Samsung LE22A451C1 User Manual
Contents
1. gt When using an HDMI DVI cable connection you must use the HDMI IN jack gt The interlace mode is not supported gt The set might operate abnormally if a non standard video format is selected gt Separate and Composite modes are supported SOG is not supported English 28 Setting up the TV with your PC gt Preset Press the SOURCE button to select PC mode Press the MENU button to display the menu Press the ENTERG button to select Picture Select the required option by pressing the A or V button then press the ENTERC button When you are satisfied with your setting press the ENTER button Press the EXIT button to exit Auto Adjustment Auto adjustment allows the PC screen of set to self adjust to the incoming PC video signal The values of fine coarse and position are adjusted automatically Easy Setting 1 Press the TOOLS button on the remote control 2 Press the A or V button to select Auto Adjustment then press the ENTER button Screen Adjustment Coarse Fine The purpose of picture quality adjustment is to remove or reduce picture noise If the noise is not removed by Fine tuning alone then adjust the frequency as best as possible coarse and Fine tune again After the noise has been reduced re adjust the picture so that it is aligned on the center of screen Press the A or V button to select Coarse or Fine then press the ENTER button Press the 4 or B button2. Press the POWER button on the remote control Start Plug 8 Play The message Start Plug amp Play is displayed with OK selected Select the appropriate language by pressing the A or V button aaa Press the ENTERG button to confirm your choice Press the 4 or B button to select Store Demo or Home Use then the ENTERC button gt We recommend setting the TV to Home Use mode for the best picture in your home environment gt Store Demo mode is only intended for use in retail environments gt If the unit is accidentally set to Store Demo mode and you want to return to Home Use Standard Press the Volume button on the TV When the volume OSD is displayed press and hold the MENU button on the TV for 5 seconds The message Check antenna input is displayed with OK selected Press the ENTERC button gt Please check that the antenna cable is connected correctly Select the appropriate country by pressing the A or V button Press the ENTERG button to confirm your choice The Auto Store menu is displayed with the Start selected Press the ENTERG button gt The channel search will start and end automatically gt After all the available channels are stored the Clock Set menu appears gt Press the ENTERG button at any time to interrupt the memorization process Press the ENTERG button Select the Month Day Year Hour or Minute by pressing the lt or B button Set
3. Medium Sets the TV to medium energy saving mode High Sets the TV to high energy saving mode Easy Setting 1 Press the TOOLS button on the remote control OS O 2 Press the A or V button to select Energy Saving Picture Mode Standard 3 Press the lt or B button to select the Off Low Santina Medium or High SRSiS Xia 4 Press the EXIT or TOOLS button to exit Dual I II 4 gt Adjust English 25 Selecting the Source You can select among external sources connected to your TV s input jacks 1 Press the MENU button to display the menu Press the A or V button to select Input then press the ENTERC button 2 Press the ENTERC button again to select Source List gt Available signal sources TV Ext AV Component PC HDMI 3 Move G Enter Return gt You can choose only those external devices that are connected to the TV 3 Select the required device by pressing the A or V button Press the ENTERG button 2 Move Enter D Return Press the SOURCE button on the remote control to toggle between all the available source TV mode can be selected by pressing the TV button number 17 low wee l buttons 0 9 and the P button on the remote control PZ taeeeee A Npa AANO AA MUTE Ca oi o You can also watch HDMI mode simply by pressing the HDMI 7T s CA button on the remote control H CHLIST Bs Can f English 26 Editing the Input Source Names Name the
4. The adjusted values are stored according to the selected a KABA AN H Move Enter 9 Return Picture mode Warm1 or Warm2 is only activated when the picture mode is Movie Size Auto Wide Wide 16 9 Wide Zoom Zoom 4 3 Just Scan You can select the picture size which best corresponds to your viewing requirements e Auto Wide Automatically adjusts the picture size to the 16 9 aspect ratio Wide Adjusts the picture size to 16 10 appropriate for DVDs or wide broadcasting 16 9 Adjusts the picture size to 16 9 appropriate for DVDs or wide broadcasting Wide Zoom Magnify the size of the picture more than 4 3 Zoom Magnifies the 16 9 wide picture in the vertical direction to fit the screen size 4 3 This is the default setting for a video movie or normal broadcasting Just Scan Use the function to see the full image without any cutoff when HDMI 720p 1080i or Component 1080i signals are input Y YY YYY Auto Wide function is available only in TV Ext and AV mode In PC Mode only Wide and 4 3 mode can be adjusted Settings can be adjusted and stored for each external device you have connected to an input of the TV Temporary image retention may occur when viewing a static image on the set for more than two hours Wide Zoom Move the screen up down using the A or V button after selecting the by pressing the gt or ENTER button Zoom Select E by pressing the 4 or B butto
5. English 16 Resetting the Picture Settings to the Factory Defaults You can return to the factory defaults picture settings 1 To select the desired picture effect follow the Changing the Picture Standard instructions number 1 to 3 on page 15 2 Press the A or V button to select Reset then press the ENTERC button 3 Pressthe A or V button to select OK or Cancel Press the ENTERC button 4 Press the EXIT button to exit gt The Reset will be set for each Picture mode English 17 Mode Backlight Contrast Brightness Sharpness Colour Picture Options Move Standard G Enter D Return Changing the Picture Options 1 Press the MENU button to display the menu OT Picture Press the ENTERC button to select Picture J Mode Standard gt Backlight eee 7 2 Press the A or V button to select Picture Options then Baa press the ENTERC button Sarpras 2 3 Select the required option by pressing the A or V button Reset gt then press the ENTER button 4 When you are satisfied with your setting press the ENTERC button 5 Press the EXIT button to exit gt Colour Tone Cool2 Cool1 Normal Warm1 Warm2 You can select the most comfortable colour tone to your eyes gt gt Move Enter 5 Return J In PC mode you can only make changes to the Colour Tone and Size from among the items in Picture Si M Options Digtal NR
6. English 7 Viewing the Menus 1 With the power on press the MENU button The main menu appears on the screen The menu s left side d E has icons Picture Sound Channel Setup Input Briness larpness an an 2 Press the A or V button to select one of the icons Tit l S Then press the ENTERG button to access the icon s sub na E OK menu 3 Press the EXIT button to exit gt The on screen menus disappear from the screen after about one minute 3 Move GEnter 5 Return Using the TOOLS Button You can use the TOOLS button to select your frequently used functions quickly and easily The Tools menu change depending on which external input mode you are viewing pound Mode 1 Press the TOOLS button SRSTSXT The Tools menu will appear Energy Saving 2 Press the A or V button to select a menu 3 Press the A lt gt ENTERG buttons to display change or use the selected items For a more detailed description of each function refer to the corresponding page Picture Mode see page 15 GC CG Sound Mode see page 21 Sleep Timer see page 23 SRS TS XT see page 21 e Energy Saving see page 25 Dual I Il see page 22 PIP see page 20 Auto Adjustment see page 29 English 8 Plug amp Play When the TV is initially powered on several basic settings PMG Ba PTAY a T proceed automatically and subsequently The following settings are available 1
7. are satisfied with your setting press the ENTERC button 5 Press the EXIT button to exit Programme Programme number to be assigned to a channel Press the A or V button until you find the correct number gt You can also select the channel number directly by pressing the numeric buttons 0 9 Colour System Auto PAL SECAM NTSC4 43 Press the A or V button to select the required colour standard Sound System BG DKI I L Press the A or V button to select the required sound standard TV TT ssa Manual Stole T olour System Auto gt Sound System BG gt Channel S6 Search 140 MHz Store or eo KAKO ig Move Enter 9 Return Channel When you know the number of the channel to be stored Press the A or V button to select C Air channel or S Cable channel Press the B button then press the A or V button to select the required number gt You can also select the channel number directly by pressing the numeric buttons 0 9 gt f there is abnormal sound or no sound re select the sound standard required Search When you do not know the channel numbers Press the A or V button to start the search The tuner scans the frequency range until the first channel or the channel that you selected is received on the screen Store When you store the channel and associated programme number Set to OK by pressing the ENTERC button gt Channel mode P Programme mode When comp
8. component connector Pr Pa Y on the rear of your set and the other ends to corresponding component video out connectors on the DVD If you wish to connect both the Set Top Box and DVD you should connect the Set Top Box to the DVD and connect the DVD to component connector Pr Ps Y on your set The Pr Ps and Y connectors on your component devices DVD are sometimes labeled Y B Y and R Y or Y Cb and Cr Connect RCA audio cables optional to R AUDIO L on the rear of your set and the other ends to corresponding audio out connectors on the DVD KENSINGTON LOCK depending on the model The Kensington lock optional is a device used to physically fix the system when used in a public place If you want to use a locking device contact the dealer where you purchased the TV The location of the kensington lock may be different depending on its model English 5 Viewing the Remote Control Television Standby button Selects the TV mode directly Number buttons for direct channel access O One Two digit channel selection Volume increase Volume decrease Temporary sound switch off Use to quickly select frequently used functions Use to see information on the current broadcast Colour buttons Use these buttons in the Channel list etc Displays the Channel List on screen Available source selection Previous channel D PG Next channel P Previous chann
9. device connected to the input jacks to make your input source selection easier 1 Press the MENU button to display the menu Press the A or V button to select Input then press the ENTERC button Press the A or V button to select Edit Name then press the ENTER button Press the A or V button to select the device that you wish to edit Press the ENTERC button Press the A or V button to select the required device Press the ENTERG button Press the EXIT button to exit English 27 aa ji Source List iTV gt Edit Name Move Enter 5 Return it Namen O AV EEE Component PC 3 HDMI 3 Move Enter 9 Return Setting up Your PC Software Based on Windows XP The Windows display settings for a typical computer are shown below The actual screens on your PC may be different depending upon your particular version of Windows and your particular video card Even if your actual screens look different the same basic set up information will apply in almost all cases If not contact your computer manufacturer or Samsung Dealer 1 First click on Control Panel on the Windows start menu 2 When the control panel window appears click on Appearance and Themes and a display dialog box will appear 3 When the control panel window appears click on Display and a display dialog box will appear 4 Navigate to the Settings tab on the display dialog box The correct size setting resol
10. may produce partial after images To prevent this effect reduce the brightness and contrast when displaying still images 2008 Samsung Electronics Co Ltd All rights reserved Contents CONNECTING AND PREPARING YOUR TV Shistof Pantset es ees AA 2 installingiiheStahdi ee 2 Installing the Wall Mount Kit 2 Viewing the Control Panel cesses 3 Viewing the Connection Panel uu Lalamunan 4 Viewing the Remote Control mma nannawana 6 Installing Batteries in the Remote Control Y AS e EN Emal O ps Placing Your Television in Standby Mode Viewing the Menus Using the TOOLS Button Plug Sipa EN TA SETTING THE CHANNELS Storing Channels Automatically 10 Storing Channels Manually eeceeeeeeeees 11 Adding Locking Channels u s na nanana 12 Sorting the Stored Channels as 1G Assigning Channels Names cen 118 Fine Tuning Channel Reception 14 SETTING THE PICTURE Changing the Picture Standard 15 Adjusting the Custom Picture 16 Resetting the Picture Settings to the FactorJDefau ts 3 AA AA Alt Changing the Picture Options cers ts Viewing the Picture In Picture PIP 20 SETTING THE SOUND Sound Features ee ee 21 Selecting the Sound Made lana nanan 22 Comnecting Headphones Sold separately 22 SETTING THE TIME Settin
11. of your TV s features 0 Press to decrease or increase the volume In the on screen menu use the am buttons as you use the 4 and B buttons on the remote control O cro Press to change channels In the on screen menu use the cip o buttons as you use the A and V buttons on the remote control Without the Remote Control you can turn on the TV by using the Channel buttons English 3 Power Press to turn the TV on and off Remote Control Sensor Aim the remote control towards this spot on the TV Power Indicator Blinks and turns off when the power is on and lights up in stand by mode Speakers Viewing the Connection Panel Power Input gt gt Whenever you connect an external device to your TV make sure that power on the unit is turned off gt When connecting an external device match the colour of the connection terminal to the cable EXT Connector g Input Output Video Audio L R RGB Video Audio L R EXT 0 0 O Only TV output is available Inputs or outputs for external devices such as VCR DVD video game device or video disc players DVI IN HDMI DVI IN Supports connections between HDMI connection enabled AV devices Set Top Boxes DVD players No additional Audio connection is needed for an HDMI to HDMI connection gt What is HDMI High Definition Multimedia interface allows the transmission of high definitio
12. select one of the picture settings Press the MENU button to display the menu Press the ENTERG button to select Picture Press the ENTERC button again to select Mode Press the A or V button to select the desired picture effect Press the ENTERC button Press the EXIT button to exit Dynamic Selects the picture for high definition in a bright room Standard Selects the picture for optimum display in a normal environment Movie Selects the picture for comfortable display in a dark room gt The Picture mode must be adjusted separately for each input source Easy Setting 1 2 3 4 Press the TOOLS button on the remote control Press the A or V button to select Picture Mode Press the 4 or B button to select the required option Press the EXIT or TOOLS button to exit English 15 Contrast Brightness Sharpness Colour o Wa Resi a1 a Mode Standard Dp Backlight 1 7 95 Picture Options et Move Enter 9 Return Backlight Contrast Brightness Sharpness Colour hee Na 4 7 Picture Options Move Enter 9 Return 28e G2 Gi any Picture Mode Sound Mode Sleep Timer SRS TS XT Energy Saving Dual I II 4 Standard gt 4 gt Adjust Adjusting the Custom Picture Your set has several settings which allow you to control GOL picture quality g Mode Standard YYYY y To select the
13. sure to distinguish between the front and back of the stand when assembling them 2 Fasten two screws at position and then fasten two screw at position gt Stand the product up and fasten the screws If you fasten the screws with the LCD TV placed down it may lean to one side gt The stand is installed for models with the screen size of 37 inch and above Installing the Wall Mount Kit the wall For detailed information on installing the wall mount see the instructions provided with the Wall Mount items Contact a technician for assistance when installing the wall mounted bracket Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the TV on your own Do not install your Wall Mount Kit while your TV is turned on It may result in personal injury due to electric shock i gt Remove the stand and cover the bottom hole with a cap and fasten with two screws English 2 Viewing the Control Panel Side Panel buttons ANNIN EJ3DANOS Ced gt SAMSUNG HiH Q i gt The product colour and shape may vary depending on the model SOURCE Toggles between all the available input sources TV Ext AV Component PC HDMI O In the on screen menu use this button as you use the ENTER button on the remote control 0 MENU Press to see an on screen menu
14. the Month Day Year Hour or Minute by pressing the A or V button gt You can also set the Month Day Year Hour and Minute by pressing the number buttons on the remote control Press the ENTERG button to confirm your setting The message Enjoy your viewing is displayed When you have finished press the ENTER button gt Even if the ENTERC button is not pressed the message will automatically disappear after several seconds Language Select your language Country Select your country Auto Store Automatically scans for and stores channels available in the local area Clock Set Sets the current time for the TV clock English 9 If you want to reset this feature 1 ey O Press the MENU button to display the menu Tanguage engin K Press the A or V button to select Setup then press the Melody ka Energy Saving Gi pa ENTERG button Press the ENTERC button again to select Plug amp Play For further details on setting up options refer to the page 9 gt The Plug amp Play feature is only available in the TV mode Move Enter 9 Return Storing Channels Automatically You can scan for the frequency ranges available to you and availability depends on your country Automatically allocated ng programme numbers may not correspond to actual or desired Manual Store gt programme numbers However you can sort numbers manually Sor
15. SERIES 4 Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care centre Country Customer Care Centre Tr Web Site AUSTRIA 0800 SAMSUNG 726 7864 www samsung com at BELGIUM 0032 0 2 201 24 18 www samsung com be 844 000 844 www samsung com cz CZECH REPUBLIC Distributor pro Ceskou republiku Samsung Zrt eska organiza n slo ka Vysko ilova 4 14000 Praha 4 DENMARK 70 70 19 70 www samsung com dk EIRE 0818 717 100 www samsung com ie FINLAND 030 6227 515 www samsung com fi FRANCE a E0 IEMA www samsung com GERMANY 01805 SAMSUNG 726 7864 0 14 Min www samsung com HUNGARY 06 80 SAMSUNG 726 7864 www samsung com ITALIA 800 SAMSUNG 726 7864 www samsung com LUXEMBURG 0035 0 2 261 03 710 www samsung com be NETHERLANDS 0900 SAMSUNG 726 7864 0 10 Min www samsung com nl NORWAY 815 56 480 www samsung com no POLAND das www samsung com pl PORTUGAL 80820 SAMSUNG 726 7864 www samsung com pt SLOVAKIA 0800 SAMSUNG 726 7864 www samsung com sk SPAIN 902 10 11 30 www samsung com SWEDEN 0771 400 200 www samsung com se SWITZERLAND 0800 SAMSUNG 726 7864 www samsung com ch U K 0845 SAMSUNG 7267864 www samsung com TURKEY 44477 11 www samsung com ESTONIA 800 7267 www samsung ee LATVIA 800 7267 www samsung conv lv LITHUANIA 8 800 77777 www samsung It KAZAH
16. STAN 8 10 800 500 55 500 www samsung kz KYRGYZSTAN 00 800 500 55 500 RUSSIA 8 800 555 55 55 www samsung ru TADJIKISTAN 8 10 800 500 55 500 UKRAINE 8 800 502 0000 www samsung com UZBEKISTAN 8 10 800 500 55 500 www samsung uz imagine the possibilities Thank you for purchasing this Samsung product To receive more complete service please register your product at www samsung com global register Model ____ Serial No BN68 01425Q 00 Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care centre See back cover for more information Precautions When Displaying a Still Image A still image may cause permanent damage to the TV screen Do not display a still image on the LCD panel for more than 2 hours as it can cause screen image retention This image retention is also known as screen burn To avoid such image retention reduce the degree of brightness and contrast of the screen when displaying a still image Watching the LCD TV in 4 3 format for a long period of time may leave traces of borders displayed on the left right and center of the screen caused by the difference of light emission on the screen Playing a DVD or a game console may cause a similar effect to the screen Damages caused by the above effect are not covered by the Warranty e Displaying still images from Video games and PC for longer than a certain period of time
17. Used to display the index contents page at any time while you are viewing teletext SAMSUNG 6 gt You can change teletext pages by pressing the numeric buttons on i the remote control i English 30 The teletext pages are organized according to six categories Part Contents Selected page number Broadcasting station identity Current page number or search status Date and time Text Status information FASTEXT information gt Teletext information is often divided between several pages displayed in sequence which can be accessed by Entering the page number Selecting a title in a list Selecting a coloured heading FASTEXT system gt Press the TV button to exit from the teletext display i TY source NMODOWS Using the Anti Theft KENSINGTON LOCK depending on the model The Kensington lock is a device used to physically fix the system when using it in a public place The appearance and locking method may differ from the illustration depending on the manufacturer Refer to the manual provided with the Kensington lock for proper use The locking device has to be purchased separately 1 Insert the locking device into the Kensington slot on the LCD TV Figure 1 and turn it in the locking direction Figure 2 2 Connect the Kensington lock cable 3 Fix the Kensington lock to a desk or a heavy
18. allows you to prevent unauthorized users such as children from watching unsuitable programmes by muting out video and audio 5 Press the A or V button to select Child Lock then press the ENTERC button 6 Select On by pressing the A or V button then press the ENTERC button 7 Press the A or V button to select Channel List then press the ENTERG button 8 Move to the Q field by pressing the A V lt or gt button select a channel to be locked and press the ENTERG button Cy Move Enter Page ka Return Add Q Lock gt If you press the ENTERG button again the V symbol next to the channel disappears and the channel lock is cancelled gt Ablue screen is displayed when Child Lock is activated 9 Press the EXIT button to exit gt Select On or Off in Child Lock to easily turn the channels which selected on Q to be active or inactive You can select these options by simply pressing the CH LIST Sie Ei button on the remote control i engg English 12 Sorting the Stored Channels This operation allows you to change the programme numbers of the stored channels This operation may be necessary after using the auto store 1 Press the MENU button to display the menu Press the A or V button to select Channel then press the ENTERG button Press the A or V button to select Sort then press the ENTERG button Select the channel number that you wish
19. and then tie the string tightly gt Install the TV near to the wall so that it does not fall backwards Wall gt Itis safe to connect the string so that the clamps fixed on the wall are equal to or lower than the clamps fixed on the TV gt Untie the string before moving the TV Verify all connections are properly secured Periodically check connections for any sign of fatigue for failure If you have any doubt about the security of your connections contact a professional installer English 32 Troubleshooting Before Contacting Service Personnel No sound or picture Normal picture but no sound Screen is black and power indicator light blinks steadily No picture or black and white picture Sound and picture interference Blurred or snowy picture distorted sound Remote control malfunctions Check signal cable message is displayed On PC mode Mode Not Supported message is displayed The damaged picture appears in the corner of the screen The Resets all settings to the default values message appears Check that the mains lead has been connected to a wall socket Check that you have pressed the button on your set Check the picture contrast and brightness settings Check the volume Check the volume Check whether the MUTEXX button has been pressed on the remote control Check if TV Speaker is on On your computer check Power Signal Cable Th
20. ark pixels on the screen These pixels will have no impact on the performance of the product English 33 Technical and Environmental Specifications Model Name LE22A454 LE22A451 Screen Size Diagonal 22 inch PC Resolution 1680 x 1050 60 Hz Sound Output 3W x 2 Dimensions WxDxH Body 558 X 67 X 404 mm With stand 558 X 216 X 453 mm Weight With stand 7 kg Environmental Considerations Operating Temperature Operating Humidity Storage Temperature Storage Humidity 10 C to 40 C 50 F to 104 F 10 to 80 non condensing 20 C to 45 C 4 F to 113 F 5 Yo to 95 Yo non condensing Stand Swivel Left Right 0 gt Design and specifications are subject to change without prior notice gt This device is a Class B digital apparatus gt For the power supply and Power Consumption refer to the label attached to the product English 34
21. desired picture effect follow the contrast Changing the Picture Standard instructions number 1 to 3 Sharpness On page 15 Tit Picture Options Press the A or V button to select a particular item Press the i ENTERC button Press the 4 or B button to decrease or increase the value of a particular item Press the ENTER button Ba Press the EXIT button to exit Backlight Adjusts the screen brightness by adjusting the LCD backlight brightness 0 10 Contrast Adjusts the lightness and darkness between objects and the background Brightness Adjusts the brightness of the whole screen Sharpness Adjusts the outline of objects to either sharpen them or make them more dull Colour Adjusts the colours making them lighter or darker Tint Adjusts the colour of objects making them more red or green for a more natural look Move Adjust D Return The adjusted values are stored according to the selected Picture mode In PC mode you can only make changes to Backlight Contrast and Brightness In TV Ext AV modes of the PAL system you cannot use the Tint Function You can return to the factory defaults picture settings by selecting the Reset Refer to Resetting the Picture Settings to the Factory Defaults on page 17 The energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced and that this will reduce the overall running cost
22. e TV is using its power management system Move the computer s mouse or press any key on the keyboard Adjust the colour settings Check that the broadcast system selected is correct Try to identify the electrical appliance that is affecting the set and move it further away Plug your set into a different mains socket Check the direction location and connections of your aerial This interference is often due to the use of an indoor aerial Replace the remote control batteries Clean the upper edge of the remote control transmission window Check the battery terminals Check that the signal cable is firmly connected to the PC or video sources Check that the PC or video sources are turned on Check the maximum resolution and the frequency of the video adaptor Compare these values with the data in the Display Modes If Just Scan is selected in some external devices the damaged picture may appear in the corner of the screen This symptom is caused by external devices not TV This appears when you press and hold the EXIT button for a while The product settings are reset to the factory defaults You may see small particles if you look closely at the edge of the bezel surrounding the TV screen This is part of the product s design and is not a defect The TFT LCD panel uses a panel consisting of sub pixels 5 292 000 which require sophisticated technology to produce However there may be few bright or d
23. een press it once again reveal Used to display the hidden text answers to quiz games for example To display normal screen press it again Colour buttons red green yellow blue If the FASTEXT system is used by a broadcasting company the different topics covered on a teletext page are colour coded and can be selected by pressing the coloured buttons Press one of them corresponding to the required The page is displayed with other coloured information that can be selected in the same way To display the previous or next page press the corresponding coloured button SAZ teletext on mix Press to activate teletext mode after selecting the channel providing the teletext service Press it twice to overlap the teletext with the current broadcasting screen Q store Used to store the teletext pages mode Press to select the teletext mode LIST FLOF If you press it in the LIST mode it switches into the List save mode In the List save mode you can save teletext page into list using the E9 store button H i sub page An Used to display the available sub page page up Used to display the next teletext page page down Used to display the previous teletext page G7 hold Used to hold the display on a given page if the selected page is linked with several secondary pages which follow on automatically To resume press it again cancel Used to display the broadcast when searching for a page index
24. el Returns to the previous menu GO Control the cursor in the menu Exit the on screen menu O Picture size selection Displays the main on screen menu Selects the HDMI mode directly Picture effect selection Teletext Functions Exit from the teletext display Teletext size selection Teletext reveal Fastext topic selection 10 Alternately select Teletext Double or Mix O Teletext store Teletext mode selection LIST FLOF Teletext sub page PG Teletext next page PO Teletext previous page Teletext hold O Teletext cancel O Teletext index gt The performance of the remote control may be affected by bright light English 6 POWER Cee e ES i 0 MENU CHLI IST P MODE TOCA Q HDMI SAMSUNG Installing Batteries in the Remote Control 1 Lift the cover at the back of the remote control upward as shown in the figure 2 Install two AAA size batteries gt Make sure to match the and ends of the batteries with the diagram inside the compartment 3 Replace the cover gt Remove the batteries and store them in a cool dry place if you won t be using the remote control for a long time gt If the remote control doesn t work check the following 1 Is the TV power on 2 Are the plus and minus ends of the batteries reversed 3 Are the batteries drained 4 Is there a power outage or is the power cord
25. elect a particular item BE PO Energy Saving 4 Press the lt or B button to select the required option 5 Press the EXIT or TOOLS button to exit e PIP On Off You can activate or deactivate the PIP function Main picture Sub picture Component TV Ext AV Position Programme HDMI TV Ext AV PC TV Ext AV Source You can select a source of the sub picture Move 4 gt Adjust D Return Position Ce 0 C 6 You can select a position of the sub picture e Programme You can select a channel of the sub picture only when the Source is set to TV English 20 Sound Features 1 Press the MENU button to display the menu Press the A or V button to select Sound then press the 3 Mode or ENTERC button EEEE 2 Select the required option by pressing the A or V button TV Speaker then press the ENTERC button 3 When you are satisfied with your setting press the ENTERC button 4 Press the EXIT button to exit S Move eres 5 Return Mode Standard Music Movie Speech Custom a 7A You can select the type of special sound effect to be used Picture Mode Standard when watching a given broadcast Sug iiz Sleep Timer Easy Setting ERs Saving 1 Press the TOOLS button on the remote control Dual I II 2 Press the A or V button to select Sound Mode 3 Press the lt or B button to select the desired sound mode 4 Press the EXIT or TOOLS b
26. function is only activated in stereo sound signal It is deactivated in mono sound signal gt This function is only available in TV mode Connecting Headphones Sold separately gt YY When you insert the head set jack into the corresponding port you can operate only Auto Volume and Sound Select in PIP mode in You can connect a set of headphones to your set if you wish to watch a TV programme without disturbing the other people in the room Sound menu Prolonged use of headphones at a high volume may damage your hearing You will not receive sound from the speakers when you connect headphones to the system The headphone volume and TV volume are adjusted differently English 22 Setting and Displaying the Current Time You can set the TV s clock so that the current time is T displayed when you press the INFO button You must also set E oie seh z the time if you wish to use the automatic On Off timers Hs Energy Savin Off 1 Press the MENU button to display the menu T Press the A or V button to select Setup then press the ENTERC button 2 Press the A or V button to select Time then press the ENTERC button Move G Enter 9 Return Press the ENTER button to select Clock Set V GS Day Year lors Press the Move to Month Day Year Hour or Min ta lt or P button v Minute on MO o Ul go aliit Sel the Month Day Year Hour avery button Co
27. g and Displaying the Current Time 23 Setting the Sleep Timer eects 23 Switching the Television On and Off Automaticall AA HA 24 A gt Symbol Press Note One Touch Button FUNCTION DESCRIPTION Choosing Your Language cccecsseeeeeeee Melody Energy Saving ou cece Selecting the Source ai Editing the Input Source Names SETTING THE PC Setting up Your PC Software Based on Windows XP uu Display Modes cece mg Setting up the TV with your PC RECOMMENDATIONS FOR USE Teletext Featuren neee ae 30 Using the Anti Theft KENSINGTON LOCK dependingjontthe mode 31 Securing the TV to the Wall naunawaan 32 Troubleshooting Before Contacting SECS RASNE oaoaraa 33 Technical and Environmental Specifications 34 English 1 List of Parts Please make sure the following items are included with your LCD TV If any items are missing contact your dealer oo Im x laggy M4XL16 Remote Control amp Batteries AAA x 2 Power Cord Cover Bottom Stand Screw X 4 Stand Cleaning Cloth Owner s Instructions Warranty card Safety Guide eRegistration Cards 5 Warranty card Safety Guide Registration Cards Not available in all locations gt The stand and stand screw may not be included depending on the model Installing the Stand 1 Connect your LCD TV and the stand gt Two or more people should carry the TV gt Make
28. hannel Manager Db ort D Kam une gt Move Enter 9 Return Move Enter 9 Return gt The following characters are available Letters of the alphabet A Z Numbers 0 9 Special characters space Repeat steps 3 to 4 for each channel to be assigned to a new name Press the EXIT button to exit English 13 Fine Tuning Channel Reception Use fine tuning to manually adjust a particular channel for Channel optimal reception GO ony United Kingdom gt 1 Use the number buttons to directly select the channel that 7 Ma aton ar i you want to fine tune ASA Ae K 2 Press the MENU button to display the menu ae Press the A or V button to select Channel then press the ENTERG button 3 ee Hila a Ak ela to select Fine Tune then press IAN 4 Press the lt or B button to adjust the fine tuning Press the ENTER button 5 Press the EXIT button to exit gt Fine tuned channels that have been saved are marked with an asterisk on the right hand side of the channel number in the channel banner And the channel number turns red gt To reset the fine tuning select Reset by pressing the A or V button and then press the ENTERC button 4y Adjust Save 9 Return English 14 Changing the Picture Standard You can select the type of picture which best corresponds to your viewing requirements 1 You can also press the P MODE button on the remote control to
29. leting tuning the broadcasting stations in your area have been assigned to position numbers from P00 to P99 You can select a channel by entering the position number in this mode C Air channel mode You can select a channel by entering the assigned number to each air broadcasting station in this mode S Cable channel mode You can select a channel by entering the assigned number for each cable channel in this mode English 11 Adding Locking Channels Using the Channel Manager you can conveniently lock or add Channel channels ts J Country United Kingdom gt Auto Store 1 Press the MENU button to display the menu eee Press the A or V button to select Channel then press the ENTERG button Name gt Fine Tune gt 2 Press the A or V button to select Channel Manager then press the ENTER button Move G Enter D Return Adding channels Using the Channel List you can add channels 3 Select Channel List by pressing the ENTERC button 4 Move to the B field by pressing the A V lt or gt button select a channel to be added and press the ENTERC button to add the channel gt If you press the ENTERG button again the V symbol next to the channel disappears and the channel is not added Z Move Enter 9 Return gt Q is active when Child Lock is selected to On a hannel List gt ild Loci OF D LAGI A amp N Locking channels This feature
30. lt Figure 2 stationary object gt The location of the KENSINGTON LOCK may be Se different depending on its model ex Figure 1 lt Optional gt CES lt Cable English 31 Securing the TV to the Wall A Caution Pulling pushing or climbing on the TV may cause the TV to fall In particular ensure your children do not hang over or destabilize the TV doing so may cause the TV to tip over causing serious injuries or death Follow all safety precautions provided on the included Safety Flyer For added stability install the anti fall device for safety purposes as follows To avoid the TV from falling 1 Put the screws into the clamps and firmly fasten them onto the wall Confirm that the screws have been firmly installed onto the wall gt You may need additional material such as an anchor depending on the type of wall a gt Since the necessary clamps screws and string are not ao gal supplied please purchase these additionally gg Wal Remove the screws from the center back of the TV put the screws into the clamps and then fasten the screws onto the TV again gt Screws may not be supplied with the product In this case please purchase the screws of the following specifications Screw Specifications Fora 17 29 Inch LCD TV M4 X 15 For a 32 40 Inch LCD TV M6 X 15 Connect the clamps fixed onto the TV and the clamps fixed onto the wall with a strong string
31. n Use the A or Wbutton to move the picture up and down After selecting E use the A or V button to magnify or reduce the picture size in the vertical direction gt After selecting Just Scan in HDMI 1080i or Component 1080i mode Select E by pressing the lt or B button Use the A V lt or gt button to move the picture Reset Press the lt or B button to select Reset then press the ENTERC button You can initialize the setting You can select these options by simply pressing the P SIZE button on the remote control i Sa Sed GH GD GD English 18 Screen Mode Wide 16 9 Wide Zoom Zoom 4 3 When setting the picture size to Auto Wide in a 16 9 wide TV you can determine the picture size you want to see the 4 3 WSS Wide Screen Service image or nothing Each individual European country requires different picture size so this function is intended for users to select it e Wide Sets the picture to 16 10 wide mode 16 9 Sets the picture to 16 9 wide mode e Wide Zoom Magnify the size of the picture more than 4 3 Zoom Magnify the size of the picture vertically on screen 64 3 Sets the picture to 4 3 normal mode gt This function is available in Auto Wide mode gt This function is not available in Component or HDMI mode Digital NR Off Low Medium High Auto If the broadcast signal received by your TV is weak you can activate the Digital Noise Red
32. n digital video data and multiple channels of digital audio The HDMI DVI terminal supports DVI connection to an extended device with the appropriate cable not supplied The difference between HDMI and DVI is that the HDMI device is smaller in size has the HDCP High Bandwidth Digital Copy Protection coding feature installed and supports multi channel digital audio DVI IN R AUDIO L DVI audio outputs for external devices gt Supported modes for HDMI DVI and Component 480i 480p 576i 576p 720p 1080i HDMI DVI 50Hz X X X 0 o 0 HDMI DVI 60Hz X 0 X X o O Component 0 0 O ie 0 0 English 4 SERVICE Connector for SERVICE only O PC IN PC AUDIO Connect to the video and audio output jack on your PC ANT IN To view television channels correctly a signal must be received by the set from one of the following sources An outdoor aerial A cable television network A satellite network Headphones jack Headphone may be connected to the headphone output on your set While the head phone is connected the sound from the built in speakers will be disabled AV IN VIDEO R AUDIO L Connect RCA cable to an appropriate external A V device such as VCR DVD or Camcorder Connect RCA audio cables to R AUDIO L on your set and the other ends to corresponding audio out connectors on the A V device COMPONENT IN Connect component video cables optional to
33. nfirm the setting ENTERC button 5 Press the EXIT button to exit bMove 3 Adjust Return gt If you disconnect the power cord you have to set the clock again gt You can also set Year Month Day Hour and Minute by pressing the number buttons on the remote control Setting the Sleep Timer You can select a time period of between 30 and 180 minutes after which the television automatically switches to standby Plug amp Play gt mode Language A ut gt Melod D 1 Press the MENU button to display the menu Energy Saving 3 bg Press the A or V button to select Setup then press the ENTERC button 2 Press the A or V button to select Time then press the ENTER button Move GeEnter 5 Return 3 Press the A or Y button to select Sleep Timer then press pasa ET ay the ENTER button a TEA 4 Press the A or V button repeatedly until the desired time Timer 1 appears Off 30 60 90 120 150 180 Timer 3 Press the ENTERC button 5 Press the EXIT button to exit gt The TV automatically switches to standby mode when the a timer reaches O Move Enter 9 Return Easy Setting 1 Press the TOOLS button on the remote control picture cee standara 2 Press the A or V button to select Sleep Timer 3 Press the lt or B button to select the minute Energy Saving 4 Press the EXIT or TOOLS button to exit bin Move 4b Adjust D Exit English 23 Switching the Television On and Off Aut
34. omatically 1 Press the MENU button to display the menu Setup Press the A or V button to select Setup then press the Plug amp Play gt ENTER button me lelody 2 Press the A or V button to select Time then press the Eneny saving ENTERC button 3 Pressthe A or V button to select Timer 1 Timer 2 Timer 3 then press the ENTER button Three different On Off Timer Settings can be made a Move Enter 9 Return gt You must set the clock first 4 Press the lt or B button to select the required item below On Time Press the A or V button to adjust to the setting satisfied On Time Select hour minute and On Off To activate CHAN timer with the setting satisfied set to On or Off Time Select hour minute and On Off To activate timer with the setting satisfied set to On L Repeat Select Once Everyday Mon Fri Mon Sat Move 4 Adjust 9 Return or Sat Sun Volume Select the desired turn on volume level You can set the hour and minute directly by pressing the number buttons on the remote control Auto Power Off When you set the timer On the TV will eventually turn off if no controls are operated for 3 hours after the TV was turned on by timer This function is only available in timer On mode and prevents overheating which may occur if a TV is on for too long time y y Choosing Your Language When you start using your set for the first time you m
35. t hah and clear any channels you do not wish to watch ine T 1 Fine Tune Press the MENU button to display the menu Press the A or V button to select Channel then press the ENTERC button Press the ENTERG button to select Country ove GiEnter 5 Return Select the appropriate country by pressing the A or V button Press the ENTERG button to confirm your choice Press the A or V button to select Auto Store then press the ENTER button Press the ENTERC button gt The TV will begin memorizing all of the available channels gt Press the ENTER button at any time to interrupt the memorization process and return to the Channel menu After all the available channels are stored the Sort menu appears refer to page 13 English 10 Storing Channels Manually You can store television channels including those received Ll aN TTT a via cable networks Rae 3 United Kingdon When storing channels manually you can choose Whether or not to store each of the channels found kana 5 The programme number of each stored channel which you wish Fine Jung 4 to identify 1 Press the MENU button to display the menu Press the A or Y button to select Channel then press the BASE HE onc ENTERC button E i 2 Press the A or V button to select Manual Store then press the ENTER button 3 Select the required option by pressing the A or V button then press the ENTERC button 4 When you
36. to adjust the screen quality Press the ENTERC button Position Adjust the PC s screen positioning if it does not fit the TV screen Press the A or V button to adjusting the Vertical Position Press the lt or B button to adjust the Horizontal Position Press the ENTERC button Image Reset You can replace all image settings with the factory default values English 29 Bi Contrast Brightness Auto Adjustment Screen Adjustment Picture Options Reset Move G Enter 9 Return e OOOO O O O F Paa NG 7T Picture Mode Sound Mode Sleep Timer SRS TS XT Energy Saving PIP Move G Enter Y Exit Position Image Reset Move Enter 9 Return Move Enter D Return Coarse Fine Ej 34 Position gt mage Reset gt Move Enter Return Teletext Feature Most television stations provide written information services via Teletext The index page of the teletext service gives you information on how to use the service In addition you can select various options to suit your requirements by using the remote control buttons gt For teletext information to be displayed correctly channel reception must be stable Otherwise information may be missing or some pages may not be displayed O exit Exit from the teletext display size Press to display the double size letters in the upper half of the screen For lower half of the screen press it again To display normal scr
37. to change by pressing the A or V button Press the ENTERG button gt The selected channel number and name are moved to right side Select the number of the programme to which the channel is to be moved by pressing the A or V button Press the ENTERG button The channel is moved to its new position and all other channels are shifted accordingly Repeat steps 3 to 5 for another channel to be sorted Press the EXIT button to exit Assigning Channels Names Channel names will be assigned automatically when channel information is broadcast These names can be changed allowing you to assign new names 1 Press the MENU button to display the menu Press the A or V button to select Channel then press the ENTERC button Press the A or V button to select Name then press the ENTERC button If necessary select the channel to be assigned to a new name by pressing the A or V button Press the ENTERG button gt The selection bar is displayed around the name box To Then Select a letter number or symbol Press the A or V button Move on the next letter Press the B button Move back the previous letter Press the 4 button Confirm the name Press the ENTERG button Country United Kingdom gt Auto Store Ng Manual Store Ng Channel Manager gt Fine Tune D Move G Enter 9 Return 3 Move eEnter 5 Return Chanel Country United Kingdom gt Auto Store Db Manual Store ng C
38. uction feature to help reduce any static and ghosting that may appear on the screen gt When the signal is weak select one of the other options until the best picture is displayed HDMI Black Level Normal Low You can select the black level on the screen to adjust the screen depth gt This function is active only when the external input connects to HDMI RGB signals English 19 Viewing the Picture In Picture PIP You can display a sub picture within the main picture of set programme or video input In this way you can watch the picture of set programme or video input from any connected equipment while watching the main picture 1 Press the MENU button to display the menu Press the A or V button to select Setup then press the Language English ENTERG button Wee NO 2 Press the A or Y button to select PIP then press the ENTERC button 3 Select the required option by pressing the A or V button then po press the ENTERC button Pa 4 When you are satisfied with your setting press the ENTER a Move Genter 9 Return button TV PIP 5 Press the EXIT button to exit p gt You may notice that the picture in the PIP window becomes O Se iea slightly unnatural when you use the main screen to view a game or karaoke Easy Setting 1 Press the TOOLS button on the remote control TEESE E 2 Press the A or V button to select PIP then press the ENTERC button HictumMode Sandara 3 Press the A or V button to s
39. unplugged 5 Is there a special fluorescent light or neon sign nearby Switching On and Off The mains lead is attached to the rear of your set 1 Plug the mains lead into an appropriate socket gt The standby indicator lights up on your set 2 Press the button on your set gt You also can press the POWER button or the TV button on the remote control to turn the TV on gt The channel that you were watching last is reselected automatically 3 Press the numeric button 0 9 or channel up down button on the remote control or lt ciR e gt button on your set gt gt When you switch the set on for the very first time you will be asked to choose language in which the menus are to be displayed 4 To switch your set off press the POWER button again Placing Your Television in Standby Mode Your set can be placed in standby mode in order to reduce the power consumption The standby mode can be useful when you wish to interrupt viewing temporarily during a meal for example 1 Press the POWERo button on the remote control gt The screen is turned off and a red standby indicator appears on your set 2 To switch your set back on simply press the POWER numeric buttons 0 9 TV button or channel up down button again gt Do not leave your set in standby mode for long periods of time when you are away on holiday for example It is best to unplug the set from the mains and aerial
40. ust select the language which will be used for displaying menus and indications 1 Press the MENU button to display the on screen menu Press the A or V button to select Setup then press the ENTERG button 2 Press the A or V button to select Language then press r the ENTER button 3 Move Enter 5 Return 3 Select a particular language by pressing the A or V button repeatedly Press the ENTERC button 4 Press the EXIT button to exit English 24 Melody Energy Saving Press the MENU button to display the menu YU Setup Press the A or V button to select Setup then press the Pua Bley ET gt ENTER button P Ting i ae is DB Energy Saving Off Select the required option by pressing the A or V button then press the ENTERG button When you are satisfied with your setting press the ENTERC button Press the EXIT button to exit Move Enter 9 Return Melody Off Low Medium High The TV power on off melody sound can be adjusted gt The Melody does not play When no sound is output from the TV because the MUTE button has been pressed When no sound is output from the TV because the Volume button has been pressed When the TV is turned off by Sleep Timer function Energy Saving Off Low Medium High This feature adjusts the screen brightness depending on the surrounding lighting conditions Off Turns off the energy saving function Low Sets the TV to low energy saving mode
41. ution Optimum 1680 X 1050 pixels If a vertical frequency option exists on your display settings dialog box the correct value is 60 or 60 Hz Otherwise just click OK and exit the dialog box Display Modes Both screen position and size will vary depending on the type of PC monitor and its resolution The resolutions in the table are recommended gt D Sub Input Mode Resolution Horizontal Vertical Pixel Clock Sync Polarity Frequency kHz Frequency Hz Frequency MHz HIV IBM 640 x 350 31 469 70 086 25 175 720 x 400 31 469 70 087 28 322 l 640 x 480 31 469 59 940 25 175 l 640 x 480 37 861 72 809 31 500 l 640 x 480 37 500 75 000 31 500 l 800 x 600 37 879 60 317 40 000 800 x 600 48 077 72 188 50 000 800 x 600 46 875 75 000 49 500 VESA 1024 x 768 48 363 60 004 65 000 1024 x 768 56 476 70 069 75 000 l 1024 x 768 60 023 75 029 78 750 1280 x 1024 63 981 60 020 108 000 1280 x 1024 79 976 75 025 135 000 1360 x 768 47 712 60 015 85 500 1680 x 1050RB 64 674 59 883 119 000 gt HDMI DVI Input Mode Resolution Horizontal Vertical Pixel Clock Sync Polarity Frequency kHz Frequency Hz Frequency MHz H V 640 x 480 31 469 59 940 25 175 l 800 x 600 37 879 60 317 40 000 VESA 1024 x 768 48 363 60 004 65 000 1280 x 1024 63 981 60 020 108 000 1360 x 768 47 712 60 015 85 500 1680 x 1050RB 64 674 59 883 119 000 H
42. utton to exit 4 gt Adjust D Exit Equalizer Balance 100Hz 300Hz 1kHz 3kHz 10kHz The sound settings can be adjusted to suit your personal preferences R gt If you make any changes to these settings the sound o o mode is automatically switched to Custom I Balance 100Hz 300Hz 1kHz 3kHz 10kHz gt Move Adjust Return SRS TS XT Off On TruSurround XT is a patented SRS technology that solves the problem of playing 5 1 multichannel content over two speakers TruSurround delivers a compelling virtual surround sound experience through any two speaker playback system including internal television speakers It is fully compatible with all multichannel formats a 7T cl i Picture Mode Standard Easy Setting coun Maas ae ae jeep limer H 1 Press the TOOLS button on the remote control SRS TS XT_ Kroi gt 2 Press the A or V button to select SRS TS XT energy Saving oim 3 Press the 4 or B button to select the Off or On 4 Press the EXIT or TOOLS button to exit 4p Adjust 9 Exit SRS C gt TruSurround XT SRS and Symbol are trademarks of SRS Labs Inc TruSurround XT technology is incorporated under license from SRS Labs Inc English 21 Auto Volume Off On Each broadcasting station has its own signal conditions and so it is not easy to adjust the volume every time the channel is changed This feature lets you automatically adjust the volume of the desired channel by lo
43. wering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low TV Speaker Off On If you want to hear the sound through separate speakers cancel the internal amplifier gt The and MUTE buttons do not operate when the TV Speaker is set to Off gt gt When TV Speaker is set to Off you can operate only Sound Select in PIP mode in Sound menu Sound Select Main Sub When the PIP feature is activated you can listen to the sound of the sub PIP picture Main Used to listen to the sound of the main picture Sub Used to listen to the sound of the sub picture Selecting the Sound Mode You can set the sound mode in the Tools menu When you set to Dual I II the current sound mode is displayed on the screen as 777 paa OOo a Picture Mode BE CT Elo Sound Mode Sleep Timer SRS TS XT Energy Saving 1 Press the TOOLS button on the remote control E 2 Press the A or V button to select Dual I II 3 Press the lt or B button to select required option 4 Press the ENTERC button Audio Type Dual 1 2 Default A2 Mono MONO Automatic oa Stereo Stereo STEREO MONO change Dual DUAL 1 DUAL 2 DUAL 1 Mono MONO Automatic NICAM Stereo MONO e STEREO change Stereo Dual MOND DAAT DUAL 1 gt If the stereo signal is weak and an automatic switching occurs then switch to the Mono gt This
Download Pdf Manuals
Related Search