Samsung GN752CFX User Manual
Contents
1. 44 1 INSTALLING YOUR APPLIANCE e Gas supplied by tank or cylinder butane propane For your safety you must choose from the three following connection options Connection with a reinforced copper pipe with screw on mechanical connectors compliant with the G1 2 standard Make the connection directly to the end of the elbow fitted on the appliance Connection with a wavy metal hose stainless steel with screw on mechanical connectors whose service life is unlimited Fig 01 Connection with a reinforced flexible rubber hose with screw on mechanical connectors whose service life is 10 years Fig 02 In an existing system a soft pipe fitted with clamps whose service life is five years may be used It is necessary in this case to use an adaptor without forgetting to fit a sealing washer between the adaptor and the hob s bent Fig 03 fal fe You can obtain the adaptor and the sealing washer from your After Sales Service Department Warning Screw on the adaptor with a torque not exceeding 25 N m Q Sealing washer not supplied B Adaptor not supplied Q Clamp not provided Warning All soft pipes and hoses whose service life is limited must have a maximum length of two meters and must be accessible along their entire length They must be replaced before the end of their service life indicated on the pipe Regardless of the means of connection chosen ensure that the c2. burner it allows for better flame Fig 01 distribution around large cookware such as woks and paella dishes with large diameters FN Warning Adjust the ring of flames so that they do not extend beyond the edges of the cookware Fig 02 Do not use cookware with a concave or convex bottom Fig 03 Do not use cookware that partially covers the knobs Fig 04 Do not leave a gas burner operating with empty cookware CONCAVE 52 3 DAILY CARE OF YOUR APPLIANCE Maintaining your appliance MAINTENANCE HOW TO PROCEED PRODUCTS ACCESSORIES TO USE Of the spark plugs In the event that the spark plugs Small hard bristled brush and injectors become soiled clean them using a small hard bristled brush non metallic Safety pin The gas injector is located in the centre of the burner in the shape of a dish Be careful not to obstruct it during cleaning as this will undermine the performance of your hob In the event of obstruction use a Safety pin to unclog the injector Of the pan In the event of tough stains use a non Gentle scrubbing cream supports and gas abrasive cream then rinse with clean burners water Carefully wipe each part of the Cleaning sponge burner before using your hob again Of the enamel or It will be easier to maintain your hob if Gentle scrubbing cream stainless steel you clean it before it has completely a cooled down Commercially a
3. 50 1 50 1 55 Reduced heat release rate kW 0 700 0 650 Hourly rate g h 109 107 Hourly rate I h 148 AUXILIARY BURNER Marking engraved on injector 50 50 63 Nominal heat release rate kW 0 90 0 90 0 85 Reduced heat release rate kW 0 350 0 300 Hourly rate g h 65 64 Hourly rate I h 81 5 GAS BURNERS WITH DOUBLE CROWN Total heat release rate kW 11 15 11 15 11 55 Maximum fow rate g h 810 796 I h 1100 49 2 USING YOUR APPLIANCE DESCRIPTION OF THE TOP GN 752 Auxiliary burner 0 85 kW High speed burner 2 25 kW Q Super fast burner 3 10 kW Semi fast burner 1 55 kW 6 Double crown burner 3 8 KW Power obtained with natural gas G20 50 2 USING YOUR APPLIANCE SWITCHING ON GAS BURNERS The burner safety measure is a metal rod located directly to the side of the flame Each burner is controlled by a tap fitted with a safety system that in the event of accidental flame extinction spills draughts etc quickly and automatically cuts the gas supply and prevents it from being released Each burner is supplied by a tap that is opened when you press in the knob and turn it in a counterclockwise direction The point corresponds to a closed tap Select the desired burner by referring to the symbols located ne
4. combustion by product disposal system It must be installed and connected in compliance with all applicable laws Special care should be given to applicable regulations concerning ventilation Do not store CLEANING products or FLAMMABLE products aerosol cans or containers under pressure as well as papers cookbooks etc in the cabinet underneath your cooking hob If you use a drawer located under the hob we recommend that you avoid storing in it items that are heat sensitive plastic papers aerosol cans etc Your hob should be disconnected from power and fuel supplies electricity and gas before any repairs are carried out When you connect the power cables of any electrical appliances plugged in close to the hob ensure that they are not in contact with the cooking zones As a safety measure do not forget to close the general supply tap for gas distributed by pipe or the tap of the tank for butane or propane gas after use The CE compliance designation is affixed to these hobs Installation should only be performed by installers and qualified technicians Before installation ensure that the conditions of local distribution gas type and pressure and the settings of the appliance are compatible This hob complies with the EN 60335 2 6 standard relative to the heating of cabinets and the Class 3 standard relative to installation according to the 30 1 1 standard Warning The req
5. 0 85 3 8 2 25 1 55 11 55 KW 11 55 KW x 2 23 10 m h of minimum air flow 1 INSTALLING YOUR APPLIANCE e GAS CONNECTION Preliminary comments If your hob is installed above an oven or if proximity to other heating elements poses a threat of overheating the connection you must insulate the cable in a rigid pipe If a flexible hose or tubing in the case of butane gas is used it should not come into contact with a moving part of the cabinet nor should it pass through a location that may become blocked The gas connection must be installed in compliance with applicable regulations in the country of installation e Gas distributed by pipe natural gas For your safety you must choose from the three following connection options Connection with a reinforced copper pipe with screw on mechanical connectors compliant with the G1 2 standard Make the connection directly to the end of the elbow fitted on the appliance Connection with a flexible wavy metal hose stainless steel with screw on mechanical connectors whose service life is unlimited Fig A Connection with a flexible rubber hose with screw on mechanical connectors whose service life is 10 years Fig B Warning When connecting your hob s gas supply if you have to change the direction of the elbow fitted on the appliance Change the gasket Screw on the elbow s nut careful not to exceed a torque of 17 N m
6. IT MANUALE PER L INSTALLAZIONE E L UTILIZZO SV INSTALLATIONS OCH ANV NDARMANUAL EN GUIDE FOR INSTALLATION AND USE Piano di cottura GN 752 Spish ll GN 752 Cooking Hob GN 752 a TABLE OF CONTENTS Safety Recommendations 39 Respect for the Environment 40 e Description of Your Appliance 41 1 INSTALLING YOUR APPLIANCE Proper positioning 42 e Flush mounting 42 e Tips for Flush Mounting 43 e Electrical connection 43 Gas connection 44 Changing the gas supply 46 2 USING YOUR APPLIANCE Description of the top 50 e Switching on gas burners 51 e Cookware to be used with gas burners 52 3 DAILY CARE OF YOUR APPLIANCE e Maintaining your appliance 53 4 SPECIAL MESSAGES DIFFICULTIES e During operation 54 5 COOKING CHART e Gas cooking guide 55 6 AFTER SALES SERVICE 56 38 SAFETY RECOMMENDATIONS SAFETY RECOMMENDATIONS We have designed this cooking hob for use by private persons in their homes This appliance must be installed in compliance with currently applicable regulations and used only in a well ventilated location Read this guide before installing and using your appliance All cooking should take place under your surveillance These cooking hobs are meant to be used exclusively for cooking foodstuffs and preparing beverages and do not contain any asbestos based materials This appliance is not connected to a
7. ar the knobs e g front right burner og Your hob is fitted with a burner lighting system built into the knobs To light a burner press on the knob and turn it in a counterclockwise direction gt to the maximum setting h Continue to press on the knob to produce a series of sparks until the burner lights The setting for more moderate flame intensities are between the symbol and the symbol CH In order to ensure the proper lighting of the double crown burner we suggest that you light it before placing cookware on it When a knob becomes difficult to turn do not force it Request an emergency service call from the installer Warning Hold the knob completely pressed down for a few seconds after the flame appears to trigger the safety system 2 USING YOUR APPLIANCE e COOKWARE TO BE USED WITH GAS BURNERS e Which burner should you use depending on your cookware Diameter of the cookware Diameter of the cookware Use 20 to 30 cm Double crown 18 to 28 cm Super fast Fried foods Boiling 16 to 28 cm High speed Searing foods 12 to 24 cm Semi fast Sauces Re heating 12 to 24 cm Auxiliary Gentle simmer Some hobs with five gas burners are equipped with a specific WOK type grid support Fig 01 that can only be used on the central double crown burner This WOK accessory allows you to use cookware with concave bases Combined with the double crown
8. dimensions below the work top damage the knobs and spark plugs To ensure a tight seal between the housing and the work top glue the foam seal along the exterior edge of the housing before installing the hob Fig 02 d If YM ma m 2 MM ET MM Mes MUM a MZ MM MM MM Mt 1 INSTALLING YOUR APPLIANCE TIPS FOR FLUSH MOUNTING Underside view of the housing Fig 02 i Cabinet Mounting brackets j Place your hob in the opening of the support cabinet carefully pulling the table toward you Reposition the burner heads burner covers and pan supports on the hob Connect your hob to the gas supply See Gas Connection chapter and to the power supply See Electrical Connection chapter If you wish you can immediately stabilise the hob with the four mounting brackets and screws supplied with the hob Fig 02 by attaching them to the four corners of the housing You must use the holes provided for this purpose as shown in the diagram above Fig 01 Stop screwing when the mounting bracket starts to become misshapen Do not use a screwdriver 43 ELECTRICAL CONNECTION Your hob is delivered with a power cable type HO5V2V2F T90 1mm cross section with three conductors phase ground neutral It must be con
9. ese position switches Gasket Burner power adjustment screw Tap axis 1 INSTALLING YOUR APPLIANCE Markings on the injectors MARKINGS ON THE INJECTORS The adjacent table shows where the injectors are positioned on your appliance according to N Example the type of gas used i Injector marking 94 Each number is marked on the injector Natural gas Butane Propane Gas See Description of the Top chapter 48 1 INSTALLIN UR APPLIANCE e Gas Properties T T SE IT SE GB GB GB Appliance intended to be installed in Butane Propane Natural gas cat II2H3 G30 G31 G20 cat IIZH3 B P Hourly rate below 28 30 mbar 37 mbar 20 mbar at 15 C under 1013 mbar HIGH SPEED BURNER Marking engraved on injector 78 78 121 Nominal heat release rate kW 2 25 2 25 2 25 Reduced heat release rate kW 0 850 0 850 Hourly rate g h 164 161 Hourly rate I h 214 SUPER FAST BURNER Marking engraved on injector 88 88 137 Nominal heat release rate kW 3 00 3 00 3 10 Reduced heat release rate kW 0 850 0 780 Hourly rate g h 218 214 Hourly rate I h 295 DOUBLE CROWN BURNER Marking engraved on injector 95 95 147 Nominal heat release rate kW 3 50 3 50 3 80 Reduced heat release rate kW 1 450 1 400 Hourly rate g h 254 250 Hourly rate I h 362 SEMI FAST BURNER Marking engraved on injector 62 62 94 Nominal heat release rate kW 1
10. fr n SAMSUNG 9964 0611 09 06 Translatp Agency TECHNICIS 800 31 42 78 www samsung com it Kontakta kundtjanst pa SAMSUNG Om du har nagra fragor eller kommentarer som har att g ra med produkter fran SAMSUNG 08 585 367 87 www samsung com se EU If you have any questions or comments relating to SAMSUNG products please contact the SAMSUNG customer care centre 0870 242 0303 www samsung com uk Brandt Appliances a simplified joint stock company with a capital of 10 000 000 euros Nanterre Trade and Companies Register no 440 302 347 GN 752 56
11. nected to a 220 240 V monophase grid via a standardised CEI 60083 electrical outlet with phase ground neutral or an all pole cut off device with a minimum distance between contact openings of 3 5 mm The plug of the electrical outlet must be accessible after installation CROSS SECTION OF CABLE 220 240 V 50 Hz HO5V2V2F T90 cable 3 conductors including one ground wire Cross section of 1 wires in mm Fuse 10A FN Warning The safety wire green yellow is connected to the appliance s ground terminal and must be connected to the ground lead of the electrical set up The fuse in your set up must be 10 amperes If the power cable is damaged it must be replaced by a cable or a special kit available from the manufacturer or its After Sales Service Department el Tip Using a gas cooking appliance results in the generation of heat and humidity in the location where it is installed Make sure that you kitchen is well ventilated keep natural ventilation orifices in your home open or install a mechanical ventilation device mechanical ventilation hood Intensive prolonged use of the appliance may require additional ventilation you can for example open a window or provide more effective ventilation by increasing the setting of the mechanical ventilation system if you have one A minimum air flow of 2 m h per kW of gas power is required Example 70 cm 5 gas burners Total power 3 1
12. ng a pencil at the place indicated Fig 02 Turn the wrench clockwise until the line appears on the other side Fig 03 Warning Exceeding this limit may damage the product Reposition the burner heads burner covers and pan supports on the hob 46 1 INSTALLING YOUR APPLIANCE e Adjust the hob connections they are located under the knobs Fig 04 Proceed one tap at a time Remove the knobs and the gaskets by pulling them up Switching from butane propane natural gas to Using a small flat head screwdriver screw in the brass burner power screws yellow all the way moving in a clockwise direction Fig 05 Replace the gaskets and the knobs paying careful attention to their direction and ensuring that the knobs are pushed in all the Way Switching from butane propane to natural gas Unscrew the brass burner power adjustment screw yellow Fig 05 using a small flat head screwdriver turn twice in a counterclockwise direction Light the burner in maximum heat mode then turn down to reduced heat mode Remove the knob again then turn the burner power screw clockwise until it reaches the lowest possible setting that does not extinguish the flame Replace the gasket and knob Make several attempts to shift from the maximum flow rate to the minimum the flame should not go out if it does unscrew the burner power screw so as to obtain good flame retention during th
13. onnection is air tight after installation with soapy water 1 INSTALLING YOUR APPLIANCE CHANGING THE GAS SUPPLY Tip QI Each time you change the gas supply Warning tick the box corresponding to the new gas Your appliance is sold pre set for level on the label found in the plastic bag natural gas Refer to the corresponding Gas The injectors required for adaptation to Connection section butane propane can be found in the plastic bag containing this guide fay fe In France this hob can also be adapted for propane air gas butane air gas The adaptation kit is supplied on request by your After Sales Service Department Each time you change the gas supply you must complete the following Adjust the gas connection Change the injectors Adjust the hob connections Crucible Injector e Adjust the gas connection refer to the Gas connection paragraph e Change the injectors proceeding as follows Remove the pan supports heads and covers from all burners Using the wrench provided unscrew the injectors located under each crucible and remove them Fig 07 Replace with the corresponding gas injectors in compliance with the positionning of the injectors and the table of gas properties at the end of this section First screw them in manually until the injector locks into place Apply the wrench to the injector as far as it will go Draw a line on the burner plate usi
14. or uneven Check the cleanliness of the burners and injectors under the burners the assembly of the burners etc Check that there is enough gas left in the tank e During cooking the knobs become hot Use small saucepans on the burners located closest to the knobs Larger saucepans should be placed on the largest burners those that are furthest from the knobs Properly place the saucepan in the centre of the burner It should not extend to the knobs 54 5 COOKING CHART e GAS COOKING GUIDE PREPARATIONS TIMES DOUBLE SUPER FAST SEMI AUXILIARY CROWN FAST FAST SOUPS Bouillons 8 10 minutes X X Home style soups x FISH Court bouillon 8 10 minutes x x Barbecue 8 10 minutes x SAUCES Hollandaise b arnaise x x B chamel aurore 10 minutes x x VEGETABLES Endives spinach x X Cooked peas 25 30 minutes X x Provengal tomatoes 15 20 minutes Xx Xx Golden brown potatoes X X Pasta x X MEAT Steak X x Blanquette Osso bucco 90 minutes x Saut ed poultry breasts 10 12 minutes x Tournedos 10 minutes X X FRYING French fries X Xx Fritters X x DESSERTS Rice pudding 25 minutes x X Fruit compote Xx X Pancakes 3 4 minutes Xx Xx Chocolate 3 4 minutes X Cr me anglaise 10 minutes X Coffee small percolator x 55 6 AFTER SALES SERVICE ELECTRONICS Kontakta kundtj nst p SAMSUNG Om du har n gra fr gor eller kommentarer som har att g ra med produkter
15. ot light Check that the gas inlet pipe is not pinched Check that the length of the gas inlet pipe is less than two meters Check that the gas inlet pipe is open If you have gas in a cylinder or tank check that it is not empty If you have just installed the hob or changed the gas cylinder hold the knob down in maximum open position until gas arrives in the burners Check that the injector is not clogged if it is unclog it with a safety pin Light your burner before placing your saucepan on it e If the hob has a gas safety when lighting the flames ignite then go out when the knob is released Press firmly down on the knobs and hold them down for a few seconds after the appearance of flames Check that the parts of the burner are correctly mounted Check that the gaskets under the knobs are not coming out of their lodging Avoid strong air currents in the room Light your burner before placing your saucepan on it e In reduced heat mode the burner goes out or the flames remain high Avoid strong air currents in the room Check that the gas type being used corresponds to the injectors installed Read about markings on the injectors in the Changing the Gas Supply chapter The cooking hobs are sold pre set for use with network gas natural gas Check that the burner power screws are properly set See the Changing the Gas Supply chapter e The flames look irregular
16. rner head OQO Injector Q Tap Q Spark plugs Q Knob Tip A This Guide to Installation and Use is valid for several models Minor differences in details and fittings may emerge between your appliance and the descriptions provided 41 E o N 1 INSTALLING YOUR APPLIANCE PROPER POSITIONING Your appliance should be built in the surface of a support cabinet that is a minimum of 3cm thick made of a material that resists heat or that is covered with such a material So as not to disturbo movement of cooking utensils there should not be to the right or left or back any obstacle within 30 cm of the hob If a horizontal divider wall is positioned under the hob it should be placed between 10 cm and 15 cm away from the top of the work top In any event do not store aerosol cans or containers under pressure in any compartment that may exist under the hob See Safety Recommendations chapter FLUSH MOUNTING Follow the diagram Fig 01 Remove the pan supports the burner covers and burner heads noting their positions Turn the hob over and carefully place it on top of the opening in the cabinet so as not to 42 APPLIANCE Width Depth Thickness For 56 cm 49 cm standard cabinet Depending on cabinet For 56 cm 48 cm recommended cabinet Depending on cabinet Total 70cm 52 2 cm 51cm dimensions above the work top Total 55 4 cm 47 4 cm 3 5 cm
17. uired settings for the hob are written on a sticker located in the plastic bag as well as on the packaging In order to easily locate the reference information for your appliance we recommend that you note these data on the After Sales Service Department and Customer Relations page This page also explains to you where to find this information on your appliance RESPECT FOR THE ENVIRONMENT RESPECT FOR THE ENVIRONMENT This appliance s packaging material is recyclable Help recycle it and protect the environment by dropping it off in the municipal receptacles provided for this purpose Your appliance also contains a great amount of recyclable material It is marked with this label to indicate the used appliances that should not be mixed with other waste This way the appliance a recycling organised by your manufacturer will be done under the best possible conditions in compliance with European Directive 2002 96 EC on Waste Electrical and Electronic Equipment Contact your town hall or your retailer for the used appliance collection points closest to your home We thank you doing your part to protect the environment 40 DESCRIPTION OF YOUR APPLIANCE DESCRIPTION OF YOUR HOB Saucepan support grid Q Burner covers Q Thermocouple Q Gasket Q Bu
18. vailable To clean the hob s enamel use a specialised product for scrubbing cream Polish it with a dry stainless steel cloth Do not allow acidic liquids such as lemon juice vinegar etc to remain in contact with the enamel To clean the hob s stainless steel use a sponge and soapy water or a Commercially available special stainless steel product Warning Never clean your appliance while it is in operation Set all the gas controls to zero Tip a It is better to clean the parts of the hob by hand rather than in the dishwasher Do not use an abrasive sponge to clean your hob Do not use steam cleaning 53 4 SPECIAL MESSAGES DIFFICULTIES During operation YOU OBSERVE THAT WHAT SHOULD YOU DO e Lighting the burners There are no sparks when you press on the button to light the burner Check the electrical connection of your appliance Check that the spark plugs are clean Check that the burners are clean and properly assembled If the hob is attached to the work top check that the mounting brackets are not deformed Check that the gaskets under the knobs are not coming out of their lodging e When you press on the button to light the burner there are sparks on all of the burners simultaneously This is normal The lighting function is centralised and controls all of the burners simultaneously e There are sparks but the burner burners does do n
Download Pdf Manuals
Related Search