Samsung MCM-A100 User Manual
Contents
1. USER S MANUAL Function Controller MCM A100 System Air Conditioner OOOOPOOEGR DB98 27317A 1 RUSSIAN EAAHNIKA DEUTSCH PORTUGU S ITALIANO FRAN AIS ESPA OL ENGLISH Safety Precautions e Before using the function controller read carefully this instructions e After reading the instructions keep this user s manuals and the installation manual in a handy and safe place If a user is changed you must hand over the manuals e Never attempt to install the air conditioning system or to move the function controller by yourself N WARNING N CAUTION Do not attempt to install or repair this function controller by yourself This function controller contains no user serviceable parts Always consult authorized service personnel for repairs When moving consult authorized service personnel for disconnection and installation of the function controller Ensure that the wall is strong enough to support the weight of the function controller Must install the function controller with rated power supply In the event of a malfunction burning smell etc immediately stop operation turn off the electrical breaker and consult authorized service personnel Do not use inflammable gases near the function controller Do not spill water into the function controller Do not operate the function controller with wet hands Do not install the function controller in a location where it will2. buttons The temperature is adjusted by 1 C 1 F The air conditioner starts removing the excess humidity The quantity of air is adjusted automatically o guo co 4 To control the direction of the air flow refer to page 15 Airing Your Room If the atmosphere in your room is stale you can air it using the FAN feature 1 If necessary press ON OFF button Result The On Off indicator on the function controller comes on The air conditioner runs in the mode selected when the unit was last used The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 Toselectthe FAN mode press the Mode button until is displayed at the top of the function controller Result The air conditioner runs in FAN mode You can change modes at any time 3 Selectthe fan speed by pressing the Fan button one or more times until the intended value is displayed T li Low Sal Medium Sail High 4 Tocontrolthedirection of the air flow refer to page 15 Adjusting the Air Flow Direction Except Duct Type Depending on the position of the indoor unit you can adjust the position of the air flow blade thus increasing the efficiency of the air conditioner 1 Press the Swing button Resul
3. each time you press V button the room number is decreased by 1 from 0 15 2 Turn the air conditioner on by pressing ON OFF button Result The On Off indicator on the function controller comes on The air conditioner runs in the mode selected when the unit was last used 3 Selectan appropriate operating mode by pressing Mode button Result The air conditioner runs in the selected mode For further details on operating modes refer to page 7 15 Selecting the Automatic Operating Mode In the Automatic mode the room temperature and the fan speed are controlled automatically 1 If necessary press ON OFF button Result The On Off indicator on the function controller comes on The air conditioner runs in the mode selected when the unit was last used The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged Stopped It will start up normally after three minutes 2 To select the AUTO mode press the Mode button until ab is displayed at the top of the function controller Result The air conditioner runs in AUTO mode You can change modes at any time 3 Toadjust the temperature press the Temperature buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C 65 F and 30 C 8
4. 6 F inclusive Result Each time you press Temperature buttons The temperature is adjusted by 1 C 1 F The air conditioner starts cooling provided that the room temperature is than the selected temperature The quantity of air is adjusted automatically Cooling Your Room You must select the COOL mode if you wish to adjust the Cooling temperature Fan speed when cooling 1 If necessary press ON OFF button Result The On Off indicator on the function controller comes on The air conditioner runs in the mode selected when the unit was last used The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged Stopped It will start up normally after three minutes 2 To select the COOL mode press the Mode button until is displayed at the top of the function controller Result The air conditioner runs in COOL mode You can change modes at any time 3 Toadjust the temperature press the Temperature buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C 65 F and 30 C 86 F inclusive Result Each time you press Temperature buttons The temperature is adjusted by 1 C 1 F The air conditioner starts cooling provided that the room temperature is higher than the selected temperature the fan will however ope
5. ator On Off amp Timer Set Cancel button On Off indicator Fan speed adjustment button Test indicator Temperature adjustment buttons Indoor unit selection button Swing button Except Duct Type Test button Filter Reset button Mode selection button Test button is for your installation specialist You must NOT press it After cleaning the air filter press the filter reset button Then the function controller will display the FILTER SIGN indicator when the time to clean the air filter Duct type air conditioner does not have function of adjusting air flow direction Therefore the function is not operated even if you press the swing button Getting Started You have just purchased a function controller and it has been installed by your installation specialist Your user s manual contains much valuable information on using your function controller Please take time to read as it will help you take full advantage of the unit s features In the main part of the document you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use three different symbols Selecting the Indoor Unit You can control a specific indoor unit from the function controller 1 Select an indoor unit you want to control by pressing button Result Each time you press lt button the room number is increased by 1 and
6. come into contact with the combustible gases machine oil sulphide gas etc Do not press buttons with a pointed thing Do not pull or bend the function controller cable excessively Do not use this function controller for other purpose Do not spray an insecticide or other combustible things on the function controller Do not clean the function controller with benzene solvents or other chemicals Do not give shock to the function controller or disassemble it by yourself Contents VIEW OF THE FUNCTION CONTROLLER GETTING START itia tees ditiis SELECTING THE INDOOR UNIT SELECTING THE AUTOMATIC OPERATING COOLING YOUR ROOM u Heatinc Your Room Excert Coona Mopts Removinc Excess HUMIDITY AIRING Your ROOM ADJUSTING THE AIR FLow Direction Excert Duct Type 10 12 14 15 View of the Function Controller The function controller is an additional controller which is used with the centralized controller Operating mode Removing frost indicator Centralized controller indicator Except Cooling Only Models Communication error indicator L G cna CE T E Temperature setting Room number display H H B kl i Number Air flow direction Filter Sign indic
7. ing provided that the room temperature is higher than the selected temperature the fan will however operate sane Mul Select the fan speed by pressing the Fan button more times until the intended value is displayed efa Automatic rotated ny a 7 eal DAP Low v bal Medium Tall High 5 Tocontrolthe direction of the air flow refer to page 15 m Removing Excess Humidity If the atmosphere in your room is very humid or damp you can remove excess humidity without lowering the room temperature too much 1 If necessary press ON OFF button Result The On Off indicator on the function controller comes on The air conditioner runs in the mode selected when the unit was last used The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 Toselectthe DRY mode press the Mode button until e is displayed at the top of the function controller Result The air conditioner runs in DRY mode You can change modes at any time 3 Toadjust the temperature press the Temperature buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C 65 F and 30 C 86 F inclusive Result Each time you press Temperature
8. rate 4 Select the fan speed by pressing the Fan button one or more times until the intended value is displayed efa Automatic rotated ny a DAP Low v bal Medium Tall High 5 Tocontrolthe direction of the air flow refer to page 15 Heating Your Room Except Cooling Only Models You can select the HEAT mode only in heat pump models You must select the HEAT mode if you wish to adjust the Heating temperature Fan speed when heating 1 If necessary press ON OFF button Result The On Off indicator on the function controller comes on The air conditioner runs in the mode selected when the unit was last used The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged Stopped It will start up normally after three minutes 2 To select the HEAT mode press the Mode button until Xf is displayed at the top of the function controller Result The air conditioner runs in HEAT mode Vou can change modes at anv time To adjust the temperature press the Temperature buttons one or more times until the required temperature is displayed Possible temperatures are between 16 C 61 F and 30 C 86 F inclusive Result Each time you press Temperature buttons The temperature is adjusted by 1 C 1 F The air conditioner starts cool
9. t blade is moving up and down 109 When the air conditioner is first turned the blade is moved 2 Tostop the blade press the Swing button again To set to the required position press the Swing button again when the blade is in the required position ELECTRONICS
Download Pdf Manuals
Related Search