Samsung WA7584C1 manual de utilizador
Contents
1. install it in the area with moisture or outdoor where it has rain or snow e An electric shock or a fire may take place Please unplug the power supply cord when you do not use it e An electric shock or a fire may take place If there is dust or water on the power supply plug and its connected part please remove it completely e An electric shock or a fire may take place Do not make your kids look into the inside of the washer e If your kid falls into the washer his life could be in danger Ventilate immediately without touching the power plug if gas is leaking e An electric shock or a fire may take place if it catches flame If the washer makes strange noise smell or smoke unplug it promptly and call service agent e An electric shock or a fire may take place When cleaning don t spray water to the parts of the washer directly e It may make it s life span shorten Also an electric shock or fire may take place Don t use several appliances together with an outlet e A fire may take place due to unusual heat Don t press the button with an awl or pin e An electric shock or a fire may take place Option ing with the washer How to start the Child Lock function Child Lock function This is a device to protect children from being accidentally hurt while play Press the Power button to go to an initial washing mode By pressing Start Hold button you start washing and in case Child Lock2. A3SN MI SLA Vd JO NOIdIN SIA CONTROL PANEL For more details see control panel of your washing machine gt POWER BUTTON POWER Press this button once to operate Press once again to turn the power off gt START HOLD BUTTON HOLD Use to pause and restart the operation To change the washing procedure during operation press this button to stop and once again to restart after changing the procedure gt DELAY START BUTTON a Press this button when delay start washing is needed cou gt COURSE SELECT BUTTON 4 With every press of this button the washing course changes FUZZY gt BLANKET SPEEDY gt WOOL gt FUZZY FUNCTION gt FUNCTION SELECT BUTTON i With every press of this button the function changes SOAK WASH RI NSE SPI N gt WASH gt RINSE gt SPIN gt WASH amp RINSE gt RINSE amp SPIN WASH RINSE SPIN gt WATER LEVEL SELECT BUTTON WATER According to the washload select the water level LEVEY MEDIUM gt HIGH gt EXTRA LOW gt LOW Option WATER gt WATER SUPPLY SELECT BUTTON w As you press this button the type of water is selected as follows COLD gt COLD HOT gt HOT gt COLD gt REMAINING TIME INDICATOR LIGHT The indicator light shows the remaining time in minutes of each wash cycle At the end of the cycle the power automatically switches off WASHING PROCEDURE Before starting washing check the following Connect the water supply hose to the w
3. SELECT button once Press the START HOLD button once Water level is selected automatically Washing rinsing and spinning follow POWER FINGTION gt wo WASH ONLY Press the POWER button Press the FUNCTION SELECT button twice Press the START HOLD button once When the FUNCTION button is pressed during washing the wash time can be changed to between 3 and 25 minutes in duration RINSE ONLY Press the FUNCTION button three times N START Press the START HOLD button once POW wo HOLD When the FUNCTION button is pressed during rinsing the rinse three times times can be changed to between 1 to 5 times in duration SPIN ONLY T Press the FUNCTION button four times POW ue HOLD Press the START HOLD button once four When the FUNCTION button is pressed during spinning our imes the spin time can be changed to from 1 to 7 minutes WASH AND RINSE Press the FUNCTION button five times POWER rucno gt Ho Press the START HOLD button once a When the FUNCTION button is pressed during working the rinse five imes times can be changed to between 1 to 5 times in duration RINSE AND SPIN Press the FUNCTION button six times START Press the START HOLD button once POWER gt FUNCTIOJ 4 4 Hoy Rinsing and spin drying follow six times When the FUNCTION button is pressed during working the rinse times can be changed to between 1 and 5 times in duration INSTALLATION amp MAINTENANCE The User s Manual is
4. CIFICATIONS HIGH 751 CONSU E MEDIUM CONSUMPTION 55 SPIN LOW STANDARD LOW ies WATER LEVEL DIMENSIONS mm W588xD618xH955 EXTRA LOW ae WEIGHT 38 kg WATER USAGE 202 0 05 0 78 MPa PULSATOR i WATER PRESSURE 0 5 8 0 kg f cm ROTATING SPEED 00 rpm WASHING TYPE Stirring Type SPIN SPEED 680 rpm
5. WASHING MACHINE User s Manual FEATURES cc ciiscsccsscvsecsescsvsscvsssaasstcencavsaccdisisesieuscenas SAFETY INSTRUCTIONS DESCRIPTION OF PARTS o ae CONTROL PANEL 00 ceeccceceeeeeeeeeeeeeeeeeeeees WASHING PROCEDURE FUZZY course sssrin Blanket course Speedy course Wool course Delay Start COUVSO miressa ntan MANUAL FUNCTIONS o ae INSTALLATION amp MAINTENANCE Environment cienvsuereeveaiavanst Geet EE E E E E E E danstveends Connecting the water supply hose seess Assembling the rat protection panel In case of pump drained washer Connecting the drain hose How to add the fabric softener How to put the detergent in Water supply connector filter cee eeeeeeeeeeee Cleaning the filter net 00 eee eceeeeeseeeeeeeeeeeeeeeee Please read this manual before using and note how to use in the proper manner How to cloanthe filter Please be careful of keeping the manual Warning in moving washing machine Otherwise it should be bought separately TROUBLESHOOTING SPECIFICATIONS The User s Manual is for common use Make use of the User s Manual depending upon your washing machine model CODE NO DC68 01518X FEATURES FUZZY CONTROL e Fuzzy control operates with best washing course by sensing the washload like artificial intelligence TRANSPARENT WINDOW gt P ion e This Transparent Window is the new concept to solve the c
6. ater tap Leave a tap open Plug the power cord in Make sure to lay down the drain hose In case no drain pump Put the laundry into the washer and add detergent too Be careful not to overload Use right detergent for the fabrics you are washing gt FUZZY COURSE em N Selects the best washing course Pow gt HO automatically 1 Press the POWER Button to ON 2 Press the START HOLD button Water level is selected automatically Washing rinsing and spinning follow If you want to pause press the START HOLD button again You can change the course when paused 3 Close the lid gt BLANKET COURSE ome gt o gt ai 1 Press the power button to ON 2 Press the course select button once 3 Press the START HOLD button Water level is selected automatically Washing rinsing and spinning follow If you want to pause press the START HOLD button again You can change the course when paused 4 Close the lid gt SPEEDY COURSE START u gt canes gt ag Because washing is speedy it is good for light or less stained laundry 1 Press the power button to ON 2 Press the course select button twice 3 Press the START HOLD button Water level is selected automatically Washing rinsing and spinning follow If you want to pause press the START HOLD button again You can change the course when paused 4 Close the lid gt WOOL COURSE START rons gt comes gt a 1 Press the power button
7. ction panel to the assembling hole on back side to the end 2 lf you have difficulty inserting the panel lift up the washer a little and insert it gt IN CASE OF PUMP DRAINED WASHER P Take out the cap hose and Be sure to join tightly the drain hose into Be sure to join tightly the drain Install the drain hose in the connect the outlet hose the drain outlet on the back of the hose into the drain outlet position of about 90 100cm machine on the side of the machine above the ground e De FS D Nas cap hose o Oil Eg outlet hose gt CONNECTING THE DRAIN HOSE on a After pressing the joint ring a insert the drain hose b to drain direction b gt HOW TO ADD THE FABRIC SOFTENER 0 e When a proper amount one time does of fabric e Do not open the lid during the Spin Dry cycle softener is stored in the softener inlet it is If added too early its effectiveness will decrease automatically put in at the last rinsing cycle Do not leave the softener e Do not use detergent bleach or starch into into the Softener the Softener Inlet Dispenser for a long time e Using too much softener may produce Because softner s unsatisfactory results became stiff gt HOW TO PUT THE DETERGENT IN 7 1 Open the detergent box by pulling in the direction of the arrow as shown in the figure and then put the powder detergent in the detergent box 2 Put in one time amount
8. e filter clockwise OPEN CLOSE remove dirts FILTER until it locks in position S 4 Reassemble in CRAG reverse order gt WARNING IN MOVING WASHING MACHINE When carrying washing machine please make sure two people move by grabbing handles on both sides If you carry it with its front part on your back or on your knee it might warp the shape or cause some damage TROUBLESHOOTING gt Washing machine won t work Is the water tap opened Is the washer plugged in Is the power cut off Is there enough water gt Spinning does not work Is the laundry spread out evenly in the washer Is the washer set on a sturdy flat surface gt Water is not supplied Is the water tap opened F Is the water cut off gt Water is overflowed Is the water supply hose or hose Restart after spinning If the error sign still indicates connection clogged 6 E call agency Is the water tap frozen If water is not supplied in 1 hour a buzzer will sound and the remaining time indicator will show 4E gt Water dose not drain Is the drain hose down No pump Is the drain hose frozen Is the drain hose clogged If the water dose not drain in 15 minutes a buzzer will sound and the remaining time indicator will show 5E 10 IN CASE THE NEED FOR SERVICING ARISES If any problem occurs with your products do not hestitate to call any nearby Name address telephone number is required SPE
9. for common use Make use of the User s Manual depending upon your washing machine model ENVIRONMENT Never install the washer near water Leave some space Do not place the washer in steamy rooms or where the Maintain at least 10cm between the washer and the wall washer is directly exposed to rain Moisture may destroy the Place the washer on a sturdy flat surface electrical insulation causing an electrical shock hazard If the washer is placed on an uneven or weak surface Avoid direct sunlight or heaters noise or vibration occurs Allowable is 1 As plastic and electrical components are affected by direct Adjust the legs for even placement heat never place the washer near furnaces boilers etc Do not place under direct sunlight gt LEVELLING If the washer is not leveled with the ground it makes the machine tremble more or be out of order So make sure that the washer is leveled properly SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING 1 Adjust the side horizontally o637on THE POSITION OF THE WASHING TUB first and the front i e Open the lid of the machine pour water into the tub up to the level in same direction next just below the pulsator and adjust the legs so that the pulsator is positioned at the center of the water as shown in the figure 2 If the thread is not e Place the machine more than within the limit adjust 10cm away from the wall the height of the legs e Adjust the legs on feet for levell
10. function is needed during the laundry Push the Course button and get the function started Note You cannot perform the function without the Power button on In the event that you would like to modify the Child Lock function L signal flashes in the signal window showing the rest of the set time every two seconds which means it is locked and indicates how much time is left until the function is released To release the function of Child Lock In case the Child Lock is programmed press both the Function and Course buttons in sequence Option Option GBRO pee eecete eects FILTER iB D WATER SUPPLY HOSE HOT Be sure to keep the lid WATER SUPPLY HOSE COLD closed during washing SbYion T cacaine E a Option S E ta a DRAIN HOSE PUMP Noo Oo option Lint will be collected in N E the filter during DETERGENT BOX washing FABRIC SOFTENER gt DISPENSER BLEACH INLET Spron 7 PULSATOR a option ey icn rs A Wi GROUND LEAD PTO When the water pipe is FRONT CONTROL p metal make sure to cover PANEL the end of the ground wire paa A Option oe WATER DRAIN HOSE ADJUSTABLE LEGS Adjust the length of the legs when Option installing the washer A RAT PROTECTION PANEL Japoul uryovu Surysvom 4noh uodn Suipuadap pnuvy s asn ayy fo asn yow ISN UOWULOD AOf S1 PNUD S
11. ght be serious injury or fatal accident when you violate this instruction If the power supply cord or plug is damaged or loosened do not use e An electric shock or a fire may take place Do not pull the cord off or touch it with moist hands e An electric shock or a fire may take place Do not bend the power supply cord by force or press it with heavy things e An electric shock or a fire may take place Do not install the washer nearby electric implement or don t put a candle light or cigarette light on the washer e A fire may take place Do not disassemble repair or remodel it recklessly e When you need to repair it please call service agent An electric shock or a fire may take place During operation do not put your hands or metal materials under the washer e You may be hurt by spinning board beneath the washer Stay away from the washer when the bottom of the washer sinks into the water e There might be an electric shock Please wait until the water drains out completely Do not put laundry stained with gasoline benzene or alcohol in the washer and keep the materials away from the washer e An explosion or a fire may take place During spinning don t put your hand in the spinning tub e It may hurt your hands If it does not stop within 15 seconds after you open the lid call service agent immediately CAUTIONS There might be a slight injury or damage when you violate this instruction Don t
12. ing ANY Loosen amp 3 Lock gt CONNECTING THE WATER SUPPLY HOSE Remove the adaptor from the water Option 5 Connect the other end of the water supply hose to the inlet water valve supply hose at the back of the washer Screw the hose clockwise all the way in 2 First using a type Optom 5 1 Connect the other end of the water screw driver loosen the four screws on the adaptor Next take the adaptor and turn part b following the arrow for gap about 5mm between them supply hose to the inlet water valve J at the top of the washer TA Screw the hose clockwise all the way in kD w Connect adaptor to the water tap by tightening the screws firmly Then turn part b following the arrow and put a and b together Option If the water tap is a screw type assemble a water supply hose that fits to the tap as shown NOTICE After completing connection if water leaks from the hose then repeat the same steps Use the most conventional type of faucet for water supply In case the faucet is square or too big remove the spacing ring before inserting the faucet into the adaptor 4 Connect the water supply hose to the adaptor Pull down the part c of the water supply hose When the part c is released the hose is automatically connected to the adaptor making a click sound gt ASSEMBLING THE RAT PROTECTION PANEL 1 Insert the rat prote
13. of detergent evenly so the detergent may not brim over the box j eeen Detergent Device sedecensieceesbipceableasineneesesateesenti eestbisessaternsntennersnig Put the detergent in proportion to water level Softener Device Softener _ baseline CAUTION If softener is stored over the above base line it may flow down at any time 8 gt WATER SUPPLY CONNECTOR FILTER gt on 7 ZR 5 inlet water valve 1 Pull out the filter and wash well 2 Pull in the filter and connect 3 Check if there is a leakage the hose to the inlet water Note to tighten up the valve tightly connector gt CLEANING THE FILTER NET Clean the filter net often to keep the washer clean gt 7on ig 1 Push the upper part 2 Open the cover as 3 Clean the filter 4 Close the cover and insert the of the filter and pull in shown in the figure lower part of the filter in the basket first and then push the filter with click sound 1 Push up and 2 Remove the collected 3 Clean the filter 4 Pull down the filter net pull out the filter net lint from the filter net gt HOW TO CLEAN THE FILTER 1 Place a rag under the washer filter not to wet the floor pump drained washer 2 Rotate the filter counterclockwise 1 Place a rag under washer filter not to wet the floor and pull out the filter 2 Turn the filter cap to the left 3 Remove dirts and rotate 3 Take the filter out and th
14. to ON 2 Press the course select three times 3 Press the START HOLD button Washing rinsing and spinning follow If you want to pause press the START HOLD button again You can change the course when paused 4 Close the lid CAUTION Do not use water above 30 C for WOOL washing Refer to the tag attached on the clothes for washing information Fasten buttons and turn inside out before washing Use the detergent indicated in the laundry When the degree of dirt is extreme soak the laundry in warm water for about 10 minutes before pressing the WOOL course button in order to enhance washing efficiency gt DELAY START COURSE roy gt came gt CEA gt SER Select this course when you have to go out or do something else 1 Press the power button to ON 2 Press the DELAY START button once You may change the delay start time with use the DEALY START button from 3 hours to 18 hours 3 Press the START HOLD button and put the proper amount of detergent into tub 4 Close the lid The washing finishes by the time you reserved MANUAL FUNCTIONS Each washing course changes manually Ex If you want to wash in the speedy course Power Select speedy course Wash Start Hold button POWER gt COURSE rnc gt wo once SOAK FUNCTION Including WASH RINSE SPIN Press the POWER button Select the course Press the course button gt FUZZY BLANKET SPEED WOOL Press the FUNCTION
15. uriosity of users to see inside of washing machine while operation While operation the laundry progress inside of washing machine can be checked by looking through the transparent window PULSATOR b on e The Pulsator helps water and detergent to go through fabrics efficiently while providing both the powerful water action to clean larger and heavier clothes and the gentle water action to clean all delicates with less wear and tear on clothes WATERFALL FLOW e The Waterfall Flow injected from under the pulsator cascades with full force back into the tub pushing down any clothes that float right under the water surface It is this Waterfall Flow that enables this washing machine to effectively wash large and heavy items such as bluejeans and blankets MAGIC FILTER tion e This unique magic Filter ensures that all the lint inside the tub is captured for top quality filtering results to deliver consistently effective cleaning results SOFTENER DISPENSER e The Softener Dispenser releases the fabric softener at the appropriate time when the last rinsing proceeds SAFETY INSTRUCTIONS Please note that the following precautions for safety intend to prevent unpredictable danger and damage by helping the proper use in safety When using hot water in washing please make sure that the water should not exceed 50 C e Plastic parts may be deformed or damaged and an electric shock or a fire may take place WARNING There mi
Download Pdf Manuals
Related Search