf Regionalprogramme dynamical PMT Watchdog Fernbedienung OSD Servicekanal C69 Remote controlled OSD Service Channel C69 Letter Box 27 POLYTR N Eingang Input Transportstrom Steckerleiste Stecker Edge card connector male Transport Stream gem DVB in accordance with DVB AV Ausgang AV Output Anschluss Connection Steckerleiste Stecker Edge card connector male Videopegel Video level 1 Vop 75 O Vi Bandbreite a Een Video S N gt 60 dB Audiopegel Audio level 1 Vpp 10 KQ 3 dB Schritte steps 6 dB 6 dB Audio Bandbreite Audio bandwidth Due Audio S N gt 50 dB Schnittstelle Interface Transportstrom Ausgang Steckerleiste Stecker Edge card connector male Transport Stream output gem B DVB in accordance with DVB Umweltbedingungen Environment conditions Betriebstemperatur Operation temperature Lagertemperatur ER Luftfeuchtigkeit Humidity 20 80 Sonstiges Others Ma e LxBxH on L a x H aU ee SAL Gewicht Weight 0 09 kg 10 50 Typ Type DPM MS DPM MST DPM MM DPM MMT Killer dl Eingang Input Anschluss Conn
26. emperatur Operation temperature Lagertemperatur Storage temperature Luftfeuchtigkeit Humidity Sonstiges Others Ma e L x B x H Dimensions L x W x H 140 x 120 x 25 mm Gewicht Weight 0 15 kg 10 50 20 70 20 80 26 POLYT HO N Dorme me omes ormene Sm mare Eingang Input F Buchse female 75 Q F Stecker male 75 12 VDC max 250 mA _ schaltbar switchable 950 2150 MHz 45 75 dBuV QPSK 36 MHz gem DVB in accordance with DVB Code Rate auto Code rate auto 1 2 2 3 3 4 5 6 7 8 2 35 MBit s gem in accordance with ISO IEC 13818 2 gem in accordance with ISO IEC 13818 3 32 44 1 48 kHz AV Ausgang AV Output Steckerleiste Buchse Edge card connector male 1 Vpp 750 20 Hz 5 MHz gt 60 dB 1 Vap 10 KQ 3 dB Schritte steps 6 dB 6 dB 40 Hz 15 kHz gt 50 dB Schnittstelle Interface Steckerleiste Buchse Edge card connector male Transport Stream output DVB in accordance with DVB Entschlusselung Common CryptoWorks CONAX Common Descrambling Interface embedded embedded Interface Umweltbedingungen Environment conditions Betriebstemperatur Operation temperature 10 50 20 70 20 80 Lagertemperatur Storage temperature Luftfeuchtigkeit Humidity Sonstiges Others Ma e LxBxH Dimensions L x W x H Gewicht W
27. he grey wire of the FM amplifier power supply at the 12 V connection 12V Ausgangsverst rker Output Amplifier FM Verst rker FM Amplifier FM Eingang dient nur zur Befesti FM Input gung NC only for mounting 10 2 6 Modulatoren Die Modulatoren der DPM Serie erm glichen die Modulation von AV Signalen der Master oder Slave Module in frei programmierbare TV Kan le Bei der Monovariante k nnen die TV Standards B G B B D K I und L bei der Stereovariante die TV Standards B G und B B eingestellt werden Die Module werden durch HF Verbindungskabel mit dem Ausgangssammelfeld verbunden Die Stereomodulatoren werden durch Stereocoder erg nzt Bild 5 Bei den Monomodulatoren werden Audio Br cken anstelle eingesetzt Bei Twinmodulatoren m ssen beide Stereocoder bzw Audio Br cken eingesetzt werden Die Einstellung der Modulatoren erfolgt ber die Pro grammierung der dazugeh rigen Digitalmodule Bei Twinmodulatoren erfolgt die Einstellung ber das ers te Digitalmodul da die Ausgangskan le zwangsbe nachbart sind Ausgang zum Ausgangssammelfeld Output to the output combiner Bild 6 Anschluss am Modulator der DPM Serie Bild 7 Stereocoder POLYTRIN 2 6 Modulators The DPM series modules are for modulation of AV signals from the Master or Slave Modules into free programmable TV channels The mono version enables the setting of TV stand ards B G B B D K I and L the stereo version t
28. he TV standards B G B B The modules will be connected with the output com biner by the enclosed RF cables The stereo modulators are completed by stereoco ders Figure 5 The mono modulators go with audio bridges instead Using twin modulators it is necessary to insert the two stereo coders or audio bridges Modulators are set by the programming of the corre sponding digital modules Twin modulators are set by the first digital module because the output channels are adjacent channel operating Figure 6 Connection of the modulator of the DPM series Figure 7 Stereo coder 11 POLYTR N 3 Preparations 3 Vorbereitungen 3 1 Headend Grounding Ground the Headend by connecting the earth Kopfstation uber die Erdungsklemme oss sp terminals to the equipotential bonding rail mit der Potenzialausgleichschiene Ser verbinden 3 2 Grounding Coaxial Cables Remove the insulation of the coaxial cable near the terminal Clamp the stripped cable in the earth strip 3 2 Koaxialkabel erden Den weiBen PVC AuBenmantel des Koaxialkabels im Bereich der Klemme entfernen Abisoliertes Kabel in den Erdungsstreifen einklemmen BE S Te Cel PolyFlex 259 CA N Bild 8 Verdrahtung der Antennen Figure 8 Wiring of the antenna system anlage 3 3 F Stecker aufschrauben F Typ Stecker auf das abisolierte Koaxialkabel z B IK 16 aufschrau ben Achten Sie darauf dass die Abschirmung mit
29. ice channel C69 855 25 MHz Twin Stereo B G Channel A BPRS RCT Tae Input Settings Frequency 11954 MHz LNB LO freq 10600 MHz Symbol Rate 27500 KSis Search Auto OK Channel ZDF Language German Subtitle OFF lt gt Move Programmierfenster Master Modul TV oder Messger t am Ausgang anschlie en einschalten und Kanal 69 einstellen Basisger t einschalten Den SETUP Schalter des zu programmierenden Moduls nach oben auf SETUP schalten LED rot Am Monitor erscheint das oben angezeigte Pro grammierfenster mit Angabe von Modultyp Software Version und Servicekanal Hinweis Das jeweils einzustellende Feld ist far big markiert Die Taste OK der Fernbedienung dr cken das Feld Input Settings ist markiert Hier k nnen alle Eingangsparameter eingestellt werden Dr cken der Taste OK das Feld Frequency ist markiert Jetzt die Frequenz des gew nschten Transpon ders eingeben Mit der Taste CHY auf LNB LO Freq und da nach auf Symbol Rate springen und die jeweili gen Werte einstellen Danach auf Search springen und die Taste OK dr cken Es startet der automatische Suchlauf und listet alle gefundenen TV und Radio Programme in einem neuen Fenster Bild 14 auf DPM PS und DPM PT Output Settings TV Standard Channel Frequency Audio Mode Audio Level Screen Type P S Ratio OK Select Menu B G iC 21 471 25 Stere
30. ith EN 50 083 VD 0855 part 10 11 12 Remember Due to the risk of fires caused by lightning strikes all metal parts must be mounted on a non combustible base Combustible materials include wooden beams and boards plastic boards etc 2 Beschreibung 2 1 PolyFlex DPM Die PolyFlex DPM ist eine kompakte zukunftsorien tierte Kopfstelle f r die modulare Kanalaufbereitung von DVB T und DVB S Signalen Sie wird in kleinen und mittleren Gemeinschaftsanlagen eingesetzt und wartet mit einer Vielzahl von Vorz gen auf wie z B Kompakte Bauweise innovative Master Slave Technologie nachbarkanaltaugliche Modulatoren zukunftsweisende OSD Technik LNB Spannungs Schalter auf jedem Mastermodul hoher Ausgangspegel 100 dBuV durchg ngiger Ausgangsfrequenzbereich 47 862 MHz gt Ausgangssammelfeld Verst rker und Netzteil in tegriert gt Testausgang 20 dB VV VV VV WV Abh ngig vom eingebauten Modul k nnen die TV Standards B G B B D K I WN L eingestellt wer den Das Basisger t verf gt ber acht Modulsteckpl tze und unterst tzt die Umsetzung von bis zu acht Pro grammen Wie in den anderen Polytron Kopfstellen sind in der DPM das Ausgangssammelfeld ein Ver st rker und das Netzteil integriert Alle Eing nge ver f gen ber einen Schalter zur Fernspeisung der LNB s Bei 8 Kan len betr gt der Ausgangspegel der Kopfstelle 100 dBuV Ein Testausgang mit 20 dB re duziertem Pegel steht f r Messungen u
31. llen uber die Fernbedienung Connection and adjusting over the remote control geschehen sinngemaB in gleicher Weise wie in Ab happens in the same way as described in section schnitt 4 2 2 Master Module DPM beschrieben 4 2 2 Master Module DPM Hinweis Das jeweils einzustellende Feld ist farbig Note The field to be programmed is highlighted markiert Bei Twinmodulatoren sind die The channels of the twin modulators are Kan le zwangsweise nachbarkanalbelegt compulsory adjacent channel operating Only es l sst sich f r Kanal B nur der Audi the audio mode can be adjusted for channel omodus einstellen Bei Singlemodulato B With single modulators all values can be ren k nnen alle Werte im Feld Output set in the field Output Settings Further in Settings eingestellt werden Weitere In formation in addition see section 4 2 2 formation dazu siehe Abschnitt 4 2 2 23 POLYTR N Beschreibung Funktion Screen Type Description Screen Type Operation In Gemeinschaftsanlagen in denen nur 4 3 bzw In communal facilities in which only 4 3 and or 16 9 16 9 Fernsehger te verwendet werden empfiehlt es television sets are used it is advisable to select the sich die Screentype Einstellung 4 3 bzw 16 9 zu screen type attitude 4 3 and or 16 9 w hlen In Gemeinschaftsanlagen mit unterschiedlichen In communal facilities with different television types it Fernsehertypen empfiehlt es sich die Screentype recommends to select the scr
32. n und die jeweili gen Werte einstellen Danach auf Search springen und die Taste OK dr cken Es startet der automatische Suchlauf und listet alle gefundenen TV und Radio Programme in einem neuen Fenster auf pears indicating Module Type Software Ver sion and Service Channel at the monitor Note The field to be programmed is highlighted The field Input settings is highlighted Press the button OK of the remote control the field Frequency is highlighted Now enter the frequency of the desired tran sponder Jump with the key CHY on LNB LO Freq and af terwards on Symbol Rate and set the respective values Jump on Search and press the button OK The automatic scanning starts and lists all found TV and radio programs in a new window POLYTR N CHANNEL SETUP ini 1 14 RARE 002 a 003 ORF2 W 004 ORF2 N 005 ORF2 B 006 ORF2 O 007 ORF2S 008 ORF2T 009 ORF2 V 010 ORF2 St Ty Move MENU Swi i Bild 16 CHANNEL Setup Fenster 9 Mit den Tasten A V einen Sender aus der ange zeigten Liste markieren Mit der Taste MENU in das Feld Transponder springen und falls vorhanden die gewunschte Sprache in den Feldern Language und Subtitle einstellen Mit der Taste OK die Einstellungen speichern 10 Jetzt zum Men punkt Output Settings navigie ren 11 Jetzt werden die gew nschten Daten f r die Ein stellung des Modulators in gleicher Weise wie im Fenster Input Settings eingestellt und durch D
33. nd Service zur Verf gung Die Master Module sind mit einem Tuner zum Emp fang des gew nschten Transponders best ckt Sol len mehrere Programme aus diesem einen Trans ponder umgesetzt werden kommen Slave Module zum Einsatz Der vom Master Modul aufbereitete MPEG Datenstrom wird an die Slave Module weiter gegeben Es ist somit m glich mit nur einem Master Modul und sieben Slave Modulen acht Programme aus einem Transponder aufzubereiten Die aufbereiteten A V Signale werden dann an eben falls steckbare Modulatoren weitergeben Das Polyt ron Programm bietet sowohl Single als auch Twin modulatoren Bei den Twinmodulatoren sind die Ka n le zwangsweise nachbarkanalbelegt z B Kanal 21 und 22 Bei der Best ckung der Grundeinheit ist auf die Steckplatzbeschriftung auf der Grundplatte zu achten Bei der Verwendung von Twinmodulatoren werden diese in die ungeraden Modul Steckplatze 1 3 5 7 gesteckt die benachbarten Steckpl tze blei ben leer Beim Einsetzen von Stereo codern werden allerdings die beiden benachbarten Stereocoder Steckpl tze best ckt POLYTRN 2 Description 2 1 PolyFlex DPM The PolyFlex DPM is a compact future oriented headend for modular channel processing of DVB T and DVB S signals It is deployed in small and middle sized communal facilities and has a vast number of advantages for example Compact Design innovative Master Slave technology adjacent channel operating modulators advanced OS
34. o 0 db OFF 116 dB Ns lt gt MHZ lt gt le gt lt gt a Beschreibung Screen Type Seite 24 Description Screen Type Page 24 Figure 13 Programming window Master Module Connect the TV or measuring instrument at the output turn it on and adjust channel 69 Turn on base unit Turn the switch of the module to be programmed up to position SETUP LED lights red The above indicated programming window ap pears indicating Module Type Software Ver sion and Service Channel at the monitor Note The field to be programmed is highlighted Press the button OK of the remote control the field Input Settings is highlighted In this menu all inout parameters can be modified Press the button OK the field Frequency is high lighted Now enter the frequency of the desired tran sponder Jump with the key CHY on LNB LO Freq and af terwards on Symbol Rate and set the respective values Jump on Search and press the button OK The automatic scanning starts and lists all found TV and radio programs in a new window Figure 14 CHANNEL SETUP Channels 1 7 N 001Das Erste L 1002 Bayerisches FSS 003 hr fernsehen 004 Bay flsches FS N 005 WOR K ln 006 BR alpha 007 SWR Fernsehen BW Signal level POLYTRIN Transponder TV free Frequency 11836 MHz Video PID 101 Audio PID 102 Language German lt gt Subtitle NONE 71 3 Signal q
35. of persons At references to a component provided by a place number e g fig ure 1 3 the reference corresponds to picture 1 place number 3 1 Sicherheitsvorkehrungen Vor dem Arbeiten am Grundger t DPM bitte un bedingt folgende Sicherheitsbestimmungen sorg f ltig lesen ACHTUNG Das Offnen des Ger tes sollte nur von autorisiertem Fachpersonal durchgef hrt werden Zum Aus und oder Einbau eines Moduls muss das Grundger t immer stromlos sein Netzanschluss und Netzkabel Das Ger t darf nur an einem Stromnetz mit einer Wechselspannung von 190 250 VAC 50 60 Hz betrieben werden Anschlusskabel Anschlusskabel immer stolperfrei verlegen Erdung der Anlage Nach den EN 50 083 VDE 0855 Bestimmungen muss die Satellitenanlage den Sicherheitsbestim mungen wie z B Erdung Potenzialausgleich etc entsprechen Feuchtigkeit und Aufstellungsort Das Ger t darf nicht Tropf oder Spritzwasser ausge setzt werden Bei Kondenswasserbildung unbedingt warten bis das Ger t wieder trocken ist Umgebungstemperatur und Hitzeeinwirkung Die Umgebungstemperatur darf 50 nicht ber schreiten Die L ftungsschlitze des Ger tes d rfen auf keinen Fall abgedeckt werden Zu starke Hitze einwirkung oder W rmestau beeintr chtigen die Le bensdauer des Ger tes und k nnen eine Gefahren quelle sein Das Ger t darf nicht direkt ber oder in der N he von W rmequellen z B Heizk rpern Heizungsanlagen o montiert werden
36. ownward on OFF again the LED stellen die LED leuchtet wieder gr n Nun kann lights green again The next module can be pro das n chste Modul in sinngem gleicher Weise grammedin the analogously way programmiert werden 20 4 2 4 Slave Modul DPM SL Module Type Slave POLYTRIN 4 2 4 Slave Module DPM SL SSB Stereo BIG Modulator Software Version 0 34 C 69 966 26 MHz TV Standard BG ae Channel C24 gt Frequency 496 26 MHz Audio Mode Stereo a gt Channel ZDFdokukana Audio Level FEE ae Language German Video Level 0 ar Subtitle Screen Type Auto a PIS Ratio Bild 18 Programmierfenster DPM SL Slave Die Einstellungen des Slave Moduls entsprechen den Einstellungen des dazugeh rigen Master Moduls Mit dem Slave Modul kann man nur die Programme des Transponders empfangen der f r das Master Modul ausgew hlt wurde Deswe gen sind die Einstellm glichkeiten des Slave Moduls begrenzt Schritte 1 bis 4 der Programmierung des Master Moduls durchf hren Die Taste CHW der Fernbedienung dr cken jetzt ist das Feld OK von Channel Search markiert Taste OK dr cken Das Slave Modul scannt die eingehenden Signale und erstellt eine Programm liste 1248 ae Beschreibung Screen Type Seite 24 Description Screen Type Page 24 Figure 18 Programming window DPM SL Slave The adjustments of the Slave module correspond to them of the
37. pdate 1 Entzippen Sie das Software Paket und installie ren die Update Software durch Starten des Setup exe Programms 2 Starten Sie die Flex Update Utility V201 exe Software 3 Wahlen Sie den gew nschten COM Port aus der Kontrollleiste aus einmalig 4 Grundgerates PolyFlex ausschalten 5 COM Anschlu durch RS232 Kabel mit RS232 Schnittstelle auf der Grundplatte verbinden 6 Grundgerates wieder einschalten 7 Setup Schalter des gew nschten Moduls in den Servicemodus SET stellen LED leuchtet rot Hinweis Es darf sich immer nur ein Modul im Servicemodus befinden 8 Update durch Best tigung des Update Buttons starten Der Modultyp wird automatisch ermittelt und up gedatet Ein blauer Balken zeigt den Fortschritt des Update Vorgangs an Bitte vermeiden Sie w hrend des Update Vorgangs andere Computerprogramme zu ffnen die Kopfstation auszuschalten den Computer auszuschalten den Update Vorgang abzubrechen das Update Fenster zu verschieben 9 Nach erfolgreichem Update Vorgang erscheint die Nachricht Update successful 10 Nach Beendigung des Updates Setup Schalter zur ck auf OFF stellen LED leuchtet gr n 11 F r weitere Modul Updates wiederholen Sie das Vorgehen ab Punkt 7 oder beenden Sie das Up date Programm durch bet tigen des Exit Buttons Bemerkung Erfahrene Benutzer k nnen den Experten Modus w hlen Dieser Modus erm glicht die manuelle Aus
38. r cken der Taste OK gespeichert 12 Falls mehrere Programme von dem DPM PS ME Mastermodule entschl sselt werden sollen den Button Select Slave anw hlen Hier wird festge legt welche weiteren Programme entschl sselt werden und den folgenden Slave Modulen ber den Datenstrom zur Verf gung gestellt werden sollen Die Einstellung dieser Programme erfolgt dann ber das entsprechende Slave Modul Falls nicht zu Punkt 16 springen Transponder TV scrambled Frequency 12692 lMHz II Video PID 160 Audio PID 161 Language German lt gt Subtitle NONE Signal level 65 8 Signal AAN II 99 9 ich OK Store EXIT Caneel Figure 14 CHANNEL Setup Window 9 Mark a program from the indicated list by keys AY Jump into the field Transponder with the button MENU set the desired language to the fields Language and Subtitle if available Save the adjustment with the button OK 10 Now navigate to the menu point output settings 11 Now the desired data for the adjustment of the modulator are set similarly to Input Settings and have to be saved by pressing the button OK 12 If more channels should be decrypted by the DPM PS ME Master Module choose the Select Slave button In this area you choose further channels to be decrypted The encrypted channels will be send via data stream to the following slave moduls The settings of these channels will be done by the corresponding sl
39. schlie en Jetzt die Modulatoren Bild 11 13 einbauen Bei den Stereomodulatoren werden die dazugeh ri gen Stereocoder beliebig herum in die entspre chenden Steckpl tze eingesetzt Bei den Mo nomodulatoren m ssen die Audio Br cken ein gesetzt werden Bild 11 11 Bei Twinmodulato ren m ssen beide Stereocoder bzw Audio Br cken eingesetzt werden Die Modulatoren Bild 11 13 ber die dazugeh rigen HF Kabel Bild 11 12 mit dem Ausgangs sammelfeld Bild 11 10 verbinden Masseschiene Bild 11 7 aufsetzen und mit ihren an beiden Enden befindlichen Schlitzen unter die beiden Schrauben Bild 11 8 schieben und diese festschrauben Dabei die Module so ausrichten dass sie in den Schlitzen der Masseschiene geh altert werden Ger t in die vorbereiteten Schrauben einh ngen und die unteren Schrauben eindrehen Erdungskabel am Erdungsanschluss Bild 11 9 des Geh uses festschrauben 4 4 1 gt POLYTRN Commissioning Installing the modules Prepare assembly ground according to the de scription on the enclosed drilling jig Unscrew the two cross head screws Figure10 8 of the mass rail Figure 11 7 and pull it down wards Insert CAM modules and Smart Cards into the corresponding Master Modules if applicable Plug the first Master Module Figure 11 3 into the first slot and screw it down with its mounting bracket Figure 11 2 onto the strip Connect the accompanying HF cable Figure 11 1 at th
40. t ausschlie t Bei Hinweisen auf ein durch eine Ortszahl versehenes Bauteil z B Bild 1 3 bezieht sich in diesem Beispiel der Hinweis auf Bild 1 Ortszahl 3 Sicherheitsvorkehrungen Safety precautions Beschreibung Description Vorbereitungen Preparations Inbetriebnahme Commissioning Software Update Software Update Technische Daten Technical Data Belegungsplan Assignment scheme NOTE The contents of this company manual are copyrighted and must not be duplicated or copied in any form either partially or in full without the prior consent of the editor Changes in this company manual which are carried out without consent of the creator can lead to the loss of the guarantee or to the rejection of the product liability on the part ofthe manufacturer The editor is grateful for suggestions Editor Polytron Vertrieb GmbH Postfach 10 02 33 75313 Bad Wildbad Germany The following emphases are used in this manual with the following meanings NOTE applies to technical requirements which must be taken into account to ensure a faultless function of the device plant ATTENTION refers to instructions which have to be adhered exactly to avoid damage or destruction of the de vice CAUTION applies to instructions whose nonobservance doesn t exclude the endangering
41. uality 91 3 II ly if j H love ME Bild 14 CHANNEL Setup Fenster 9 Mit den Tasten A V einen Sender aus der ange zeigten Liste markieren Mit der Taste MENU in das Feld Transponder springen und die gew nschten Felder Langu age Subtitle und Teletext einstellen Mit der Taste OK die Einstellungen speichern 10 Der Cursor springt auf das Feld Channel A des ersten Fensters zur ck 11 Mit OK gt Output Settings gt OK die gew nsch ten Einstellungen des Modulators in gleicher Weise wie im Fenster Input Settings einstellen und durch Dr cken der Taste OK speichern 12 Bei der Verwendung von Twinmodulatoren sie he Punkt 14 13 Die Programmierung ist abgeschlossen Jetzt den Schalter SETUP wieder auf OFF nach unten stellen die LED leuchtet gr n Nun kann das n chste Modul in sinngem gleicher Weise pro grammiert werden 14 Bei Twinmodulatoren im obersten Men punkt Channel B ausw hlen Wie auf dem Bildschirm angezeigt OK dr cken und den Schalter des zweiten Empfangsmodules auf SETUP stellen Beide LNBs leuchten nun rot 15 Die Eingangsparameter wie ab Punkt 6 beschrie ben einstellen Hier entf llt die Einstellung des Ausgangskanals es wird automatisch der obere Nachbarkanal von Kanal A ausgew hlt Zum Beispiel Kanal A K21 nun wird Kanal B automatisch auf K22 eingestellt 16 Nach der Programmierung beide Schalter auf OFF stellen die LED leuchtet gr n NU Switch OF 9 EXIT I C
42. ulen DPM PT handelt es sich um Emp fangsmodule zur Umsetzung von terrestrischen COFDM modulierten Programmen in AV Signale Die Module DPM PT ME und DPM PTI bieten zu s tzlich die M glichkeit verschl sselte Programme aufzubereiten Das Modul DPM PT ME entschl sselt mehrere verschl sselte Programme gleichzeitig und stellt diese den folgenden Slave Modulen ber den Datenstrom zur Verf gung Das empfangene Signal wird dem Mastermodul ber die Eingangsbuchse zugef hrt und kann ber den Durchschleifausgang zum n chsten Mastermodul einmal durchgeschleift werden Das AV Signal wird anschlie end von einem Modula tor aus der DPM Serie der ber das Motherboard mit dem eingesetzten Digitalmodul verbunden ist in ei nen TV Kanal gewandelt Der LNB Schalter dient zum Einschalten der LNB Versorgungsspannung und der SETUP Schalter zum Aktivieren des Programmiermodus Bild 2 Bedienelemente und Anschl sse am Master Modul POLYTRIN 2 2 Master modules DPM PS PSI PS Conax CryptoWorks DPM PS ME DPM PT PTI PT ME The modules DPM PS Master are DVB S reception modules for conversion of QPSK modulated pro grams into AV signals The modules DPM PS ME PSI PS CryptoWorks and PS Conax furthermore admit the processing of encoded programmes The PSI modules need a CAM module The PS Cryp toWorks and PS conax modules have the corre sponding descrambler embedded The module DPM PS ME decode several channels simultaneousl
43. update procedure 10 After update procedure is finished set the Set upswitch back to OFF LED colour changes to green 11 Repeat procedure for further updates starting with step 7 or finish by pressing Exit icon Remarks Advanced users could choose the EXPERT update mode This mode allows to select the update files by manual operation The expert mode is protected by a password Details regarding expert mode will be available on request from our service department 25 POLYTR N 6 Technische Daten 6 Technical Data Typ Type Eingang Input Steckpl tze Slots LNB Spannungsversorgung LNB DC Supply Versorgungsspannung Power Supply Leistungsaufnahme Power consumption Ausgang Output Frequenzbereich Frequency range 47 862 MHz Ausgangspegel 8 Kan le Output level 8 channels 100 dBuV D mpfung Attenuation 10 dB einstellbar adjustable Ausgangsverstarkung Output amplifier gain 10 dB R ckflussd mpfung Return loss gt 10 dB Testausgang Test output 20 dB Schnittstellen Interfaces Fernbedienung Remote Control Update Umweltbedingungen Environment conditions Umgebungstemperatur Ambient temperature Lagertemperatur Storage temperature Sonstiges Others Ma e B x H x T Dimensions W x H x D 440 x 365 x 170 mm Gewicht Weight 6 2 kg 12 VDC max 500 mA 180 265 VAC 50 60 Hz max 100 W RS232 10 50 20 70 Typ Type Eingang Input
44. wo das Ger t Hitzestrahlung oder Old mpfen ausgesetzt ist _ Wegen der Brandgefahr durch berhitzung oder Blitzeinschlag ist es empfehlenswert das Ger t auf einer feuerfesten Unterlage zu montieren Sicherungen Sicherungen sollten nur von autorisiertem Fachper sonal gewechselt werden Es d rfen nur Sicherungen des gleichen Typs eingesetzt werden POLYTRIN 1 Safety precautions Before working on the base unit DPM please read the following safety precautions carefully ATTENTION The unit should only be opened by qualified persons For removement and or installation of a module the base unit must always be currentless Mains connection and mains cable Only operate the device at a specified voltage of 190 250 VAC 50 60 Hz Connection cable Lay cables that they cannot be tripped over Grounding of the system According to the regulations EN 50 083 VDE 0855 the satellite plant must correspond to the safety regu lations e g grounding potential equalization etc Humidity and place of assembly The equipment may not be exposed dripping or splash water In case of condensed water formation wait until the device is dry again Ambient temperature and influence of heat The ambient temperature must not exceed 50 Don t cover the louvers of the device To strong heat effect or accumulation of heat impairs the life span of the equipment and can be a source of danger The unit must not be installed directly a
45. y and provide them to the following slave modules via data stream The modules DPM PT are reception modules for conversion of terrestrial COFDM modulated pro grams into AV signals The modules DPM PT ME and DPM PTI furthermore admit the processing of encoded programmes The module DPM PT ME de code several channels simultaneously and provide them to the following slave modules via data stream The received signal is supplied to the master module via the input socket and can be looped through over the loop through output to the next master module once Afterwards the AV signal is converted into a TV channel by a modulator from the DPM series Via the motherboard the modulator is connected with the in serted digital module The LNB switch serves for turning on the LNB re mote feeding voltage and the SETUP switch for acti vating the programming mode Eingang Input Durchschleifausgang Loop through LNB Schalter LNB switch Setup Schalter Setup switch Figure 2 Switches and connections of the master module POLYTR N 2 3 Slavemodul DPM SL Die Slave Module DPM SL empfangen den Daten strom vom Master Modul und ben tigen daher keinen eigenen Tuner Aus diesem Datenstrom wird ein Ka nal selektiert und in ein analoges AV Signal umge setzt Deswegen kann man mit einem Slave Modul auch nur einen Kanal des Transponders selektieren auf den das Master Modul programmiert ist Das AV Signal wird anschlie end von einem
Download Pdf Manuals
Related Search
Related Contents
Betriebsanleitung - Brandt, Alexander 資料№5-26 別表第十二に提案する規格の概要 Appel d`urgence pour Gaza - Centre de crise MatrikonOPC Modbus Driver MANUEL D`EMPLOI Manual da Comunicação CANopen Epson EB-S11 Copyright © All rights reserved.
Failed to retrieve file