Samsung SU2911 User Manual
Contents
1. on the side of the Cup If more dirt than this accumulates your cleaner will not operate effectively Note All new carpet has loose fibers which can fill the Dirt Cup quickly while vacuuming Emptying the Dirt Cup Disconnect cleaner from electrical outlet 3 1 Unlock Position Lock Position Slide the Cyclone Lever to the Unlock position Grasp handle and pull the Dirt Cup straight out to remove from Vacuum Empty dirt into garbage container Put the Dirt Cup back in the vacuum and slide the lever to the Lock position Cleaning the Pre Post motor Filter Pre Motor Filter Post Motor Cleaning The Circular Filters Grasp the Filter Cup located at the bottom of the Dirt Cup and twist counterclockwise to unlock and remove How to clean Disconnect cleaner from electrical outlet The Pre Motor Filter protects the Motor from debris It is located underneath the Dirt Cup and Filter Cup in the Center of the round part of the Cyclone Lever Remove the small round Filter and any debris on top of it Rinse well under warm water then air dry thoroughly before replacing The Post Motor Filter assists in the filtation process to return clean air to the room It is located behind the door on the front of the Cleaner When the filter becomes dirty open the door remove the filter and shake the dust off the filter Th2. Cup Problem Cleaner hard to push Possible Cause Possible Solution e Incorrect carpet height setting e Rotate nozzle control knob to lower setting Problem Poor job of dirt pickup Possible Cause Possible Solution Full or clogged Dirt Cup e Empty the Dirt Cup and check for blockages Broken or worn belt Replace belt Clogged hose or nozzle e Clean hose or nozzle area e Hole in hose Replace hose Dirt Cup improperly installed e Properly install the Dirt Cup Incorrect carpet height setting e Rotate nozzle control knob to lower setting Clogs in air flow passage e Clear clogs Problem Abnormal sound Possible Cause Possible Solution Strange sound like rushing air e Check for blockages This Vacuum cleaner is approved the following EMC Directive 89 336 EEC 92 31 EEC and 93 68 EEC Low Voltage Safety Directive 73 23 EEC and 93 68 EEC If you have any comments or questions regarding a Samsung products contact the SAMSUNG customer care center Country Customer Care Center T Web Site U K 0870 242 0303 www samsung com uk SOUTH AFRICA 0860 7267864 SAMSUNG www samsung com za DJ68 00294A REV 0 4
3. Vacuum Cleaner SU 2900 Series FOR HOUSEHOLD USE ONLY Operating Instructions IMPORTANT SAFETY INSTRUCTIONS ASSEMBLING PARTS A E E 2 ASSEMBLED VACUUM CLEANER PARTS ATTACHING THE HANDLE ip A A ooa o2 Z Z pm Spare z eed eol 7 Tamme gt Gam mm Z pan ZR ZA ZA i J ATTACHING THE HOSE AND TOOLS OPERATION n atiro ereinen aeiaai aA MAINTENANCE sssini aaia 4 TROUBLESHOOTING ssisscssticsascisistsescedussertisraanicianseical 6 Read these instructions before operating the vacuum cleaner The design and specification may be different depending on the models Register your product at www samsung com global register IMPORTANT SAFETY INSTRUCTIONS Thank you for purchasing a Samsung vacuum cleaner When using an electrical appliance basic precautions should always be followed including the following PLEASE READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WA R N N G To reduce the risk of fire electric shock or injury e Do not leave vacuum cleaner unattended when it is plugged in e Unplug from outlet when not in use and before servicing e Do not use outdoors or on wet surfaces e Do not allow children to operate vacuum cleaner or use as a toy e Close attention is necessary when used by or near children e Use only as described in this manual Use only manufacturer s recommended attachments e Do not use with damaged cord or plug e If vacuum c
4. ase Slide the extension wand and the crevice tool together into the storage clip Operation ON OFF Switch 1 To turn cleaner on press the Power switch 2 To the cleaner off press the Power switch again S Carrying handle The cleaner can also be moved by using the carrying handle Cleaning lightweight flexible rugs Stand on one end of rug and move cleaner toward other end or edge Before reaching edge push down on handle This will lift up the nozzle front of Cleanerjand will prevent rug from clinging to cleaner Continue to lift front of cleaner so that when you have reached the edge it is completely off the rug Move cleaner back to start again lower front of cleaner and use only forward strokes Handle positions The handle of your cleaner has three positions upright for storage and when using cleaning tools operating for general operation on carpet and floors low for reaching under low furniture Step on handle release pedal to lower handle 2 5 s e FJ c Q y_ option Cleaning Tool attachments Attachment tools can be used to clean furniture or drapes on stairs or in corners Transporting cleaner To move your cleaner from room to room put the handle in upright position tilt the cleaner back on its rear wheels and push forward When using the attachments ensure the vacuum c
5. ator and used belt Discard used belt With lettering on outside of belt and positioned as shown in box on D slide new belt over motor pulley B Reposition bottom plate and 4 screws Tighten screws securely Insert agitator through belt and place belt in belt guide C on agitator Should the agitator shield D become dislodged while replacing the belt or the agitator reposition it as shown noting the placement of its belt guide D When to replace the agitator brush roll When agitator brushes are worn the agitator should be replaced To check condition of brushes disconnect cleaner from electrical outlet Move the edge of a card across bottom plate while turning agitator To maintain cleaning effectiveness replace agitator if brushes do not touch card Grasp agitator firmly and fit it into position by first sliding the end opposite the belt into the rectangular slot F on side of cleaner Pull other side of agitator G into place Turn agitator making sure belt is not pinched between agitator and agitator shield How to replace Disconnect cleaner from electrical outlet Remove bottom plate belt and agitator following directions in The belt section beginning with Fig 3 10 Discard old agitator Continue following the directions in The belt section to reposition belt new agitator and bottom plate Maintenance Clearing Blockages Dis
6. connect cleaner from electrical outlet The hose on the back of the vacuum cleaner that carries the dirt from the nozzle to the Dirt Cup can sometimes become clogged If you notice a change in the sound of the vacuum motor check for blockages 3 14 Remove Dirt Cup and check Upper Tank and Louvers the Wand Check to make sure Louvers are Installed correctly To unlock the Louvers grasp the rim and turn Toward the left Pull straight down to remove If the Louvers are missing or not locked into place check and clear the tube in the center of the Dirt Cup Remove the Hose and disconnect Check for clogs in the vacuum base the wand the hose and the suction inlet If the blockage persists turn the vacuum cleaner off and unplug it Remove the bottom plate Lift up the short hose in the base of the vacuum Inspect the hose for clogs and remove any obstructions Replace the short nozzle hose and the bottom plate Troubleshooting Check this list of possible problems and solutions before bringing your vacuum to a service center Problem Cleaner won t run Possible Cause Possible Solution e Not firmly plugged in e Plug unit in firmly e No voltage in wall plug e Check fuse or breaker e Blown fuse or tripped breaker e Replace fuse or reset breaker Problem Dust escapes the Dirt Cup Possible Cause Possible Solution e Dirt Cup improperly installed e Re install the Dirt
7. e Post Motor Filter is non washable therefore do not wash it in water Replace the door by inserting the tabs on the left side and snapping the right side into place Do not operate cleaner without Either the Pre Motor Filter or Post Motor Filter in place Grasp the Circular Filters and twist to unlock Pull straight up to remove Separate the Outer foam and Inner pleated Circular Filters Wash each individually by hand in warm water Mild detergent may be used if desired Rinse well then air dry Thoroughly dry before putting them back together and replacing in the Filter Cup The Filter Cup may be washed In warm water with a mild detergent Make sure it is completely dry before reassembling with fliters The belt The belt on your cleaner causes the agitator to rotate and is important for the effective operation of the cleaner The belt is located under the bottom plate of the cleaner and should be checked from time to time to be sure it is in good condition When to replace Disconnect cleaner from electrical outlet To check belt remove bottom plate as shown in How to replace Replace belt if it is stretched cut or broken 3 9 B D Maintenance How to replace Disconnect cleaner from electrical outlet Place handle in low position and turn cleaner over so bottom side is up Remove the 4 screws as shown with a screw driver Remove agit
8. e the plug in any way e Do not modify the polarized plug to fit a non polarized outlet or extension cord e Do not touch the brush roller when it is rotating e Keep suction away from your face when using nozzles and pipe e Do not pull the power cord around sharp corners and do not allow it to become trapped e Unplug before connecting turbine nozzle only using turbine brush model SAVE THESE INSTRUCTIONS FOR FUTURE USE Assembling Parts Assembled Vacuum Cleaner Parts The assembled cleaner will look like the illustration to the left 1 Handle 2 Power switch 3 Quick release cord hook 4 Post Motor Filter 5 Crevice tool 6 Handle release 7 Carrying handle 8 Hose 9 Extension wand 10 Combination tool 11 Cyclone Lever 12 Dirt Cup 13 Filter Cup 14 Upper Tank 15 Louvers 16 Hose Wand Base 17 Height Adjustment Dial 18 Hose Clip WARNING OPERATE THE VACUUM CLEANER ONLY AT THE VOLTAGE SPECIFIED ON THE NAMEPLATE Step 1 Attaching the Handle Stand the vacuum upright and slide the base of the handle firmly into the grooves at the top of the vacuum body Insert the screw provided into the existing hole Tighten the screw securely with a screwdriver Before securing the handle please check that the handle is fitted to the vacuum body and make sure there s no gap Step 1 Attaching the Handle a Slide the end of the hose wand with tabs into the Hose Wand B
9. leaner is not working as it should or has been dropped damaged left outdoors or dropped in water take it to a service center e Do not pull or carry by cord use cord as a handle close a door on cord or pull the cord around sharp edges or corners Keep cord away from heated surface Do not unplug by pulling on the cord To unplug grasp the plug not the cord Do not handle vacuum cleaner or plug with wet hands e Do not put any object into openings Do not use with any opening blocked keep openings free of dust lint hair and anything that may reduce air flow e Keep hair loose clothing fingers and all parts of body away from openings and moving parts e Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes e Do not use without dirt cup or filters in place Empty cup and clean filter frequently when picking up very fine materials such as powder e Turn off all controls before unplugging vacuum cleaner e Use extra care when cleaning on stairs e Do not use to pick up flammable or combustible materials such as gasoline or fine wood standings or use in areas where they may be present e Store your vacuum cleaner indoors in a cool dry area e Avoid picking up hard sharp objects with the cleaner they may damage the cleaner e Always turn off this appliance before connecting or disconnecting the hose removing the bottom plate for maintenance e Use only on dry indoor surfaces never chang
10. leaner is placed firmly on the floor with the handle in the upright position Do not place the vacuum on top of furniture or steps as the brushroller may cause damage A Combination tool Two types of cleaning tools are included in one attachment rotate for desired tool Use brush side to dust furniture blinds books lamps shelves Use upholstery side for curtains draperies cushions fabrics B Crevice tool Use in comers on stairs baseboards and behind furniture C Extension Wand Use with desired attachments and narrow wand for a longer reach option Mini Turbo Brush Refer to the separated instruction Cleaning Tool attachments Carpet and rug cleaning takes place at the nozzle A When it is necessary to raise and lower the nozzle for various carpet pile heights rotate the nozzle control dial B to the desired setting For maximum cleaning performance The following carpet height settings are recommended Lowest setting for all types of carpet Higher settings for very deep pile carpet where easier pushing effort is desired while maintaining good cleaning performance Note If the cleaner is difficult to push rotate knob to the next higher setting Maintenance Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure contin ued cleaning effectiveness When to empty the Dirt Cup The dirt cup needs to be emptied when the dirt reaches the Full line
Download Pdf Manuals
Related Search