User Manual Protector A601
Contents
1. RPC Manual de Utilizare Protector A601 AVR 1000 VA Multumim pentru ca ati achizitionat produsele RPC Va rugam cititi manualul de utilizare inainte de a pune in functiune acest produs 1 INTRODUCERE Instructiuni de siguranta ATENTIE e AVR ul contine materiale sub tensiune care pot fi periculoase Toate reparatiile trebuie efectuate de personal calificat Folosirea AVR ului in siguranta depinde de atentia utilizatorului Va rugam respectati urmatoarele instructiuni de siguranta e Nudezasamblati AVR ul e Nu incercati sa porniti AVR ul de la alta sursa decat de la priza standard acceptata e Nu pozitionati AVR ul langa sursa de apa sau intr un spatiu cu umiditate excesiva e Nuturnatilichide sau alte substante in AVR Nu pozitionati AVR ul direct la soare sau langa surse care emit caldura excesiva AVR ul trebuie instalat langa echipamentele cu care este folosit ca sa fie usor accesibil Pentru a deconecta AVR ul de la reteau electrica scoate ti cablul de alimentare din priza RPC 2 INSTALAREA SI FUNCTIONAREA 1 Verificarea dupa transport 3 Descrierea panoului Verificati ambalajul sa nu fie deteriorat Daca ambalajul este A Buton de pornire reset deteriorat anuntati imediat firma care s a ocupat de transport B Indicator LED C Prize de curent D Conector RJ11 2 Instalarea E Cablu de alimentare e Conectati cablul de alimentare la o priza cu impamantare e Conectati ca2. blul de alimentare al echipamentelor electronice la prizele AVR ului Porniti echipamentele e PornitiAVR ul apasand butonul de pornire pe modul ON Continutul pachetului e AVR e Manual de utilizare contine CE amp RoHS 3 PROBLEME Diagrama ar trebui sa acopere aproape toate problemele ce pot aparea in conditii normale de folosire In cazul in care AVR ul nu functioneaza corect verificati urmatorul tabel inainte sa sunti la service PROBLEME CAUZE POSIBLE SOLUTII Butonul de pornire nu este in modul ON Apasati butonul de pornire pe modul ON AVR ul nu este pornit Cablu de alimentare defect nu este conectat Verificati daca cablul de alimentare corect la priza este corect conectat la priza Indicator LED nu este aprins Alegeti o priza care functioneaza in Priza este fara curent sau este defecta parametrii corecti Tensiunea este taiata sau AVR ul AVR ul este in suprasarcina Reduceti din sarcinile consumatoare reporneste singur P de tensiune User Manual Protector A601 AVR 1000 VA Thank you for purchasing RPC products Please read user manual before putting in function this product 1 INTRODUCTION Safety instruction CAUTION e The AVR contains voltages that are potentially hazardous All repairs should be performed by qualified service personnel e The output receptacles may be dangerous even when the AVR is not connected to an AC supply The safe and continuous
3. ition Should the AVR fail to operate properly please proceed the following before calling for service PROBLEM POSSIBLE CAUSE ACTION TO TAKE Power switch doesn t turn on AVR is not on Turn on the power switch AC plug connection failed Connect the AC plug correctly LED indicator is not lighted on AC socket without power or power failure Choose the socket with electric power The power is cut off when you are using or non existence or autorestarted Overtoad connection Reduce the connect loads
4. operation and use of the AVR depends entirely on the care taken by user Please observe the following precautions e Do not disassemble the AVR e Do not attempt to power the AVR from any receptacle except a 2 pole 3 wire grounding receptacle Do not place the AVR near water or in environment of excessive humidity Do not allow liquid or any foreign object to get inside the AVR Do not place the AVR under direct sunshine or close to heat emitting source The power socket should be installed near the equipment and be easily accessible To isolate from AC input disconnect the plug from AC outlet 2 INSTALLATION AND OPERATION RPC 2 INSTALLATION AND OPERATION 1 Unpacking and Inspection Examine the packing carton for damage Notify the carrier immediately if any damage occurs La Installation Connect the power cord to a verified grounded 3 wire receptacle e Connectthe power cord of your electronic equipment to the outlets of the AVR Switch on the equipment e Switch on the AVR by pressing the main switch The LED will light on The AVR is now considered to be working properly 3 Panel Explanation A Power Reset switch B LED indicator C Output socket D RJ11 E AC input cable Package Contents e AR User Manual CE amp RoHS included TROUBLESHOOTING The Troubleshooting chart covers most of the difficulties that you may encounter under normal working cond
Download Pdf Manuals
Related Search