Samsung VC-7727V User Manual
Contents
1. DJ68 40149A 2001 11 269 50AM 1 Operating Instructions Before operating this unit please read the instructions carefully DJ68 40149A 2001 11 269 50AM 2 p IMPOR TANT SAFE GUA RDS This appliance must be connected to the same voltage of electrical power supply as shown on your vacuum Cleaner s rating plate 2 gt Do not use your vacuum cleaner on a wet surface It cannot be used to remove liquids gt gt Carpets treated with a liquid cleaner must be allowed to dry before being cleaned with the unit gt Never operate the vacuum cleaner without a dust bag gt If a dust bag is not inserted the cover cannot be closed please do not close forcibly 3 gt Keep children away from your vacuum cleaner It must not be used on people or animals 3 gt Never use your vacuum cleaner to vacuum matches glowing embers or cigarette ends Avoid vacuuming hard pointed objects since they may damage the appliance or dust bag 3 gt Consult the trouble shooting guide in this manual if your vacuum cleaner fails to operate properly Contact an authorized service agent if the problem persists gt if the main cable is defective the complete cable winder must be replaced by a service P agent 2 gt Don t use your vacuum cleaner outdoors gt When you have unpacked the unit do not simply throw the packing into the household wasie 3 gt Take them to an appropriate collecting point f2. d dust bag can be sealed by removing the film from the paper and sticking the latter over the Ss wane suction opening ONLY PAPERBAG A FOR CLOTH FILTER BAG After using if the cloth filter bag is full of dust clean the cloth filter bag and use it again _ 1 MAINTENANCE OR REPLACEMENT OF THE FILTERS 1 INLET FILTER x Open the dust cover GRILLEFILTER x After detaching the filter wash it lightly with l water dry it in the shade and then insert it in its original position Close the dust cover 2 OUTLET FILTER The outlet filter which the air comes out from the vacuum cleaner x Open the dust cover and then pull the hook upward The hook is located at the front of the dust cover Remove and replace the exhausted outlet filter x Close the grille filter and then close the dust cover o P DJ68 40149A 2001 11 269 50AM 8 p RUG FLOOR SELECTOR Before use make sure that the position of the selector button is in the right position for the type of surface to be cleaned In order to maintain best cleaning efficiency clean floor brush using crevice tool after use Push to side when cleaning the carpets Push to side when cleaning the floor tile mat etc TROUBLE SHOOTING Motor does not start g No power supply Check cable plug and socket a Suction force is gradually Filter nozzle suction hose Ea Remove the object decreasing or
3. ion 2 Connect the suction tubes together tube lt depending on model ION Adjusting the telescopic tube depending on model 3 Gonnect the nozzle to the suction tube 4 Connect the connector to the body ofthe cleaner POWER CORD 1 PULLING OUT The long power cord can be drawn out for your convenience 2 REWINDING After disconnecting the plug from the electrical outlet press the cord rewind button lightly with your toe The cord will rewind ON OFF SWITCH You can start or stop your vacuum cleaner by pressing the on off switch lightly with your toe DJ68 40149A 2001 11 269 50AM 5 p USING THE BLOWER EXCEPT HANDLE CONTROL TYPE To blow out dust in crevice or corners you can use this function for your convenience Located on the rear side of the cleaner 1 Disconnect the hose clamper from the 2 Open the tool storage cover body of the cleaner 3 Remove the blow hole cap from the 4 Connect the hose clamper to the blow body of the cleaner hole fam FE Don t use your vacuum cleaner outdoors USING THE MITE KILLER OPTIONAL 1 Disconnect the body connector from the body of the cleaner 2 Shut the hose connection cover until tone is heard e Your vacuum cleaner is not malfuctioning if it starts to operate when the hose connection cover is closed This will happen if the HOSE CONNECTION COVER vacuum cleaner was on when the ho
4. or the recycling DJ68 40149A 2001 11 269 50AM 3 p HANDLE POWER CONTROL ONLY HANDLE CONTROL TYPE HANDLE UCTION HOSE TUBE BUTTON FOR SUCTION HOSE REMOVAL FOR BLOWING DUST FULL INDICATOR ORD REWIND BUTTON POWER CONTROL SWITCH ITE KILLER LAMP ON OFF SWITCH FLOOR NOZZLE BUTTON FOR SUCTION HOSE REMOVAL FOR USING THE MITE KILLER p gt Features marked may vary according to model HANDLE CONTROL OPERATION ONLY HANDLE CONTROL TYPE The suction capacity can be regulated steplessly by moving the side A to the desired position SLIDE IN THE STOP POSITION Vacuum cleaner switches off stand by mode SLIDE TOWARDS MAX Suction capacity increases steplessly up to max POWER CONTROL ONLY SLIDING REGULATOR TYPE Vacuuming power can be adjusted to suit different situations using the power control rate ca MIN For delicate fabrics like curtains MAX For hard floors and heavily soiled carpets P DJ68 40149A 2001 11 269 50AM 4 p DUST FULL INDICATOR lf the Dust Full indicator switches to RED while you are cleaning the dust bag requires replacement EMOTE If the Dust Full indicator continues to display RED even after changing the dust bag turn the cleaner off to see if the hose tube or nozzle is clogged ASSEMBLING THE VACUUM CLEANER READY FOR USE 1 Connect the suction hose to the suct
5. se was E removed 3 Mite killer lamp on Insect and germ killing work is started It will continue for 2 to 5min and the process stops automatically MITE KILLER LAMP O P DJ68 40149A 2001 11 269 50AM 6 p TE If you want to stop the machine while operating you can either open hose connection cover press On Off button or unplug the plug USING THE ACCESSORIES Press the tool storage cover downward x Crevice tool for radiators crevice comers between cushions x Upholstery brush for cushions and drapery Dusting brush for furniture shelves books etc Before use assemble the orl brush to the crevice 00 PARK POSITION Located in the top rear side of the vacuum cleaner there is a nozzle support that can be used to park the nozzle during pauses in cleaning For easy storage and transportation this vacuum cleaner has a clip system built into the body which will keep the tube hose and nozzle in a vertical position Oo Q DJ68 40149A 2001 11 269 50AM 7 p REPLACING THE DUST BAG 1 To open the dust cover of the dust bag 2 Remove the carrying bag from the compartment press the clamper upward cleaner The clamper is located at the front of the dust cover 3 After removing the used dust bag 4 Press the dust cover down gently until insert the cardboard bag collar of the the clamper relocks new dust bag into the carrying bag OTE Use
6. tube is blocked Check that the cordis not Pull the cord out 2 3m amp push twisted or wound unevenly down the cord rewind button Cord does not rewind fully This Vacuum cleaner is approved the following EMC Directive 89 336 EEC 92 31 EEC and 93 68 EEC Low Voltage Safety Directive 73 23 EEC and 93 68 EEC DJ68 40149A REV 0 8
Download Pdf Manuals
Related Search