Samsung AW0560A User Manual
Contents
1. Installation Cont 4 Attach the seal strip to the window 4 1 Cut the adhesive backed foam seal strip gasket to the window width 4 2 Remove the backing from the seal strip and attach the strip to the underside of the bottom window 5 Install the unit in the window 5 1 Place the air conditioner cabinet into the window with the top support channel positioned just in front of the bottom sash 5 2 Center the cabinet side to side in the window then pull the window down until it rests on the air conditioner just behind the mounting channel front flange on top of the cabinet 5 3 Make sure the cabinet maintains a slightly downward slant to the outside A 1 4 slant cabinet front to rear is desirable to help prevent water from entering the room 1 4 6 Extend the window filler panels 6 1 Secure the window brackets to the stool using the Type A screw at each side 6 2 Secure the top mounting channel to the bottom sash with the Type A screw in the center 6 3 Extend the window filler panels into the window sash tracks It on both sides When the window is pulled down the window should a rest on the unit just behind the window filler panel frames fl 6 4 Slide the window filler panels outward until they touch the sides re of the window Secure the panels by putting four Type A screws Me A STW through the mounting holes2. OWNER S INSTRUCTIONS AW0560A AW0660A WINDOW TYPE ROOM AIR CONDITIONER Cool Safety Precautions The following safety precautions must be taken when using your air conditioner 1 The unit must be plugged into an independent circuit The air conditioner must be installed in accordance with national wiring regulations and safety regulations wherever applicable 2 Some installation locations may require installation of a short circuit breaker or grounding 3 Ifthe supply cord is damaged it must be replaced by a special cord or assembly available from the manufacturer or its service agent 4 MAKE sure that the unit is correctly ventilated at all times do NOT place clothing or other materials over it 5 NEVER spill any kind of liquid into the unit Should this happen unplug the unit and contact an authorized service center 6 Do NOT insert anything between the air outlet blades because the inner fan may be damaged and could cause injury Keep children away from the unit 7 Do NOT place any obstacles in front of the unit 8 Users of this product are cautioned not to attempt repairs Instead they are requested to directly contact a designated service center or the outlet at which the product was purchased 9 Do not use an extension cord with this product 10 The appliance is not intended for use by young children without supervision young children should be supervised to ensure that they do not play with the appli
3. book customer adjustments routine maintenance and cleaning consumable items such as filters use of non SAMSUNG or unauthorized parts supplies accessories or equipment which damage this product or result in service problems THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE AND NO WAR RANTIES WHETHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL APPLY AFTER THE EXPRESS WARRAN TY PERIODS STATED ABOVE AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON FIRM OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS FAILURE TO REALIZE SAVINGS OR OTHER BENE FITS OR ANY OTHER SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE MISUSE OR INABILITY TO USE THIS PRODUCT REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE WITHOUT LIMITING THE FOREGOING PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS DAMAGE OR INJURY TO PURCHASER AND PURCHASERS PROP ERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE MISUSE OR INABILITY TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUN
4. fan and compressor cycle on and off together The fan will continue to run for a short time after the compressor cycles off gt if you would like the air conditioner to run in Fan mode do not press the Energy Saver button You cannot use the Fan mode in the energy saving mode 2 To stop the energy saving mode press the Energy Saver button on the remote control or unit again Result The fan runs at all times while the compressor cycles on and off gt Ifyou select the Sleep Timer in the Energy Saving mode the Energy Saving will be cancelled and the air conditioner will start up in the Sleep Timer mode Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used Mode Indoor Temperature Outdoor Temperature Indoor Humidity Cooling 70 F to 90 F approx 70 F to 110 F approx 80 or less If the air conditioner is used at Then Higher temperature The automatic protection feature may be triggered and the air conditioner stopped Lower temperature A water leakage or some other malfunction may happen if the heat exchanger freezes Higher humidity levels Water may condense on and drip from the surface of the unit if it is used for long periods Cleaning Your Air Conditioner Be sure to clean the air filter periodically to maintain the air conditioner in the best condition for a long period of time When cleaning the air con
5. in the panels and driving them into the window stool and sash Type A screws 7 Install the window gasket Cut the foam window gasket to the window width and stuff it between the window and the glass to prevent air and insects from getting into the room A 8 Check for air leaks and seal 9 Plug in the power switch on the air conditioner turn the air conditioner on and operate it in Cool mode and check for unusual vibrations gt After several minutes the unit will be blowing out cold air lf the unit is not cold please return it to the dealer Installation Cont Removal of the Front Grille If you need to remove the front grille for replacement follow the steps below 1 Remove the screw that holds the grille in place gt Remove the shipping tape before pulling out the air filter if necessary 2 Disassemble the front gril
6. G THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or con sequential damages so the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state To obtain warranty service please contact SAMSUNG at SAMSUNG ELECTRONICS AMERICA INC CONSUMER ELECTRONICS CUSTOMER SERVICE 400 Valley Road Suite 201 Mount Arlington NJ 07856 Tel 973 601 6000 Fax 973 601 6001 1 800 SAMSUNG 1 800 726 7864 www sosimple com
7. ance 11 Never store or ship the air conditioner upside down or sideways to avoid damage to the compressor 12 If the remote control will not be used for a long time remove the batteries CAUTION The manufacturer does not assume responsibility for accidents or injury caused by an incorrectly installed air conditioner If you are unsure about installation contact an installation specialist Contents PREPARING YOUR AIR CONDITIONER Safety Precautions sccc2gcc cuca seiadevesaceeincdeadiaadeechanedeedsseccbasseabsnceecnacednediassaedesmode 2 Description Of Each COMPONENT cccccceeeeeeeecceeeeeeeeceeeeseeeeeeeeeeeesesseeaeaees 4 Remote Control BUttOnS srecne e R E E Aia 5 Genn Saed reese i E a R 6 Inserting the Remote Control Batteries ccccccccccssesseeeeeeceeeeesesaeeaeeeeeees 7 OPERATING YOUR AIR CONDITIONER Cooling Your ROOM ites ce cso ae tel ete ethos 8 ARNO XOU ROON siecle Teeni aaa a EE 9 Adjusting the Air Flow Direction Horizontally cccccccccecsssseeeeeeseeeeeeeeeeeaeas 10 PROGRAMMING YOUR AIR CONDITIONER CTO Ae ON TIMET sarin a a a N 11 SeN OM MINMG Is raserna iA a 12 SEWING the Sleen TIMEN srra e r a aT 13 Selecting Energy Saving MOE s isiat a e e eaa e 14 RECOMMENDATIONS FOR USE Temperature and Humidity Ranges cccccssseeecceeeeeeeeseeeeeeeseeseeesseeneeessaaes 15 Cleaning Your Air Conditioner ccccccccccceecceeseeeeeeeeeeeeeeseeesaeese
8. ation of the inner air flow blades on the unit Adjust the air flow blades to the desired position by pushing them side to side Cea Ea S H GG ttl m f tt 01 Mm 1 toto 0 of U1 UM Ul 1 a C1 Tt mA ML WA U7 E L U G7 3 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given time You can select the On timer only when the air conditioner is off You can select the On timer only when the air conditioner operates in the Cool mode Remote Control Control Panel 1 Check that the air conditioner has been switched off if necessary press the l On Off button 2 Set the operating time by pressing the Timer button on the remote control or unit one or more times until the desired time is displayed The operating time can be set between 1 and 12 hours Result Each time you press the Timer button The time is adjusted by 1 hour and displayed on the control panel The unit beeps The operating time is displayed and decreases automatically to indicate the remaining time The air conditioner starts up in the Cool mode automatically when the operating time reaches zero gt You can adjust the temperature and fan speed after setting the On timer To Cancel the On Timer To cancel the timer press Timer on the remote control or unit one or more times until is displayed or on the remote control or unit The air conditioner op
9. ditioner turn it off and pull out the power plug gt If you Will not be using the air conditioner for a long period of time Have not used the air conditioner for a long period of time 1 Grab the tabs on the filter and pull it up and out 2 Remove all dust on the air filter with a vacuum cleaner or brush 3 When you have finished insert the air filter back into its original position 4 Wipe the surface of the unit with a neutral detergent and then wipe it again with dry cloth Be sure not to use benzene solvent or other chemical products Then Set the fan to F1 and let it for a few hours to dry the inside of the air conditioner thoroughly Switch the air conditioner off and unplug it from the wall socket Clean the filter and outer surfaces Set the fan to F1 and let it run for a few hours to dry the inside of the air conditioner thoroughly Solving Common Problems Before contacting an authorized service center perform the following simple checks They may save you the time and expense of an unnecessary call Problem The air conditioner does not operate at all The air conditioner does not operate with the remote control No beep is heard when you press D On Off on the remote control The air conditioner does not cool The timer is not correctly triggered Odors are permeating the room durin
10. eeeeeeeeeeseaeas 16 Solving Common Problems voiis a s tus aeaes 17 TECHNICAl SP SCIICATONS assen E 17 INSTALLATION Description of Each Component The design and shape are subject to change depending on the model Inner air flow blades right left orientation ES eWl ee a tr le ee E T es ee a ae ey LI Air outlet OUGTIELL Outer air flow blades Air filter POU NQQNPNNDVBUY Air inlet Outside Air inlet inside Power plug The type of the power plug may differ depending on the local power supply Energy Saver indicator a s em Energy Saver button nergy Saver a settings Timer setting button j Timer v Temperature adjustment ae buttons Timer indicator TEMP Fan speed adjustment button j7 Fan Speed Sleep q timer setting button F1 Low F2 Med Mode Operating mode selection ON OFF button s Power button COOL FAN Remote control sensor Remote Control Buttons Timer setting button zl 3 D O fals I e Temperature adjustment Sleep timer setting button buttons f El Operating mode selection buttons Fan speed adjustment buttons O Energy Saver button ON OFF button Getting Started You have just purchased a Samsung window type room air c
11. erates in the mode selected when the unit was last used Setting the Off Timer The Off Timer enables you to switch off the air conditioner automatically after a given time You can select the Off timer only when the air conditioner operates in the Cool mode Remote Control Control Panel 1 Check that the air conditioner has been switched on if necessary press the l On Off button 2 Set the operating time by pressing the Timer button on the remote control or unit one or more times until the desired time is displayed The operating time can be set between 1 and 12 hours Result Each time you press the Timer button The time is adjusted by 1 hour and displayed on the control panel The unit beeps The operating time is displayed and decreases automatically to indicate the remaining time The air conditioner switches off automatically when the operating time reaches zero gt You can adjust the temperature and fan speed after setting the Off timer To Cancel the Off Timer To cancel the timer press Timer on the remote control or unit one or more times until is displayed or C on the remote control or unit The air conditioner operates in the mode selected when the unit was last used Setting the Sleep Timer The Sleep Timer can be used when you are cooling your room to switch the air conditioner off automatically after 8 hours gt If you wish to switch the u
12. facturer does not assume responsibility for accident or injury caused by an incorrectly installed air conditioner If you are unsure about installation contact an installation specialist Checkpoints prior to installation 1 Check the cabinet and front grille of the unit for any defects such as scratches 2 Be sure to check the power supply Refer to the specifications on the label attached to the unit Installation instructions 1 Electrical Requirements For personal safety This appliance must be properly grounded Do not under any circumstances cut or remove the third grounding prong from the power cord We recommend that you do not use an extension cord or an adapter plug with this appliance Do not change the plug on the power cord of this appliance Follow national electrical codes or local codes and ordinances 115V 230V 208V 230V 208V 230V 208V 15 AMP circuit 20 AMP circuit 15 AMP circuit 30 AMP circuit parallel type perpendicular type tandem type tandem type OO OS If the electric supply provided does not meet the above specifications call a licensed electrician Aluminum house wiring may pose special problems consult a qualified electrician This unit requires a separate circuit serving only this appliance 2 Window Requirements Standard double hung window with actual opening width of 22 to 36 The installation will need to be modified for windows other than the standa
13. g air conditioning Explanation Solution o gt o Check that the circuit breaker used for the air conditioner has not been triggered Check that the power cable is plugged into a wall socket and the socket is switched on if necessary Check that the temperature indicator on the unit is lit if necessary press On Off on the remote control or unit Check that there are no obstacles between you and the unit Replace the remote control batteries if necessary Check that you are close enough to the unit seven metres yards or less Check that you are pointing the remote control at the remote control sensor on the unit Replace the remote control batteries if necessary Check that the correct operating mode has been selected COOL The room temperature may be too low Dust may be blocking the air filter refer to page 14 for cleaning instructions Check that there is no obstacle blocking the air flow into or out of the unit Check that the timer has been programmed correctly refer to page 11 13 Ventilate the room Technical Specifications Design and specifications are subject to change without notice Model Power Supply AWO0560A AWO660A 115V 60Hz Installation 22 to 36 12 7 8 min Before installation please read the INSTALLATION instructions then follow the procedures in order after considering the installation area and drain hose CAUTION The manu
14. le 2 1 Press both sides of the cabinet in the direction of the arrow as shown in the figure 2 2 Pull the lower part of the front grille slightly forward gt Do not pull bottom edge of grille toward you more than 3 Damage to the grille s two top tabs may occur 2 3 Grasp the grille at both sides near the bottom and carefully lift it straight up to disengage the grille s two top tabs from slots near the top of the cabinet 3 Reinstall the front grille 3 1 Fix the upper front grille 3 2 Slide one side of the lower part of the front grille slightly backward 3 3 Slide the other side backward 3 4 Reinstall the screw and the air filter SAMSUNG ROOM AIR CONDITIONER LIMITED WARRANTY TO ORIGINAL PURCHASER This SAMSUNG brand product as supplied and distributed by SAMSUNG ELECTRONICS AMERICA INC SAM SUNG and delivered new in the original carton to the original consumer purchaser is warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of One 1 Year Parts and Labor Five 5 Years Parts Warranty for Compressor This limited warranty begins on the original date of purchase and is valid only on products purchased and used in the United States Warranty repairs must be performed by SAMSUNG s authorized service center To receive warranty service the orig inal dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNG s autho
15. mer or Press the Fan Speed button on the unit one or more times until the desired Fan speed F1 F2 or F3 is displayed Energy Saver 5 To control the direction of the air flow refer to page 10 Airing Your Room If you want to provide air circulation without cooling you can use the Fan mode 1 If necessary press the On Off button Result The air conditioner starts up in the mode selected when the unit was last used The unit beeps twice 2 If the fan speed F1 F2 or F3 is not displayed on the control panel Press the FAN button on the remote control or Press the Mode button on the unit one or more times until the fan speed F1 F2 or F3 is displayed Result The unit beeps each time you press the Fan Mode button The air conditioner starts up in Fan mode gt You can change modes at any time When the air conditioner is in the Fan mode the temperature cannot be set or displayed 3 To set the fan speed Press the HIGH MED or LOW button on the remote control as desired or Press the Fan Speed button on the unit one or more times until the desired fan speed F1 F2 or F3 is displayed 4 To control the direction of the air flow refer to page 10 Remote Control Control Panel Energy Saver Fan Speed F1 Low F2 Med F3 Hiah Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room you can adjust the orient
16. nit off at a specific time refer to page 12 Remote Control Control Panel 1 Make sure that you have selected COOL mode 2 Press the Sleep button on the remote control or Press the Sleep button on the unit Result Each time you press a button the unit beeps The SLEEP passes through the control panel for about 15 seconds and the H will be displayed The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time The air conditioner will be controlled as illustration below Cooling When the temperature has been increased by 2 F after 1 hour it is maintained for 7 hours To Cancel the Sleep Timer To cancel the timer press Sleep on the remote control or Sleep on the unit Result The unit beeps The SLEEP indicator is no longer displayed The air conditioner operates in the mode selected last gt If you select the Energy Saving mode in the Sleep Timer mode the Sleep Timer will be cancelled and the air conditioner will start up in the Energy Saving mode Selecting Energy Saving Mode R c i If you wish to save energy when using your air conditioner emote Gontro Control Panel select the energy saving mode with the Energy Saver button 1 To select the energy saving mode press the Energy Saver button on the remote control or unit one or more times until the Energy Saver indicator lights up Energy Saver Result The
17. onditioner which should be installed following your installation manual Your Owner s Instructions contain much valuable information on using your air conditioner Please take the time to read them as they will help you take full advantage of the unit s features The booklet is organized as follows The following figures are shown on pages 4 and 5 Description of Each Component Remote control buttons They will help you find the buttons and understand the symbols displayed Inthe main part of the document you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use four different symbols C om gt IMPORTANT NOTE Inserting the Remote Control Batteries You must insert or replace the remote control batteries when You purchase the air conditioner The remote control does not work correctly gt Use two AAA LROS 1 5V batteries Do not use old batteries or different kinds of batteries together Batteries may be completely discharged after 12 months even if they have not actually been used 1 Push the battery cover on the rear of the remote control with your thumb in the direction of the arrow and remove it 2 Insert the two batteries taking care to respect the polarities on the battery with on the remote control on the battery with on the remote control 3 Close the cover by sliding it back until it clicks into
18. place Cooling Your Room You must select the Cool mode if you wish to lower the temperature Remote Control Control Panel in your room You can also set the fan speed 1 Press the On Off button Result The air conditioner starts up in the mode selected when the unit was last used The unit beeps twice The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 If the temperature is not displayed on the control panel Press the COOL button on the remote control or Press the Mode button on the unit one or more times until the temperature is displayed Result The unit beeps each time you press the COOL Mode button The air conditioner starts up in the Cool mode gt You can change modes at any time 3 To adjust the temperature press the Temperature buttons on the remote control or unit one or more times until the desired temperature is displayed The temperature can be set between 64 F and 86 F Result Each time you press the temperature buttons The temperature is adjusted by 1 F and displayed on the control panel The unit beeps The air conditioner starts cooling if the room temperature is higher than the selected temperature 4 To set the fan speed Press the HIGH MED or LOW button on the remote control as desired Ti
19. rd double hung type Clear vertical opening of 12 7 8 minimum from bottom of sash to sill Install the air conditioner in a window where there will be enough clearance around the cabinet to allow ample circulation of air through the unit gt All supporting parts should be secured to firm wood masonry or metal Window installation Tools needed Philips head screwdriver Ruler or tape measure Adjustable wrench Pencil Scissors Parts furnished Type Name of part arty Type Name of part Qty Type Name of part Long wood screw 5X16 Top support channel Window filler panel S Window bracket 1 Install the top support channel with three Type B screws provided i i support gt The screw holes are larger gauge on the channel and smaller on the cabinet The top support channel is L shaped The high side of the channel must always face inwards 2 Assemble the window brackets on the cabinet 2 1 Loosen the lower screw slightly on each side of the cabinet and install the Type C window bracket 2 2 Tighten the screws securing the brackets Window bracket Type C 3 Attach the window filler panels to the unit 3 1 Slide the window filler panels and their frames into the channels on the top and bottom of the cabinet 3 2 Assemble the window filler panels to the cabinet using six Type B screws
20. rized service center SAMSUNG will repair or replace any part found to be defective at no charge as stipulated herein with new or reconditioned parts during the limited warranty period specified above To request warranty service the purchaser must contact SAMSUNG for problem determination and service procedures SAMSUNG does not warrant uninterrupted or error free operation of the product All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG Replacement parts and products assume the remaining original warranty or ninety 90 days whichever is longer This limited warranty covers manufacturing defects in materials and workmanship encountered in normal noncommercial use of this product and shall not apply to the following including but not limited to delivery and installation damage which occurs in shipment applications and uses for which this product was not intended failures or problems which are caused by products or equipment not supplied by SAMSUNG accidents misuse abuse neglect misapplication fire water lightning or other acts of nature incorrect electrical line voltage fluctuations or surges damage caused by improper or faulty installation product alteration or modification improper or unauthorized repair cosmetic damage or exterior finish product with altered serial numbers failure to follow operating and environmental instructions that are covered and prescribed in the instruction
Download Pdf Manuals
Related Search