Samsung AWT18P1HBB User Manual
Contents
1. OWNER S INSTRUCTIONS AWT12P1HEA AWT12P1HBA AWT18P1HBA BB AWT18U1HBA BB AWT18P1HEA EB AWT18U1HEA EB AWT24P1HBA BB AWT24U1HBA BB AWT24P1HEA EB EC AWT24U1HEA EB EC Window type Room Air Conditioner Cool m vu un NE I EX DB98 17027A 4 Safety Precautions The following safety precautions must be taken when using your air conditioner AN WARNING DURING OPERATION DISPOSING OF THE UNIT OTHERS Risk of electric shock e Can cause injury or death e Disconnect all remote electric power supplies before servicing installing or cleaning e This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard Users of this product are cautioned not to attempt repair of this product at their own discretion Instead they are requested to directly contact a designated service center or the outlet at which the product was purchased Never spill any kind of liquid into the unit Should this happen unplug or main switch off the unit and contact an authorized service center Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury Keep children away from the unit Do not place any obstacles in front of the unit Do not spray liquid of any kind into the indoor unit Should this happen switch off the breaker used for your air conditioner and contact your installation specialist Make sure that the2. front panel 3 Reassembling of front grille should be done in reverse order of disassembly 2 Pullthe air filter to the right side 3 Remove all dust on the air filter with a vacuum cleaner or brush 4 When you have finished insert the air filter back into its original position 5 Wipe the surface of the unit with a neutral detergent and then wipe it again with dry cloth Be sure not to use benzene solvent or other chemical products gt Ifyou Then Will not be using the air conditioner for a long period of time 9 Set the fan going for three to four hours to dry the inside of the air conditioner thoroughly Switch the air conditioner off and unplug it from the wall socket Clean the filter and outer surfaces Have not used the air conditioner for a long period of time Set the fan going for a few hours to dry the inside of the air conditioner thoroughly Solving Common Problems Before contacting the after sales service perform the following simple checks They may save you the time and expense of an unnecessary call PROBLEM EXPLANATION SOLUTION The air conditioner does not operate at all The air conditioner does not Check that the circuit breaker used for the air conditioner has not been triggered Check that the power cable is plugged into a wall socket and the socket is switched on if necessary Check that the correct operating mode has been selected coo
3. In the case of an area where the drain pan can be directly installed on the rear side of the unit after installing the air conditioner Follow steps 5 and 6 only If the air conditioner has accessory seal please install the seal as shown in the figure Installation of the accessory seal Except AWT12 Seal Cabi Side T40 W50 L430 Qty 2 Seal Cabi Top T30 W40 L700 Qty 1 Seal Base T10 W30 L630 Qty 1 Drain Pan lll Nise cap Screw Drain Hose Bottom Side View with Drain Pan and Hose in Place m ANN ML 7 un I SK Screw SEAL BASE SEAL CABI TOP SEAL CABI SIDE SEAL CABI SIDE THIS AIR CONDITIONER IS MANUFACTURED BY LIT ELECTRONICS
4. an feature and if necessary evacuate the stale air outside 1 If you wish to evacuate stale air outside push the ventilation lever on the front of the unit to the right and the open position SM Result The air inside the room circulates and stale air is evacuated outside Otherwise push the ventilation lever to the left and the closed position Result The air simply circulates inside the room 7 Z 2 Set the operating mode selection dial to the Hi Fan Med Fan or Low Fan position gt HiFan The fan turns high speed Med Fan The fan turns med speed Low Fan The fan turns low speed Result The air conditioner starts up in Fan mode Operation dazu 3 To control the direction of the air flow refer to page 8 AWT12 Operation dh AWT18 AWT24 Switching the Air Conditioner Off Off m L You can switch the air conditioner off whenever you want 1 To switch the unit off simply set the operating mode selection dial to the off position Result The air conditioner stops operating Mid di Cool Basis Operation Jail ANNE Operation Jeius AWT18 AWT24 Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room you can adjust the orientation of the inner air flow blades on the right hand side of the unit thus increasing the efficiency of the air conditioner 1 Setthe air flow blade swing switch to the On positio
5. conditioner can be used Mode Indoor Outdoor Indoor Humidity Temperature Temperature Cooling 21 C to 32 C approx 21 C to 54 C approx 80 or less If the air conditioner is used at Then Higher temperature The automatic protection feature may be triggered and the air conditioner stopped Lower temperature A water leakage or some other malfunction may happen if the heat exchanger freezes Higher humidity levels Water may condense on and drip from the surface of the unit if it is used for long periods Cleaning Your Air Conditioner IN Front grille Grille groove Body guide The air conditioner has two or three grille grooves depending on the model Be sure to clean the air filter periodically two weeks to maintain the air conditioner in the best condition for a long period of time a When cleaning the air conditioner turn it off and pull out the power plug 1 Hold the air filter handle slightly pull it to the left side and open the front grille gt The removal of the front grille makes it easier to clean the air conditioner Open the grille as much as possible CAUTION Removal and reassembly of the Front Grille 1 Grasp the lower part of the front grille and the front grille handle then open the grille The open angle of front grille has not to be exceeded 25 degree 2 Lift the front grille slightly and remove it from the
6. he main parts and controls on the unit In the manual you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use four different symbols A gt IMPORTANT NOTE Cooling Your Room You must select the Cool mode if you wish to lower the temperature Off gy ste in your room You can also set the fan speed Low Hi Fan e Fan 1 Select the operating mode and fan speed dsgja ag Ma au To cool your room Set the operating mode with a selection dial to Low Hi Cool e Cool High fan speed Hi Cool xm mue us Between High and Low Med Cool coo ee Low fan speed Low Cool Operation Jae Result The air conditioner starts up in Cool mode TTT The fan starts up at the speed selected gt You can change modes at any time Operation Jetis AWT18 AWT24 27 C 23 icm 2 To adjust the temperature turn the temperature control dial to the desired position Possible temperatures Between 18 C and 29 C inclusive i eo Result The air conditioner starts cooling if the room temperature is higher than the selected temperature 10Coole Thermostat 3 To control the direction of the air flow refer to page 8 lysfl a 5 kaia AWT12 27 C 23 C 27 N C 29C 18C 10 Coolest tt lal a a obia AWT18 AWT24 Airing Your Room If the atmosphere in your room is stale you can air it using the F
7. it after installing the air conditioner Example High storage 1 Open the front grille CAUTION Removal and Reassembly of the Front Grille 1 Grasp the lower part of the front grille and the air filter handle then open the grille The open angle of front grille has not to be exceeded 90 degree 2 Push the front grille on the left and remove it from the front panel 3 Reassembling of front grille should be done in reverse order of disassembly 2 Remove the front panel 2 1 Press both sides of the cabinet in the direction of the arrow as shown in the figure 2 2 Pull the lower part of the front panel slightly forward below three inches 2 3 Lift the front panel upward Zn 34 A Applying excessive force to remove the front panel may cause damage to the tab be sure not to use excessive force 3 Remove two screws on the lower right and left sides of the unit Method of Installation Cont Remove the chassis from the cabinet Remove the rubber cap inserted into the basepan Fix the drain pan as shown in the figure and then connect the drain hose You can use any commercially available drain hose Install the cabinet at the specified area after installing the drain pan and then re assemble it in the original condition 3 When assembling the front panel be sure to fix with a supplied screw TH 2S 4X10
8. ling or airing Check that the correct operating mode has been selected cool The room temperature may be too low Dust may be blocking the air filter refer to page 10 for cleaning instructions Check that there is no obstacle blocking the air flow into or out of the unit The air flow direction does not change when you set the air flow blade swing switch to the On position Check that the air conditioner has been switched on if necessary turn the operating mode selection dial Odour is permeated in the room during air conditioning Air the room Technical Specifications Design and specifications are subject to change without notice Model Power Supply AWT12P1HBA AWT18P1HBA BB AWT18U1HBA BB AWT24P1HBA BB AWT24U1HBA BB 22 AWT12P1HEA AWT18P1HEA EB AWT18U1HEA EB 220V 240V 50Hz AWT24P1HEA EB EC AWT24U1HEA EB EC Method of Installation Before installation be sure to check the installation area for the air conditioner and installation method of the drain hose Checkpoints prior to installation 1 Check the cabinet and front grille of the unit for any harmful defects such as scratches 2 Be sure to check the power supply Refer to the specifications on the label attached to the unit Installation Conditions 1 As the unit is heavy the wall or window of the installation area should have sufficient strength and durability for operation of the air conditioner and f
9. n Result The inner blades swing automatically left and right Off On slau Jua Air Swing elgall gjga 2 To stop the blades moving left and right set the air flow blade swing switch to the off position Off oi gt To stop the blades in a specific position and orient the air flow in the ET ii i 2 s s Air Swin corresponding direction simply set the switch to the off position 9 e when the blades are in the desired position Adjusting the Air Flow Direction Vertically Again depending on the position of the unit in your room you can adjust the orientation of the outer air flow blades on the right hand side of the unit RECOMMENDATION When Adjust the blades to face Cooling Upwards Adjust the air flow blades to the desired position by pushing them upwards or downwards SSN SSN gt If you orient the air flow blades downwards and the unit operates in Cool mode for long periods of time dew may Form on the surface of the blades Drip from the blades AI Operating Recommendation Here is a recommendations that you should follow when using your air conditioner Topic Recommendation Power failure If a power failure occurs when the air conditioner is operating the unit is switched off When the power returns the air conditioner starts up again automatically Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air
10. or prevention of any vibration or noise If it is weak reinforcement work should be performed separately 2 It is advisable to install the air conditioner in the north or west side to prevent the effect of direct sunlight When installing it in the south or east side due to unavoidable circumstances it is advisable to install the sunshade to prevent the direct sunlight In this case take care not to cause any hindrance to the flow of outside air 3 When installing the air conditioner be sure to obtain sufficient space on the rear side of the unit for smooth flow of air When operating the air conditioner in closed areas such as inner building with cooling operation and result in trouble with the unit See the illustration below Fence wall C 500mm gt 4 900mm or other obstacle L Approx 3 750mm 150mm min gt If the wall is greater than 150mm thick cut the wall back on a 45 angle if possible MODEL A AWT12 170 AWT18 AWT24 260 2200 Outdoor side 45 EN p Indoor side 100mm or more Method of Installation Cont Installation of the Drain Tube Fix the drain tube as shown in the figure Installation of the Drain Pan The procedure for installing the drain pan should be determined by the condition of the installing area In the case of an area where the drain pan can not be directly installed on the rear side of the un
11. sesaesesaeess 13 Air Conditioning Unit Main Parts and Control Panel The design and shape are subject to change depending on the model Inner air flow blades right left orientation Outer air flow blades Air inlet Inside up down orientation Air filter Inside Air inlet Outside SN Ventilation lever SSN Power Cable AWT18 AWT24 AWT12 Power plug The type of the power plug may differ according BLUE BROWN YELLOWIGREEN 3 Power cable connection to the type of local power should be committed to supply Main Power Fann an installation engineer AWT12 AWT18 AWT24 Off gs Operating mode N Temperature Operating mode selection dial fv i control dial selection dial Med e Thermostat hall s gt ia Cool Eik Operation on dum ots Off Air Swingfisall ci Air flow blade swing switch Air flow blade swing switch Getting Started You have just purchased a window type room air conditioner and it has been installed by your installation specialist Your Owner s Instructions contain much valuable information on using your air conditioner Please take the time to read them as they will help you take full advantage of the unit s features The booklet is organized as follows The illustration on page 4 shows the air conditioning unit it indicates the location and purpose of t
12. the environments Please recycle or dispose of the packaging material for this product in an environmentally responsible manner Never store or ship the air conditioner upside down or sideways to avoid damage to the compressor The appliance is not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure that they do not play with the appliance Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency Contents PREPARING YOUR AIR CONDITIONER m Safety Precautions nece ean eed aaa 2 m Air Conditioning Unit Main Parts and Control Panel pp 4 a Getting Started eroe REI a DRE BE 5 OPERATING YOUR AIR CONDITIONER m Cooling Your ROOM sc ins e Eee PER eite e ERE xU S 6 E Airing Your ROOM s onn e dek ndera vidat a eh ais ie ns det 7 m Switching the Air Conditioner Off aaaaaaanaaanaaaan nanen ne see eee ee vere z vere vere eee ce veren eee 7 m Adjusting the Air Flow Direction Horizontally pp 8 m Adjusting the Air Flow Direction Vertically pp 8 RECOMMENDATIONS FOR USE Operating Recommendation pp 9 m Temperature and Humidity Ranges pp 9 m Cleaning Your Air Conditioner pp 10 m Solving Common Problems pp 11 m Technical Specifications ssesseseseseeeeeeeeennennee nennen 12 METHOD OF INSTALLATION cccecsssescsscecseeseseescseceesecsesessesesseeesaeessesesse
13. unit is correctly ventilated at all times Do not place clothing or other materials over it If the wireless remote control will not be used for a long time remove the batteries If applicable When using a wireless remote control the distance should not be more than 7 meters from the air conditioner If applicable The air conditioner must be plugged into its own specific power source which must be installed in compliance with national wiring earthing and safety regulations If the power cord is damaged in any way it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard This device must be installed according to the national electrical rules The appliance must be installation that the plug should be easily accessible after installation If the fuse on PC board is broken please change it with the type of T 3 15A 250V The breaker of the air conditioner should be all pole switch and the distance between its two contacts should be no less than 3 5mm Such means for disconnection must be incorporation in the fixed wiring Before throwing out the device it is necessary to pull back the battery cells and get rid of them safely for recycling reasons When you need to dispose of the unit consult your dealer If pipes are removed incorrectly refrigerant may blow out and come into contact with your skin causing injury Releasing refrigerant into the atmosphere also damages
Download Pdf Manuals
Related Search