Samsung AQV36JANKCV User Manual
Contents
1. If the good sleep mode is set for less than 4 hours the operation will stop at the set time If the good sleep mode is set for over 5 hours the last hour will run in Waking Up stage before shutting off Recommended set temperature is between 77 F 81 F for cooling and 69 8 F 73 4 F for heating Cool mode Temp 4F 2 F Set temperature When the 8 hour cycle completes this section Kag repeats 4 F 1 2 3 4 5 6 7 8 Time hr Heat mode When the 8 hour cycle completes this section repeats 1 2 3 4 5 6 7 8 Time hr Selecting the Turbo Function You can select the Turbo Function if you want to cool or heat your room in the fastest way After the 30 minute operation with the maximum setting it returns to the previous setting POWER 1 Ifnecessary press the On Off button Result The operation indicator on the indoor unit lights up Theair conditioner starts up in the mode you selected last The indoor unit beeps TURBO Press the O button TURBO POWER 2 O Result The temperature and fan settings are adjusted automatically Theair conditioner cools or heats the room as quickly as possible Pama MANE After 30 minutes the air conditioner is reset automatically to the previous setting You can select the Turbo function in the Auto Cool and Heat mode If you select this function in the Dry or Fan mode the mode changes to the Auto mode TURBO 3 Press the b2. Clean the electric components with jets of air 2 Verify that all the electric components are firmly tightened 2 Clean the fan 2 Verify that all the fan assembly is firmly tightened 2 Clean the condensate drain pan 2 3 amp The checks and maintenance operations described are essential to guarantee the efficiency of the air conditioner The frequency of these operations varies according to the characteristics of the area the amount of dust etc 1 The described operations should be performed more frequently if the area of installation is very dusty 2 These operations must always be performed by qualified personnel For more detailed information see the Installation Manual ENGLISH Protections enabled by the Unit control system Type of protection Description Operation When it enables Heating on Protection against cold air The internal fan is off heat pump During operation Heating on Defrost cycle The internal fan is off heat pump During operation Anti frost protection of internal battery Cooling During The compressor is off operation At start up or during the selection of the operating mode The start of the Cooling or heating compressor is delayed on heat pump Delayed start of compressor If the air conditioner is operating in heat pump mode it performs several defrost cycles in order to remove the frost that may have depo
3. ceeee cece eee eeee eee 16 m Selecting the Energy Saving Function 0eeeeee 17 m Adjusting the Airflow Direction Vertically 18 m Adjusting the Airflow Direction Horizontally 19 m Setting the On Timer ec cccccee cece cece teen kakasa 20 m Setting the Off Timer enserio cece ee A 21 m Setting the Sleep Timer cc cece cece eee e ee eeeeeeeeee 22 m Setting the 1 Hour Timer cece eee ee eee eee eeeeeee 23 RECOMMENDATIONS FOR USE m Operating Recommendations cee cece ee eeeeeeee 24 m Temperature and Humidity Ranges asawa 25 m Operating Your Air Conditioner Without the Remote Control 25 m Troubleshooting Guide cee cece cece eee eee eee ika 26 m Cleaning Your Air Conditioner cea 27 m Cleaning Deodorizing and Bio Filter Option 28 m Periodical Checks u u een 29 m Protections enabled by the Unit control system 30 ENGLISH Name of Each Part The design and shape can be changed according to the model 4 Temperature sensor Power On Off button Air filter Airflow blades Air Inlet under the grille outlet Timer indicator F
4. You can set the temperature between 61 F 16 C and 86 F 30 C Result Each time you press the Y Ad button The temperature is adjusted by 1 F The indoor unit beeps If the room temperature is higher than the selected temperature the air conditioner starts cooling If the room temperature reaches the set temperature the air conditioner stops cooling but the fan operates consistently FAN SPEED 4 Press the button to select the fan speed until the required settingis displayed SP al Automatic rotated gt Siu gt Saat oR Low Raat Medium Rail High h aall Maximum FAN SPEED Result Each time you press the O button the indoor unit beeps The fan speed indicator increases and decreases continuously and turns round each time you press the FAN SPEED button 5 Tocontrol the airflow direction refer to pages 16 and 17 Selecting the Heat Mode ENGLISH You can select the Heat mode if you want to heat your room You can adjust the temperature and the fan speed when heating 1 Ifnecessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last The indoor unit beeps MODE 2 Press the button on the remote control until dis displayed MODE Result Theindoor unit beeps each time you press the button The air conditioner runs in the Heat mode You can change modes at any t
5. mode frost may form in the outdoor unit due to the low temperature and high humidity If this happens The heating operation is stopped The air conditioner defrosts automatically for about 7 minutes After about 7 minutes the air conditioner starts operating again normally High indoor and outdoor temperatures If both the indoor and outdoor temperatures are high when you select the Heat mode the fan and the compressor of the outdoor unit may stop at times This is normal wait until the air conditioner turns on again Power failure If power failure occurs when the air conditioner is operating the air conditioner turns off When the power returns the air conditioner starts up again automatically Protection mechanism When the air conditioner is started immediately after being plugged in or stopped the normal operation starts up after 3 minutes for the reason of protection Temperature and Humidity Ranges ENGLISH If you check the following tables you can use your air conditioner more efficiently If the air conditioner is used at Then Heating capacity The air conditioner may stop operating for the reason of protection Low temperatures Water may leak and some malfunction may occur if the heat exchanger freezes High humidity levels Water may condense and drip from the surface of the indoor unit if you don t use the air conditioner for a long time Operation Ou
6. HSITDN4 Register your product at www samsung com global register Safety Precautions You should take the following safety precautions when using your air conditioner A WARNING e If you don t follow the safety precautions you may get the risk of an electric shock injury or death e The manufacturer or qualified service personnel must install this air conditioner e Unplug the electric power before repairing installing or cleaning DURING OPERATION Do not repair the air conditioner at your discretion re It is recommended to contact a service center directly Never spill any kind of liquid on the air conditioner If this happens unplug or turn off the air conditioner and contact an authorized service center Do not insert anything between the airflow blades to prevent damage of the inner fan and consequent injury Keep children away from the air conditioner Do not place any obstacles in front of the air conditioner Do not spray any kind of liquid into the indoor unit If this happens turn off the breaker and contact a service center Make sure that the air conditioner is well ventilated at all times Do not place a cloth or other materials over it Remove the batteries if you don t use the remote control for a long time If applicable Use the remote control within 23ft 7m from the indoor unit If applicable DISPOSING OF THE UNIT Before throwing out the air conditioner remove the batteries f
7. UTH AFRICA 0860 SAMSUNG 726 7864 www samsung com U A E 800 SAMSUNG 726 7864 8000 4726 Samsung Electronics Co Ltd All Rights Reserved www samsung com EP USER S MANUAL AQV36J ENGLISH ESPA OL FRAN AIS Split type Air Conditioner Cooling and Heating INVERTER TER TE gt DOP DB98 29386A 1 CW GH KP
8. an mode indicator E eiad Power On Off button Energy saving indicator Remote Control Sensor Operation indicator Cool Heat mode ENGLISH AQV36J Air Inlet Rear Air Outlet Connection Valve Remote Control Buttons and Display Transmission indicator Temperature and Timer setting 1 Hour Timer indi our Timer indicator Battery life indicator On Timer indicator Off Timer indicator Operation modes indicator AUTO S amp COOL DRY ofp FAN OF HEAT Turbo function indicator Airflow direction Sleep mode indicator Fan speed amp Silence indicator Energy saving indicator Turbo button Power On Off button 1 Hour Timer button Mode selection button AUTO COOL DRY FAN HEAT Temperature adjustment button Fan speed adjustment button amp Silence mode button Energy Saving button Airflow control button Good Sleep button On Timer button Timer Set Cancel button Battery check button Off Timer button Note Each mode indicator shows the current setting and the battery life You can check the battery life by pressing the a button The number of the battery life indicator means the remaining battery life Replace the batteries when only one battery life indicator remains Inserting the Remote Control Batteries ENGLISH You must insert or replace the remote control batteries when You purchase the air conditioner The remote control does not work corr
9. ase the fan speed If the airflow is directed upwards set the blade downwards with the remote control The fan speed does not change when you press the ry button Check if the mode is set to the Auto Cool Heat or Fan mode in the Dry mode the fan speed changes automatically The airflow direction does not change when you press the FLAP button O Check if the air conditioner has been turned on if necessary press the On Off button on the remote control The timer is not correctly triggered Check if the timer is set correctly see pages 18 and 19 Odor permeates into the room during operation You can use the Fan mode to ventilate your room Cleaning Your Air Conditioner For the best use of your air conditioner you must clean it every 2 weeks to remove the dust that accumulates on the air filter PORTANT Before cleaning your air conditioner check if you have turned off the circuit breaker 1 Open the upper front grille by pulling the lower right and left tabs of the grille ENGLISH 2 Pullair filters out of each tab of the grille 3 Remove all dust on the air filters with a vacuum cleaner or brush 4 When you finish insert air filters by fixing them to each tab of the grille 5 Toclose the front grille fix it to hooks and push down the lower right and left tabs of the grille A
10. e operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last The indoor unit beeps Result MODE 2 Press the button on the remote control until 4is displayed The indoor unit beeps each time you press the O button The air conditioner runs in the Dry mode Result You can change modes at any time 3 Press the Y A button to adjust the temperature until the required temperature is displayed You can set the temperature between 61 F 16 C and 86 F 30 C Each time you press the 7 A button The temperature is adjusted by 1 F The indoor unit beeps The air conditioner starts dehumidifying and the fan speed is adjusted automatically Result 4 Tocontrol the airflow direction refer to pages 16 and 17 Selecting the Fan Mode ENGLISH You can select the Fan mode if you want to ventilate your room It helps to refresh the air in your room You can adjust the fan speed in this mode 1 Ifnecessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last The indoor unit beeps MODE 2 Press the O button on the remote control until amp dis displayed Result The indoor unit beeps each time you press the O button Theair conditioner runs in the Fan mode The temperature is set automatically You can change modes at any t
11. e quick and convenient way using only one button IHR D 2 ee ad 1 Press the button until the EIS indicator appears on the remote control MODE 2 Press the button until the desired mode is displayed at the remote control to select the mode after setting the 1 Hour Timer Result The air conditioner operates in the selected mode for an hour If you set the 1 Hour Timer when the air conditioner is turned off the air conditioner turns on and operates for an hour To cancel the 1 Hour Timer 1HR 1 Press the button to cancel the 1 Hour Timer Result The indoor unit beeps The indicator is no longer displayed Theair conditioner operates normally ip SET TEMP ae CO ms Cr fh Alfa asd Qi ai THR TEMP ENGLISH Operating Recommendations When you use your air conditioner it is recommended to read the following Topic Recommendation Heating capacity The heat pump inside the air conditioner absorbs heat from outside air and brings it indoors If the temperature of the outside air drops the air conditioner heats less If the room is not warm enough use an additional heating appliance Warm air circulation The air conditioner circulates warm air to heat your room It will take some time to warm the air in your room entirely after the air conditioner turns on Therefore turn the air conditioner on in advance Frost When you select the Heat
12. ectly Use two AAA LR03 1 5V batteries Do not use old batteries or different kinds of batteries together Batteries may be completely discharged after 12 months even if they have not actually been used 1 Remove the battery cover in the rear of the remote control by pushing it with your thumb 2 Insert two batteries respecting the polarities as indicated by the and symbols 3 Close the cover by sliding it back in its place Getting Start The User s Manual provides you with valuable information about your air conditioner Please read this manual carefully before using the air conditioner It will help you take full advantage of the unit s features You have already seen the basic description of the unit on pages from 4 to 6 Starting up with the next page you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use three different symbols PRESS PUSH HOLD DOWN Selecting the Auto Mode ENGLISH You can select the Auto mode if you want to cool or heat your room automatically You can adjust the temperature in this mode 1 If necessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last The indoor unit beeps MODE 2 Press the button on the remote control until 4w dis displayed Result The ind
13. ime FAN SPEED 3 Press the O button to select the fan speed until the required setting TEMP IR is displayed A Low 4 4 Ru Medium Al pa So saat High yy FAN SPEED FAN SPEED GY SAVING Result Each time you press the O button the indoor unit beeps CA O FLAP SLEEP 4 Tocontrol the airflow direction refer to pages 16 and 17 Selecting Good Sleep Mode Good Sleep mode helps users to fall asleep well after going to bed whether being too hot to sleep or being awakened by coldness The Good Sleep mode can be selected only when the air conditioner is switched on in cool heat mode 1 If necessary press the in button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last The indoor unit beeps Mode Fan Speed O Modi ng 2 Press the button to select 4 or O 4 mode Result The indoor unit beeps each time you press the 4 button The air conditioner runs in cool or heat mode 3 Press the YY button until the D indicator appears on the remote control Inthe case of adjusting time Press the button to adjust desired operation time from 1 to 12 hours Good Sleep mode will automatically stop after the set time Set Cancel Press the O button Result In the case of adjusting the extra time for Good Sleep mode you Set Cancel should pre
14. ime SET TEMP by Tag F BT 3 Press the Y A button to adjust the temperature until the required temperature is displayed You can set the temperature between 61 F 16 C and 86 F 30 C Result Each time you press the Y A button E Tga The temperature is adjusted by 1 F The indoor unit beeps If the room temperature reaches 9 F higher than the set temperature the air conditioner stops heating but the fan operates consistently If the room temperature reaches 5 F lower than the set temperature the air conditioner starts heating again FAN SPEED 4 Press the button to select the fan speed until the required settingis displayed P s Automatic rotated gt Rn gt Rent Kh Low oR aa Medium Kiat High Ka a all Maximum FAN SPEED ENERGY SAVING FAN SPEED Result Each time you press the button the indoor unit beeps For the first 3 5 minutes the fan may not operate to prevent the cool air from running out of the indoor unit It helps to warm the air in your room sufficiently FAN SPI FLAP 5 To control the airflow direction refer to pages 16 and 17 Selecting the Dry Mode SET TEMP by ng F NA But FAN SPEED ENERGY SAVING TURBO POWER 1HR Gi You can select the Dry mode if you want to dehumidify your room You can adjust the temperature in this mode 1 Ifnecessary press the On Off button Th
15. ir filter Body groove Front grille 6 Clean the front grille with a damp cloth and mild detergent do NOT use benzene solvents or other chemicals If you have not used the air conditioner for a long time select the Fan mode for 3 to 4 hours to dry the inside of the air conditioner C 5 Front grille Hook ka Body Cleaning Deodorizing and Bio Filter Option There are Deodorizing and Bio filters inside your air conditioner They remove odors and dust in your room You should clean the filters every 3 months 1 Open the upper front grille by pulling the lower right and left tabs of the grille 2 Pullout the deodorizing and Bio filter Bio Filter Deodorizing Filter 3 Wash the filters with clean water then dry them in the shade 4 Insert the filters in their place You can change the position of filters with each other 5 Close the front grille Periodical Checks Description Monthly Every 4 months Once a year Indoor unit Clean the air filter 1 Clean the condensate drain pan 2 Thoroughly clean the heat exchanger 2 Clean the condensate drain pipe 2 Replace the remote control batteries Outdoor unit Clean the heat exchanger on the outside of the unit 2 Clean the heat exchanger on the inside of the unit 2
16. l Problem Explanation Solution The air conditioner does not operate Check if the circuit breaker of the air conditioner is switched on Check if the air conditioner is turned on If necessary press the 39 On Off button on the remote control Check if the Timer indicator on the indoor unit is on If so Wait until the set time is reached and the air conditioner starts automatically Cancel the Timer See pages 18 and 19 for further details The air conditioner does not operate with the remote control Check if there are no obstacles in front of the indoor unit Check the remote control batteries Make sure that you are with in 7 meters from the indoor unit No beep is heard when you press the On Off button on the remote control Check if you are pointing the remote control at the remote control sensor on the right side of the indoor unit Replace the remote control batteries if necessary The air conditioner does not cool or heat Check if the correct operating mode has been selected Auto Cool Heat The room temperature may be too low or too high Check if the air filter is dirty refer to page 25 for cleaning instructions Check that there is no obstacle in front of the outdoor unit When heating the required room temperature is never reached and the air conditioner frequently stops Check if the required temperature is set correctly Incre
17. lly The outer airflow blade moves up and down to increase the efficiency of the cooling or heating operation FLAP 1 Press the button until the required direction is set Result The outer blade is adjusted vertically FLAP 2 Press the button to move the blade up and down automatically during operation FLAP 3 Press the O button again to stop the blade moving up and down If you turn the air conditioner Then the blade Off is closed completely On set to the default position Adjusting the Airflow Direction Horizontally ENGLISH You can adjust the airflow direction horizontally with your hands The inner blades with small fins moves the air to the required direction 1 Adjust the inner blades by moving them to left or right Setting the On Timer You can set the On Timer to turn on the air conditioner automatically at the appointed time You can set the time from 1 hour to 24 hours 1 Pressthe button until the required time is displayed to set the On Timer You can set the time between 1 hour and 24 hours SET CANCEL 2 Pressthe button to complete the setting Result The remaining time is displayed The timer indicator stops blinking The selected mode and the temperature on the display disappear after 10 seconds The air conditioner tur
18. ns on automatically at the appointed time and the On Timer setting disappears MODE 3 Press the button until the desired mode is displayed at the top of theremote control to select the mode in advance Result The air conditioner operates in the selected mode when it is turned on If you don t use the remote control after setting the On Timer it turns off automatically after 25 hours To Cancel the On Timer SETICANCEL 1 Press the O button to cancel the On Timer SET CANCEL Ifyou press the button both the On Timer and the Off Timer are canceled Setting the Off Timer ENGLISH You can set the Off Timer to turn off the air conditioner automatically at the appointed time You can set the time from 1 hour to 24 hours 1 Pressthe button until the required time is displayed to set the Off Timer You can set the time between 1 hour and 24 hours BATTERY button to complete the setting SET CANCEL 2 Press the O Result The remaining time is displayed The timer indicator stops blinking Theair conditioner turns off automatically at the appointed time and the Off Timer setting disappears If you would like to turn the air conditioner on after 2 hours and to operate it for 2 hours 1 Press the button until 2 0 Hr is displayed SETICANCEL 2 Pressthe button 3 Press the 7 button until 4 0 Hr is displayed 4 Press the button Y
19. oor unit beeps each time you press the O button The air conditioner runs in the Auto mode The Auto mode cools or heats the room depending on the set temperature The air conditioner changes the Cool or Heat mode automatically depending on the current temperature during operation You can change modes at any time 3 Press the Y A button to adjust the temperature until the required temperature is displayed You can set the temperature between 61 F 16 C and 86 F 30 C Result Each time you press the X7 A button The temperature is adjusted by 1 F The indoor unit beeps FAN SPEED ENERGY SAVING Selecting the Cool Mode EN TEMP FANSPEED ENERGY SAVING SET TEMP FRK FAN ap SAVING Q SLEEP FLAP You can select the Cool mode if you want to cool your room You can adjust the temperature and the fan speed when cooling 1 Ifnecessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last The indoor unit beeps MODE 2 Press the button on the remote control until qis displayed MODE Result The indoor unit beeps each time you press the O button The air conditioner runs in the Cool mode You can change modes at any time 3 Press the Y button to adjust the temperature until the required temperature is displayed
20. ou can check or change the mode and or the temperature by pressing the button or the 17 A button after setting the Off Timer To Cancel the Off Timer SETICANCEL 1 Press the button to cancel the Off Timer SET CANCEL Ifyou press the button both the On Timer and the Off Timer are canceled Setting the Sleep Timer You can set the Sleep Timer to turn off the air conditioner automatically while you are sleeping The air conditioner stops operating 6 hours after you set the Sleep Timer SLEEP r Br 1 Press the button until the 2 indicator appears on the remote control Pini Result The indoor unit beeps al The air conditioner will be controlled as indicated in the gt illustrations below KET You can set Sleep Timer only in the Cool or Heat mode Cooling The set temperature is increased by 1 C every hour After the increase of 2 C the temperature is maintained for 4 hours Heating The set temperature is decreased by 1 C every hour Start Stop After the decrease of 2 C time time the temperature is maintained for 4 hours To Cancel the Sleep Timer SLEEP 1 Press the button to cancel the Sleep Timer Result The indoor unit beeps The D indicator is no longer displayed The air conditioner operates normally Setting the 1 Hour Timer You can set the 1 Hour Timer to turn off the air conditioner automatically after an hour It is th
21. rom the remote control When you dispose of the air conditioner consult your dealer If pipes are removed incorrectly refrigerant may blow out and cause air pollution When it contacts with your skin it can cause skin injury The package of the air conditioner should be recycled or disposed properly for environmental reasons OTHERS Never store or load the air conditioner upside down or sideways to prevent the damage of the compressor Young children or infirm persons should be always supervised when they use the air conditioner Max current is measured according to IEC standard for safety Current is measured according to ISO standard for energy efficiency Contents PREPARATION m Safety Precautions 0 ec ccceeeee cece cece eee eeeeeeeeeeee 2 m Nameiof Each Part nase duane 4 m Remote Control Buttons and Display asawa 6 m Inserting the Remote Control Batteries 7 m Getting Started cece cece reece kaawaan 8 OPERATION m Selecting the Auto Mode cccccceeeeee00ussnaana 9 m Selecting the Cool Mode ccccceeeeeeuvan nanana 10 m Selecting the Heat Mode ccccceceeeusus saaan 11 m Selecting the Dry Mode cceeeceeeee0000s0 anang 12 m Selecting the Fan Mode cceecceeeee00000 naaawa 13 m Selecting Good Sleep Mode cccsseaaaa aasa 14 m Selecting the Turbo Function
22. sited on the outdoor unit at low temperatures In this case the internal fan is switched off automatically and restarted only after the defrost cycle is completed Contact SAMSUNG WORLD WIDE If you have any comments or questions regarding a Samsung product contact the SAMSUNG customer care center Country Customer Care Center ELECTRONICS Web Site CANADA 1 800 SAMSUNG 726 7864 www samsung com ca MEXICO 01 800 SAMSUNG 726 7864 www samsung com U S A 1 800 SAMSUNG 726 7864 www samsung com ARGENTINE 0800 333 3733 www samsung com ar BRAZIL 0800 124 4214004 0000 www samsung com CHILE 800 SAMSUNG 726 7864 www samsung com cl Nicaragua 00 1800 5077267 Honduras 800 7919267 COSTA RICA 0 800 507 7267 www samsung com latin ECUADOR 1 800 10 7267 www samsung com latin EL SALVADOR 800 6225 www samsung com latin GUATEMALA 1 800 299 0013 www samsung com latin JAMAICA 1 800 234 7267 www samsung com latin PANAMA 800 7267 www samsung com latin PUERTO RICO 1 800 682 3180 www samsung com latin REP DOMINICA 1 800 751 2676 www samsung com latin TRINIDAD amp TOBAGO 1 800 SAMSUNG 726 7864 www samsung com latin VENEZUELA 0 800 100 5303 www samsung com latin COLOMBIA 01 8000112112 www samsung com co Turkey 44477 11 www samsung com SO
23. ss the O button within 10 seconds If you do not press the AY button within 10 seconds Good Sleep mode will automatically stop in 8 hour operation 4 Press the Q button to adjust the temperature until the required temperature is displayed You can set the temperature between 61 F 16 C and 86 F 30 C Result Each time you press the X A button The temperature is adjusted by 1 F The indoor unit beeps Aa ENGLISH Temperature changes in good sleep mode To prevent excessive cooling heating during sleep the good sleep mode automatically modifies the temperature setting in accordance with the time setting Temperature and air current change according to the three stages Falling asleep Sound sleep and Waking up from good sleep mode and then the air conditioner will automatically turn off when the set time has elapsed Three stage good sleep prevents you from having difficulty sleeping on extremely hot cold nights Falling asleep Eases you into sleep by dropping the temperature Sound sleep Relaxes your body and raises your temperature slightly Waking up from good sleep mode Allows you to wake up to comfortable crisp air making you feel refreshed and energized Set the Off timer in good sleep mode for more than 5 hours Sleep may be disturbed if the good sleep mode is set for too short or too long a time because the temperature changes are set to an 8 hour cycle
24. tdoor Temperature Indoor Temperature Indoor Humidity Heating 5 F to 75 F approx 80 F or less 15 C to 24 C approx 27 C or less Cooling 14 F to 109 F approx 61 F to 90 F approx 80 or less 10 C to 43 C approx 16 C to 32 C approx Dehumidifying 14 F to 109 F approx 61 F to 90 F approx 10 C to 43 C approx 16 C to 32 C approx 3k If the outdoor temperature is as low as 32 F 0 C the heating capacity drops up to 70 80 depending on the operating condition If you use the air conditioner over 90 F 32 C indoor temperature the cooling capacity may drop Operating Your Air Conditioner Without the Remote Control You can operate your air conditioner directly without the remote control 1 Toturn the air conditioner on press the On Off button on the right side of the indoor unit Result The Operation indicator on the indoor unit lights up The indoor unit beeps The air conditioner starts up in the appropriate mode for the room temperature The air conditioner changes the Cool or Heat mode automatically depending on the current temperature during operation 2 Toturn the air conditioner off press the On Off button again Even if you turned the air conditioner on with the On Off button you can control it with the remote control Troubleshooting Guide Before contacting the service center check the following It will save your time and theexpense of an unnecessary cal
25. utton again to stop the Turbo Function before the end ofthe 30 minute period Result The air conditioner is reset automatically to the previous setting TURBO POWER 4 To control the airflow direction refer to pages 16 and 17 Selecting the Energy Saving Function ENGLISH You can select the Energy Saving Function to save energy when cooling or heating 1 Ifnecessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode you selected last The indoor unit beeps ENERGY SAVING 2 Press the O button Result Theindoor unit beeps The air conditioner runs in the Energy saving mode The outer airflow blade moves up and down To stop the Energy saving mode press the O again ip SET TEMP el Dl You can select the Energy saving mode only in the Cool and Heat tal mode TURBO POWER THR of 3 Press the Y A button to adjust the temperature until the required temperature is displayed FAN SPEED ENERGY Sk FLAP SLEEP a FAN SPEED 4 Press the button to select the fan speed until the required setting is displayed 5 To control the airflow direction refer to pages 16 and 17 FAN SPEED ENERGY SAVING NG G Fo RX ac a a NOS at v FAN ig SAVING FLAP SLEEP Gaan pe Adjusting the Airflow Direction Vertically You can adjust the airflow direction vertica
Download Pdf Manuals
Related Search