Samsung AVMDH052EA0 User Manual
Contents
1. 4 Select the fan speed by pressing the Fan button one or more times until the intended value is displayed a Automatic rotated 25 r T Low Medium ul High Heating Your Room Except Cooling Only Models You can select the HEAT mode only in heat pump models ENGLISH You must select the HEAT mode if you wish to adjust the Heating temperature Fan speed when heating 1 If necessary press ON OFF button Result The On Off indicator on the wired remote controller comes on The air conditioner runs in the mode selected when the unit was last used PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 To select the HEAT mode press the Mode button until x is displayed at the top of the wired remote controller Result The air conditioner runs in HEAT mode Note You can change modes at any time 3 To adjust the temperature press the Temperature buttons one or more times until the required temperature is displayed Possible temperatures are between 16 C and 30 C inclusive Result Each time you press Temperature buttons The temperature is adjusted by 1 C The air conditioner starts heating provided that the room temperature is lower than the selected temperatu2. Centralized Controller The centralized controller is an optional accessory and it is installed on the wall Operating lamp All On button AI All Off button On Off indicators SS On Off buttons Index Note Operating lamp comes on when at least one air conditioner connected to the centralized controller is operating ENGLISH Getting Start You have just purchased a system type air conditioner and it has been i installed by your installation specialist Your Owner s Instructions contain much valuable information on using your air conditioner Please take the time to read them as they will help you take full advantage of the unit s features The booklet is organized as follows Thefollowing figures are shown on pages from 4 to 9 Indoor and outdoor units Wireless remote controller buttons and display Thereceiver amp display unit Wired remote controller buttons and display Centralized controller Inthe main part of the document you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use three different symbols HOLD DOWN Inserting the Wireless Remote Controller Batteries ENGLISH You must insert or replace the remote controller batteries when You purchase the air conditioner The remote controller does not work correctly Note Use two AAA LRO3 1
3. adjust the temperature press the Temperature buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press Temperature buttons The temperature is adjusted by 1 C The receiver amp display unit beeps The air conditioner starts cooling provided that the room temperature is higher than the selected temperature the fan will however operate 4 Select the fan speed by pressing the Fan button one or more times until the intended value is displayed 43 1 Automatic rotated 4 r T Low sfa Medium Seal High Heating Your Room Except Cooling Only Models You can select the HEAT mode only in heat pump models You must select the HEAT mode if you wish to adjust the Heating temperature Fan speed when heating 1 If necessary press ON OFF button Result The On Off indicator on the receiver amp display unit comes on The air conditioner runs in the mode selected when the unit was last used The receiver amp display unit beeps PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes C 2 To select the HEAT mode press the Mode button until xx is displayed at the top of the wireless remote con
4. timer reaches the setting time press the ON OFF button Setting the Off Timer The Off Timer enables you to switch off the air conditioner automatically after a given period of time You can set the period of time from 30 minutes to 24 hours 1 Tosetthe operating time press the Off Timer button one or more times until the required time is displayed Possible time is between 0 5 hour and 24 hour inclusive Result Each time you press Off Timer button The time is adjusted by 0 5 hour to 5 hours by 1 hour from 6 hours to 24 hours 2 Pressthe Set Cancel button to complete the setting Result The remaining time is displayed Blinking of the timer indicator stops The air conditioner will switch off automatically when the counter displayed on the remote controller reaches the setting time as disappearing the Off timer setting If you would like to turn the air conditioner on after 2 hours and to operate it for 2 hours 1 Press the On Timer button until 2 0 Hr is displayed 2 Press the Set Cancel button 3 Press the Off Timer button until 4 0 Hr is displayed 4 Press the Set Cancel button Note You can see or change the setting mode and or the temperature by pressing the Mode button or the Temperature buttons after setting the Off timer To Cancel the Off Timer 1 Tocancel the Off Timer press the Off Timer button one or more times until the timer setting disappears 2 Pres
5. 5V batteries Do not use old batteries or different kinds of batteries together Batteries may be completely discharged after 12 months even if they have not actually been used 1 Push the battery cover on the rear of the remote controller with your thumb in the direction of the arrow and remove it 2 Insert the two batteries taking care to respect the polarities on the battery with on the remote controller on the battery with on the remote controller 3 Close the cover by sliding it back until it clicks into place This chapter indicates how to operate and program your air conditioner with the wireless remote controller The wireless remote controller is an optional accessary Selecting the Automatic Operation Mode In the Automatic mode the room temperature and the fan speed are controlled automatically 1 If necessary press ON OFF button Result The On Off indicator on the receiver amp display unit comes on The air conditioner runs in the mode selected when the unit was last used The receiver amp display unit beeps PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 To select the AUTO mode press the Mode button until is displayed at the top of the wireless remote controller R
6. OWNER S INSTRUCTIONS MANUAL DE INSTRUCCIONES MANUEL D UTILISATION ISTRUZIONI PER LUSO _ E MANUAL DE INSTRUCOES GEBRAUCHSANWEISUNG 3 5 Heat pump Cooling only AVMDHO52CAO AVMDC052CA0 2 2 AVMDC072CA0 AVMHH105CAO AVMHC105CA0 AVMHH128CA0 AVMHC128CA0 AVMDH052EA B 0 AVMDC052EA B 0 AVMDHO70EA B O AVMDCO70EA B O AVMHH105EA B 0 AVMHC105EA B O AVMHH128EA B 0 AVMHC128EA B 0 e z Ed Ed E System Air Conditioner Aire acondicionado sistem tico Climatiseur num rique multifonctionnel Sistema Aria Condizionata Sistema Ar Condicionado Klimaanlage System gt KAIPaTIOWOU RUSSIAN EAAHNIKA DEUTSCH PORTUGU S BSP DVPD GB DB98 05146A 1 Safety Precautions N WARNING N DANGER J N CAUTION If the power supply cord of this air conditioner is damaged it must be replaced by the manufacturer or its authorized service personnel only in order to avoid a safety hazard Do not attempt to install this air conditioner by yourself This unit contains no user serviceable parts Always consult authorized service personnel for repairs When moving consult authorized service personnel for disconnection and installation of the unit Do not become over exposed to cold air by staying in the direct path of the airflow of the air conditioner for extended periods of tim
7. R AIR CONDITIONER m Selecting the Automatic Operating Mode 21 m Cooling Your 22 m Heating Your Room Except Cooling Only Models 23 m Removing Excess Humidity 24 m Airing Your Room 25 PROGRAMMING YOUR AIR CONDITIONER m Setting the On 26 m Setting the Off Timer 27 USING CENTRALIZED CONTROLLER m Using the Centralized Controller 28 RECOMMENDATIONS FOR USE m Operating Recommendations 29 m Cleaning Your Air Conditioner 30 m Temperature and Humidity Ranges 32 m Solving Common Problems 33 TECHNICAL SPECIFICATIONS ENGLISH View of the Unit The figures are shown in this instruction may differ from yours depending on the model indoor rit 05210701072 i Air filter inlet 39105 1283e 1 Air outlet Connection valve Air outlet Connection valve Air outlet Connection valve Air outlet 88 8 8 NN LILI ZU Connection valve Air outlet Connection valve Note If the heat exchanger in the outdoor unit gets dusty cooling efficiency may fall So clean the heat exchanger with water when it becomes dirty However be careful when you wa
8. cept Cooling Only Models QG Filter sign indicator I Remote control sensor On Off indicator Timer indicator Wired Remote Controller Buttons and Display The wired remote controller is an optional accessory and it is installed on the wall Operating mode Centralized controller indicator In case of installing the Centralized controller Removing frost indicator Except Cooling Only Models Communication error indicator fs CENTRAL ZED cru mM NUN setting On Timer setting L S H 4 H H C D Fan speed Off Timer setting 1 SAS Air flow direction Test indicator Filter Sign indicator On Off amp Timer Set Cancel button On Off indicator Temperature adjustment buttons On Timer button Fan speed adjustment button Off Timer button Swing button Not operated Test button Filter Reset button Mode selection button Note Test button is for your installation specialist You must NOT press it After cleaning the air filter press the filter reset button Then the wired remote controller will display the FILTER SIGN indicator when the time to clean the air filter refer to page 30 or 31 Duct type air conditioner does not have function of adjusting air flow direction Therefore the function is not operated even if you press the swing button The heating mode xx is not selected in cooling only models
9. e Do not insert fingers or objects into the outlet port or intake grilles Do not start and stop air conditioner operation by disconnecting the power supply cord and so on Take care not to damage the power supply cord In the event of a malfunction burning smell etc immediately stop operation turn off the electrical breaker and consult authorized service personnel Provide occasional ventilation during use Do not direct air flow at fireplaces or heating apparatus Do not climb on or place objects on the air conditioner Do not hang objects from the indoor unit Do not set flower vases or water containers on top of air conditioners Do not expose the air conditioner directly to water Do not operate the air conditioner with wet hands Do not pull power supply cord Turn off power source when not using the unit for extended periods Check the condition of the installation stand for damage Do not place animals or plants in the direct path of the air flow Do not drink the water drained from the air conditioner Do not use in applications involving the storage of foods plants or animals precision equipment or art works Do not apply any heavy pressure to radiator fins Operate only with air filters installed Do not block or cover the intake grille and outlet port Ensure that any electronic equipment is at least one metre away from either the indoor or outdoor units Avo
10. esult The receiver amp display unit beeps The air conditioner runs in AUTO mode Note You can change modes at any time 3 To adjust the temperature press the Temperature buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press Temperature buttons The temperature is adjusted by 1 C The air conditioner starts cooling provided that the room temperature is higher than the selected temperature The quantity of air is adjusted automatically ENGLISH Cooling Your Room You must select the COOL mode if you wish to adjust the Cooling temperature Fan speed when cooling 1 If necessary press ON OFF button Result The On Off indicator on the receiver amp display unit comes on The air conditioner runs in the mode selected when the unit was last used The receiver amp display unit beeps PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 To select the COOL mode press the Mode button until is displayed at the top of the wireless remote controller Result The receiver amp display unit beeps The air conditioner runs in COOL mode Note You can change modes at any time 3 To
11. id installing the air conditioner near a fireplace or other heating apparatus When installing the indoor and outdoor unit take precautions to prevent access to infants Do not use inflammable gases near the air conditioner Max input power amp current is measured according to IEO standard and input power amp current is measured according to ISO standard Contents PREPARING YOUR AIR CONDITIONER m Safety Precautions 2 m View of the 4 m Wireless Remote Controller Buttons and Display 6 m The Receiver amp Display 7 m Wired Remote Controller Buttons and Display 8 m Centralized Controller 9 Getting 10 m Inserting the Wireless Remote Controller Batteries 11 USING WIRELESS REMOTE CONTROLLER OPERATING YOUR AIR CONDITIONER m Selecting the Automatic Operating Mode 13 m Cooling Your 14 m Heating Your Room Except Cooling Only Models 15 m Removing Excess Humidity 16 m Airing Your Room 17 PROGRAMMING YOUR AIR CONDITIONER m Setting the On 18 m Setting the Off Timer 19 USING WIRED REMOTE CONTROLLER OPERATING YOU
12. ilter into the unit 6 Reinstall the fixing bracket Note After cleaning the air conditioner press the Filter Reset button Wired Remote Controller ENGLISH om Wireless Remote Controller CS QZ Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used If the air conditioner is used at Then High temperature The automatic protection feature may be triggered and the air conditioner stopped Low temperature A water leakage or some other malfunction may happen if the heat exchanger freezes High humidity levels Water may condense on and drip from the surface of the indoor unit if it is used for a long periods Mode Outdoor Temperature Indoor Temperature Indoor Humidity Heating 20 to 24 approx 27 or less Cooling 5 C to 43 C approx 21 C to 32 C approx 80 or less Drying 5 to 43 C approx 18 to 32 C approx If the heating operation is used at below 0 C outdoor temperature then it does not heat at its full capacity If the cooling operation is used at over 33 C indoor temperature then it does not cool at its full capacity Solving Common Problems ENGLISH Before contacting the after sales service perform the following simple checks They may save your time and expense of an unnece
13. ou must clean it regularly to remove the dust that accumulates on the air filter PORTANT Before cleaning your air conditioner ensure that you have switched off the electric circuit breaker used for the unit 1 Turn the levers to the right or left not to prevent pulling out the air filter 2 Pull out the air filter 3 Remove all dust on air filter with a vacuum cleaner or a brush In case of serious dust accumulation put the air filter in warm detergent water and shake it vertically 4 Dry the air filter 5 When you have finished insert the filter into the unit 6 Return the levers Note After cleaning the air conditioner press the Filter Reset button Wired Remote Controller Wireless Remote Controller EI c Cleaning Your Air Conditioner 31 05 128 To get the best possible use out of your air conditioner you must clean it regularly to remove the dust that accumulates on the air filter PORTANT Before cleaning your air conditioner ensure that you have switched off the electric circuit breaker used for the unit 1 Remove the fixing bracket on the base of air filter kit 2 Pullout the air filter in the direction of the arrow 3 Remove all dust on air filter with a vacuum cleaner or a brush In case of serious dust accumulation put the air filter in warm detergent water and shake it vertically 4 Dry the air filter 5 When you have finished insert the f
14. played on the remote controller reaches the setting time as disappearing the On timer setting Note You can see or change the setting mode and or the temperature by pressing the Mode button or the Temperature buttons after setting the On timer To Cancel the On Timer 1 Tocancel the On Timer press the On Timer button one or more times until the On timer setting disappears 2 Press the Set Cancel button Note Ifyou want to turn on the air conditioner before the timer reaches the setting time press the ON OFF button Setting the Off Timer ENGLISH The Off Timer enables you to switch off the air conditioner automatically after a given period of time You can set the period of time from 30 minutes to 24 hours 1 Tosetthe operating time press the Off Timer button one or more times until the required time is displayed Possible time is between 0 5 hour and 24 hour inclusive Result Each time you press Off Timer button The time is adjusted by 0 5 hour to 5 hours by 1 hour from 6 hours to 24 hours 2 Pressthe Set Cancel button to complete the setting Result The remaining time is displayed Blinking of the timer indicator stops The air conditioner will switch off automatically when the counter displayed on the remote controller reaches the setting time as disappearing the Off timer setting If you would like to turn the air conditioner on after 2 hours and
15. re the fan will however operate 4 Select the fan speed by pressing the Fan button one or more times until the intended value is displayed Automatic rotated DAP Low Medium ul High Removing Excess Humidity If the atmosphere in your room is very humid or damp you can remove excess humidity without lowering the room temperature too much 1 If necessary press ON OFF button Result The On Off indicator on the wired remote controller comes on The air conditioner runs in the mode selected when the unit was last used PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 select the DRY mode press the Mode button until e is displayed at the top of the wired remote controller Result The air conditioner runs in DRY mode Note You can change modes at any time 3 To adjust the temperature press the Temperature buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press Temperature buttons The temperature is adjusted by 1 C The air conditioner starts removing the excess humidity The quantity of air is adjusted automatically Note Inthe dry mode the fan speed is cont
16. rolled automatically Airing Your Room If the atmosphere in your room is stale you can air it using the FAN feature 1 If necessary press ON OFF button Result The On Off indicator on the wired remote controller comes on The air conditioner runs in the mode selected when the unit was last used 2 To select the FAN mode press the Mode button until of is displayed at the top of the wired remote controller Result The air conditioner runs in FAN mode 3 Select the fan speed by pressing the Fan button one or more times until the intended value is displayed Low Tu Medium alb High ENGLISH Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time You can set the period of time from 30 minutes to 24 hours 1 Tosetthe operating time press the On Timer button one or more times until the required time is displayed Possible time is between 0 5 hour and 24 hours inclusive Result Each time you press On Timer button The time is adjusted by 0 5 hour to 5 hours by 1 hour from 6 hours to 24 hours 2 Pressthe Set Cancel button to complete the setting Result The remaining time is displayed Blinking of the timer indicator stops The selected mode and the temperature disappear on the display after 5 seconds The air conditioner will switch on automatically when the counter dis
17. s the Set Cancel button Note Ifyou want to turn off the air conditioner before the timer reaches the setting time press the ON OFF button JBL ete N g Ww 2 3 z 2 ENGLISH Using MW drat RAMON Controllar This chapter indicates how to operate and program your air conditioner with the wired remote controller The wired remote controller is an optional accessory Selecting the Automatic Operating Mode In the Automatic mode the room temperature and the fan speed are controlled automatically 1 If necessary press ON OFF button Result The On Off indicator on the wired remote controller comes on The air conditioner runs in the mode selected when the unit was last used PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 To select the AUTO mode press the Mode button until i is displayed at the top of the wired remote controller Result The air conditioner runs in AUTO mode Note You can change modes at any time 3 To adjust the temperature press the Temperature buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press Temperat
18. s until the intended value is displayed T Low ANI Medium all High e Filter Reset e JE Q E 3 E 3 A 0 ENGLISH Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time You can set the period of time from 30 minutes to 24 hours 1 Tosetthe operating time press the On Timer button one or more times until the required time is displayed Possible time is between 0 5 hour and 24 hour inclusive Result Each time you press On Timer button The time is adjusted by 0 5 hour to 5 hours by 1 hour from 6 hours to 24 hours 2 Pressthe Set Cancel button to complete the setting Result The remaining time is displayed Blinking of the timer indicator stops The selected mode and the temperature disappear on the display after 5 seconds The air conditioner will switch on automatically when the counter displayed on the remote controller reaches the setting time as disappearing the On timer setting Note You can see or change the setting mode and or the temperature by pressing the Mode button or the Temperature buttons after setting the On timer To Cancel the On Timer 1 Tocancel the On Timer press the On Timer button one or more times until the timer setting disappears 2 Pressthe Set Cancel button Ifyou want to turn on the air conditioner before the
19. sh the surface of the heat exchanger because it is very sharp ENGLISH Wireless Remote Controller Buttons and Display The wireless remote controller is an optional accessory Mode selection button Operating mode T T Temperature adjustment Temperature setting E uttons Filter Reset button Fan speed f Fan speed adjustment a button Air flow direction 31 1 Swing button Not operated On Timer setting 4 On Timer button Off Timer setting 1 Off Timer button Battery discharge indicator 3 On Off amp Timer Set Cancel button Note After cleaning the air filter press the filter reset button Duct type air conditioner does not have function of adjusting air flow direction Therefore the function is not operated even if you press the swing button The heating mode x is not selected in cooling only models The Receiver amp Display Unit The Receiver amp Display unit is an optional accessory and it is installed on the wall ENGLISH congealed Type Filter sign indicator Fan indicator Timer indicator 00 dq 0 Remote control sensor Heat Pump Models On Off indicator Green amp Removing frost indicator Red Cooling Only Models On Off indicator Removing frost indicator Ex
20. ssary call Problem Explanation Solution The air conditioner does not Check that the breaker used for the air conditioner is switched on operate at all Wired Remote Controller The air conditioner does not is displayed on the wired remote controller In this case operate with the remote turn the air conditioner off and contact your dealer controller Wired Remote Controller When turning on off the case of using the wired remote controller for a group the air air conditioner it is not conditioners connected to the remote controller are turned on off in turned on off immediately order Thus it takes some time up to 32 seconds Wireless Remote Controller The air conditioner does not Check that there are no obstacles between you and the remote operate with the remote control sensor controller Check the wireless remote controller batteries Refer to page 11 Check that you are close enough to the remote control sensor seven metres yards or less Wireless Remote Controller No beep is heard when Check that you are pointing the remote controller at the remote press ON OFF on the control sensor on the receiver amp display unit remote controller Replace the remote controller batteries if necessary If there is a strong light around the air conditioner a three wavelength light a neon sign etc for example the air conditioner may not be operated with a remote controller If
21. t the DRY mode press the Mode button until e is displayed at the top of the wireless remote controller Result The receiver amp display unit beeps The air conditioner runs in DRY mode Note You can change modes at any time 3 To adjust the temperature press the Temperature buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press Temperature buttons The temperature is adjusted by 1 C The receiver amp display unit beeps The air conditioner starts removing the excess humidity The quantity of air is adjusted automatically Note Inthe dry mode the fan speed is controlled automatically Airing Your Room If the atmosphere in your room is stale you can air it using the FAN feature 1 If necessary press ON OFF button Result The On Off indicator on the receiver amp display unit comes on air conditioner runs in the mode selected when the unit was last used The receiver amp display unit beeps 2 To select the FAN mode press the Mode button until sk is displayed at the top of the wireless remote controller Result The receiver amp display unit beeps The air conditioner runs in FAN mode Note You can change modes at any time Filter Rese OOR Is 3 Select the fan speed by pressing the Fan button one or more time
22. this happens use the remote controller close by the remote control sensor The air conditioner does Check that the correct operating mode has been selected not cool or heat The room temperature be too low or too high Dust may be blocking the air filter guard refer to page 30 or 31 for cleaning instructions Check that there is no obstacle in front of the outdoor unit When heating the required Check that the required temperature has been set correctly room temperature is never Increase the fan speed reached and the air conditioner frequently stops Technical Specifications Model Power Supply AVMDH052CA0 AVMDH072CA0 AVMHH105CA0 AVMHH128CA0 AVMDC052CA0 AVMDC072CA0 AVMHC105CA0 AVMHC128CA0 19 208 230V 60Hz AVMDHOS2EA B O AVMDHO7OEA B O AVMHH105EA B O AVMHH128EA B O 10 220 240V 50Hz AVMDCOS2EA B O AVMDCO7OEA B O AVMHC105EA B 0 AVMHC128EA B 0 HSI TON3 THIS AIR CONDITIONER IS MANUFACTURED BY ESTE AIRE ACONDICIONADO HA SIDO FABRICADO POR CE CLIM ATISEUR EST FABRIQUE PAR QUESTO CONDIZIONATORE D ARIA E PRODOTTO DA ESTE APARELHO DE AR CONDICIONADO E FABRICADO POR DIESE KLIM AANLAGE IST FABRIZIERT VON AYTH H ZYZKEYH KATAZKEYAZTHKE ATIO l ELECTRONICS Printed in Korea
23. to operate it for 2 hours 1 Press the On Timer button until 2 0 Hr is displayed 2 Press the Set Cancel button 3 Press the Off Timer button until 4 0 Hr is displayed 4 Press the Set Cancel button Note You can see or change the setting mode and or the temperature by pressing the Mode button or the Temperature buttons after setting the Off timer To Cancel the Off Timer 1 Tocancel the Off Timer press the Off Timer button one or more times until the timer setting disappears i gt ig 4 2 Pressthe Gi button Note Ifyou want to turn off the air conditioner before the timer reaches the setting time press the 2 button Using the Centralized Controller The centralized controller is an optional accessory Up to sixteen air conditioners can be tumed on or off by connecting to the centralized controller However you cannot adjust the cooling temperature or set the timer with it If you also have the wired remote controller CENTRALIZED CONTROL is displayed at the top of the remote controller 1 Toturn on the all of air conditioners connected to the centralized controller press the All ON button 2 To turn on off a specific air conditioner press the ON OFF button Result The On Off indicator comes on when the air conditioner is operating 3 Toturn off the all of air conditioners connected
24. to the centralized controller press the All OFF button Operating Recommendations ENGLISH Here are a few recommendations that you should follow when operating your air conditioner Topic Recommendation Heating The heat pump function of the air conditioner absorbs heat performances from outside air and brings it indoors As the temperature of the outside air drops the heating performance of air conditioner will decrease If you find that the room is not warm enough using an additional heating appliance is recommended Frost When outside temperature is low but humidity is high frost may form on the outdoor unit at HEAT mode If this happens The heating operation stops The defrost mode will be triggered automatically for about ten minutes No intervention is required after about ten minutes the air conditioner operates again normally High indoor If both indoor and outdoor temperatures are high and the air and outdoor conditioner is running at HEAT mode the outdoor unit s fan temperatures compressor may stop at times This is normal simply wait until the air conditioner switches on again Power failure If a power failure occurs while the air conditioner is operating the unit will be switched off When the power returns the air conditioner starts up again automatically Cleaning Your Air Conditioner 052 070 072 To get the best possible use out of your air conditioner y
25. troller Result The indoor unit beeps The air conditioner runs in HEAT mode Note You can change modes at any time 3 Toadjust the temperature press the Temperature buttons one or more times until the reguired temperature is displayed Possible temperatures are between 16 C and 30 C inclusive Result Each time you press Temperature buttons The temperature is adjusted by 1 C The indoor unit beeps The air conditioner starts heating provided that the room temperature is lower than the selected temperature the fan will however operate 4 Select the fan speed by pressing the Fan button one or more times until the intended value is displayed sap Automatic rotated gt T Low Medium Sail High ENGLISH Removing Excess Humidity If the atmosphere in your room is very humid or damp you can remove excess humidity without lowering the room temperature too much 1 If necessary press ON OFF button Result The On Off indicator on the receiver amp display unit comes on The air conditioner runs in the mode selected when the unit was last used The receiver amp display unit beeps PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 selec
26. ure buttons The temperature is adjusted by 1 C The air conditioner starts cooling provided that the room temperature is higher than the selected temperature The quantity of air is adjusted automatically ENGLISH Cooling Your Room You must select the COOL mode if you wish to adjust the Cooling temperature Fan speed when cooling 1 If necessary press ON OFF button Result The On Off indicator on the wired remote controller comes on The air conditioner runs in the mode selected when the unit was last used PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 select the COOL mode press the Mode button until is displayed at the top of the wired remote controller Result The air conditioner runs in COOL mode Note can change modes at any time 3 To adjust the temperature press the Temperature buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press Temperature buttons The temperature is adjusted by 1 C The air conditioner starts cooling provided that the room temperature is higher than the selected temperature the fan will however operate
Download Pdf Manuals
Related Search