HV2 - User manual v6_5 A
Contents
1. HIGH VIBRATION V2 User Manual Orange LED indicates end LCD display of program and device in standby mode Recharging Vibration V2 Finished Program J List Start List Program Your Body Your Friend On Off Recharge 5VDC for battery recharging Bracelet connectors Description High Vibration v2 0 is a wellness device that can enhance the wellbeing of the user The device is powered from an internal rechargeable battery supplies the device for at least 20h following full recharge Recharging the battery is performed by attaching the stabilized 5V DC wall mount power supply provided with the HV2 device to be plugged into the 220V mains While recharging the bracelet connectors are automatically disconnected internally and the device does not provide any output signal Bracelets and DC power supply other than the ones provided shall not be used In order to replace the bracelets or the DC power supply the manufacturer shall be contacted Size 17 x 8 5 x 3 5 cm Approximate weight 300g The HV2 implements several programs having shortcuts as follows Base B Detoxification D Reconstruction Free Life L Neural 1 N1 Neural 2 N2 Fit F Kidney Holistic T OM1 O1 OM2 02 MA2 MA2 Harmony H Harmony Plus M Buzzer Z Note Buzzer is not properly a program it just transmits a brief audible warning Selecting it by pressing List appends2. Select the desired program by pressing the buttons Program or Program 7 Running successively a list of two or more programs can be performed automatically To do this select the first desired program and enter it on the list by pressing the button List Continue by selecting the subsequent program by pressing Program or Program and then by pressing List The current list is displayed on the LCD If an erroneous entry was performed the last entry on the list can be deleted by pressing List The procedure is continued until all desired programs are entered If needed for intensive treatments the same program can be entered on the list for several times 8 Press the Start button The program or the list of programs starts and the time until completion is displayed 9 Upon ending the Program end message is displayed together with the updated battery voltage As a variant the battery charging status in is displayed 10 A few seconds following the end the device enters a power saving stand by mode and the orange status LED is turned on 11 The device can be stopped by pressing the K1 in the middle position Off In order to get the desired results please allow the program s to end until the message Program end is displayed or the orange LED turns on Charging the rechargeable battery Upon switching the device on the LCD displays the battery voltage As mentioned before a voltage close to the higher
3. ge near 3 43V to the full voltage of 4 2V or from nearly 0 to 100 takes a very short time this also means that the battery lifetime has ended and the battery needs to be replaced For battery replacement please contact the manufacturer Warning The power supply should not be connected to the device during treatment The device perceives the external voltage at the charging connector and to avoid accidents automatically disconnects the bracelets Consequently in this case the device does not provide any signal to the bracelets
4. it to the list of all programs that were entered on the list Procedure for use 1 Attach bracelets at the base of the wrists about where the watch is worn Connect bracelet cables to the bracelet connectors B1 and B2 of the device 2 Push the K1 switch in the left position On the LCD displays the message HV2 ver xx x according to the version of the device The battery voltage is also displayed it can range between 3 43V and 4 23V A voltage close to the higher limit indicates that the battery is charged close to the lower limit the battery is nearly discharged and its recharging can be necessary As a variant the charging status in can be explicitly shown 3 The device automatically tests that the bracelets are connected to the user In case the body resistance is not perceived the device stops with an error message Bracelet error If this happens please attach the bracelets and restart the device If the message persists the electrical contact along the circuit is lost and the bracelets or the bracelet cords need replacement 4 Other tests are also performed automatically If any error message other than Bracelet error is issued please turn the device off and then on again If the error message persists please contact the manufacturer for a repair 5 After all tests are performed the LCD displays the message Base If this does no happen please turn the device off and then on again 6
5. limit indicates that the battery is charged close to the lower limit the battery is nearly discharged and its recharging can be necessary The device is typically used for a list of programs Most of the times for a given user the list is the same for several weeks We recommend that when the list is first entered to write down the battery indication in V or before and after running the list The difference between the two values indicates how much of the battery voltage or charge in is taken by the given treatment This tells how much above the minimum voltage of 3 43V or 0 is needed to have a subsequent completed or whether the battery should be recharged prior the next treatment A rule of thumb is simply to recharge when the battery voltage drops below 3 5 3 6V or correspondingly below 10 20 The recharging procedure is the following 1 Press the K1 switch on the Right position Recharge 2 Plug the power supply into the 220V mains and its 5V jack into the M1 connector the LCD lights up and displays Charging indicating that charging takes place If the LCD does not light up please check the contact between the jack and the M1 connector 3 If instead of displaying Charging the LCD displays Modify switch please check the K1 switch which probably is not in the Recharge position Please first press K1 in the Recharge position then unplug and re plug the power supply jack The LCD message sho
6. uld become Charging 4 While recharging the LCD also displays Battery and its voltage without being necessarily lit The relative place of the voltage within the 3 43V 4 2V range is an indication of the charging status and can provide an idea about the remaining time until charging is complete In variant the charging status can be displayed in The fact that charging takes place can be checked in two ways even if unlit the display indicates Charging and Battery as described above upon pressing any button the LCD lights up for a few seconds and displays as above It should be noted that charging needs not to be complete up to a full 4 2V or 100 if needed charging can be interrupted unplug the 5V jack from the M1 connector and press the K1 switch in the Off position 5 Following a number of hours when the battery is fully recharged the LCD lights up again and displays End charging Upon getting this message we recommend that the charger be unplugged and the K1 switch pressed in the center position Off Note however that the battery isn t harmed if the device stays in the End of charging mode 6 If after a sufficient number of hours the charging doesn t finish and the battery voltage gets stabilized at a value less than 4 2V corresponding to less than 100 this means that the battery lifetime has ended and the battery needs to be replaced Similarly if charging from a low volta
Download Pdf Manuals
Related Search