CT10 Barcode Scanner User Manual
Contents
1. Note Inventory function can be used under any scan mode mentioned in 1 5 16 1 3 LED Indicator The LED indicators on CT10 can help the user know about the current operation status Green LED on and off quickly Good Read with one short beep high tone Green LED on Every 5s Indicates the CT10 Scanner in Memory Mode Purple Flashing On Off ratio 1 1 Indicates the CT10 Scanner in Setting mode Blue Flashing On Off ratio 1 1 Indicates the BT is waiting for connection the CT10 stores the address of BT which connects with the last time Indicates the CT10 Scanner is out of range or can not establish connection with BT with two short beeps high low tone Blue Flashing On Off ratio Indicates the CT10 Scanner establish a BT 20ms 3s connection successfully with two short beeps low high tone Indicates the CT10 Scanner reconnect with BT with two short beeps low high tone Red Flashing On Off ratio 1 1 Indicates the CT10 Scanner has no address of BT which connects with before The default BT connect interface is HID the PIN code is 10010 17 1 4 Beeper The beeper built in CT10 can help the user know about the current operation status COS E Power on If the scanner has no BT address which could One long beep high tone connect with flashing red If the scanner has BT address which could connect with flashing blue One short beep high tone Read barcode with green LED on and2. 70 3 13 MSI Decide whether or not to enable MSI The CT10 Scanner defaults disable MSI Enable MSI Disable MSI Note Read the Disable MSI barcode will make the scanner can not read the MSI barcode Thus if the scanner can not read the MSI barcode please trying to read Enable MSI to reset For example Enable MSI 1 Read the Enter Setup barcode 2 Read the Enable MSI barcode 3 Read the Exit with Save barcode Enter Setup Exit with Save Exit without Save 71 3 14 CODE 11 Decide whether or not to enable Code 11 The CT10 Scanner defaults disable Code 11 Enable Codel1 Disable Codell Note Read the Disable Code 11 barcode will make the scanner can not read the Code 11 barcode Thus if the scanner can not read the Code 11 barcode please trying to read Enable Code 11 to reset For example Enable Code 11 1 Read the Enter Setup barcode 2 Read the Enable Code 11 barcode 3 Read the Exit with Save barcode Enter Setup Exit with Save Exit without Save T2 Chapter 4 DEFINING OUTPUT FORMAT Before data transmission to the host or device you can pre process the data and decide the format of the data transfer Contents _Toc347386307 O A A A Ho 74 Aoo oe gt ie 75 APPEND A o IA frie REX 73 4 1 CODE ID Co
3. Cancel 49 You will hear a beep if connect successfully SY 0 55K s MN Full Get 3 45PM al AA Pade ce oe nl L ae bee ek ee A CILICO Bluetooth E iput me ode Bluetooth Settints Bluetooth Auto Conne OFF Bluetooth Paired Device List Paired Device Address 00 06 52 01 03 21 Step 4 Tap Switch Input Method Step 3 Select desired Bluetooth device in the paired devices list Select Bluetooth device Step 4 Switch to Bluetooth Barcode Input method Switch Input method ast step Test Test Select Cilico Bluetooth Input method support Chinese English and Japanese the user can choose according to their requirement 50 PS oks E D E Sal AGE Select input method English US Android keyboard Cilico Chinese Bluetoot Cilico English Bluetooth Cilico Japanese Bluetox DAGA Configure input methods Step 5 Tap Finish PU ME IU E E area Ce ir ALESSIA leh 4 i g s i al i nf di 7 y Ni all ir 1 Bluetooth Barcode Input method Instructions Bluetooth device in the paired devices list select Bluetooth device Step 4 Switch to Bluetooth Barcode Input method Switch Input method Last step Test Tes Finish 51 QWERTYUIOP ASDFGHJKL 2 ZXCVBNM amp y T OSTs E iQ Pull Svar ad 2 A a 6901294086708 01494086708 I op asdfghjkl DEL 2 12 E We o mi m aa pax Td Sjaj 52 switch to English
4. barcode which will be located at the bottom of almost every page of this manual Just like reading the Enter Setup barcode the scanner will respond with three beeps tone ascending from low to high after reading the barcode Exit with Save Exit the Setting Mode without Save lf you want to exit the setting mode without saving any changes you must have the scanner read the Exit without Save barcode Just like reading the Enter Setup barcode the scanner will respond with three beeps tone ascending from low to high after reading the barcode Exit without Save Restore Factory Defaults Restore Factory Defaults is a special barcode The CT10 Barcode Scanner will respond with a short beep high tone after reading this barcode At this time the scanner system could restore factory defaults and no need to read Exit with Save barcode again The Scanner defaults enable HID PIN defaults 10010 Restore Factory Note Most of setting mode have restore factory defaults selection The factory default value for each setting is indicated by an asterisk You could use this barcode at the following status 1 The scanner can not work For example it can not read barcodes 2 You forget the settings you did to the scanner before and you don t want to be affected by the settings when you use the scanner 3 After using a function which is not be used usually in the scanner Check Software
5. Disable Codabar Note Read the Disable Codabar barcode will make the scanner can not read the Codabar barcode Thus if the scanner can not read the Codabar barcode please trying to read Enable Codabar to reset For example Enable Codabar 1 Read the Enter Setup barcode 2 Read the Enable Codabar barcode 3 Read the Exit with Save barcode Enter Setup Exit with Save Exit without Save 55 3 2 CODE 25 INDUSTRIAL25 Decide whether or not to enable Industrial 25 The CT10 Scanner defaults disable Industrial 25 Enable Industrial25 Disable Industrial25 Note Read the Disable Industrial 25 barcode will make the scanner can not read the Industrial 25 barcode Thus if the scanner can not read the Industrial 25 barcode please trying to read Enable Industrial 25 to reset For example Enable Industrial 25 1 Read the Enter Setup barcode 2 Read the Enable Industrial 25 barcode 3 Read the Exit with Save barcode Enter Setup Exit with Save Exit without Save 56 3 3 CODE 25 INTERLEAVED 25 Decide whether or not to enable Interleaved 25 The CT10 Scanner defaults disable Interleaved 25 Enable Interleaved 25 Disable Interleaved Note Read the Disable Interleaved 25 barcode will make the scanner can not read th
6. Add a device Adda printer Remove device gt Devices 2 i i Remove device CT1013122005 Category Keyboard Note CT10 default mode is HID Mode if you want to use SPP mode just read following barcodes before pairing other operations is same as HID mode 34 2 4 Connect to PDA via BT PDA is trying to connect to the CT10 Scanner BT SPP 1 Press the Power key and turn on the CT10 Scanner with correct BT settings such as setting up SPP as BT transmit interface and BT PIN code specified etc 2 Find the BT icon on PDA and double click Blueto oth ca Home da Clock amp Alarms yo op Connections Sounds amp Ka Hotifications Personal Microsoft Mw i Phone Pa System Bluetooth COM Ports lt Devices gt Mode Tap 4dd new device to search For other Bluetooth devices Tap on 4 device to modify its settings Connected Add new device 35 4 Choose CT10 click Next Bluetooth we E Select a Bluetooth Device Select a device to connect with and tap Mexk ee TI0 1230618 3 Apple Bluetooth Device 2110106105 E Coolpad 7295 5 Enter the PIN Code When setting up a BT connection if you choose The Default Value 1 input 10010 If you choose The Default Value 2 input 40510 if you specified a unique PIN code on your own input it Click Next Bluetooth a Yi E Enter Passcode Enter a passcode to establish a secure connection with CT101330
7. Turn on CT10 read the following barcodes continuously Enter Setup One click android connection Exit with Save 2 Bluetooth Pairing gt Turn on Bluetooth in your android device search CT10 in available devices and click al mi E Bluetooth US860 A o Visible to all nearby Bluetooth os AVAILABLE TOUCH TO PAIR DEVICES 011013122002 al CT1013122010 SEARCH FOR DEVICES gt It will popup Bluetooth pairing request dialog input the PIN code 10010 39 To pair with CT1013122010 Type the device s required PIN 10010 Usually 0000 or 1234 PIN contains letters or symbols You may also need to enter this PIN on the other device Cancel OK Click OK you will hear a beep from CT10 that means pairing successfully you can find paired CT10 on the android device Bluetooth U88e0 Only visible to paired devices PAIRED DEVICES gy T1013122010 E uE Connected K AVAILABLE TOUCH TO PAIR DEVICES CT1013122002 WindowsCE SEARCH FOR DEVICES 40 gt Open a textbox for example short message the CT10 can read barcodes into the textbox 8 New message 6901294086708 6901294086708 gt 0 8 v ua abc def l ghi jkl mno 0 li 41 2 4 2 One click 10S Connection 1 Turn on CT10 and read the following barcodes continuously One click iOS Connecti
8. Version lf you want to know the software version of CT10 should read the Enter Setup and Output Software Version barcode 10 Enter Setup Output Software Version Checking the software version is done at the enter setup mode so after output the software version need to read Exit without Save barcode Exit without Save Save Custom Settings 1 You may change factory defaults and customize some functions suitable for your own applications when you use CT10 you must read the Enter Setup Function barcode you want to customize Save Custom Settings Exit with Save barcodes Enter Setup Save Custom Settings Restore Customs Settings Exit with Save 2 If you want to restore to custom settings after resetting the barcode scanner just need to read Enter Setup Restore Custom Settings Exit with Save barcodes as above 11 Chapter 1 Features and Basic Setups This chapter will introduce the features and usage of the barcode scanner Contents RNR 33 Pe A OET EEE ere 13 Bee 13 OURAN _______ iii 13 LL O A 14 LL A 15 LL A 177 _ CERRI 18 Do sete o 19 I EBREO O OCRA 20 Lo A 20 LOL A 21 Ie eee nea zi nine nin zarina cirie zine nino 22 Re O cs ssesssccccscnnsseessccccsceassssssscccsecasseessscccsseaassesssscesseeassesssss 24 IO SRO ES E 25 ee eo bee o o o 25 12 1 1 Bat
9. off quickly drenante Configuration error with purple flashing eras Or transmit buffer full with green LED on and off quickly Two short beeps high tone Two short beeps low high BT connection established with blue LED flashing On Off Two short beeps high low BT connection out of range or suspended with blue LED Enter or Exit Setting mode with purple LED flashing Three short beeps tone Configuration correct with purple LED flashing A pm EP e 18 1 4 1 Beeper Volume Mute Minimum Volume Medium Volume Maximum Volume For example Set Minimum Volume for beeper 1 Read the Enter Setup barcode 2 Read the Minimum Volume barcode 3 Read the Exit with Save barcode Enter Setup Exit with Save Exit without Save 19 1 5 Scan Modes Four kinds of scan modes are supported by the CT10 Barcode Scanner 1 5 1 Manual Mode By default the scan mode is set to Manual Mode If the user keeps press the Scan Key the CT10 Scanner will emit a red light line This indicates the scanner could scan the scanning will not stop until the scanner under the following situation Read a barcode successfully Release the Scan Key Manual Mode Enter Setup Exit with Save Exit without Save 20 1 5 2 Continuous Mode When you active the Continuous Mode you don t need to trigger the Scan K
10. the scanner is set to Verify without Output Checksum Character and the scanner will check the data bases on the last character of the barcode data If the check passes the scanner will output the data without the checksum character if the check not passes the scanner will display read failure If the scanner is set to Verify with Output Checksum Character and the scanner will check the data bases on the last character of the barcode data If the check pass the scanner will output the data with the checksum character if the check not pass the scanner will display read failure Do Not Verify Verify without Output Checksum Character Verify with Output Checksum Character 61 3 6 4 STANDARD FULL ASCII CODE 39 Decide whether or not to support Code 39 Full ASCII that includes all the alphanumeric and special character The CT10 Scanner defaults full ASCII Code 39 It could disable full ASCII Code 39 via set Disable Code39 Full ASCII Enable Code39 Full ASCII Enter Setup Exit with Save Exit without Save 62 3 7 CODE 93 Decide whether or not to enable Code 93 The CT10 Scanner defaults disable Code 93 Enable Code93 Disable Code93 Note Read the Disable Code 93 barcode will make the scanner can not read the Code 93 barcode Thus if the scanner can not read the Code 93 barcode
11. 22 eee e 24 Re O 25 1 7 USB Wired Data Transmission 25 Chapici2 How o Comiectwi Bl rai nds did 26 OM 27 oE ooo ccc iii iene 27 II RI eee iene iii 27 E oe e 28 Loo 000 20 gt xe 29 Ed Connie oo Lo erre ana ne einen azz azeri einen ezezizicineeie zz nizicineeneo 35 2 4 1 One click Android Connection 39 LA E ET A 42 A a E o 45 Chapter gt SYMBOLOGY SETTINGS ld 54 _ _ SS IE 55 II o L ssseccssssssvccccccccseccccconssseessssesseccecesssneceeeasssssessssses secs 56 CRE eee IS erre ene na nie nie ni rieneereniee zen narici ce eeze nie 57 AA E e e eee ze nana zizi cin eo einen eee neziniezaziniziziozicicione 58 A O eeerttrrreeerereneeeze zena zi cinici ni rie neenenize eines zzz ze zicioione 59 _ BZ AREA 60 SE o A 60 Ce OD oe o 60 a oe el ii 61 3 6 4 STANDARD FULL ASCII CODE 39 62 jeueco ti AC 62 _ vC ERRR RATE A 63 o LL eeeeee nea neeeeeeeeneeeeezenizzzineseciveneeeneeezezeneenizizeozicecinne 64 ri 65 SEA A 65 SL E A 65 oo Cec De o ne eeieree eine nei zio eine size nizi zio izeeezeneni 66 _ BEER eee IE EEA 67 Cer ee A 67 So A 67 3 10 3 Checksum Transmission 68 ecc ETE EEE AAE RTRT 69 AL A 69 A A A 69 _ RZ OR ORA 70 eee eb cols A 70 o UI SIS o 70 O A E oO On Ore eee 71 CO sssseccsssscsveccccccssnececesssssesssssessccccccecssueceeessssseeess
12. 3 Add 0 ahead and ID is not change Do not Convert Enter Setup Exit with Save Exit without Save 65 3 9 3 Checksum Transmission Decide whether or not to transmit Checksum Transmit EAN 8 Checksum Do Not Transmit EAN 8 Checksum For example Enable EAN 8 and Convert to EAN 13 1 Read the Enter Setup barcode 2 Read the Enable EAN 8 barcode 3 Read the Convert to EAN 13 barcode 4 Read the Exit with Save barcode Enter Setup Exit with Save Exit without Save 66 3 10 EAN 13 3 10 1 Enable Disable EAN 13 Decide whether or not to read EAN 13 The CT10 Scanner defaults enable EAN 13 Enable EAN 13 Disable EAN 13 3 10 2 Convert to ISBN Decide whether or not to convert the EAN 13 to ISBN Convert EAN 13 to ISBN Do Not Convert EAN 13 to ISBN Enter Setup Exit with Save Exit without Save 67 3 10 3 Checksum Transmission Decide whether or not to include the checksum character in the data being transmitted Transmit EAN 13 Checksum Do Not Transmit EAN 13 Checksum For example Convert EAN 13 to ISBN 1 Read the Enter Setup barcode 2 Read the Convert EAN 13 to ISBN barcode 3 Read the Exit with Save barcode Enter Setup Exit with Sav
13. 5 1 Read the Enter Setup barcode 2 Read the Enable Standard 25 barcode 3 Read the Exit with Save barcode Enter Setup Exit with Save Exit without Save 59 3 6 CODE 39 3 6 1 Enable Disable Code 39 Decide whether or not to enable Code 39 The CT10 Scanner defaults disable Code 39 Enable Code 39 Disable Code 39 3 6 2 START STOP Transmission Decide whether or not to include the start stop characters in the data being transmitted Transmit Code 39 Start Stop Characters Do Not Transmit Code 39 Start Stop Characters For example Do Not Transmit Code 39 Start Stop Characters 1 Read the Enter Setup barcode 2 Read the Enable Code 39 barcode If Code 39is disabled it is need to set 3 Read the Do Not Transmit Code 39 Start Stop Characters barcode 4 Read the Exit with Save barcode Enter Setup Exit with Save Exit without Save 60 3 6 3 Checksum Verification It is not enforced to include the checksum character in the Code 39 data If checksum character is included it should be the last character of the barcode data Checksum character is a calculate value bases on all of the data and is used to check the data is correct or not Thus if the scanner is set to Do Not Verify and the scanner will output all the barcode data If
14. 6184 Press Next to continue if a passcode is mot required 6 Click Finish Click New Transmit Port in COM port 36 Bluetooth Enter Passcode Enter a passcode to establish a secure connection with CT1013306184 Press Next to continue if a passcode is mot required Device Added Your Windows phone has connected with 211013506104 Bluetooth Adda Device Select the device you wank to add 211013306182 Bluetooth er Ve 4 33 Mode COMPorts gt Devices After pairing with a device to set up a COM port tap Mew Outgoing Port For other options tap and hold an existing port New Outgoing Port x Secure Connection 37 Bluetooth Y l si H 4 36 Mode lt COM Ports gt Devices After pairing with a device to set up a COM port tap New Outgoing Port For other options tap and hold an existing port CT1013306184 COMO Mew Outgoing Port 8 Enter serial port application choose the port number you just set click open The CT10 Scanner respond with two short beeps and the indicator is flashing blue On Off ratio 20ms 3s indicating the connection between PDA and CT10 is established successfully ComTest A 43T 029171570956 029171570956 029171570956 029171570956 029171570956 029171570956 baud s600 n l6Recelve AE Button 165end Send Zone _ DigitalSend _ AT Send Timer Unicode 38 2 4 1 One click Android Connection 1
15. CT10 Barcode Scanner User Manual IMPORTANT NOTICE Safety Precaution DO NOT disassemble the scanner or place foreign matter into the scanner cause a short circuit or circuit damage DO NOT expose the scanner or battery to any flammable sources Maintenances Precaution Use a clean cloth to wipe dust off the body of the scanner If you find the scanner abnormal write down the specific scenario and consult the maintenance person Contents IMIPOR TANT IN FIC E soii ia 2 Soler SS 101 HG e O EPA Seen een CTT SOP IR ROO eT Carre ne Tn ACE NUTR ETN CC or Some Ture tree oe 2 Maintenances PIEGAUNON siria ai ia 2 CON pestello o 3 Overview orCET10 Barcode oca ida 5 Me o AA a A iii nidi iui 5 e sicilia 5 Mtoducion OF Key Ponciano 6 PEC ALI ONS E 6 CO ii MeCorec tA mina eil 7 QUICK STAR Torrain neran OR n RA toda 8 Em rine Se time Mode Ga lele 9 Exit hesena Mode WI AVC gioie collana 9 Exit the Setting Mode without SV id il 10 Restore Pacto Dedicato 10 Check Software Versi n dadas acaso 10 Sale USOS O cios 11 Chapter 1 Features and Basic Setups cocoa ncnnnnncnnnnnnononanonnnancnno 12 _ nm A AA 13 II A Cleo ee 13 o a 13 A o ANN 14 O 15 LO e e 16 _ _ _ _ _ LO el ass Arad dts lav al ln 17 ARS are eres reat ete gag aa 18 II o 19 I A 20 eee 20 Lo Copco IE oooooooooooococnonnccccccnnnnnccnccnonononanananenonaannnnnncnnncnnnnnc ninia o naniaaannss 21 eee
16. ant to add remark information you just need double click Power key quickly it will active the soft keypad If you double click Power key quickly again the soft keypad will hide It is shown as following OG ofufe fr ff fo dolo be gt E EN EE ER TPE N A N E P POE ES SI aT 44 2 4 3 Connect via BT Input Method 1 Turn on Bluetooth barcode scanner CT10 or CT20 for setup Read Enter Setup barcode Enter Setup Read Bluetooth Input Method barcode Bluetooth iui Method Read Exit with Save barcode Exit with Save 2 Setup CILICO Bluetooth barcode input method Step 1 Tap Select Input Method 45 PSP 0715 DDR Fa moses e nals Markanda l i BACOUE Instructions Step 1 Activate Bluetooth Barcode Input method Select Input method Step 2 Turn on Bluetooth palring with devices Turn on Bluetooth pairing Step 3 Select desired Bluetooth device in the paired devices list Select Bluetooth device Step 4 Switch to Bluetooth Select Cilico Bluetooth Input method support Chinese English and Japanese SY O 63K s D ll 3 38 Language amp input KEYBOARD amp INPUT METHODS Default IAE Android keyboard ry English US Cilico Chinese Bluet gt Cilico English Bluetc Cilico Japanese Blu MOAR o INPUT SETTINGS 46 Step 2 Bluetooth Pairing Turn
17. ce please refer to Chapter 2 2 Enter the Setting Mode The CT10 Barcode Scanner will III I response three beeps tone descending II from high to low and its LED indicator will flashing purple 3 Read a Setup barcode The CT10 Barcode Scanner will Enter Setup response three beeps tone ascending from low to high and its LED indicator will flashing purple For Example 4 Exit the Setting Mode The CT10 Barcode Scanner will response three beeps tone descending from high to low and its LED indicator Exit with Save Enable Codabar will not flashing purple and power off Note When any setup error occurs the CT10 Barcode Scanner will respond with a long beep low tone and its LED indicator will flashing purple Steps of Setup Enter Setup Details eg Enable Disable a Barcode Enter the Setting Mode For the scanner to enter the setting mode you must have it read the Enter Setup barcode which will be located at the bottom of almost every page of this manual The CT10 Barcode Scanner will respond with three beeps tone descending from high to low and its LED indicator becomes purple and go off quickly after reading the barcode Enter Setup For setting scanner parameters see Read a Setup Barcode below Exit the Setting Mode with Save For the scanner to exit the setting mode you must have it read the Exit with Save
18. de ID List Cr PU da _ Code 39 CAC da de Code 2of5 Standa 16 CO PORO AN Code 93 Code 128 Matrix 2 of 5 2 5 Industrial EAN 8 ISBN UPC A Decide whether or not to add Code ID in the barcode data of output Apply Output ID Ignore Output ID For example Apply Output ID 1 Read the Enter Setup barcode 2 Read the Output ID barcode 3 Read the Exit with Save barcode Enter Setup Exit with Save Exit without Save 74 4 2 Suffix Code of Barcode Settings Decide whether or not to apply Enter for suffix of barcode data Apply Enter for suffix Do not Apply Enter for suffix Decide whether or not to apply Alt to suffix of barcode data Apply Alt for suffix Do not Apply Alt for suffix For example Do not Apply Enter for suffix 1 Read the Enter Setup barcode 2 Read the Do not Apply Enter for suffix barcode 3 Read the Exit with Save barcode Enter Setup Exit with Save Exit without Save To APPENDIX The setting barcodes of parameters value 6 8 0 2 4 1 3 5 7 9 76
19. e Exit without Save 68 3 11 UPC A 3 11 1 UPC A Output 0 Decide whether or not to add 0 in the output of UPC A data UPC A Output 0 UPC A Do Not Output 0 3 11 2 UPC A Checksum Transmission Decide whether or not to include the checksum character in the data being transmitted Transmit UPC A Checksum Do Not Transmit UPC A Checksum For example UPC A Output 0 Do Not Transmit UPC A Checksum 1 Read the Enter Setup barcode 2 Read the UPC A Output 0 barcode 3 Read the Do Not Transmit UPC A Checksum barcode 4 Read the Exit with Save barcode l NA Enter Setup Exit with Save Exit without Save 69 3 12 UPC E 3 12 1 Enable Disable UPC E Decide whether or not to enable UPC E The CT10 Scanner defaults enable UPC E Enable UPC E Disable UPC E 3 12 2 UPC E Checksum Transmission Decide whether or not to include the checksum character in the data being transmitted Transmit UPC E Checksum Do Not Transmit UPC E Checksum For example Do Not Transmit UPC E Checksum 1 Read the Enter Setup barcode 2 Read the Enable UPC E barcode 3 Read the Do Not Transmit UPC E Checksum barcode 4 Read the Exit with Save barcode I HATH Enter Setup Enter with Save Enter without Save
20. e Interleaved 25 barcode Thus if the scanner can not read the Interleaved 25 barcode please trying to read Enable Interleaved 25 to reset For example Enable Interleaved 25 1 Read the Enter Setup barcode 2 Read the Enable Interleaved 25 barcode 3 Read the Exit with Save barcode Enter Setup Exit with Save Exit without Save 57 3 4 CODE 25 MATRIX 25 Decide whether or not to enable Matrix 25 The CT10 Scanner defaults disable Matrix 25 Enable Matrix 25 Disable Matrix 25 Note Read the Disable Matrix 25 barcode will make the scanner can not read the Matrix 25 barcode Thus if the scanner can not read the Matrix 25 barcode please trying to read Enable Matrix 25 to reset For example Enable Matrix 25 1 Read the Enter Setup barcode 2 Read the Enable Matrix 25 barcode 3 Read the Exit with Save barcode Enter Setup Exit with Save Exit without Save 58 3 5 CODE 25 STANDARD 25 Decide whether or not to enable Standard 25 The CT10 Scanner defaults disable Standard 25 Enable Standard 25 Disable Standard 25 Note Read the Disable Standard 25 barcode will make the scanner can not read the Standard 25 barcode Thus if the scanner can not read the Standard 25 barcode please trying to read Enable Standard 25 to reset For Example Enable Standard 2
21. e scanner under the following situation Read a barcode successfully The pre set timeout expires the default time is 2s You also can setup the best auto induction distance according to actual demand read the following barcode for setup Setup Auto induction Distance Auto induction Mode For Example 1 Read the Enter Setup barcode 2 Read the Auto induction Mode barcode 3 Read the Setup Auto induction Distance 4 Read the numeric barcode in Appendix 0 means farthest 9 means nearest 4 Read the Exit with Save barcode Then enter the Auto induction Mode Enter Setup Exit with Save Exit without Save 24 1 6 Symbologies Supported Most of the popular barcode symbologies are supported by the CT10 Scanner as listed below Refer to Chapter 4 for details of each symbology Symbologies Supported Enable Disable Prest Codabar Code 1 Code 98 MS Code 128 UCCIEAN 128 Code 39 EANIUPG Code 2 of 1 7 USB Wired Data Transmission CT10 Barcode Scanner support USB Data live transmission The user just need connect one end of the USB cable to a device with USB2 0 port and the other end to CT10 open a textbox it will enter data transmission USB wired transmission is the prior transmission mode 25 Chapter 2 How to Connect with BT 1 Make CT10 full charged press Power key If the scanner never connected with the com
22. el gt You can find a prompting at the lower right corner of your computer desktop as following After around 5 seconds you will hear a beep from CT10 and the indicator from red to blue Then connect successfully 31 Y Add a device a F Add a device This device has been successfully added to this computer Windows is now checking for drivers and will install them if necessary You may need to wait for this to finish before your device Is ready to use To verify if this device finished installing properly look for it in Devices and Printers CT1013122005 You can open a editable textbox Notepad word etc and read the barcodes File Edit Format View Help 6901 294086708 6901 294086708 6901294086708 6901 294086708 6901294086708 6901 294086708 New Text Document bct Notepad ojx i Note After pairing successfully open Bluetooth Chat then you can read the barcodes in SPP mode gt Now you click Show Bluetooth Devices you can find the CT10 in Devices and Printers 32 LA ae a eek it Peps t Le Allow a Device to connect ICA 3 Show Bluetooth Devices FS eee ee eS SS Se ris CUPET j pii Devices and Printers CT 1013122005 CT1013122005 Category Keyboard If you want to change PIN code or switch output interface you must remove the paired CT10 on the computer first 33 re Devices and Printers File Edit View Tool Help
23. etup Exit with Save Exit without Save 21 2 2 Setting up a BT connection Specify the PIN Code if you choose The Default Value 1 the passkey for setting up a BT connection is 10010 If you choose The Default Value 2 the passkey for setting up a BT connection is 40510 For security concerns the user can also specify a unique PIN code 1 Read the Enter PIN Code barcode 2 Read the setting barcodes of parameters value in APPENDIX ONE if the scanner read the setting barcodes 1 5 1 5 1 5 in order it means the PIN code is 151515 10010 40510 Default Value 1 Default Value 2 Enter PIN Code Random PIN Code Refer to APPENDIX I Note Before the CT10 Scanner connects with the other devices the user should pre set the scanner For example The CT10 Scanner is trying to connect with a host computer the setting operation is according to the following steps 1 Read the Enter Setup barcode 2 Read the Enable SPP barcode 3 Read the Default Value 1 PIN code is 10010 4 Read the Exit with Save barcode Enter Setup Exit with Save Exit without Save 28 2 3 Connect to PC via BT Steps Turn on Bluetooth of your computer take Win7 as example Note If your computer without Bluetooth you should prepare a Bluetooth Adapter Insert the adapter to USB port Turn Adap
24. ey After a successful decoding the removal of barcode is required It is not allowed to proceed to decode until the decoding delay time has passed To decode the same barcode repeatedly move away the barcode and put it back again and again for scanning Continuous Mode Set the time interval between each decoding for Continuous Mode Setup Delay between Re read Enter Setup Exit with Save Exit without Save 21 1 5 3 Auto Power Off Mode Auto Power Off Mode Setup Auto Power Off Time Enter Setup Exit with Save Exit without Save 22 Delay Between Re Read The delay time between re read of above scan modes could be set by the following barcode 400ms 00ms ls E 2s S 10s 15s 3 5s For Example 1 Read the Enter Setup barcode 2 Read the Auto Power off Mode barcode 3 Read the 1s of the time interval between each scanning barcode 4 Read the Exit with Save barcode Then enter the Auto Power Off Mode Enter Setup Exit with Save Exit without Save 23 1 5 4 Auto induction Mode Under the Auto induction Mode The users just need to move the barcodes to be scanned in front of the light band of CT10 no need press the Scan Key there will show a red light line This indicates the scanner could scan the scanning will not stop until th
25. following barcodes By default it is enabled If you don t want to upload the barcodes automatically you can setup as disabled when the Bluetooth connect the barcodes won t upload You can double click Power key to start upload the barcodes UA N UT Enable Auto Uploading Disable Auto Uploading Enter Setup Exit with Save Exit without Save 15 1 2 1 Inventory Mode lf you want to keep the barcodes in the buffer of CT10 for multiple uploading you can choose inventory mode In inventory mode CT10 will count the number of the barcodes automatically and control the time position etc for uploading Also you can clear the barcodes in the buffer after uploading Following is the setup method Read Enter Inventory Mode barcode to enter into the inventory mode Enter Inventory Mode If you want to recover to normal mode read the Enter Normal Mode barcode Enter Normal Mode 3 Read the Clear the barcodes in the buffer barcode to clear the barcodes only Suitable for inventory mode Clear the barcodes in the buffer 4 Read Data Uploading barcode to upload the barcodes in the buffer only suitable for inventory mode Data Uploading 5 Read Upload Counting barcode to count the number of the barcodes only suitable for inventory mode Upload Counting
26. input method Toas D Taia 6901294086 r08 6901294086708 28 QWERTYUIOP ASDFGHJIKL ZXCVBNM amp 6901294086708 6901294086708 P altos e Ly Tiz sa o 53 Chapter 3 SYMBOLOGY SETTINGS In this chapter a brief on the symbology setting is provided for your reference Contents A _ Snail caste emcee nc f _ _allbelleel ala 55 SL kr A 56 oo Os Le nL o 000ooooccccccnononnncnonononenanosoorrcccnnnonononononononanincsosooss 57 o a A 58 O O A 59 _ RR ERRE 60 ooo bros bose e A 60 CE o A 60 O80 CSCS OO ___ _ ee 61 II IIS MIMO cccoooooocccconnonoococococcccnn nono e eee 62 i lei eee 63 ER ae E E ERA 64 eSceu ug A tl e E hs pe IE i RT 65 OI E nie nz eni zi cine eienenizzz eine ezine inizio nie ecionene 65 SI O nea zine einen ezine cirie nine nio nice rieeineenin 65 Ci II er 66 ne e AA AAA 67 II II IS lt RERERERERARkRk gt A5S5 E E ISsblblb b bl z5 gt gt n o gZZgyg 67 SO A 67 OS One IIS ee eecrreeire nen einen iene nine cere einie nani zionize zione 68 n ae lalla oe 69 AL A 69 NUI a o ooc00cocoronorocsorccnonononnossrcononcananacorrccnonanass 69 E i 70 II IO A 70 A Se SI ooooccccoooronoroosoroncononannosorrncoonananacocrconononnno 70 PERE ae saa nae AAA AAA 71 _ _ O II lla 72 54 3 1 CODABAR Decide whether or not to enable Codabar The CT10 Scanner defaults disable Codabar Enable Codabar
27. ode Capability Codabar Code 11 Code 93 MSI Code 128 UCC EAN 128 Code 39 EAN 8 EAN 13 UPC A ISBN Industrial 25 Interleaved 25 Tsun Matix Resolution Smil Scan mode Auto off mode Manual mode Print Contrast Minimum 30 Scan angles Roll 30 Pitch 75 Yaw65 Cylinder Horizontal Scan Diameter 35mm Beeper LED 10m Visual range Indication Radio Range POWER Voltage DC SV Accord with national level two laser safety standards CE amp FCC DOC Compliance Laser Safety es lt O standby Current Operating current USER ENVIRONMENT Operating Temp 0 to 50 C 32 to 122 F 0 to 50 C 32 to 122 F 20 85 non condensing Storage Temp Operating Humidity Storage Humidity 20 85 non condensing Drop Specifications Free fall of 1 5m air drop Accessories Lithium battery Charger Data lines Correct Aiming Incorrect Aiming x IK gt C QUICK START The setting of the CT10 Barcode Scanner can be changed by reading the setup barcodes contained in this manual This section describes the procedure of setting the CT10 Barcode Scanner by reading the setup barcodes and provides some example for demonstration Steps Action Feedback if Successful l Turn on CT10 Barcode Scanner It will response with a long beep high tone its LED shows red and with Intmt twinkle Note How the CT10 Barcode Scanner establishes a connection with computer or other compatible devi
28. on Enter Setup Exit with Save 2 Bluetooth Pairing gt Turn on Bluetooth in your ios device search CT10 in available devices and click Settings hal Airplane Mode iat WiFi P Bluatooth ki Personal Hotspot Lad VPN Do Not Disturb iJ Notifications lol General bi Sounds eg Brightness A Wallpaper ij Picture Frame 0 Privacy C5 Coud _ Mail Contacts Calendars mm Notes E Reminders LA Messages FaceTime 1 Maps Bluetooth Bluetooth EN Devices CT1013121001 Not Connected amp LINDA 7 Not Connected i Nokia BH 503 Not Connected Ed Not Paired ZTE NBBDE Moi Paired 42 gt It will popup Bluetooth pairing request dialog and show the PIN code gt Find above mentioned numbers in following barcodes read them continuously and then read Exit without Save barcode Exit without Save gt You will hear a beep from CT10 if connect successfully and it will show in the paired devices on iOS device 43 matings ES uva he Mode Em y Wi Fi on Miustoolii on q i E Bluetooth Devices gt a Cellular Data Airplane Mode CT1013121001 Not Connected Ky Personal Hotspot On Li VPN or DNB417 Not Connected ni Nokia BH 503 Hot Connected 9 do Not Disturb ore ZTE Not Paired 3 Active or Hide the Input Method During the scanning you may use the soft keypad if you w
29. on Bluetooth por L A 1 t Xiaomi Phone Only visible to paired devices PAIRED DEVICES Nokia C7 00 i UL vivo S6 It t Xiaomi Phone Only visible to paired devices PAIRED DEVICES NokiaC7 00 Lu vivo S6 Eo AVAILABLE TOUCH TO PAIR DEVICES LL CT1013122005 CT1013122002 CT1013122004 2 ee AL ey pra SEARCH FOR DEVICES ER rors 47 Click for pairing and input the PIN code in following window then click OK O GGRS ih PRE ll m 3 43 i Bluetooth pairing request To pair with CT1013122005 Type the device s required PIN iil Usually 0000 or 1234 PIN contains letters ar symbols You may also need to enter this PIN on the other device Cancel OK Xiaomi Phone Only visible to paired devices PAIRED DEVICES Nokia C7 00 vivo S6 O AVAILABLE TOUCH TO PAIR DEVICES CT1013122002 11013122004 48 Step 3 Tap Select Bluetooth device ESA OB6K s E gt 2 Full i aliztooth e Input method LOM elits Step 3 Select desired Bluetooth device in the paired devices list Select Bluetooth device Step 4 Switch to Bluetooth Barcode Input method Switch Input method Last step Test Click CT10 CT20 in Bluetooth Paired Device List it will connect automatically Bluetooth Paired Device List vivo S6 46 13 F3 56 9 1 EB CT1013122005 00 06 52 01 03 21 Nokia C7 00 ICILA D9 2D 5A 6D
30. please trying to read Enable Code 93 to reset For Example Enable Code 93 1 Read the Enter Setup barcode 2 Read the Enable Code 93 barcode 3 Read the Exit with Save barcode Enter Setup Exit with Save Exit without Save 63 3 8 Code 128 Decide whether or not to enable Code 128 The CT10 Scanner defaults enable Code 128 Enable Code128 Disable Code 128 Note Read the Disable Code 128 barcode will make the scanner can not read the Code 128 barcode Thus if the scanner can not read the Code 128 barcode please trying to read Enable Code 128 to reset For Example Disable Code 128 1 Read the Enter Setup barcode 2 Read the Disable Code 128 barcode 3 Read the Exit with Save barcode Enter Setup Exit with Save Exit without Save 64 3 9 EAN 8 3 9 1 Enable Disable EAN 8 Decide whether or not to enable EAN 8 The CT10 Scanner defaults enable EAN 8 Enable EAN 8 Disable EAN 8 3 9 2 Convert to EAN 13 There is two ways for EAN 8 to change convert to EAN 13 or add 0 ahead of EAN 8 and the EAN 8 ID is not change Decide whether or not to convert to EAN 13 if EAN 8 convert to EAN 13 it will be read as same as EAN 13 If add a 0 ahead of EAN 8 and the EAN 8 ID is not change the output ID is still EAN 8 ID Convert to EAN 1
31. puter before it will responds with a beep and flashing red 2 Have the scanner read the Enter Setup barcode to enter the setting mode 3 Have the scanner read the associated barcode to activate the BT connection interface 4 Have the scanner read the barcodes for related settings 5 Have the scanner read the barcode to exit the setting mode 6 The CT10 Scanner will stay active for 1 minute waiting for a connection request from the host SPP or trying to connect to the host HID Contents A Boe eo oe ee 27 O re nea zia zi zine ceci r eee neri zizi zenzzinizioeecicinie 27 212 210 00 E 27 2 eine O NA 28 Lo o A 29 La oc A 35 ei One click Android connection s 0csscccsseesseessscccctccassesssscceseeessressssccseuereasseessss 39 o OIM oooooooosoosccocconononaosrronnonononnossrrononnnnnnossrrcnronananesoss 42 A II e iii 45 26 2 1 Select Output Interface Either SPP or HID can be chosen depending on the need 2 1 1 BT SPP Mode lf you select the output interface of BT SPP you may run HyperTerminal exe or serial port tool to collect the scanned data Enable SPP You can setup SPP data batch upload or single upload according to your requirements E AAA SPP Data Batch Upload SPP Data Single Upload 2 1 2 BT HID Mode By default BT HID is activated on the CT10 Scanner and the keyboard type is set to PCAT US Enable HID Enter S
32. s a data buffer and sends the collected data to the host computer one by one via the Bluetooth Upon reading a barcode successfully the scanner responds with one short beep and its LED indicator becomes green and goes off quickly However the host computer may not receive the data immediately if getting out of range With the 16KB transmit buffer the scanner can ignore the transmission status and keep on reading barcodes until the buffer is full When the buffer is full the scanner will respond with a long beep low tone this reminds the user that the space of buffer is not enough and can not read barcode any more Once the Buffer is full the user should return to the range of BT connection quickly the data in the buffer can be sent back to the host computer and release the space of buffer Note The 16KB transmit buffer on the scanner can hold as many as 1300 barcodes bases on Code128 You can choose to clear the data in the buffer every time when you turn on the scanner Enable Clear Data in Buffer When Disable Clear Data in Buffer When Turn On the Scanner Turn On the Scanner Note You can clear the data in the buffer via enable barcode you can also clear the data in the buffer via press the Power key long time After the Bluetooth connect successfully the barcodes in the buffer will upload to appointed position automatically You also can setup upload the barcodes in the buffer or not via read the
33. ssssscccccessueeeeeesssssesessses secs 72 Chapter 4 DEFINING OUTPUT FORMAT ll ll 73 con 74 ooon o 75 APPRENBDXRE Gi leale 76 Overview of CT10 Barcode Scanner Features of the Scanner Small size portable Supports three scan modes including Continuous Mode Manual Mode Auto off Mode Supports most popular barcode symbologies User feedback via LED indicator and beeper The voice volume of scan barcode successfully could change via setting barcode Built in 128 KB Flash memory can store up to thousand scan barcodes Provides 2 KB memory for reserve buffer while Bluetooth connection interrupt can store up to 110 scan barcodes Supports BT SPP Supports BT HID Programmable parameters include data output format editing format symbologies etc Abundant decoding symbologies Xx Whole body shockproof and drop resistance design Proprietary intellectual property rights Comfortable operating feel Button life up to 3 million times Support BT standard protocol no need adaptor X 1000mAh large capacity lithium battery Long working hours Appearance Power Scan Key y Bluetooth Wireless mode USB Wired mode Introduction of Key Function Note Long press Scan button 3 seconds will turn on the CT10 scanner Long press Scan button 3 seconds will turn off the CT10 scanner Flip the Scan button can read the barcodes Specifications Weight Dec
34. ter On ap midi ALI Adda Device Allow a Device to E m ees It will search for the devices show the following window W Add a device i A da Searching for devices Make sure your device is discoverable 29 gt The computer will search Bluetooth devices automatically A few seconds later you will find CT10 in the available devices list click Next Y Add a device x o Lo IP Add a device Select a device to add to this computer Windows will continue to look for new devices and display them here CT1013122005 si Bluetooth me Keyboard gt Select Enter the device s pairing code and click Next Y Add a device x f i Le Add a device Select a pairing option gt Create a pairing code for me The device has a keypad P Enter the device s pairing code CT1013122005 The device comes with a pairing code Check for one on the device or in the device manual Pair without using a code This type of device such as a mouse does not require a secure connection ext Cancel gt Input the pairing code 10010 and click Next 30 W Add a device x P Add a device Enter the pairing code for the device This will verify that you are connecting to the correct device The code is either displayed on your device or in the information that came with the device What if I can t find the device pairing code Next Canc
35. tery The scanner is powered by 1500mAh chargeable Lithium batteries The batteries can support the scanner work continuous for 60 hours or read 56000 barcodes read an EAN 13 barcode per 5s 1 1 1 Mounting the battery charging 1 Hold the scanner face down in one hand 2 Insert USB cable for charging 1 1 2 How to operate CT10 Barcode Scanner Turn on the scanner Press the Power key for about 2 seconds The scanner will respond with a long beep high tone and its LED indicator is flashing Turn off the scanner Press the Power key for about 3 seconds The scanner will respond with two short beeps high tone and the LED indicator is turn off 13 1 1 3 Auto Power Off In order to conserve battery power the user can specify the time interval for the scanner to automatically turn off By default it is set to 10 minutes Enter Auto Power Off Smin 10min 20min 30min Exit Auto Power Off For example Set 20 minutes for the scanner to automatically turn off 1 Read the Enter Setup barcode 2 Read the Enter Auto Power Off barcode 3 Read the 20min barcode 4 Read the Exit with Save barcode Note If you want to keep the scanner power on all the time read Exit Auto Power Off in stead of step 3 and 4 Enter Setup Exit with Save Exit without Save 14 1 2 Transmit Buffer During the Bluetooth connection the CT10 Scanner uses a 16KB memory a
Download Pdf Manuals
Related Search