Installation Manual - Quality
Contents
1. Index Installation ENVIOMG los u 20e ee ee ne ee en Osos 03 Before Starting 222222 ooo L L L LLL LLL L22222 04 TOO A 04 Assembly InstructionsS____ __ 2 22 III eee 05 Final Instructions _ _ 2 22 eenennnnnnen 11 02 Installation Enviroment Dear technician This manual has been developed to guiding as proper installation for Quality dental unit aiming to standardize the process of installation making it easier and ensure customer Satisfaction Before installing the equipment when possible please check the installation environment place where the equipment will be installed available spaces placement of furniture patient s movement area work position of the professional s and assistant s to ensure the best placement and performance of the equipment granting a comfortable working environment not only for professionals but also for patients Make sure the necessary supplies are available for the proper functioning of the equipment Compressed Air The dental compressor must be oil free with dynamic pressure between 5 5 and 7 0 bar 80 100 psi minimum displacement of 1501 min and 30 liters reservoir Please recommend the use of coalescing filter in the equipment s air inlet Plumbing Up to 10 meters use hose 1 4 From 10 to 20 meters use hose 95 16 Use Specific woven hose for compressed air For longer stretches it is recommended project of distributi2. and move it up into the arm Fix the Operating Light 11mm L wrench to fix the chair to the ground Replace finishing covers 08 Assembly Instructions P46 44 Remove carefully all remaining packaging 45 Remove the front plactic cover of the pantograph 46 Place Junction Box over all connections and using a philips screwdriver pass the hoses through the connector detail 1 Saliva Ejector Drain 2 Saliva Ejector Air 3 Air Inlet 4 Cup Filler Drain 5 Cuspidor Drain 6 Water Inlet 7 Vacuum Pump Drain D 8 Vacuum Pump Wires 8 Opcional item 47 Identify each hose and connections All hoses are identified by labels The 48 Install the Sewer Connector 1 the water connector 2 and vacuum availability of the hoses will change according to the equipment configuration pump drain connector 3 Use proper sealing tape or similar 49 Conect the hose 90 Conect the hose from 51 Conect the hose from air 52 Conect the venturi saliva 53 Conect the hose from fromcuspidor drain cup filler drain to the venturi saliva ejector ejector set to Sewer Saliva Ejector drain Connector 04 Install water inlet hose 09 Install air inlet hose 56 Conect the vacuum pump drain hose and wires 57 Install the electrical wires This is an optional item as indicated 09 Assembly Instructions Note the water limit Tig LY P59 nun 58 Check all the connections to avoid leakages 59 Fill in the water tank with filt
3. Flat Blade Screw Philips Screwdriver Blunt Scissors 7 Concret drill 12mm Extension Cord 10m Cleaning Cloth a driver 3 16 x 4 3 16 x 4 AS N L Wrench A 2 Combination 11 x 11mm Wrenchs 13mm A Magnetic Level Hex Wrench y TA SU Samad Simin Adjustable Wrench Hammer Drill 4 04 Assembly Instructions 1 Place the box next to the installation site Use the existent handles for 2 Cut the three green tapes with cutting pliers Pull up housing cover transportation 3 Remove the protective plastic with blunt 4 Stool Upholstery P04 1 and Stool Structure P04 3 which is scissors and carefully removing from the P04 2 chair the following items m 6 Chair armrests and 7 Arm of Operation Light which is tied at 8 Junction Box 9 Water tank and Chair 10 Move up the working headrest the three indicated points Anchorage Kit table from the chair seat 11 Remove the front plastic cover of the pantograph 12 Remove the finishing covers and keep them 13 Remove the chair fixing screws using L Wrench using philips screwdriver 11mm 05 Assembly Instructions 14 Remove the chair from wooden base 15 Release the seat fixing handle screw 16 Remove the seat upholstery watching the screw to avoid damages detail 17 Release the handle screw and remove the seat 18 Release the four screws for the rear pantograph 19 Remove the rear pantograp
4. Instructions Able Professional Operation This equipment must be operated by professional who have the ability to work on dental procedures Storage Before the first operation or after long stop periods weekends holidays vacations the user must eliminate all air and water stuck inside the hoses shut off the water cocks depressurize and empty the water tank turn the general switch and the general circuit breaker off For reactivation of the unit verify the functioning of the entire set before starting operation Direct exposure to Sunlight The equipment must not be exposed directly to solar light to prevent from the plastic covers and or the upholstery to wear out precociously Environmental awareness The organic residues the contaminated materials and disposable items must be properly eliminated according to the rules of the local law Daily Cares Replace the bottle water Clean the unit as perinstructions on the Owner s Manual for Quality Equipment Shut the water and compressed air valves and turn the circuit breaker off after work Check the compressor before start using the dental set Drain the humidity filter of the compressor before starting using the dental set Equipment properly installed well oriented user well satisfied customer 11 MOlsen The Brand of Innovation OLSEN IND STRIA E COM RCIO S A Av Ivo Lucchi 68 Distrito Industrial Palho a Santa Catarina Brasil Caixa Post
5. al 59 CEP 88133 510 Fone Fax 55 48 2106 6000 www olsen odo br OLSEN SHOW ROOM PREMIER Filial Olsen Rua Rep blica do Iraque 1369 Campo Belo CEP 04611 002 Fone Fax 55 11 3539 3944 5402102 Rev 00 Seguranca so Compulsorio INMETRO REGISTRO DE PRODUTOS PARA A SAUDE Ko B i a BOAS PR TICAS DE FABRICA AO RDC 185 Certifica o FDA 10042326
6. ered water remove 60 Fit the stool seat over stool structure Seat then close Junction Box using plastic rivets protection plastic from water tank filter Install the yourself on the stool and check the e check its up water tank by turning it counterclockwise and down adjustment 61 Check if all items of equipment have been properly installed make sure all are functioning properly such as the controls of the chair and pneumatic devices Remove all leftover packages remaining before presenting the installed equipment to the customer 10 Final Instructions After finishing the installation check operation of all instruments chair movements switches and Operating Light Double check all air water connections to ensure there is no leakage After checking all the equipment operations instruct the user about its correct managing Check all handpieces to be used in the equipment and pressure compatibility If necessary make duly adjustments Show to the customer each main valve air inlet water for spittoon bowl and cup filler Also explain about zero and working positions how to record working positions as well as correct managing of Operating Light Explain about the water replacement using filtered drinking water the correct way to install and remove water tank as well as its water level Fill in the warranty form with the customer guiding him on each item Give him the owner s manual and instruct aboutits reading General
7. fore starting the equipment installation please check the following items 1 Installation site Check the doors width to ensure the equipment s box will get in otherwise you must to unpack the equipment before 2 Power supply Check if electrical power is available at dental office Check also voltage and where circuit breaker s box is located 3 Compressed Air Make sure the compressor is installed and working properly Check plumbing conditions If necessary proceed drainage cleaning to avoid water and debris into the equipment Check filters conditions If there is no filter ask the customer to install it Check the main compressed air block valve If there is no block valve install it inside the Junction Box 4 Water Network Check water supply and its pressure If water pressure is not enough we do recommend to install water pressurizer system Make sure there is water block valve available If there is no water block valve install it inside the Junction Box 5 Hydro sanitary electrical and compressed air sketches Check the exactly location of each abovementioned plumbing to avoid accidents when using the drilling machine 6 Chair fixation point Inform the customer about necessity of chair anchorage Position the chair according the dental office layout Tools Necessary tools to intall the equipment Y Universal Plier with Cutting Plier with Snap Rings electrical insulation electrical insulation Plier L
8. h cover and keep the lower covering cover using flat screwdriver four screws Cristal cable for voltage selection Factory Standard 220V A 20 Before plug in the equipment please check the network voltage and proceed necessary changes at transformer and fuse Plug in the equipment P20 1 and turn it on Firstly releasing the emergency button P20 2 and after by pressing the On Off Switch detail 21 Raise the seat up to its maximum height 22 Release the counter nuts above indicated using two 13mm wrenches Thread up the top nut touching the metal plate Remove the lower nut from the screw and keep it 06 E23 23 Unscrew the holder nuts using 13mm wrench and remove the Delivery Unit from the holder 26 Put the Working Table at working position and fix magnetic level on the post of Operating Light 29 Adjust the right level and tighten the nuts on the delivery unit metal bracket using two 13mm wrenches Air Clamp Air inlet Connector The availability of items will change according to the equipment s configuration 32 Check if all above items are available Assembly Instructions C21 25 Take the two nuts from the holder P23 and use it to fix the Delivery Unit to the chair Do not tighten screws now 24 Couple the Delivery Unit to the chair watc
9. hing the right insertion of the screws and Delivery Unit s metal bracket detail P27E P28 28 Turn the magnetic level to adjust the delivery unit perpendicular level to the chair 27 Adjust Delivery Unit level parallel to the chair and tighten the nuts as indicated above using two 13mm wrenches q i J 31 Unpack the water unit unroll the hoses and place the instruments on its right holders couple the syringe tip 07 Assembly Instructions 35 Install the seat lower covering watching the holder on the chair frame Tighten the handle screw 36 Fix the rear pantograph cover tightening the four screws watching sizes and right places to insert them detail P37 1 Pe 37Replace the seat upholstery on the chair watching the specific fit 1 and watching the screw 2 to avoid 38 Raise up the backrest frame and remove the damaging the chair s PC Board Tighten the handle screw 3 finishing cover 39 Remove the screws from the backrest using a 5mm Hex Wrench place backrest on its frame and handtighten the center screw Tighten screws carefully to avoid upholstery damages Replace finishing cover H b 41 Fix armrests on the chair using 13mm wrench and 42 Plug in the Operating Light electrical connector 43 After install the anchors on the ground use place the finishing covers using 3mm Hex Wrench
10. on with specific rigid pipe Water to Spittoon Bowl and Cup filler Install an easy access block valve to stop water supply to the equipment at the end of working day and also to limit water pressure if necessary The water pressure must to be between 2 8 and 6 0 BAR and ideal pH between 6 5 and 8 If the water pressure is not enough we recommend consulting an experienced professional for hydraulic systems We also recommend to use a filter in the equipment s water inlet Sewage System The sewage pipe must have good hydraulic declivity and should preferably be installed underground Use 940 mm pipe Power Supply Single phase installation proper grounding and provided with an exclusive circuit breaker If the electricity network has tension variations we do recommend power stabilizer Vacuum Pump Sewage System Connecting Junction Box to the Vacuum pump installation use curved pipes Don t use 90 fittings to avoid debris deposits and decreasing suction power Fixing chair to the ground For safety reasons both for the professional and patient we recommend to fix the equipment on the ground with anchor bolt screws provided with the equipment Fixation is strong recommended to prevent shifting of the equipment and consequently disruption of electrical hydraulic and pneumatic connections Damages caused to the equipment for not fixing the same are entire responsibility of the technician and the owner 03 Before Starting Be
Download Pdf Manuals
Related Search