Samsung AQ30BAN User Manual
Contents
1. Center WebSite SOUTH AFRICA 0860 726 7864 SAMSUNG 800SAMSUNG 7267864 UAE www samsung com mea 8000 4726 Samsung Electronics Co Ltd All Rights Reserved2. control the direction of the air flow refer to pages 16 and 17 On Timer Off Timar Heating Your Room SET TEMP Sail On Timer Off Timer Turbo On Timer You must select the Heat mode if you wish to adjust the Heating temperature Fan speed when heating 1 If necessary press the On Off button Result The 5 Way indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 Ifthe Ke is not displayed at the top of the remote control press the MODE button on the remote control one or more times until it appears Result The indoor unit beeps each time you press the MODE button The air conditioner runs in HEAT mode Note You can change modes at any time 3 To adjust the temperature press the TEMPERATURE buttons one or more times until the required temperature is displayed Possible temperatures are between 16 C and 30 C inclusive Result Each time you press the TEMPERATURE buttons The temperature is adjusted by 1 C The indoor unit beeps The air conditioner starts heating provided that the room temperature is lower than the desired tempera
3. 4 The Sleep Timer can be used when you are cooling or heating your room to switch the air conditioner off automatically after a period of six hours Note If you wish to switch the unit off at a specific time refer to page 19 1 Make sure that you have selected either COOL or HEAT mode 2 Press the button one or more times until appears on the remote control Result The indoor unit beeps The air conditioner will be controlled as indicated in the illustrations below Cooling The desired temperature is increased by 1 C every hour When it has been increased by 2 C after two hours the Set temperature is maintained for TEMP four hours rari Stop Heating The desired temperature is decreased by 1 C every hour Start Stop When it has been decreased Set To Cancel the Sleep Timer by 2 C after two hours the temperature is maintained for four hours TEMP If you no longer wish to use the Sleep Timer that you have set you can cancel it at any time Press the s button Result e The indoor unit beeps The C is no longer displayed The air conditioner operates normally Operating Recommendations ENGLISH Here are a few recommendations that you should follow when using your air conditioner Topic Recommendation Heating performances The heat pump inside the air conditioner absorbs heat from outside air and brings it indoors If the temperature of th
4. period of time You can set the period of time from 30 minutes to 24 hours 1 To set the operating time press the OFF TIMER button one or more times until the required time is displayed Possible time is between 0 5 hour and 24 hour inclusive 30 2 Press the 56 Set Cancel button to complete the setting g Result The remaining time is displayed Blinking of the timer indicator stops The air conditioner will switch off automatically when the counter displayed on the remote control reaches the set time and disappears the Off timer setting E ej Sample If you would like to turn the air conditioner on after 2 hours and to operate it for 2 hours 1 Press the ON TIMER button until 2 0 Hr is displayed 2 Press the C9 Set Cancel button 3 Press the OFF TIMER button until 4 0 Hr is displayed 4 Press the C9 Set Cancel button Note You can see or change the setting mode and or the temperature by pressing the MODE button or the TEMPERATURE buttons after setting the Off timer tI To Cancel the Off Timer 1 To cancel the Off Timer press the OFF TIMER button one or more times until the timer setting disappears 2 Press the 0 Set Cancel button e Note If you want to turn off the air conditioner before the timer reaches Oy the setting time press the ON OFF button S way N 2 Setting the Sleep Timer ge
5. e comfortable circumstances You can use the 5 Way function with the indoor unit as well as the remote control Thus you can use this function even though you have lost your remote control Using with the indoor unit 1 Press the 1 ON OFF button one time and then select the desired mode To obtain a n Then select 0 5 B Normal operating STANDARD mode Reducing the uncomfortable temperature gradually High fan speed POWER mode Compressor run time reduced SAVING mode Fan speed reduces as the temperature SILENCE mode decreases 2 To stop the operating press the 1 ON OFF button until all indicators turn off Note Even if the air conditioner has been turned on via the ON OFF button on the unit operations can still be controlled using the remote control as usual Selecting with the Remote Control To select the 5 Way function with the remote control press the 5 Way button one or more times until the desired mode is selected On Timer Each time you press the 5 Way button Off Timer RP gt b 8 AD 3 di Each 5 Way indicator on the indoor unit lights up in order S Way lt Selecting the Automatic Operating Mode You can start the air conditioner in Automatic mode from your remote control In the Automatic mode the standard temperature and the optimum fan speed is selected automatically You can adjust the standard tem
6. e modes at any time Turbo 3 To adjust the temperature press the TEMPERATURE buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each you press the TEMPERATURE buttons temperature is adjusted by 1 C LAY The indoor unit beeps n QD The air conditioner starts removing the excess humidity E g the quantity of air is adjusted automatically Turbo 4 To control the direction of the air flow refer to pages 16 and 17 Airing Your Room If the atmosphere in your room is stale you can air the room using the Fan feature 1 If necessary press 20 On Off button Result The 5 Way indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps ENGLISH On Timer Off Timer 4 5 O IR 2 If the of is not displayed at the top of the remote control press the MODE button on the remote control one or more times until it appears Result The indoor unit beeps each time you press the MODE button The air conditioner runs in FAN mode The temperature is set automatically Note You can change modes at any time 3 Select the fan speed by pressing the FAN button one or more times until the required setting is displayed va Low Sal Medium ul High Result Each tim
7. e outside air drops the air conditioner will heat less If you find that the room is not warm enough use an additional heating appliance Warm air circulation The air conditioner circulates warm air to heat your room as a result some time will be required after starting the air conditioner to warm the entire room If necessary set the air conditioner on before you wish to use the room Frost When outside temperatures are low and humidity is high frost may form in the outdoor unit when heating is selected If this happens The heating operation is stopped The Deice mode is triggered automatically for about seven minutes No intervention is required from you after about seven minutes the air conditioner starts operating again normally High indoor and outdoor If both the indoor and outdoor temperatures temperatures are high and you select the Heat mode the outdoor unit s fan and compressor may stop at times This is normal simply wait until the air conditioner switches on again Power failure If a power failure occurs when the air conditioner is operating the unit is switched off When the power returns C1 you must press the ON OFF button to restart it AQ30BA the air conditioner KKC2 K starts up again automatically Mote sure which model you have purchased because some air conditioners do not restart automatically Temperature and Humidity Ranges The following tab
8. e you press the FAN button the indoor unit beeps 4 To control the direction of the air flow refer to pages 16 and 17 Turbo Sul lt OnTimr Jj Adjusting the Air Flow Direction Vertically Depending on the position of the indoor unit on the wall of your room you can adjust the position of the outer air flow blade on the bottom of the unit thus increasing the efficiency of the air conditioner 1 Press the SWING button one or more times as required Result The outer blade is adjusted vertically RECOMMENDATION When Adjust the blade to face Cooling Upwards Heating Downwards On Timer g Off Timer 2 If you want the blade to move up and down automatically when the air conditioner is operating press the SWING button Result The blade move up and down around the base position set 3 To stop the blade moving up and down press the SWING button again Note fyou switch the air conditioner Then the blade is Off Closed completely On again Set to the initial position powered Adjusting the Air Flow Direction Horizontally ENGLISH There are two sets of inner air flow blades J ust as the outer air flow blade can be adjusted vertically the inner blades can be adjusted horizontally 1 Adjust each set of inner blades to the required position by pushing or pulling them sideways Setting the On Timer The On Timer enables you to swi
9. ed for your air conditioner and contact your installation specialist Make sure that the unit is correctly ventilated at all times Do not place clothing or other materials over it Ifthe wireless remote control will not be used for a long time remove the batteries If applicable When using a wireless remote control the distance should not be more than 7 meters from the air conditioner If applicable DISPOSING or THE UNIT Before throwing out the device it is necessary to pull back the battery yug c E cells and get rid of them safely for recycling reasons When you need to dispose of the unit consult your dealer If pipes are removed incorrectly refrigerant may blow out and come into contact with your skin causing injury Releasing refrigerant into the atmosphere also damages the environments Please recycle or dispose of the packaging material for this product in an environmentally responsible manner OTHERS Never store or ship the air conditioner upside down or sideways to nrc avoid damage to the compressor The appliance is not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure that they do not play with the appliance current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency Contents PREPARING YOUR AIR CONDITIONER m Safety Precautions ene
10. eg USERS MANUAL ENGLISH Indoor unit Outdoor unit AQT30C1 C2 BB UOT30C1 C2 BB AQT30CT C2 BBD UOT30C1 C2 BBD AQT32C1 C2 BE UOT32C1 C2 BE 2 AQT32C1 C2 BED UOT32C1 C2 BED 5 D lt z lt or L Split type Air Conditioner Cooling and Heating EE DB98 03438A 5 Register your product at www samsung com global register Safety Precautions The following safety precautions must be taken when using your air conditioner AN WARNING Risk of electric shock e Can cause injury or death Disconnect all remote electric power supplies before servicing installing or cleaning e This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard DURING OPERATION Users of this product are cautioned not to attempt repair of this product Wath eec aoe at their own discretion Instead they are requested to directly contact a designated service center or the outlet at which the product was purchased Never spill any kind of liquid into the unit Should this happen unplug or main switch off the unit and contact an authorized service center Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury Keep children away from the unit Do not place any obstacles in front of the unit Do not spray liquid of any kind into the indoor unit Should this happen switch off the breaker us
11. ioner starts up in the mode selected when the unit was last used Ofi Time The indoor unit beeps 9 PORTANT The air conditioner is fitted with a protection mechanism to SCH prevent the unit from being damaged when it is started G way immediately after being Plugged in Stopped It will start up normally after three minutes 2 Ifthe X is not displayed at the top of the remote control press the MODE button on the remote control one or more times until it appears ES Result The indoor unit beeps each time you press the MODE button g The air conditioner runs in COOL mode Note You can change modes at any time Turbo 3 To adjust the temperature press the TEMPERATURE buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each you press the TEMPERATURE buttons The temperature is adjusted by 1 C The indoor unit beeps The air conditioner starts cooling provided that the room temperature is higher than the selected temperature the fan will however operate BS AI A Turbo 4 Select the fan speed by pressing the FAN button one or more times until the required setting is displayed erf Automatic rotated f gt ur gt Sul DAP Low er Medium Sul High ull Result Each time you press the FAN button the indoor unit beeps full g Turbo 5
12. ir conditioner Please take the time to read it as it will help you take full advantage of the unit s features The booklet is organized as follows The following figures are shown on pages from 4 to 6 Indoor and outdoor units Remote control buttons and display They will help you find the buttons and understand the symbols displayed Inthe main part of the installation book you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use three different symbols HOLD DOWN ENGLISH Inserting the Remote Control Batteries You must insert or replace the remote control batteries when You purchase the air conditioner The remote control does not work correctly Note Use two AAA LRO3 1 5V batteries Do not use old batteries or different kinds of batteries together Batteries may be completely discharged after 12 months even if they have not actually been used 1 Push the battery cover on the rear of the remote control with your thumb in the direction of the arrow and remove it 2 Insert the two batteries taking care to respect the polarities on the battery with on the remote control on the battery with on the remote control 3 Close the cover by sliding it back until it clicks into place 5 Way Function ENGLISH You can select the 5 Way function with operating mode of the air conditioner for mor
13. le indicates the temperature and humidity ranges within which the air conditioner can be used If the air conditioner is used at Then High temperatures The automatic protection feature may be triggered and the air conditioner stopped Low temperatures Awater leak or some other malfunction may occur if the heat exchanger freezes High humidity levels Water may condense on and drip from the surface of the indoor unit if it is used for long periods Mode Outdoor Temperature Indoor Temperature Indoor Humidity Heating 0 to 24 C approx 27 or less Cooling 21 C to 43 C approx 18 C to 32 C approx 80 or less Drying 18 C to 43 C approx 18 C to 32 C approx Ifthe outdoor temperature is as low as the heating capacity drops up to 70 80 depending on the operating condition If the cooling operation is used at over 33 C indoor temperature it does not cool at its full capacity Cleaning Your Air Conditioner To get the best possible use out of your air conditioner you must clean it regularly to remove the dust that accumulates on the air filter PORTANT Before cleaning your air conditioner ensure that you have switched off the breaker used for the unit 1 Open the front grille by pulling on the tabs on the lower right and left sides of the indoor unit 2 Disassemble the front grille by pulling it forwards 3 Lift out the bottom edge of the air filters and pull down to release them 4 Re
14. move all dust on the air filters with a vacuum cleaner or brush 5 When you have finished insert the top part of the filters into their slot and push down on the bottom edge until they click into place 6 Clean the front panel with a damp cloth and mild detergent do NOT use benzene solvents or other chemicals Front grille Body groove If you have not used the air conditioner for a long period of time set the fan going for three to four hours to dry the inside of the air conditioner thoroughly Solving Common Problems Before contacting the after sales service perform the following simple checks ENGLISH They may save you the time and expense of an unnecessary call Problem Explanation Solution The air conditioner does not operate at all Check that the breaker used for the air conditioner is switched on Check that the 5 Way indicator on the indoor unit is on if necessary press the On Off button on the remote control Check whether the TIMER indicator on the indoor unit is switched on If so Wait until the switch on time is reached and the air conditioner starts up automatically Cancel the timer see pages 18 and 19 for further details The air conditioner does not operate with the remote control Check that there are no obstacles between you and the indoor unit Check the remote control batteries Check that you are close enough to the indoor unit seven me
15. n Off amp 5 Way selection button Remote Control Sensor TIMER indicator STANDARD inus F NATURE indicator SILENCE indicator SAVING indicator POWER indicator Note For details on the 5 Way refer to page 9 S 3 ENGLISH Zeg Unit UQT30C1 C2 BB UQT32C1 C2 BE Air Inlet Rear Air Outlet Connection Valve Outdoor Unit UQ30BA UQT30C1 C2 BBD UQT32C1 C2 BED Air Inlet Rear Air Outlet Connection Valve Remote Control Buttons and Display Remote control transmission indicator Operating mode 6 AUTO COOL C DRY oh FAN XX HEAT Temperature setting Turbo mode Sleep mode Fan speed Air flow direction On Timer setting Off Timer setting Battery discharge indicator 5 Way selection button SH Ea SET TEMP MED umo C E t LS l Pall 2 ON TIMER r v se OFF TIMER I DI len a a 5 Mode selection button AUTO COOL DRY FAN HEAT Temperature adjustment buttons Turbo Sleep mode selection button Fan speed adjustment button Swing button On Timer button Off Timer button On Off amp Timer Set Cancel button Getting Started You have just purchased split type air conditioner and it has been i installed by your installation specialist Your Owner s Instructions contains valuable information on using your a
16. perature but not the fan speed 1 If necessary press the On Off button Result The 5 Way indicator on the indoor unit lights up On Timer The air conditioner starts up in the mode selected when the unit was last used Off Timer The indoor unit beeps Gj 4 PORTANT The air conditioner is fitted with a protection mechanism to 701 prevent the unit from being damaged when it is started G way immediately after being Plugged Stopped It will start up normally after three minutes 2 Ifthe ab is not displayed at the top of the remote control BA press the MODE button on the remote control one or more times until it appears Result The indoor unit beeps each time you press the MODE button The air conditioner runs in AUTO mode Turbo Note You can change modes at any time 3 To adjust the standard temperature The air conditioner automatically set the standard temperature by the current room temperature press the TEMPERATURE buttons one or more times SET TEMP SET TEMP SET TEMP SET TEMP C 2 1 Standard temperature 1 2 GQ lt When you feel hot gt lt When you feel chilly gt Turbo Cooling Your Room ENGLISH You must select the Cool mode if you wish to adjust the Cooling temperature Fan speed when cooling 1 If necessary press the On Off button Result The 5 Way indicator on the indoor unit lights up On Timer The air condit
17. s reset automatically to the previous mode temperature and fan settings But if you press the amp amp button in DRY or FAN mode it will change to AUTO mode automatically 3 If you wish to stop the Turbo function before the end of the 30 minute period press the button one or more times until or disappears Result air conditioner is reset automatically to the previous mode temperature and fan settings 4 To control the direction of the air flow refer to pages 16 and 17 On Timer Off Timer GO ENGLISH Removing Excess Humidity If the atmosphere in your room is very humid or damp you can remove excess humidity without lowering the room temperature too much 1 If necessary press On Off button On Timer Result The 5 Way indicator on the indoor unit lights up The air conditioner starts up in the mode selected when Off Timer the unit was last used The indoor unit beeps og PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 Ifthe e is not displayed at the top of the remote control press the MODE button on the remote control one or more times until it appears Result The indoor unit beeps each time you press the MODE button The air conditioner runs in DRY mode Note You can chang
18. tch on the air conditioner automatically after a given period of time You can set the period of time from 30 minutes to 24 hours 1 To set the operating time press the ON TIMER button one or more times until the required time is displayed Possible time is between 0 5 hour and 24 hour inclusive JL D Off Timer 2 Press the 0 button to complete the setting Result The remaining time is displayed Blinking of the timer indicator stops The selected mode and the temperature on the display JL disappear after 10 seconds The air conditioner will switch on automatically when the AL counter displayed on the remote control reaches the set time and disappears the On timer setting ai E To select an operating mode in advance press the Ces button until the desired mode is displayed at the top of the remote control Result The air conditioner will run in the selected mode when it is turned CH To Cancel the On Timer 1 To cancel the On Timer press the ON TIMER button one or more times until the timer setting disappears On Ti rm Off Timer 2 Press the 0 Set Cancel button Note Ifyou want to turn on the air conditioner before the timer reaches the setting time press the ON OFF button cel O l Setting the Off Timer ENGLISH The Off Timer enables you to switch off the air conditioner automatically after a given
19. tres yards or less No beep is heard when you press the On Off on the remote control Check that you are pointing the remote control at the remote control sensor in the right of the indoor unit Replace the remote control batteries if necessary The air conditioner does not cool or heat Check that the correct operating mode has been selected AUTO COOL HEAT The room temperature may be too low or too high Dust may be blocking the air filter guard refer to page 22 for cleaning instructions Check that there is no obstacle in front of the outdoor unit When heating the required room temperature is never reached and the air conditioner frequently stops The fan speed does not change when you press the FAN button Check that required temperature has been set correctly Increase the fan speed If the air flow is directed downwards use the remote control to direct it upwards Check that the operating mode is set to COOL HEAT or FAN in the AUTO mode the fan speed changes automatically and in the DRY mode it is set to AUTO The air flow direction does not change when you press the Check that the air conditioner has been switched on if necessary press the On Off button on the remote control SWING button The timer is not correctly triggered Check that the timer has been programmed correctly see pages 18 and 19 Odours are permeated the room Air the room d
20. ture selected temperature 3 C the fan will however operate 4 Select the fan speed by pressing the FAN button one or more times until the required setting is displayed al Automatic rotated Sut gt Pull Ti Low Sl Medium sP al Result Each you press the FAN button the indoor unit beeps For the first three to five minutes the fan operates very slowly until the air has been sufficiently warmed Once the correct temperature has been reached the fan is automatically set to the required speed 5 control the direction of the air flow refer to pages 16 and 17 Changing the Room Temperature Quickly The Turbo cooling heating function is used to cool or heat your room as quickly as possible Example You have just come home and find that the room is very hot You wish to cool it down as quickly as possible The Turbo function operates for 30 minutes with the maximum settings before retuming automatically to the mode and temperature previously selected 1 If necessary press the button Result The 5 Way indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps 2 Press the Gut button Result The temperature and fan settings are adjusted automatically The air conditioner cools or heats the room as quickly as possible After 30 minutes the air conditioner i
21. un eena m View of enn m Remote Control Buttons and Display m Getting Started m Inserting the Remote Control Batteries OPERATING YOUR AIR CONDITIONER m 5 Way Function m Selecting the Automatic Operating Mode m Cooling Your Room m Heating Your Room m Changing the Room Temperature Quickly m Removing Excess Humidity m Airing Your Room m Adjusting the Air Flow Direction Vertically m Adjusting the Air Flow Direction Horizontally PROGRAMMING YOUR AIR CONDITIONER m Setting the On Timer m Setting the Off Timer _ m Setting the Sleep Timer RECOMMENDATIONS FOR USE m Operating Recommendations m Temperature and Humidity Ranges m Cleaning Your Air Conditioner m Solving Common Problems m Installing a Filter Option TECHNICAL SPECIFICATIONS ENGLISH View of the Unit Indoor Unit The design and shape are subject to change according to the model Air filter Air Inlet Under the gne Air flow blades outlet O
22. uring air conditioning The air conditioner makes a hollow Since this air conditioner is a heat pump model there can be hollow sound when it is turned on or off sound caused by flow of refrigerant when you turn the air conditioner on off The sound is not a defect of the air conditioner and it does not affect the cooling heating capacity Installing a Filter Option Deodorizing filter Bio Pure Filter The air conditioner can be fitted with a deodorizing and Bio Pure filter to remove minute dust particles or odours The service life of the filter is approximately three months depending on the time during which the air conditioner is used 1 Remove the vinyl packing from the filter Note not remove the packing from a deodorizing filter until you wish to use the filter as it will lose its properties 2 Insert the filter in the filter holder and press the three insert tabs until you hear a click 3 Open the front grille by pulling on the tabs on the lower right and left sides of the indoor unit 4 Take out the existing filter and replace it with the new one Technical Specifications ENGLISH Model Indoor unit Power Supply AQ30BA AQT30C1 C2 BB 220V 60Hz AQT30C1 C2 BBD AQT32C1 C2 BE shane 208 7 AQT32C1 C2 BED ELECTRONICS Contact SAMSUNG WORLD WIDE If you have any comments or questions regarding a Samsung product contact the SAMSUNG customer care center Customer
Download Pdf Manuals
Related Search