CW-3000 INDUSTRIAL CHILLER USER MANUAL - Hi-end
Contents
1. CW 3000 USER MANUAL CW 3000 INDUSTRIAL CHILLER USER MANUAL 335553353533 1 T 1 1 c 04 0200 0301 AN CW 3000 INDUSTRIAL CHILLER CW 3000 USER MANUAL lt 1 gt INTRODUCTION gt CW 3000 Series is professional cooling machine referring to international advanced thermolysis cooling system design suitable for small water cooled cooling devices requested machinery Specific disconnection alarm security protection Hermetic type water tank water is available for a long time used Real time temperature monitoring accurate knowledge of heating devices working condition Professional air cooled forced radiator with strong heat dissipating capacity and difficult to be blocked up Equipped with alarm output port to protect sensitive components quickly High cost performance low failure rate There are several options of power supply complete in specifications lt 2 gt CAUTION It is strictly forbidden to plug and run the cooler without feeding water Cooler should be placed in a well ventilated dry environment place and away from heat sources Please keep at least 30cm from obstructions to the air outlet which is in the back of the cooler and should leave at least 10cm between obstructions and air inlets of two sides The cooling water must be drained if the cooler is out of use for long time or before being transported To protect laser tubes the radiator fan of cooler will suspend t2. ct connection with the pipe outlet and inlet Blockage in circulating water pipeline Check circulating water pipeline there is water flowing but not alarming Chiller of poor EM na To improve the ventilation ventilation Ultra high temperature Reduce the heat load or to use other models A normal boot but the The water temperature A normal phenomenon Water drop in Natural drying or after adding water or To replace or repair water I Damaged pumps u changing water pumps prohibited dry transfer anhydrous boot The injection port Slow outfall drainage Open the injection port IS not open 6 PACKING LIST Machine 1pc user manual 1pc Power cord 1pc connection hose 1pc sealed hoop 2pcs Spare fuse for 250V 2A 1pc Held in the spare fuseholder of power socket An alarm signal output plug CAUTION The appliance is not to be used by children or persons with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction children being supervised not to play with the appliance Excessive heat load p NI
3. flow alarm port connects to the normally open relay and normally closed relay contacts requiring operating current to be less than 5A working voltage less than 300V Voice CW 3000 USER MANUAL i Flow sw 60C T sw Output port diagram Alarm circuit d Alarm output 4 Maintenance 1 To ensure good heat dissipating please open the lid to clean the dirt after the cooler used in long term 2 Working in cold north area it is better to use noncorrosive antifreeze fluid lt 4 gt SPECIFICATIONS Model CW 3000AG CW 3000DG CW 3000AF CW 3000DF CW 3000AK CW 3000DK Voltages AC220 240V AC100 120V AC220 240V AC100 120V AC220 240V AC100 120V Frequency 50 60Hz poe locom ea l Cooling 50W 60W Inlet and Outside dimensions Inside dimensions Inside dimensions outlet hold 10mm brass connector 8mm speedy connector 6mm speedy connector Dimensions ax2xa7em LxWet Packing 59X39X48cm LxWxH dimensions CW 3000 USER MANUAL lt 5 gt SIMPIE TROUBLESHOOTING lugged in place cord in place Machine turned on p ugg p p Replace the fuse inside the fuse burnt out power interface which is in the back of machine but unelectrified Flow alarm panel red light l Water level in with water pipe directly EE Feed water and check the connect to the outlet pipe leakage too low inlet there is no water flow When used with the device flow alarm panel red light but a dire
4. o work when water temperature is lower about 10 and it will restart to run when water temperature rises to higher about 20 C CW 3000 USER MANUAL lt 3 gt Details 1 Shape and parts name FRONT POWER SW TEMPERATURE DISPLAY SYSTEM ALARM INDICATOR EST c LOL OR RUNNING INDICATOR vXxtvVTtt ttt ti CW 3000 INDUSTRIAL CHILLER NS33333334 ERG AAA W A A A VOS U UY q 1 1 BACK NJECTION PORT ALARM SIGNAL OUTPUT TERMINAL POWER SOCKET WITH FUSE OUTLET NLET RADIATOR FAN PIII iii lt a lt a lt lt a OUTFALL CW 3000 USER MANUAL 2 The first installation It is very simple to install this industrial cooling machine The first time installation of the new machine can be carried out by following steps 1 Open the package to check if the machine is intact and all the necessary accessories are completed 2 Open the injection port then add cooling water 3 According to system conditions connect the water inlet and outlet pipe well 4 Plug in power turn on the power switch Do not allow the water overflow 5 Check the water level of the water tank again It should be 80 150cm from the surface of water to the injection port 3 Alarm description Causes of the cooling water circulation loop alarm and the working condition table Red out light H1 H2 No voice m Water stops up Pump breakdown M Note The
Download Pdf Manuals
Related Search