Home

GEPON OLT OT-2000S CLI User Manual

1. Command epon slot3 olt1 ext mgmt show Grammar Function Show OLT s UDP management function information Example 1 Show the current OLT s UDP management information epon slot3 olt1 ext mgmt show Olt Extern Network Management Configurations admin enable host ip address 192 168 120 1 host udp port 14115 olt management udp port 14115 4 3 4 6 Link Management Mode Command epon slot3 olt1 link lt linkid gt Grammar Function Enter LINK management mode and configure link Parameter lt linkid gt Designated linked with value range from 1 to 256 Example 1 Show the current online LINK epon slot3 olt1 link Following is online link list Link Id Mac Address Online Status 1 00 a1 02 0a a1 08 Online 2 Enter Link1 management interface 25 oN OVERIEK GEPON OLT CLI User Manual epon slot3 olt1 link 1 epon slot3 olt1 link1 epon slot3 olt1 link1 input or help to show command directory no block block link dynamic mac clear clear dynamic mac table dynamic mac list show all dynamic mac table dynamic mac refresh refresh dynamic mac table rediscover force link rediscovery show show link basic configuration sla set link SLA parameters static mac add add a static mac static mac del delete a static mac static mac list show all static mac table 4 3 4 6 1 Block Current Link Command epon slot3 olt1 link1
2. Command e pon sys console speed lt speed gt Grammar Function Set OLT system s console port speed Value range bps2400 bps115200 lt speed gt Remark value should be 2400 2 n n is integer 4 3 12 4 ONU Authorization Management Mode Command epon sys onu auth Grammar Function Enter onu authorization management mode Example 1 enter onu authorization management mode epon sys onu auth epon sys onuauth epon sys onuauth input or help to show directory inv onu process invalid ONU list list configure ONU address range type set authentication type 70 ILN OVERIEK GEPON OLT CLI User Manual 4 3 12 4 1 Illegal ONU List Operation 4 3 12 4 1 1 Clear Illegal ONU List Command i epon sys onuauth inv onu clear Grammar Clear current illegal ONU list then the illegal onu can get a new Function chance to be authorized under OLT 4 3 12 4 1 2 Show Illegal ONU List Command epon sys onuauth inv onu show Grammar Function Show illegal ONU list and list all illegal ONU s MAC address 4 3 12 4 2 Configure ONU Authorized Address List 4 3 12 4 2 1 Add ONU Authorized Address List Command i epon sys onuauth Hlist add start end type Grammar Function Add an ONU address list and appoint its authorization type start ONU starting MAC address such as 00 A1 02 02 01 BO end ONU ending MAC address suc
3. Command epon slot3 olt1 onu1 fe1 attribute duplex duplex Grammar Function Configure ONU port s duplex status duplex ONU port s duplex status with value half or full 4 3 4 7 6 1 5 Configure ONU Port Flow Control Function Command epon slot3 olt1 onu1 fe1 attribute flow ctrl oper Grammar Function Configure ONU port s flow control function Enable disable ONU port flow control function oper Enable enable ONU port flow control function Disable disable ONU port flow control function 4 3 4 7 6 2 Configure ONU port s Bridge Parameter 4 3 4 7 6 2 1 Show ONU Port Bridge Parameter Command pon slot3 olt1 onu1 fe1 bridge Grammar Function Show ONU port bridge Parameter example 1 Show ONU port 1 s bridge Parameter epon slot3 olt1 onu1 fe1 bridge ONU 3 1 1 Port fe1 bridge parameter automatic learning entry limit 16 learned entry age limit 0 forwarding mode 802 1d mode 4 3 4 7 6 2 2 Configure ONU Port s Dynamic MAC Limits Command epon slot3 olt1 onu1 fe1 bridge lt entry limit gt 37 oN OVERIEK GEPON OLT CLI User Manual Grammar Function Configure ONU port s dynamic learning MAC number lt entry limit gt Maximum learning MAC number with valid value from O to 64 0 means not to learn MAC address 4 3 4 7 6 2 3 Configure ONU Port s MAC Aging Time Comma
4. Command clear Grammar Function Clear screen 4 5 4 Copy File Command e copy lt scr file gt lt dest file gt Grammar Copy file Function When lt dest file gt is ignored lt scr file gt s contents is printed on the screen lt scr file gt Source file lt dest file gt destined file 4 5 5 Show System s Date Command date Grammar Function Show system s current date and time 4 5 6 Delete File Command del filename Grammar Function Delete appointed file filename Appoint deleted file name 86 1N OVERIEK GEPON OLT CLI User Manual 4 5 7 Exit From The Current Command Mode Command exit Grammar Exit from the current command mode and return to the previous Function command mode 4 5 8 Return to System Main Directory Command end Grammar Function Return to the system s main directory 4 5 9 Help Command help Grammar Function Command help 4 5 10 Command History Command history Grammar Function Show current input command history 4 5 11 Log Out System Command logout Grammar 87 ZN OVERIEK Function Log out systemo 4 5 12 Show Current File List Command i Grammar Function Show current directory s file list 4 5 13 PING Command ping lt host gt Grammar Fu
5. port list Port list Appoint deleted mirror sour s data flow direction T ingress direction egress both 4 3 2 4 Add Mirror Source VLAN Command epon mirror source add vlan vlanid Grammar Configure added mirror source VLAN All the packet in the VLAN Function domain will arrive the designated mirror port Mirror source doesn t support data flow in the direction of VLAN domain Designate the VLAN as mirror source with the value range from1to lt vlanid gt 1064 17 ILEN OVERIEK GEPON OLT CLI User Manual 4 3 2 5 Delete Mirror Source VLAN Command i epon mirror source delete vlan lt vlanid Grammar Function Configure deleting mirror source VLAN i Appoint the deleted mirror source VLAN with value range from 1 to lt vlanid gt 408A 4 3 2 6 Clear Mirror Source Command epon mirror source clear Grammar Function Clear all mirror source including all source port and source VLAN 4 3 3 Network Configuration Mode Command epon network Grammar Function Configure inband and outband management port s IP address Example 1 Enter network management mode epon network epon net epon net input or help to show the following directory no address set network interface address no gateway configure network default gateway 18 1N OVERIEK GEPON OLT CLI User Manual 4 3 3 1 Configur
6. 4 3 2 1 Mirror Destination Port EE 16 4 3 2 2 Add Mirror Source Port enne nnne nnne nnne nnne 16 4 3 2 3 Delete Mirror Source Port 17 4 3 2 4 Add Mirror Source VLAN enne ennt nnne enne nennen 17 4 3 2 5 Delete Mirror Source VAN 18 4 3 2 6 Clear Mirror Source 18 4 3 3 Network Configuration Mode nennen nennen nennen nnne 18 4 3 3 1 Configure Management Port s IP and Sub Mack 19 4 3 3 2 Configure NMS Port Gateway nnne nnne enne 19 4 3 4 OLT Management Mode 20 4 3 4 1 Enter OLT Management Mode 20 4 3 4 2 Enable OLT iiiter t terr eren er e RR YER EENEG 21 4 3 4 3 OLT Bridge Configuration enne enne 21 4 3 4 4 Restore PON Default Setting rrrrrnrrrronnrvrrnnnnrrrrnnnnvvrrnnnnvnrnrnnnvnrannnvnnrennn 23 4 3 4 5 External UDP Management Function essere 23 4 3 4 6 Link Management Mode esses enne eene nennen nennen 25 4 3 4 7 ONU Management Mode neret enne enne nnne 31 1N OVERIEK GEPON OLT CLI User Manual 4 3 4 8 Configure Link ID Overwrite Function rrrrnnnvrrnnnnvvnrnnnnvvnrnnnnvnrnnnnnvnrnnnn 48 4 3 4 9 Configure ONU ID Overwrite Functlon nnn 48 4 3 4 10 Reboot PON Card 48 4 3 4 11 Save PON card configuration ccccccccssccsssssceesssseecessseecsssseeeessseeeees 48 4 3 4 12 Show OLT s Basic Information sese 49 4 3 5 Configure Enable Password Management eese 49 4 3 6 Protocol VLAN Configuration Mode sess 50 4 3 6 1 Add Brotocol eene enne nennen etes tents
7. Command epon show task Grammar Function Show system s current task information 4 4 4 Enable CATV RF Function Current Unotrade has developed and produced a wide range of ONU models such as only data ONU FD101H FD111H FD112H FD104H FD104B FD108B and ONU of various service function such as FD304H 4FE RF FD204H 4FE 2POTS_ FD404H 4FE 2POTS RF So far our EMS and CLI NMS could both support data and RF cutoff function in our EMS or in our CLI management interface As for VOIP function we could only support CLI management on the console port of the ONU Command epon slot3 olt2 onu9 catv enable Grammar Function Enable ONU s RF function 84 1N OVERIEK GEPON OLT CLI User Manual 4 4 5 disable CATV RF Cut Off Function Command epon slot3 olt2 onu9 catv disable Grammar i Disable ONU s RF function if subscriber don t pay CATV cost on time Function from the OLT management interface 4 5 Global Command Global command can be used under any command mode 4 5 1 Create Command Alias Command alias alias cmd Grammar Function Create appointed commande alias alias Input command s alias cmd Original command 4 5 2 Change Directory Command cd directory Grammar Function Enter appointed directory directory Input directory 85 1N OVERIEK GEPON OLT CLI User Manual 4 5 3 Clear Screen
8. 14 1N OVERIEK GEPON OLT CLI User Manual 4 3 Enable Mode Command epon gt enable Grammar Function Enter enable management mode and provides enable password Example 1 enter enable management mode epon gt enable password epon The password to enter enable mode is blank defaultly epon Input or help to show the follwing directory mirror mirroring configuration network configure network parameters olt enter olt config mode passwd change enable password prot vlan enter protocol based vlan config mode rate ctrl set switch port ingress rate limit global parameters rstp enter rapid spanning tree config mode show dislpay configuration swmode set basic switch mode swport enter switch port config mode system configure system basic parameters trunk enter trunk config mode user User configuration vian enter vlan config mode 4 3 1 Switch Control Card MAC Address Management 4 3 1 1 Configure Switch Control Card s MAC Aging Time Command epon mac address aging timeout Grammar 15 1N OVERIEK GEPON OLT CLI User Manual Function Configure switch control card s MAC address aging time MAC aging time with value range from 10 to 630 seconds sten timeout length is 10 seconds 4 3 1 2 Show Switch Control Card s MAC Address List Command epon mac address show port Grammar Bice Show switch co
9. 32 ZN OVERIEK 4 3 4 7 2 2 Add IGMP Address and Port List Command epon slot3 olt1 onu1 igmp add ipaddr lt portlist gt Grammar Function Add a IGMP address and a port number ipaddr Input IGMP address such as 224 0 0 1 lt portlist gt Input port number with valid value range from fe1 to fe8 4 3 4 7 2 3 Delete IGMP Address Command i e epon slot3 olt1 onu1 igmp delete lt ipaddr gt Grammar Function Delete IGMP address lt ipaddr gt Input IGMP address such as 224 0 0 1 4 3 4 7 2 4 The Last Member Enquiry Times Command pon slot3 olt1 onu1 igmp Imqc value Grammar Function Set the last member enquiry times value value range from 0 to 12 4 3 4 7 2 5 Re Delivery Times Command i pon slot3 olt1 onu1 igmp rc lt value gt Grammar Function Set IGMP packet s re delivery times lt value gt Value range from 0 to 12 4 3 4 7 2 6 Show Current IGMP Configuration Information Command Grammar epon slot3 olt1 onu1 igmp show 33 GEPON OLT CLI User Manual 1N OVERIEK GEPON OLT CLI User Manual Function Show current IGMP information 4 3 4 7 3 Configure ONU User Information Command epon slot3 olt1 onu1 info info Grammar i Configure ONU user information Function Just input info to show the current ONU user s information info User information byte
10. Configure the appointed gateway address 4 3 4 OLT Management Mode 4 3 4 1 Enter OLT Management Mode Command eponttolt lt slotid gt lt oltid gt Grammar Sancti Enter OLT management mode to configure OLT downplink and ONU unction just input olt could show the current online OLT lt slotid gt olt pon card slot with value marked from 1 to 4 oltid Pon ID with valid value 1 and 2 Example 1 Show current online OLT epon olt Following is online olt list Slot Olt Mac Address Online Status 1 1 00 a1 02 01 01 26 Online 1 2 00 a1 02 01 01 27 Online 3 1 00 0d b6 37 23 00 Online 3 2 00 0d b6 37 23 01 Online 2 Manage PON 1 of PON card under OLT Slot 3 epon olt 3 1 epon slot3 olt1 epon slot3 olt1 input or help to show the command directory admin set olt administrate status bridge set olt bridge configuration default reset olt default configuration ext mgmt extern network management link enter link config mode 20 1N OVERIEK GEPON OLT CLI User Manual onu enter onu config mode overwrite linkid overwrite linkid when linkid is exhausted overwrite onuid overwrite onuid when onuid is exhausted reboot reboot pon card restore restore to saved configuration save save pon card configuration show show olt base configuration 4 3 4 2 Enable OLT Command i epon slot3 olt1 admin enable di
11. 1 1 FD104H 00 a1 02 0a a1 08 V01 v2 24 3 1 2 FD104H 00 a1 02 0a a1 10 V01 v2 24 2 Enter ONU1 management interface epon slot3 olt1 onu 1 epon slot3 olt1 onu1 31 1N OVERIEK GEPON OLT CLI User Manual epon slot3 olt1 onu1 input or help to show command directory default restore to default setting igmp onu igmp snooping configuration info onu device user information loopback test loopback test ponport onu pon port configuration port enter onu port config mode reboot reboot the system restore restore to saved configuration rstp onu rapid spanning tree config save save onu configuration user traffic enable or disable user traffic vlan type set onu additional vlan ethertype 4 3 4 7 1 Restore ONU Default Configuration Command pon slot3 olt1 onu1 default Grammar Function Restore ONU default configuration Remark The command will delete all ONU s configuration to restore default configuration The ONU will reboot automatically 4 3 4 7 2 ONU IGMP Snooping 4 3 4 7 2 1 Configure ONU Port s IGMP Number Command epon slot3 olt1 onu1 igmp port port groups lt groupnum gt Grammar Configure ONU port s supported IGMP number Function 0 means to disable IGMP Snooping function port Appoint ONU s port number with value range from fe1 to fe8 groupnum Set ONU port s IGMP number with valid value range from 0 to 64
12. 3 4 3 4 Unknown MAC Restriction Configuration Command epon slot3 olt1 bridge dsc unk mac enable disable Grammar Function Set unknown MAC restriction mode enable disable enable unknown DA downlink packet deliver the broadcast to all 22 1N OVERIEK GEPON OLT CLI User Manual ports disable unknown DA downlink packet is abandon 4 3 4 3 5 Forward Tag Frame Configuration Command epon slot3 olt1 bridge tag on sbrg lt enable disable gt Grammar Function Set tag forwarding rules under simple bridge mode i enable allow forwarding tag frame enable disable disable dump tag frame 4 3 4 4 Restore PON Default Setting Command epon slot3 olt1 default Grammar Restore PON Default Setting Function Remark The command will delete PON card s all setting and restore the ex factory default setting And the PON card will reboot automatically 4 3 4 5 External UDP Management Function The third party network management software could manage the GEPON system via the original Teknovous Host Interface with UDP packet package Ethernet Header IP Header UDP Header TK Host Interface Since FD2102T s PON card has only one OLT chipset the configuration for slotX olt2 is the same as that for slotX olt2 4 3 4 5 1 Configure management host s IP and UDP Port Command pon slot3 olt1 ext mgmt host lt ip add g
13. 5 Configure RSTP Port Parameter 4 3 8 5 1 Set RSTP s Edge port Management Command epon rstp port lt portlist gt edgecfg lt edge gt Grammar Configure RSTP port s managed edge port attribute Appoint the port End whether to be edge port or not Edge port does not go through unction discarding learning forwarding step but transfer to switch status directly lt portlist gt Appointed port list an one from gel to ge8 d Configure appointed RSTP port s edge port attribute with byte value edge d such as edge non edge and auto 4 3 8 5 2 Set RSTP Port s Protocol Version Checkout Command epon rstp port lt portlist gt mcheck Grammar Configure RSTP port s protocol version check out When executing this command the appointed port s mode is force to be the same as Pancha next received BPDU packet version H the next packet is STP BPDU packet the port s mode is STP If it s RSTP BPDU packet the port s mode is RSTP RSTP port s protocol version is a booting command not available to preserve the attributed value continually lt portlist gt Appointed port list an one from gel to ge8 57 GEPON OLT CLI User Manual es OVERIEK 4 3 8 5 3 Set RSTP Port s Point to Point Attribution GEPON OLT CLI User Manual Command i epon rstp port lt portlist gt p2pcfg p2p Grammar Configure RSTP port s point to point index whether the appoin
14. Mode Command epon trunk lt trunkid gt Grammar Create a trunk group and enter the trunk management mode for Function i configuration trunkid Trunk number with valid value from 1 to 8 Example 1 Create trunk 1 and enter trunk 1 s management mode epon trunk 1 epon trunk1 epon trunk1 input or help to show current directory balance algorithm set trunk balance algorithm delete delete the specifically trunk member Set trunk member 4 3 13 1 Configure Trunk Balance Algorithm Command epon trunk1 balance algorithm balance Grammar Configure trunk s balance algorithm All balance algorithm is the same when all trunk group adopts the same balance algorithm B bee Trunk group s packet can be shared among trunk member poprts GEPON system support several balance algorithm such as based on MAC address IP address transmission port number MAC IP MAC transmission port number 76 es OVERIEK lt balance gt Trunk algorithm with valid index mac based on MAC address s KE balance algorithm Ip based on IP address s balance algorithm l4port based on transmission port s balance algorithm ip mac based on MAC IP address s balance algorithm lAport mac inl2if based on packet receiving port s balance algorithm 4 3 13 2 Delete Trunk Group Command epon trunk1 delete Grammar Function Delete trunk group and its mem
15. Set Port s RX Frames Tvpes nennen nennen enne 62 4 3 10 2 Set Portes Default Priority Level 62 4 3 10 3 Configure Port s Duplex Mode esee 62 4 3 10 4 Enable Port 63 4 3 10 5 Disable PO t eere ien rire nter nen ege enin earn hn 63 4 3 10 6 Configure Port s Flow Control Mode esee 63 4 3 10 7 Set Port s RX Filter Function esses enne enne 64 4 3 10 8 Configure Port Mode 64 4 3 10 9 Enable Port s Nest Vlan Function eenrnnonrnnonnrnrnnrnnrnrnnenrnnenvnnennrnsensnsen 64 4 3 10 10 Enable Port s Protocol Van 64 431011 Set bortebVlb egen degen 65 4 3 10 12 Configure Portes Rate Limit 65 4 3 10 13 Configure Portes Reauto Negotiation Function rrrnnrrrrrnnnvvrnrnnnvnrnnnn 66 4 3 10 14 Show Port Information 67 4 3 10 15 Configure Portes Compulsive Shutdown Function 67 1N OVERIEK GEPON OLT CLI User Manual 4 4 4 5 4 3 10 16 Remove Compulsive Shutdown Port 67 4 3 10 17 Configure Current Port Rate 68 4 3 11 System Configuration Mode 68 4 3 12 Synchrony with ONU Configuration nennen nennen 69 4 3 12 1 Backup EPON System Configuration 69 4 3 12 2 Restore EPON System Configuration rrrrnnnnvrrnnnnrvrrnnnnrvrrnnnnvnrnnnnnvnrnnnn 69 4 3 12 3 Configure Console Port Speed 70 4 3 12 4 ONU Authorization Management Mode 70 4 3 12 5 Set SNMP Read Community sess 73 dap Reboot OLET ient tr nesen lis es E Re rta EY RE de Deenen 73 4
16. and set tag rules lt vlanid gt Appoint added Vlan with valid value from 0 to 4094 Output rule frames from this port could be changed based on the optional index below lt tagModify gt pass mo modification addtag add vlan tag to untag frames Example 1 Add vlan100 to ONU UNI port 1 and output rule is to remove the tag epon slot3 olt1 onu1 fe1 vlan add 100 deltag 43 1N OVERIEK GEPON OLT CLI User Manual 4 3 4 7 8 1 2 Delete VLAN Command Grammat pon slot3 olt1 onu1 fe1 vlan delete lt vlanid gt Function Delete appointed ONU UNI port s Vlan lt vlanid gt Appointed vlan to be deleted with valid value range from 0 to 4094 4 3 4 7 8 1 3 Configure ONU UNI Port s VLAN Forward Policy Command Gramar epon slot3 olt1 onu1 fe1 vlan policy policy Function Configure ONU UNI port s VLAN forward policy ppoint onu UNI port s VLAN forward policy with the index below policyO Switch frames on default vlan domain frames and ignore frame VID lt policy policy1 Switch VID frame unknown VID treated as untagged policy2 switch VID frame and ignore unkown VID frames policy3 switch VID frames on the vlan domain appointed by the PON port Example 1 Configure ONU UNI port 1 s VLAN with strategy 3 epon slot3 olt1 onu1 fe1 vlan policy policy3 Illustration Different VLAN forward policy deal with different frame types 5 PolicyO Switch frames on default
17. ennns einen enn 50 4 3 62 Delete Protocol eroe enirn n rer edE Env r S rene UR ee 51 4 3 6 3 Clear Protocol Pool eegne eegene aene Eege AEN 51 4 3 6 4 Add Bind Rule 52 4 3 6 5 Remove Bind Rule eonnrnonnrnnonvnnennrnennrnsnnrnnenrnnenvernrnnenvenennrnsnnrnsenrnsensesenen 52 4 3 6 6 Enable Port Protocol VLAN Function sreronrnnonrnnnnrrnennrnnenrnsernrenrnsenvenener 53 4 3 6 7 Disable Port Protocol VLAN FUNCTION nennen 53 4 3 6 8 Show Protocol VLAN s Configuration Information sess 53 4 3 7 Configure Switch Control Card s Global Parameter of Port Limit 54 4 3 8 RSTP Configuration Mode esses nnne nennen 54 4 3 8 1 Configure RSTP Bridge Parameter cc ccccccsscccssssseccssseeeesssseeessssseeees 55 4 3 8 2 Enable RSTP Function sese eene ener entis nnne 56 4 3 8 3 Disable RSTP Function anrnronrnnonnnnennrnsnnrnnenrnnenvnnenvrnennrnsrensnnrnsenrnsensesenen 56 4 3 8 4 Hold Bridge Forwarding Frame Count esses 57 4 3 8 5 Configure RSTP Port Parameter 57 4 3 8 6 Show RSTP Configuration Information 59 4 3 9 Configure Switch Control Card s Switching Mode eese 60 4 3 9 1 Set Private Vlan Mode enne nenenn 60 4 3 9 2 Show Switch Control Card s Switch Mode Configuration 60 4 3 9 3 Enable Switch Control Cards Vlan Function 61 4 3 10 Uplink Port Management mode of Switch Control Card 61 4 3 10 1
18. ge13 is disabled Protocol based VLAN on ge14 is disabled Protocol based VLAN on ge15 is disabled Protocol based VLAN on ge16 is disabled 4 3 7 Configure Switch Control Card s Global Parameter of Port Limit Command epon rate ctrl mode lt bps pps gt Grammar Function Set control card s globalParameterof input switch speed Globalindex s speed unit lt bps pps gt bps bytes per second pps frames per second 4 3 8 RSTP Configuration Mode Command epon rstp 54 1N OVERIEK GEPON OLT CLI User Manual Grammar Function Enter switch control card s RSTP management mode Xt Example 1 Enerer RSTP Management Mode epon rstp epon rstp epon rstp input or help to show current directory bridge bridge disable disable rstp enable enable rstp hold count set rstp transmit hold count port rstp port parameter configuration show show rstp configuration 4 3 8 1 Configure RSTP Bridge Parameter 4 3 8 1 1 Bridge Forward Delay Command epon rstp bridge fdelay fdelay gt Grammar Function Set RST Bridge delayed forward Value range 4 30 must demand the following bind relation 2x ForwardDelay 1 0second gt MaxAge fdelay d g MaxAge is bridge infomration s maximum valid time ForwardDelay forward delay 4 3 8 1 2 Bridge Maximum Valid Age Command epon rstp bridge ma
19. outband management CAT4 cable to management port After Telnet to CLI interface we can manage the GEPON products Defualt outband network management IP 192 168 120 100 Default inband network management IP 192 168 1 100 2 4 User Login EPON CLI System System provide two login accounts default as follows User Password admin Admin guest Blank After you log in successfully the following interface pops up IZN OVERIEK D X Command Line Interface for EPON System Hardware Ver OLT 1 Software Ver OLT EPONGWGG 1 3 1 Created Date fug 15 2012 15 35 83 Copyright lt c gt 2086 2012 All rights reserved DEDEDEDEDEDEDEDEDEDEDEDE DEDEDEDE DEDE DEDEDEDEDEDE DEDE DEDEDEDE DEDE DEDE DEDE DEDE DEDEDEDE DEDE DEDE DEDE DEDE DEDEDEDEDEDE DEDEDEDEDEDEDEDE DEDEDEDE BLogin admin Password le pon gt enable password IT When the command lines shows epon gt user can input the configuration command to mange or inquire the configuration information 3 Command Format Illustration 1 Command Conventions 2 Keyboard Operation Conventions 3 Symbols Boldf Used to highlight the key words inportant words eee that should never be modified when input EE OVERIEK GEPON OLT CLI User Manual Used to denote the parameters that should be italic replaced by actual values when practical use in command line Items keywords or arguments in square brackets are optional Alternative
20. use our EMS management to monitor and configure the whole EPON system via EMS since we have offered very powerful function and simple operation in the EMS interface 1 2 Definition Product Abbrev Description iation GEPON Gigabit Ethernet Passive Optical Network OLT Optical Line Terminal ONU Optical Network Unit Zem OVERIEK GEPON OLT CLI User Manual 2 Configuration Preparation 2 1 Management Model RI PS a ED DNE EE EE T EEE ETE MEG TE NG Protocol i snmp UDP console or telnet l Management console p management GEPON OLT out of band management connect to management port in band management connect to gel ge8 port console management connect to console port 2 2 Console Port Connection There is a Console port in the front panel of Switch Control Card The command line configuration interface is enabled via console port connecting to the NMS s superior terminal Super terminal s basic configuration is as follows 1N OVERIEK GEPON OLT CLI User Manual COM3 Properties Port Settings I Bits per second 9600 Data bits 8 Parity None Stop bits SE Flow control None Restore Defaults 2 3 Network Connection FD2100S support inband management CAT5 connect to ge1 ge8 port and
21. 3 12 7 Restore Default Configuration and Reboot Equipment 74 4 3 12 8 Save Current Configuration cccccccccssscccsssseeeesssseecesseeeesssseeeessseeeees 75 4 3 12 9 Set Trap Receiving IP Address 75 4 3 12 10 Set SNMP Written Community 75 4 3 13 Trunk Management Mode 76 4 3 13 1 Configure Trunk Balance Algorithm eese 76 4 3 13 2 Delete Trunk Group um iu iiie aiite nota rtr tiere rr te roga pega MERE 77 4 3 13 3 Add Trunk Member eene eene nnne entente 77 4 3 14 Show Trunk Configuration Information 77 KREEG ZWEE Tu 78 4 3 15 1 Set User Authority iiciin aa 78 43152 Add USM E 78 4 3 15 3 Delete User opzesteigen enge 79 4 3 15 4 Change User Password enne enne nnne 79 4 3 15 5 Show Current User s Information 79 4 3 15 6 Change User s TIMEOUT enne 80 4 3 16 VLAN Management Mode 80 4 3 16 1 Delete Vlan Member nere enne nennen eene 81 4 3 16 2 Delete V ari iier irte ERR eee ente E ERIS PE ER ERE IER 81 4 3 16 3 Add Vlan Member Port let 81 4 3 17 Show Vlan Configuration Information 82 Show System Running Information eese eene enne enne 83 4 4 1 Show System s Current CPU Running Status 83 4 4 2 Show System s Memory Use Status 83 4 4 3 Show System s Task Status rrrrnnrrrrnnnnvrrnnnnnvnrnnnnvvnrnnnnvnrnnnnnnnrnnnnnnnssnnnvnrsnnnnsnnnn 84 4 4 4 Enable CATV RF Function eene nennen nnne 84 4 4 5 disable CATV RF Cut Off Function rrrnnnnrrrrrrrrrrn
22. 3 4 7 7 1 1 Add Vlan Command e epon slot3 olt1 onu1 ponport vlan add lt vlanid gt lt tagModify gt Grammar Function Add valn for onu PON port and set output tag rule lt vlanid gt Appoint added vlan with value range from 0 to 4094 Output rule frames from this port could be changed based on the optional index below pass mo modification lt tagModify gt addtag add vlan tag to untag frames deltag remove the outward tag if vlan tag exsit Example 1 Add vlan100 to ONU PON port and output rule is to add tag epon slot3 olt1 onu1 ponport vlan add 100 addtag 40 LAN OVERIEK GEPON OLT CLI User Manual 4 3 4 7 7 1 2 Delete VLAN Command epon slot3 olt1 onu1 ponport vlan delete vlanid Grammar Function Delete appointed ONU UNI port VLAN lt vlanid gt Appoint vlan to be deleted with valid value from 0 to 4094 4 3 4 7 7 1 3 Configure VLAN Forward Policy Command epon slot3 olt1 onu1 ponport vian policy lt policy gt Grammar Function Configure ONU PON port s VLAN forward policy Appoint onu pon port s VLAN forward policy with the index below policyO Switch frames on default vlan domain frames and ignore frame VID policy policy1 Switch VID frame unknown VID treated as untagged policy2 switch VID frame and ignore unkown VID frames policy3 switch VID frames on the vlan domain appointed by the UNI port Exampl
23. GEPON OLT OT 2000S CLI User Manual V1 Unotrade Technologia Ltda 1N OVERIEK GEPON OLT CLI User Manual Contents 1 Preface eme 6 1 1 EO CUCUION EE 6 1 2 Prime c H 6 2 Configuration Preparation eene eene enne nennen nnnn sene nnn sen nenn seen essere nne 7 2 1 Management Model 4 erre kne aede redox a repe re ERR rev EEE 7 2 2 Console Port ConnectlOn uere tee on reso terrae rere ENEE Ure SR e HER e Ere alpes 7 2 3 Network Connection 8 2 4 User Login EPON CLI System AAA 8 3 Command Format llIuStratiOD ctr retener Yee tue Ee Rep Pro DER HER YN RHET RARE EPIRI ERU US 9 3 1 Command Form t PE dansen 9 3 2 Typical Parameter Category 11 4 System Root Directory eerrrrrovererernvnrerevennvnnsvsnsnsvsvnnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnes 13 4 1 Enable System Log Printed to Super Terminal 13 4 2 System Debug Mode ca tette ancien c eode ae oy aru CAN eda a 13 4 2 1 CL mM 14 4 2 2 elle ME 14 4 2 3 Drag H A 14 4 3 dirje2u 15 4 3 1 Switch Control Card MAC Address Management 15 4 3 1 1 Configure Switch Control Card s MAC Aging Time 15 4 3 1 2 Show Switch Control Card s MAC Address List eeeessessss 16 4 3 2 Port mirror Management 16
24. Management Command epon slot3 olt1 onu1 user traffic oper Grammar i Configure ONU user s traffic flow management Function i When input user to show the onu user s current traffic flow enable enable onu user s traffic flow oper Disable disable onu user s traffic flow 4 3 4 7 13 Configure ONU VLAN s Ethernet Parameter Command epon slot3 olt1 onu1 vlan type ethtype type upstream lt uptag gt Grammar downstream dntag Configure onu vlan s Ethernet type and set this vlan s Ethernet traffic Function direction Input vlan type to show onu s current VLAN Ethernet information VLAN s Ethernet type with default value as 0x8100 and the valid value type range from 0 to 65535 Whether add the vlan tag of the vlan Ethernet type for the uplink e traffic uptag pe tag add tag Untag do not add tag Whether add the vlan tag of the vlan Ethernet type for the downlink traffic lt dntag gt tag add tag Untag do not add tag 47 1N OVERIEK GEPON OLT CLI User Manual 4 3 4 8 Configure Link ID Overwrite Function Command CE epon slot3 olt1 overwrite linkid oper Grammar Whether new authorized link overwrites the existing link ID after the Function Link ID is set oper Enable new Link overwrites existing Link ID Disable new Link does not overwrite existing Link ID 4 3 4 9 Configure ONU ID Over
25. Port s Duplex Mode Command Grammar epon ge1 duplex duplex gt 62 GEPON OLT CLI User Manual 1N OVERIEK GEPON OLT CLI User Manual Function Set switch control card port s duplex mode full full duplex mode lt duplex gt half half duplex mode auto auto negotiation mode 4 3 10 4 Enable Port Command epon ge1 enable Grammar Enable the switch control card port to deliver and receive packet Function Under some circumstance user can use this function to test the networking performance 4 3 10 5 Disable Port Command epon ge1 no enable Grammar Disable the switch control card port to deliver and receive packet Function Under some circumstance user can use this function to test the networking performance 4 3 10 6 Configure Port s Flow Control Mode Command epon ge1 flow ctrl lt ctrl gt Grammar Configure switch control card port s flow control mode Both optical port mode and electrical mode could support flow control configuration enforcedly and auto negotiation Function Under the half duplex mode the port enable the back flow control function default Under the full duplex mode you can enable or disable flow control in compliant with 802 x standard enable enable flow control function ctrl disable disable flow control function 63 1N OVERIEK GEPON OLT CLI User Manual auto auto negotiatio
26. The maximum bandwidth must higher than or equal to the minimum guaranteed bandwidth 4 3 4 6 8 3 Configure Link Transmission Time Delayed Level Command epon slot3 olt1 link1 sla lt dir gt level lt level gt Grammar Function Configure uplink or downlink s transmission delayed time level Two direction Parameter optional lt dir gt downstream upstream Appoint downlink or uplink s transmission delayed time level with the valid value as follows lt level gt Le M m Sensitive sensitive service could be given the priority to transmit tolerant non sensitive service 4 3 4 6 8 4 Configure Link s Maximum Burst Flow Command f i epon slot3 olt1 link1 sla dir burst size burst Grammar Function Configure uplink or downlink s maximum burst flow Two configuration direction as follows dir downstream upstream Appoint the link s maximum burst flow with the valid value range burst from 1 to 256 29 1N OVERIEK GEPON OLT CLI User Manual 4 3 4 6 8 5 Show LINK SLA Configuration Command epon slot3 olt1 link1 sla lt dir gt Grammar Function Show uplink or downlink s SLA configuration information downstream or dir upstream Example 1 Show current uplink s SLA configuration information epon slot3 olt1 link1 sla upstream Current Link SLA configuration Upstream minimum guaranteed bandwidth 0 Kbps maximum allow
27. ammar Save current configuration Function Just input save command to save the switch control card s current configuration Appoint the device to save current configuration with valid index ctrl card save switch control card s current configuration slot olt onu is ignored pon card save appointed PON card under slot configuration device olt onu is ignored onu save configuration for appointed onu with index slot olt onu all save system s all default configuration and command slot olt onu is ignored slot Appoint PON card slot number with valid value from 1 to 4 olt Appoint PON port number with valid value from 1 to 2 onu Appoint ONU number with valid value from 1 to 64 4 3 12 9 Set Trap Receiving IP Address Command epon sys trap addr index lt ip addr gt Grammar Function Configure GEPON s receiving trap IP address with 4 IP at most lt index gt Trap receiving IP index with valid value from 1 to 4 lt ip addr gt Set trap receiving IP address such as 192 168 0 1 4 3 12 10 Set SNMP Written Community Command epon sys write comm community 75 1N OVERIEK GEPON OLT CLI User Manual Grammar Function Set SNMP s written community of EMS software Written community with bytes serial longest length 26 bytes such lt community gt as private 4 3 13 Trunk Management
28. ard port s auto negotiation function which is needed on the purpose of networking debugging This function could be replaced by means of plug in and out of the cable but if the Function cable fiber is too complicated or too far it is better to realize it via software Therefore port configuration management module must provide a command port for reauto negotiation command which doesn t preserve the attributed value continually 66 IZN OVERIEK 4 3 10 14 Show Port Information GEPON OLT CLI User Manual Command epon ge1 show Grammar Function Show switch control card port s configuration information Example 1 Show switch control card port 1 s configuration information epon ge1 show M Portld 1 Attribution Mode copper AdminStatus enable PVID eil DefaultPriority 0 IngressFilter disable AccFrameType call CfgSpeed auto CfgDuplex auto CfgFlwCtrl auto shutDown no BcRateCtrl disable McCtrlMode disable UnkUcRateCtrl disable RateCtriMode BPS BcRateThrs 0 ProtStatus down WorkSpeed 10m WorkDuplex half WorkFlwCtrl enable LinkStatus down End 4 3 10 15 Configure Port s Compulsive Shutdown Function Command Grammar Function epon ge1 shutdown Configure switch control card port s compulsive shutdown function In an exceptional case such as attached by virus or hacker and can t take an
29. ase do save the configuration under the system directory after changing the password and reboot the system to make the setting valid 4 3 6 Protocol VLAN Configuration Mode Command epon prot vian Grammar Enter switch control card s protocol based vlan managmenet mode Function where you can configure supported protocol pool port and bind relation between protocol and Vlan Example 1 Enter protocol based VLAN management mode epon prot vlan epon prot vlan t epon prot vlan input or help to show the current directory add add a protocol type no bind bind or unbind portlist protocol type to vlanid clean delete all protocol type delete delete a protocol type no enable enable protocol vlan for ports show show protocol vlan config 4 3 6 1 Add Protocol Command epon prot vlan add prot type lt protocol type gt Grammar Add a protocol for the globalallowed protocol pool Only the protocol Gasen added to the protocol pool can bind the port protocol vlan Protocol unction pool can add 8 protocols at most now Alarm is show when adding more than 8 protocol vlans 50 1N OVERIEK GEPON OLT CLI User Manual Appoint added protocol type with valid value hex based Ox as prefix or protocol name s bytes series common protocol name could only lt protocol type gt support ip arp and pppoe such as 0x8863 pppoe etc Example 1 Add pppoe p
30. ber 4 3 13 3 Add Trunk Member Command epon trunk1 member lt portlist gt Grammar Function Add trunk group s member pot lt portlist gt Appoint trunk member port list from ge1 to ge8 Example 1 Add member port ge1 ge3 ge4 and ge8 to trunk 1 epon trunk1 member ge1 ge3 ge4 ge8 4 3 14 Show Trunk Configuration Information Command epon show trunk Grammar Function Show switch control card s current trunk configuration Example TI GEPON OLT CLI User Manual 1N OVERIEK GEPON OLT CLI User Manual 1 Show switch control card s current trunk configuration epon show trunk Traffic balance algorithm 1 based on mac address Trunk 1 member ports ge1 ge3 ge4 ge8 4 3 15 User Management 4 3 15 1 Set User Authority Command epon user access name lt access gt Grammar Change appointed user s priority mode to limit use to access to Function 2 system or limit the user right Appointed user name under the priority mode with the length from 4 name to 15 bytes admin manager who has all the configuration and operation rights access Guest guest who could only ready the operation Configuration Remark Only the system administer has the rights to change the system user s priority 4 3 15 2 Add User Command epon user add name passwd lt access gt Grammar Functi
31. block Grammar Function Block current link to stop the link s data flow 4 3 4 6 2 Remove the Current Link Block Command epon slot3 olt1 link1 no block Grammar Function Remove the current link block to restore the link s data flow 4 3 4 6 3 Clear Link s Dynamic MAC Address List Command epon slot3 olt1 link1 dynamic mac clear Grammar Function Clear link s dynamic MAC address list 26 ILN OVERIEK GEPON OLT CLI User Manual 4 3 4 6 4 Show Link s Dynamic MAC Address List Command epon slot3 olt1 link1 dynamic mac list Grammar Function Show all the MAC address list learned from the link Remark Please use the command dynamic mac refresh to refresh the link s dynamic MAC address before showing the link s dynamic MAC address 4 3 4 6 5 Refresh Link s Dynamic MAC Address List Command epon slot3 olt1 link1 dynamic mac refresh Grammar Function Refresh link s dynamic MAC Address 4 3 4 6 6 Force Rediscovering Link Command epon slot3 olt1 link1 rediscover Grammar Function Force the link rediscovering to OLT 4 3 4 6 7 Show LINK Basic Information Command epon slot3 olt1 link1 show Grammar Function Show the link s current basic configuration information Example 27 1N OVERIEK GEPON OLT CLI User Manual 1 Show the current link s basic configuration information epon slot3
32. derthe protocol vlan configuration mode 4 3 5 6 Enable Port Protocol VLAN Function 4 3 5 7 Disable Port Protocol Vlan Function 4 3 10 11 Set Port s PVID Command epon ge1 pvid lt pvid gt Grammar Function Configure switch control card port s default vlan ID lt pvid gt Vale range from 0 to 4094 4 3 10 12 Configure Port s Rate Limits 4 3 10 12 1 Enable Broadcast Restriction Function Command epon ge1 rate ctrl broadcast status Grammar Function Enable switch control card port s broadcasting restriction function status enable disable 4 3 10 12 2 Enable IGMP Restriction Function Command epon ge1 rate ctrl multicast status Grammar 65 1N OVERIEK GEPON OLT CLI User Manual Function Enable switch control port s IGMP function enable lt status gt disable 4 3 10 12 3 Set Restriction Rate Command epon ge1 rate ctrl threshold threshold Grammar Function Set switch control card port s restricted packet rate limits threshold Vale range 0 1000000 4 3 10 12 4 Enable Unknown Unicast Restriction Function Command epon ge1 rate ctrl unkown uc status Grammar Function Enable unknown unicast restriction function enable status i disable 4 3 10 13 Configure Port s Reauto Negotiation Function Command epon ge1 reautoneg Grammar Configure switch control c
33. e 1 Configure ONU PON port s forward policy 3 epon slot3 olt1 onu1 ponport vlan policy policy3 Illustration Different VLAN forward policy deal with different frame types 1 PolicyO Switch frames on default vlan domain and ignore frame VID Frame Type Approach Untagged Frame Switch frames on default vla PVID n domain Tagged Frame Ignore frame s VID treated as untagged frame 2 policy1 Switch VID frame unknown VID treated as untagged Frame Type Approach 41 ZN OVERIEK Untagged frame GEPON OLT CLI User Manual Switch frames on port s default Vian domain Tagged frame the ONU port is on the vlan domain Switch frames on frame VID s VLAN domain Tagged frame the onu port is not on the vlan domain Switch frames on port s default VLAN PVID domain Tagged Frame VLAN doesn t exsit Switch frames on port s default VLAN VPID domain 3 policy2 switch VID frame and dump unkown VID frames Frame Type Approach Untagged frame Switch frames on port s default VLAN VPID domain Tagged frame the ONU port is on the vlan domain Switch frames on frame VID s VLAN domain Tagged frame the onu port is not on the vlan domain Tagged Frame VLAN doesn t exsit add the port to the VLAN domain temporialy and forward frames on fram VID s VLAN domain Ignore the frame 4 policy3 switch VID frames on the vlan domain appoi
34. e Management Port s IP and Sub Mask Command i epon net address ifx name lt ip addr gt lt ip mask gt Grammar Configure network port s IP address and submask Currently our network management port includes inband network management Function port viO and outband network management port cpmO input address ifx name could show the current networking configuration i Appointed ip port name which could be viO or cpmO port format ifx name e expression mode refer to typical Parameter category lt ip add gt Configure IP address lt ip mask gt Configure appointed IP address s network mask Example 1 Enquiry the current inband network management port s network configuration epon net address viO Interface viO Ip address 192 168 1 100 Netmask 255 255 255 0 associated vlan 1 admin status operational Example 2 Configure inband management IP as 192 168 1 1 mask is 255 155 155 0 epon net address vi 192 168 1 1 255 255 255 0 Example 3 Configure outband management IP as 192 168 1 2 and mask is 255 255 255 0 epon net address cpmO 192 168 1 2 255 255 255 0 4 3 3 2 Configure NMS Port Gateway Command epon net gateway lt ip addr gt Grammar 19 1N OVERIEK GEPON OLT CLI User Manual Configure NMS port s gateway Function e Input command gateway to show the current gateway information lt ip addr gt
35. e raw commands global C functions show show various parameters 4 1 Enable System Log Printed to Super Terminal Command epon gt no copy log Grammar Function Show current System Log 4 2 System Debug Mode Command epon debug Grammar Function enter debug mode Remark entering exit could return to the current mode You will find the command as follows after entering debug mode epon input or help to show the current directory debug debug specific module dump show module internal data log lvl set log level for specific module 13 1N OVERIEK GEPON OLT CLI User Manual 4 2 1 debug Command epon debug module lt moduleld gt Grammar Function Configure the module s debug functions Remark This command isn t valid yet 4 2 2 dump Command epon dump module lt moduleld gt Grammar Function Configure the module s dump functions lt moduleld gt Module ID format please refer to 3 3 typcial Parameter category 4 2 3 log lvl Command epon Log lvl module lt moduleld gt level Grammar Function Change module s LOG level Module ID definition format refer to typical Parameter categor lt moduleld gt n m illustration There are 5 level for LOG level marked from 0 to 4 0 is the highest level O critical event level 1 important event 2 general event 3 trivial event 4 debug message
36. eboot ctrl card 2 Reboot PON card 2 epon sys reboot pon card 2 3 Reboot the ONU1 under PON 2 of slot3 epon sys reboot onu 3 2 1 3 Reboot the whole EPON system including switch control card all online PON card and all online ONU epon sys reboot all 4 3 12 7 Restore Default Configuration and Reboot Equipment Command i epon sys restore device slot olt onu Grammar Restore ex factory default configuration and reboot the device Function When device slot olt onu is ignord the command just restore switch control card configuration Appoint the device to restore default configuration with valid index ctrl card restore switch control card s default configuration slot olt onu is ignored pon card restore appointed PON card under slot configuration device olt onu is ignored onu restore default configuration for appointed onu with index slot olt onu all restore system s all default configuration and command lt slot gt lt olt gt onu is ignored slot Appoint PON card s slot number with valid value from 1 to 4 olt Appoint PON port number with valid value from 1 to 2 onu Appoint ONU number with valid value from 1 to 64 74 1N OVERIEK GEPON OLT CLI User Manual 4 3 12 8 Save Current Configuration Command i epon sys save device slot olt onu Gr
37. ed bandwidth 1000000 Kbps delay sensitive Tolerant max burst size 100 KBytes sla state Enable 2 Show downlink s SLA configuration information epon slot3 olt1 link1 sla downstream Current Link SLA configuration Downstream minimum guaranteed bandwidth 0 Kbps maximum allowed bandwidth 1000000 Kbps delay sensitive Tolerant max burst size 100 KBytes sla state Enable 4 3 4 6 9 Add Link s Static MAC Address Command epon slot3 olt1 link1 static mac add mac Grammar Function Add link s static MAC address mac Input MAC address 30 oN OVERIEK GEPON OLT CLI User Manual 4 3 4 6 10 Delete Link s Static MAC Address Command epon slot3 olt1 link1 static mac del mac Grammar Function Delete Appointed Link s Static MAC Address mac Input the deleted MAC address 4 3 4 6 11 Show Link s Static MAC Address List Command e epon slot3 olt1 link1 static mac list Grammar Function Show the link s static MAC address 4 3 4 7 ONU Management Mode Command i epon slot3 olt1 onu lt onuid gt Grammar Function Enter ONU management mode and configure the ONU Parameter lt onuid gt Input onuid with the valid value range from 1 to 64 Example 1 Show current online ONU epon slot3 olt1 onu Following is online onu list slotid oltld onuld deviceType basedMac hWRev fwRev 3
38. elete this vlan and member port lt portlistt gt Appoint vlan member port list am port from gel to ge16 4 3 16 2 Delete Vian Command epon vlan100 delete Grammar Function Delete current vlan and all member ports under this vlan 4 3 16 3 Add Vlan Member Port list Command epon vlan100 member lt portlist gt tag Grammar Function Add vlan member port and set its tag mode lt portlistt gt Added vlan member port list from ge1 to ge16 Tag mode with fixed index tag e When the member port is marked with tag The packet from the port tag d is added with vlan tag When tag is deleted this port is not marked with tag Example 1 add switch control card port ge1 ge2 ge3 with vlan 100 to the tag member ports while port ge4 ge5 ge16 are member ports with vlan100 without tag epon vlan100 member ge1 ge3 tag epon vlan100 member ge4 ge5 ge16 81 1N OVERIEK GEPON OLT CLI User Manual 4 3 17 Show Vlan Configuration Information Command epon show vlan Grammar Function Show switch control card s vlan configuration information Example 1 Show switch control card s valn configuration epon show vlan vlan 1 tagged ports untagged ports ge1 ge16 vlan 100 tagged ports ge1 ge3 untagged ports ge4 ge5 ge16 82 IEN OVERIEK GEPON OLT CLI User Manual 4 4 Show System Running Information 4 4 1 Show Sys
39. frame the onu port is not on the vlan domain Ignore the frame Tagged Frame VLAN doesn t Ignore the frame exsit 4 3 4 7 8 1 4 Configure ONU UNI Port s PVID Command epon slot3 olt1 onu1 fe1 vlan pvid vlanid Grammar Function Configure ONU UNI port s default VLAN ID PVID lt vlanid gt Appoint Vlan ID with valid value range from 0 to 4094 45 ZN OVERIEK Example 1 Configure ONU UNI port1 s PVID as 100 epon slot3 olt1 onu1 fe1 vlan pvid 100 4 3 4 7 8 1 5 Show ONU UNI Port s VLAN Configuration Command epon slot3 olt1 onu1 fe1 vlan show Grammar Function Show ONU UNI port s Vlan configuration information 4 3 4 7 9 Reboot ONU Command Grammar Function epon slot3 olt1 onu1 reboot Reboot onu 4 3 4 7 10 Configure RSTP Function Command epon slot3 olt1 onu1 rstp lt oper gt Grammar Configure ONU s rapd spanning tress protocol RSTP function Function Input rstp to show current RSTP status Enable disable ONU RSTP function with valid value as follows oper Enable enable ONU RSTP function Disable disable ONU RSTP function 4 3 4 7 11 Save ONU configuration Command Grammar pon slot3 olt1 onu1 save 46 GEPON OLT CLI User Manual 1N OVERIEK GEPON OLT CLI User Manual Function Save ONU s all configuration 4 3 4 7 12 Configure ONU s Traffic Flow
40. h as 00 A1 02 02 01 FO Set onu authorization type under address list with following value Blacklist the ONU with this type of MAC address can t be authorized type to OLT Whitelist the onu beyond this MAC address range can t be authorized Example 1 Add the ONU with the MAC address 00 A1 02 01 12 B0 to the blacklist epon sys onuauth list add 00 A1 02 01 12 BO blacklist 71 1N OVERIEK GEPON OLT CLI User Manual 4 3 12 4 2 2 Delete ONU Authorized Address List Command epon sys onuauth Hlist delete index Grammar Function Delete an ONU address list index MAC address list index 4 3 12 4 2 3 Show Current MAC Address List Command i epon sys onuauth list show Grammar Faiet Show current ONU authorized address list and distribute an index unction directory for all the MAC address automatically Example 1 Show current ONU authorized MAC address list epon sys onuauth list show NO Start Address End Address Type 1 00 a1 02 01 12 b0 00 a1 02 01 12 b0 blacklist 4 3 12 4 3 Configure ONU Authorized Type Command epon sys onuauth type lt type gt Grammar Function Set GEPON system ONU s authorized type Valid value blacklist whitelist none gt o lt type gt Blacklist All onu in the MAC address type can t be authorized Whitelist All ONU beyond the MAC address type can t be authorized None non authori
41. how the command directory attribute onu port attribute config bridge onu port bridge parameter config dynamic mac clear clear dynamic mac table dynamic mac list show all dynamic mac table no enable enable onu port info set onu port user information qos onu port qos config vlan onu port vlan configuration 35 ILN OVERIEK GEPON OLT CLI User Manual 4 3 4 7 6 1 Configure ONU port s Parameter Attribute 4 3 4 7 6 1 1 Show ONU Port Parameter Command epon slot3 olt1 onu1 fe1 attribute Grammar Function Show ONU port s Parameter attribute Example 1 Show ONU1 s port 1 attribute ONU 3 1 1 Port fe1 attribute auto negotiation enable speed 10m duplex half flow control disable 4 3 4 7 6 1 2 Configure ONU Port Auto Negotiation Command i epon slot3 olt1 onu1 fe1 attribute auto nego oper Grammar Function Configure ONU port to be auto negotiable Value input is enable or disable enable enable the port s auto negotiation function oper d disable Disable the port s auto negotiation function 4 3 4 7 6 1 3 Configure ONU Port Speed Command epon slot3 olt1 onu1 fe1 attribute speed speed Grammar Function Configure ONU port s speed speed ONU port speed with valid value as follows 10m 100m 1000m 36 ILEN OVERIEK GEPON OLT CLI User Manual 4 3 4 7 6 1 4 Configure ONU Port s Duplex Function
42. iguration save save system configuration trap addr set trap destination IP address write comm set snmp write community string 4 3 12 Synchrony with ONU Configuration Command epon sys cfg sync slot status Grammar Configure OLT s setting is synchronous with ONU configuration When this function is enabled ONU will remove its own nvs automatically Function before ONU authorized to OLT Al configuration under the ONU will be cleared All ONU s configuration is valid after authorized under the OLT lt slot gt PON card slot with integer value from 1 to 4 lt timeout gt Optional index lt enable disable gt Remark This function default is close because enabling it will make ONU s saved configuration lost needing to configure it again undet the OLT Please use this function properly 4 3 12 1 Backup EPON System Configuration Command epon sys config backup lt host gt Grammar Function Put all EPON sytems s configuration file backup to TFTP server lt host gt Appointed TFTP server s IP address 4 3 12 2 Restore EPON System Configuration Command epon sys config upgrade host Grammar 69 1N OVERIEK GEPON OLT CLI User Manual Download system s configuration file from TFTP server and restore unction EPON system s configuration host Appointed TFTP server s IP address 4 3 12 3 Configure Console Port Speed
43. index with valid integer value from 1 to 4094 Port number including gigabitethernet ports from 1 to 16 short for gel to ge16 To mention that ge9 to ge16 can t be seen port corresponding with 8 PON ports in 4 pon cards We can say that ge9 ge16 is for PON1 PON8 configuration While ge1 ge8 is for switch control card s 8 uplink port configuration Port list such as gel1 ge5 2 ports gel ge5 meaning 5 ports portlist from ge1 to ge5 Ip port name includes inband and outband inband interfaces is embodyed with vitnumber vi means virtual interface for example vio means the first inband IP interface it s the only one interface to ifx name support inband ip interface outband interface is embody with cpm number cpm is the outband interface s device name For example cmpO means the first outband ip nterface this is the only one interface to support outband ip interface ip addr Ip address such as 192 168 1 1 ip mask Ip mask with 4 segments of algorism bytes such as 255 255 255 0 mac MAC address such as 00 01 02 02 04 05 Module ID number moduleld module name 3 common mbuf pool 4 HDLC driver 5 inter board communicaiton protocol moduleld 9 device online status maintenance 10 system basic configuration 11 user manager 12 switch port attribute management 13 switch port status poll task 14 switch port statistics poll task 11 1N OVERIEK GEPON OLT CLI User Manual 15 t
44. items are grouped in braces and separated by vertical bars One is selected Optional alternative items are grouped in square x y brackets and separated by vertical bars One or none is selected Values range from x to y One is selected A line starting with the S sign is comments Press the key with the key name inside angle brackets For example Enter Tab lt Backspace gt or lt A gt key1 key2 gt Press the keys concurrently For example Ctrl Alt A means the three keys should be pressed concurrently key1 key2 gt Press the keys in turn For example Alt A means the two keys should be pressed in turn Eye catching symbols are also used in the manual to highlight the points worthy of special attention during the operation They are defined as follow AN Caution Means reader be extremely careful Improper operation may cause data loss or damage to equipment dim Warning Means reader be extremely careful Improper operation may cause bodily injury as Note Means a complementary description 4 Hints Commands in this mannual is case sensitive 10 1N OVERIEK GEPON OLT CLI User Manual 3 2 Typical Parameter Category When configure the system with CLI command lines we will meet with some data types with fixed format which embody some index s meaning expression mode and value range Herein we list some repeated commands to explain their meaning and use vlanid Vlan
45. lt1 onu1 fe1 info lt info gt Grammar Function Set ONU port s user information Input info to show ONU port s user information lt info gt User information bytes length with the longest length 64 bytes 4 3 4 7 6 8 Configure ONU Port s Uplink Speed Limit Command epon slot3 olt1 onu1 fe1 qos ingress policing lt max rate gt Grammar lt traffic type gt Function Set ONU port s uplink bandwidth limits Input qos ingress policing to show the current uplink speed limit configuration information lt max rate gt Maximum uplink bandwidth unit kbps valid value 0 100000 Appoint speed limit s packet type with value as follows Broadcast broadcastAndMulticast traffic type broadcastMulticastAndFloodedUnicast all 39 1N OVERIEK GEPON OLT CLI User Manual 4 3 4 7 6 9 Configure ONU Port s Downlink Speed Limit Command epon slot3 olt1 onu1 fe1 qos egress shapping max rate gt Grammar schedule algorithm Set ONU port s downlink bandwidth limits Function Input qos egress shapping to show the current downlink speed limit configuration information max rate Maximum downlink bandwidth unit kbps valid value 0 100000 Port s output flow shaping s adjusty calculation method with valid schedule algor value ithm weighted fair strict priority 4 3 4 7 7 ONU Port s VLAN Configuration 4 3 4 7 7 1 ONU PON Port VALN Configuration 4
46. mple 79 1N OVERIEK GEPON OLT CLI User Manual 1 Show System s Current User List epon user show User admin Access administrator 0 Timeout 1800 User guest Access guest 0 Timeout 600 4 3 15 6 Change User s Timeout Command epon user timeout name timeout Grammar Exon Change appointed user s timeout time Within the timeout time user unction can t make any operation and log out the system automatically name Change timeout user name with the byte length from 4 to 15 bytes Appointed user s timeout time with the valid index range from 1to timeout M 3600 and unit is second Remark Change user s timeout function which is valid after logging in the system again 4 3 16 VLAN Management Mode Command epon vlan lt vlanid gt Grammar Function Create a vlan and enter vlan management mode for configuration lt vlanid gt Vlan ID to be modified or created with valid value from 1 to 4094 Example 1 Create Vlan100 and enter vlan100 s management mode epontivlan 100 epon vlan100 t epon vlan100 4 input or help to show current directory delete delete vlan members or vlan member add vlan member 80 1N OVERIEK GEPON OLT CLI User Manual 4 3 16 1 Delete Vian Member Command epon vlan100 delete member lt portlist gt Grammar Delete vlan member port Function Input delete member to to d
47. n mode 4 3 10 7 Set Port s RX Filter Function Command epon ge1 ingr filter operator Grammar Configure switch control card port s RX packet filtering function Function When the port is not the vlan member appointed by frame VID the packet is dumped at the time of receiving the frame Enable enable switch control card port s RX frame filter function operator Disable disable switch control card port s RX frame filter function 4 3 10 8 Configure Port Mode Command epon ge1 mode mode Grammar Configure switch control card port s port mode including copper Function and fiber modes Copper copper mode mode fiber fiber mode 4 3 10 9 Enable Port s Nest Vlan Function Command epon ge1 nest vlan operator Grammar Function Configure switch control card port s nest vlan function enable enable port nest s vlan function operator i Disable disable port nest s vlan function 4 3 10 10 Enable Port s Protocol Vlan Command epon ge1 Hprot vlan operator Grammar 64 ILEN OVERIEK GEPON OLT CLI User Manual Function Configure switch control card port s protocol vlan function Enable enable port s protocol vlan function operator i i Disable disable port s protocol vlan function Remark This command s effect is the same as no enable lt portlist gt un
48. nction Test remote host s connection host Remote host s ip address 4 5 14 Show Directory Route Command pwd Grammar Function Show directory route 4 5 15 TFTP Command tftp cmd filename mode Grammar Function Upload download file through TFTP TFTP command cmd get download file 88 GEPON OLT CLI User Manual 1N OVERIEK Put upload file GEPON OLT CLI User Manual lt filename gt File name File format lt mode gt ascii file format binary format 89
49. nd epon slot3 olt1 onu1 fe1 bridge age time age time gt Grammar Function Configure ONU port s Aging time of MAC address age time MAC address aging time with valid value from 0 to 32768 0 means not to age MAC address 4 3 4 7 6 2 4 Configure ONU Port s Forward Mode Command epon slot3 olt1 onu1 fe1 bridge forward mode lt forward mode gt Grammar Function Configure ONU port s forward mode lt forward mode gt 8021d mode unknown MAC packet broadcast to all ports Forward mode with valid value such as 8021d drop until learned Drop until learned mode drop unknown MAC packet 4 3 4 7 6 3 Clear ONU Port s Dynamic MAC List Command epon slot3 olt1 onu1 fe1 dynamic mac clear Grammar Function Clear ONU port s dynamic MAC list 4 3 4 7 6 4 Show ONU Porte Dynamic MAC List Command Grammar epon slot3 olt1 onu1 fe1 dynamic mac list Function Show ONU port s dynamic MAC List 38 1N OVERIEK GEPON OLT CLI User Manual 4 3 4 7 6 5 Enable ONU UNI Port Command epon slot3 olt1 onu1 fe1 enable Grammar Function Enable ONU port to make sure normal communication 4 3 4 7 6 6 Disable ONU UNI Port Command epon slot3 olt1 onu1 fe1 no enable Grammar Function Disable ONU port to stop the data flow communication 4 3 4 7 6 7 Configure ONU Port s User Information Command epon slot3 o
50. nebyone switch control card s uplink port is corresponding with mode PON port corresponding mode such as ge1 ge9 ge2 ge10 ge8 ge16 Trunk port convergence mode When mode is trunk mode that means to converge the uplink net port ports port from ge1 to ge8 4 3 9 2 Show Switch Control Card s Switch Mode Configuration Command epon swmode show Grammar Function Show switch control card s switch mode Example 1 Show switch control card s switch mode configuration information epon swmode show Current basic switch mode vlan unaware Current private vlan mode disabled 60 ILEN OVERIEK GEPON OLT CLI User Manual 4 3 9 3 Enable Switch Control Cards Vlan Function Command epon swmode vlan mode Grammar Function Enable Switch Control Card s Vlan Function aware eable vlan vlan aware mode unaware disable vlan vlan unaware 4 3 10 Uplink Port Management mode of Switch Control Card Command epon swport port Grammar Enter port management mode of switch control card under this Function mode you can configure several index function port Appointed port list any one from gel to ge16 example 1 Enter switch control card s port 1 management mode epon swport gel epon ge1 epon ge1 input or help to show directory acc frame set port access frame type def pri se
51. nnnnrvrnnernnnnnnnnrvvnnrrnnnnnvnnenere 85 Global Command seesnnonnnnrnnonrnnenvnnennnnennrnsnnrnsenrnnernnenrnnenvnnennensnnrnsnnrnsenrnsensenennenennene 85 4 5 1 Create Command Alias enne enne entente nnne 85 4 5 2 Change Directory unen essei Enana deberes dear eaa ie Da a Mila ai Rich 85 4 5 3 Clear SCO ON isis dern red rH ERR eS ERES K KE YER Re P E EEE AAEE 86 4 5 4 CODV He vr 86 4 5 5 Show System s Date 86 1N OVERIEK GEPON OLT CLI User Manual 4 5 6 4 5 7 4 5 8 4 5 9 4 5 10 4 5 11 4 5 12 4 5 13 4 5 14 4 5 15 BI se 86 Exit From The Current Command Mode AA 87 Return to System Main Director 87 ari date 87 Command HISEOEV caeteri ete Eder eunt knee ee e S ERO FEY eei uis 87 Log gl e 87 Show Current File List ecoute a 88 d ce 88 Show Directory A 88 TETP ET EE 88 1N OVERIEK GEPON OLT CLI User Manual 1 Preface 1 1 Introduction Unotrade OLT OT 2000S system could support inband and outband network management mode and EMS network management based on SNMP which we would provide our EMS software along with the parcel for shipping Besides we could also support CLI management for user to get access to our EPON system with more option Herein we would like to introduce our CLE user manual However we would still highly recommend users to
52. nted by the UNI port Frame Type Approach Untagged frame Switch frames on port s default VLAN VPID domain Tagged frame the ONU port is on the vlan domain Switch frames on frame VID s VLAN domain Tagged frame the onu port is not on the vlan domain Ignore the frame Tagged Frame VLAN doesn t Ignore the frame exsit 4 3 4 7 7 1 4 Configure ONU PON Port s PVID Command epon slot3 olt1 onu1 ponport vlan pvid lt vlanid gt Grammar Function Configure ONU pon port s default VLAN ID PVID lt vlanid gt Appoint Vlan ID with valid value range from 0 to 4094 Example 42 M PARS OVERIEK GEPON OLT CLI User Manual 1 Configure ONU UNI port1 s PVID as 100 epon slot3 olt1 onu1 ponport vian pvid 100 4 3 4 7 7 1 5 Show ONU PON port s VLAN configuration Command epon slot3 olt1 onu1 ponport vlan show Grammar Function Show ONU PON port s Vlan configuration information Example 1 Show ONU PON port s VLAN configuration epon slot3 olt1 onu1 ponport vlan show ONU 3 1 1 pon port vlan information pvid 100 forward policy policy3 number of vlans 1 1 vlanid 100 tag modification addtag 4 3 4 7 8 ONU UNI Port VLAN Configuration 4 3 4 7 8 1 1 Add VLAN Command epon slot3 olt1 onu1 fe1 vlan add vlanid lt tagModify gt Grammar Function Add appointed ONU UNI port s VLAN
53. ntrol card s MAC address list of appointed port When unction lt port gt is ignored it will show all ports MAC address i Optional index only show appointed port s MAC address list with port P value range from ge1 to ge16 4 3 2 Port mirror Management 4 3 2 1 Mirror Destination Port Command m epon mirror destination port port gt Grammar Configure the designated port for the switch control card as the Function E mirror destination port Designate a port as the mirror destination port with value range from lt port gt gel to ge8 4 3 2 2 Add Mirror Source Port Command y ANS epon mirror source add port portlist gt direction gt Grammar 16 1N OVERIEK GEPON OLT CLI User Manual Configure added mirror source port available for designating some unction port s uplink downlink or bidirectional data flow as mirror source i Designate some port as mirror source port Designation means could lt port list gt refer to 3 3 Typical Parameter category Illustration Designate mirror source s data flow direction with vale as follows I ingress direction egress both 4 3 2 3 Delete Mirror Source Port Command 1 TEM epon mirror source delete port lt portlist gt lt direction gt Grammar Delete mirror source port which could appoint one direction s data Function flow as mirror source
54. olt1 link1 show Link Basic Configurations associated onu id 1 assigned link id by olt 0 mac address 00 a1 02 0a a1 08 online status Online key exchange timer 0 sec bridging type simple bridge mac table entry limit 64 entries cross connected link id NO 4 3 4 6 8 Link SLA Configuration 4 3 4 6 8 1 Configure Link s Minimum Guaranteed Bandwidth Command epon slot3 olt1 link1 sla lt dir gt min bw lt min bw gt Grammar Configure the link s uplink or downlinks minimum guaranteed Function bandwidth Appoint the link sla s direction dir downstream upstream Appoint the link s minimum guaranteed bandwidth with valid min bw value from 0 256 to 1000000 0 means disabling the minimum guaranteed bandwidth function Remark The minimum bandwidth much be lower than or equal to the maximum allowed bandwidth 4 3 4 6 8 2 Configure Link s Maximum Allowed Bandwidth Command y epon slot3 olt1 link1 sla dir max bw lt max bw gt Grammar 28 LAN OVERIEK GEPON OLT CLI User Manual Configure the link s uplink or downlink maximum allowed Function bandwidth Appoint the link SLA s configuration direction lt dir gt downstream upstream Appoint the link s maximum allowed bandwidth with valid value lt max bw gt from 256 to 1000000 0 means disabling the minimum guaranteed bandwidth function Remark
55. on Add a user name User name with the length from 4 to 15 bytes Optional index to change new password if there is no index the passwd user s password is blank if index is provided it could be any obvious bytes combination with the length from 6 to 31 bytes admin administer who has all the configuration and operation access rights 78 1N OVERIEK GEPON OLT CLI User Manual Guest guest who could only ready the operation Configuration 4 3 15 3 Delete User Command epon user delete lt name gt Grammar Function Delete appointed user from logging in the system Appoint the user name to be deleted with the bytes length from 4 to lt name gt 15 Remark Only the system s administer the user priority level is 1 has the rights to add and delete system users 4 3 15 4 Change User Password Command epon user passwd name lt password gt Grammar 8 Change appointed user s log in password Function e i If lt password gt is ignored the log in password is blank lt name gt User name with the bytes length from 4 to 15 bytes Optional index to input new password password If the index is not provided the password is blank if the index is provided the password length can be from 6 to 31 bytes 4 3 15 5 Show Current User s Information Command epon user show Grammar Function Show system s all user list Exa
56. ould only bind only one Function VLAN ID Different protocols could bind the same VLAN ID Only the protocol in the protocol pool could be used to bind port protocol vlan lt portlist gt Appointed port list from ge1 to ge16 Appoint the bonded protocol type with hex based Ox as prefix such as lt protocol type gt 0x0800 0x0806 or the regular protocol name bytes value The current protocol name only support ip arp and pppoe vlanid Appoint the bonded VLAN ID with integer value from 1 to 4094 Example 1 Confiugre ip protocol to vlan2000 in port gel epon prot vilan bind ge1 ip 2000 4 3 6 5 Remove Bind Rule Command epon prot vlan no prot vlan bind portlist protocol type Grammar Function Remove protocol vlan bind rules in the appointed port portlist Appointed port list which could be anyone from gel to ge16 protocol type Appoint the bonded protocol type to be removed with hex based Ox as prefix such as 0x0800 0x0806 or the regular protocol name bytes value The current protocol name only support ip arp and pppoe 52 1N OVERIEK GEPON OLT CLI User Manual 4 3 6 6 Enable Port Protocol VLAN Function Command epon prot vlan enable lt portlist gt Grammar Enable appointed port s protocol based vlan function only enable the Function port s protocol based vlan function could make the port protocol vlan bind rules valid portlist Appoin
57. rmation Command epon rstp show Grammar Function Show RSTP bridge and port s configuration information Example 1 show switch control card s RSTP configuration information epon rstp show RSTP Bridge Status RSTP Setting Enable Bridge ID PRI MAC 32768 00 a1 02 22 11 89 Bridge Hello Time 2 sec Bridge Max Age 20 sec Bridge Forward Delay 15 sec Transmit Hold Count 6 Root Bridge ID 32768 00 a1 02 22 11 89 Root Path Cost 0 RSTP Port Status PID Mode Pri PathCost EdgeCfg OperEdge P2PCfg OperP2P State 1 RSTP 128 20000 Auto Non Edge Auto Shared LinkDown 2 RSTP 128 20000 Auto Non Edge Auto Shared LinkDown 3 RSTP 128 20000 Auto Non Edge Auto Shared LinkDown 4 RSTP 128 20000 Auto Non Edge Auto Shared LinkDown 5 RSTP 128 20000 Auto Non Edge Auto Shared LinkDown 6 RSTP 128 20000 Auto Non Edge Auto Shared LinkDown 7 RSTP 128 20000 Auto Non Edge Auto Shared LinkDown 8 RSTP 128 20000 Auto Non Edge Auto Shared LinkDown Total 8 RSTP ports dumped 59 1N OVERIEK GEPON OLT CLI User Manual 4 3 9 Configure Switch Control Card s Switching Mode 4 3 9 1 Set Private Vian Mode Command epon swmode pve mode lt net port gt Grammar Function Configure private vlan mode for uplink port of switch control card Private vlan mode disable onebyone trunk gt disable normal switch mode where the uplink port of switch control card doesn t has VLAN limitation O
58. rotocol by means of hex based protocol number epon prot vian add prot type 0x8863 2 Add ip protocol based on protocol name epon prot vian add prot type ip 4 3 6 2 Delete Protocol Command epon prot vlan delete prot type lt protocol type gt Grammar delete a protocol from the globalallowed protocol pool Only the protocol added to the protocol pool can bind the port protocol vlan Function When a protocol is deleted all protocol s bind rules are deleted at the same time If the protocol to be deleted is not in the protocol pool no need to take any actions but the protocol is still valid Appoint deleted protocol type with valid value hex based Ox as prefix or protocol name s bytes series common protocol name could only lt protocol type gt support ip arp and pppoe such as 0x8863 pppoe etc 4 3 6 3 Clear Protocol Pool Command epon prot vlan itclean Grammar Clear globalallowed protocol pool and all port protocol vlan bind Function rules are deleted at the same time You need to add new protocol and bind rules when protocol based vlan is needed 51 es OVERIEK GEPON OLT CLI User Manual 4 3 6 4 Add Bind Rule Command epon prot vlan prot vlan bind lt portlist gt protocol type lt vlanid gt Grammar Create protocol vlan bind rule for the appointed port The bind rule is based on port so the same port s protocol c
59. runk module 16 mirroring module 17 normal vlan module 18 protocol type based VLAN 19 rapid spanning tree module 20 IP network interface 21 misc configuration on switch card 22 ONU base manage configuration 23 ONU advanced manage configuration 24 ONU UNI port configuration 25 ONU Queue configuration 26 ONU ACL Rules configuration 27 ONU port VLAN configuration 28 ONU authentication 29 ONU port QoS configuration 30 ONU IGMP Snooping configuration 31 ONU loopback test configuration 32 ONU dynamic mac table configuration 33 Extern network management module 34 OLT basic configuration 35 OLT advanced configuration 36 OLT bridge configuration 37 OLT DBA configuration 38 OLT aggregate bandwidth configuration 39 OLT acl rules configuration 40 OLT priority copy mapping configuration 41 OLT IGMP configuration 42 OLT PPPOE configuration 43 Logical Link basic configuration 44 Logical Link advanced configuration 45 Logical Link SLA configuration 46 Logical Link VLAN configuration 47 Logical Link blocked link configuration 48 Logical Link dynamic and static MAC 50 on line upgrade module 51 port statistics alarm and threshold 12 1N OVERIEK GEPON OLT CLI User Manual 4 System Root Directory Ater you log in successfully input or help to show the current directory epon no copy log print log messages on the current shell debug enter debug mode enable enter privileged mode exe Execut
60. s with longest bytes 64 4 3 4 7 4 ONU Link Loopback Test Command epon slot3 olt1 onu1 loopback test Grammar Test ONU link status and this command is interactive command which need the user to provide the following Parameterstep by step loopback location mac 3 phy Function number of frames 1 65535 payload length 64 1500 vlan tag 0 4094 Example 1 Test ONU Link epon slot3 olt1 onu1 loopback test please offer the loopback test parameter loopback location mac phy mac number of frames 1 65535 100 payload length 64 1500 64 vlan tag 0 4094 0 testing result frames sent 100 frames received 100 corrupted frames receiv 0 minimum Delay us 2512 34 ILEN OVERIEK GEPON OLT CLI User Manual maximum Delay us 5788 mverage Delay us 4135 4 3 4 7 5 Show ONU Dynamic MAC Address List Command epon slot3 olt1 onu1 mac address show Grammar Function Show ONU s dynamic learning MAC address gloably 4 3 4 7 6 ONU Port Management Mode Command R epon slot3 olt1 onu1 port uni port gt Grammar Enter ONU port management mode and configure the ONU port s Function Parameter uni port Appoint onu port number with valid value range from fe1 to fe8 Example 1 Enter ONU1 s port 1 interface epon slot3 olt1 onu1 port fe1 epon slot3 olt1 onu1 fe1 epon slot3 olt1 onu1 fe1 input or help to s
61. sable Grammar Function Enable disable OLT enable Enable OLT disable Disable OLT 4 3 4 3 OLT Bridge Configuration Command epon slot3 olt1 bridge Grammar Function Show current bridge setting example 1 Show OLT s current bridge setting epon slot3 olt1 bridge Bridge Configuration learned mac age limit 0 ms bridge vlan number 64 bridges allow simple bridge YES mac learn overwrite NO discard unknown mac NO allow tagged frame Y YES 21 ILEN OVERIEK GEPON OLT CLI User Manual 4 3 4 3 1 MAC Address Aging Time Command C epon slot3 olt1 bridge limit limit Grammar Change MAC address s aging time 0 means not to learn MAC the Function unit is 1ms limit Parameterrange 0 2516582400 about 29 days 4 3 4 3 2 Bridge VLAN Number Configuration Command epon slot3 olt1 bridge vlan num vlanNum Grammar Function Set bridge vlan number tk3723 chipset OLT s fixed number is 64 vlanNum Fix number is 64 4 3 4 3 3 MAC Address Overwrite Configuration Command epon slot3 olt1 bridge overwrite enable disable Grammar Function Set overwrite MAC address mode Parameters enable disable gt with the meaning as follows enable When MAC address is full new MAC overwrite existing MAC address disable When MAC address is full ignore the new MAC address enable disable 4
62. t port Grammar 23 1N OVERIEK GEPON OLT CLI User Manual Configure management host s IP and UDP port GEPON system Be receive the management UDP packet from the management IP and unction UDP port and deliver the responded packet back to the management IP and UDP port lt ip add gt Configure management host s IP address Configure management host s management UDP port number with port P the value range from 0 to 65535 Example 1 Configure management host IP as 192 168 120 1 port as 14115 epon slot3 olt1 ext mgmt host 192 168 120 1 14115 4 3 4 5 2 Configure OLT s management Port Command epon slot3 olt1 ext mgmt mgmt port port Grammar Configure OLT s UDP management port where the OLT process and Function respond the management packet Configure management host s UDP port with value range from O to 65535 OLT s default management port as follows OLT1 slot1 14113 OLT2 slot2 14114 OLT3 slot3 14115 OLT4 slot4 14116 4 3 4 5 3 Enable Disable OLT s UDP Management Function Command epon slot3 olt1 ext mgmt enable disable Grammar Function Enable disable OLT s UDP management port enable disable enable enable OLT UDP management function 24 oN OVERIEK GEPON OLT CLI User Manual disable Disable OLT s UDP management function 4 3 4 5 4 Show OLT s UDP Management Information
63. t port default priority duplex set port duplex no enable set port enable flow ctrl set port flow control ingr filter set port ingress filter mode set port mode nest vlan set port nest vlan enable or disable prot vlan set port protocol based vlan enable or disable pvid set port pvid 61 1 OVERIEK rate ctrl reautonego show no shutdown speed set port ingress rate limit parameters set port reautonegotiation show port attribute information shut down a port set port speed 4 3 10 1 Set Port s RX Frames Types Command epon ge1 acc frame lt type gt Grammar Function Set switch control card port s RX packet frame types Packet frame types tagged receive tagged packet only lt type gt f untagged receive untagged packet only all receive all types of packet frame Remark Our OTL system can t set untagged type mode yet 4 3 10 2 Set Port s Default Priority Level Command epon ge1 def pri privalue gt Grammar Set switch control card s default priority level similar to PVID When port received untagged vlan packet the packet is set by priority The Function priority level is port s default 802 1P priority The data packet will enter different priority queue to receive different service according to corresponding priority level and flow category privalue Set configured port s priority level value from 0 to 7 4 3 10 3 Configure
64. ted port is point to point port Point to point port could allow to switch Function to forward status rapidly Non point to point port needs to go through step of discarding learning forwarding first before switching to forward status lt portlist gt Port list from gel to ge8 f Appointed RSTP port index with bytes value such as p2p shared and p2p i auto 4 3 8 5 4 Set RSTP Port s Link Cost Command epon rstp port lt portlist gt path cost lt pathcost gt Grammar Configure RSTP port s link cost It s used to calculate the root link s Function cost The port with the lowest root link cost will change to forward port when delivering the same bridge ID portlist Appointed port list any one from ge1 to ge8 Appointed RSTP port s link cost with integer value from 1 to pathcost 200000000 4 3 8 5 5 Set RSTP Port s Priority Level Command epon rstp rstp port lt portlist gt priority priority Grammar Configure RSTP port s priority level The port with priority will change Function to forward port when delivering the same bridge ID and having the same link cost portlist Port list any one from gel to ge8 58 1N OVERIEK GEPON OLT CLI User Manual Configure appointed RSTP port s priority level with integer value valid lt priority gt from 1 to 240 step length 16 meaning 16xN n is from 0 to 15 4 3 8 6 Show RSTP Configuration Info
65. ted port list which could be any one from ge1 to ge16 Example 1 Enable port ge1 ge2 ge3 and ge6 s protocol based vlan function epon prot vlan enable ge1 ge3 ge6 4 3 6 7 Disable Port Protocol VLAN Function Command epon prot vlan no enable lt portlist gt Grammar Disable appointed port s protocol based vlan function After disabling Function port s protocol based vlan port protocol vlan s bind rules become invalid lt portlist gt Appointed port list which could be any one from ge1 to ge16 4 3 6 8 Show Protocol VLAN s Configuration Information Command epon prot vlan show Grammar Function Show protocol based vlan s configuration information example 1 Show protocol based vlan s configuration information 53 1N OVERIEK GEPON OLT CLI User Manual epon prot vlan itshow Enabled protocols 1 8863h pppoe 2 0800h ip Protocol based VLAN on ge1 is enabled Configured protocols 0800h ip bind to vlan 2000 Protocol based VLAN on ge2 is enabled Protocol based VLAN on ge3 is enabled Protocol based VLAN on ge4 is disabled Protocol based VLAN on ge5 is disabled Protocol based VLAN on ge6 is enabled Protocol based VLAN on ge7 is disabled Protocol based VLAN on ge8 is disabled Protocol based VLAN on ge9 is disabled Protocol based VLAN on ge10 is disabled Protocol based VLAN on ge11 is disabled Protocol based VLAN on ge12 is disabled Protocol based VLAN on
66. tem s Current CPU Running Status Command epon gt show cpu Grammar Function Show system s CPU running status information Example 1 Show system s CPU Running Information epon gt show cpu NAME ENTRY TID PRI total ticks delta ticks tlobTask Oxd19a4 Ox8ac158 0 0 0 0 0 mTrAging 0x43975c 0xf7c350 5 0 0 0 0 tErfTask Oxb46bc 0x8b5a30 10 096 0 0 0 intSchedO 0x31a72c OxfOb5eO0 10 096 0 0 0 intSched1 0x31a72c Oxf16880 10 0 0 m i 0 tNetTask Ox363cO 0x945d00 40 0 0 0 0 tlbcpPoll Ox13dc7c 0x1243cd0 45 0 0 0 0 tlbcpRx 0x13e74c 0x1241338 46 13 2 13 2 tXbdService OxccbaO 0xa1af80 50 0 0 0 0 tFtp6d Ox2f97c Oxa16efo 56 0 0 mi 0 tUserLog 0x16a9cO Oxf826a8 60 0 0 0 0 tUpgradeTask 0x167174 0x1348aa8 64 0 0 0 0 KERNEL 0 0 0 0 INTERRUPT 0 0 IDLE 86 13 86 13 TOTAL 99 15 99 15 4 4 2 Show System s Memory Use Status Command epon gt show mem Grammar 83 1N OVERIEK GEPON OLT CLI User Manual Function Show system s memory use status information Example 1 Show system s current memory user information epon show mem status bytes blocks avg block max block current free 12695080 4 3173770 12681624 alloc 12055336 1185 10173 internal 408 2 204 cumulative alloc 12702512 1795 7076 peak alloc 12059424 4 4 3 Show System s Task Status
67. vlan domain and ignore frame VID Frame Type Approach Untagged Frame Switch frames on default vla PVID n domain Tagged Frame Ignore frame s VID treated as untagged frame 44 ZN OVERIEK GEPON OLT CLI User Manual 6 policy1 Switch VID frame unknown VID treated as untagged Frame Type Approach Untagged frame Switch frames on port s default Vlan domain Tagged frame the ONU port is on the vlan domain Switch frames on frame VID s VLAN domain Tagged frame the onu port is not on the vlan domain Switch frames on port s default VLAN PVID domain Tagged Frame VLAN doesn t exsit Switch frames on port s default VLAN VPID domain 7 policy2 switch VID frame and ignore unkown VID frames Frame Type Approach Untagged frame Switch frames on port s default VLAN VPID domain Tagged frame the ONU port is on the vlan domain Switch frames on frame VID s VLAN domain Tagged frame the onu port is not on the vlan domain Tagged Frame VLAN doesn t exsit add the port to the VLAN domain temporialy and forward frames on fram VID s VLAN domain Ignore the frame 8 policy3 switch VID frames on the vlan domain appointed by the PON port Frame Type Approach Untagged frame Switch frames on port s default VLAN VPID domain Tagged frame the ONU port is on the vlan domain Switch frames on frame VID s VLAN domain Tagged
68. write Function Command epon slot3 olt1 overwrite onuid lt oper gt Grammar Whether new authorized ONU overwrites the existing ONU ID after Function the ONU ID is set Enable new ONU overwrites existing ONU ID soper Sei Disable new ONU doesn t overwrites existing ONU ID 4 3 4 10 Reboot PON Card Command epon slot3 olt1 reboot Grammar Function Reboot PON card 4 3 4 11 Save PON card configuration Command epon slot3 olt1 save Grammar Function Save PON card s all configuration 48 ILEN OVERIEK GEPON OLT CLI User Manual 4 3 4 12 Show OLT s Basic Information Command epon slot3 olt1 show Grammar Function Show OLT s basic configuration Example 1 Show OLT s current basic configuration epon slot3 olt1 show Olt Basic Configurations mac address 00 0d b6 37 23 00 work state Online enable status Enable max permitted link number 210 registered link number 1 accessed onu number 1 link id exhausted NO onu id exhausted NO link id overwrite NO onu id overwrite NO 4 3 5 Configure Enable Password Management Command epon passwd Grammar Function Enter the enable password changing mode Example 1 Change enable password epon passwd Enter new enable password Confirm new enable password 49 1N OVERIEK GEPON OLT CLI User Manual epon Remark Ple
69. xage maxage gt Grammar 55 es OVERIEK Configure RSTP bridge s maximum valid age which is the valid time for Function n i receiving BPDU packet from appointed port s bridge Value range 6 40 must demand the following bind relation 2x ForwardDelay 1 0second gt MaxAge lt maxage gt MaxAge is bridge infomration s maximum valid time ForwardDelay forward delay 4 3 8 1 3 Bridge Priority Command epon rstp bridge priority lt priority gt Grammar Function Set RSTP bridge priority 2 Appointed bridge priority integer value from 1 to 61440 and step priority length is 4096 meaning 4096xN N is from O to 15 4 3 8 2 Enable RSTP Function Command epon rstp enable Grammar Function Enable switch control card s uplink port s RSTP function Example 1 Enable switch control card s uplink port s RSTP function epon rstp enable 4 3 8 3 Disable RSTP Function Command epon rstp disable Grammar Function disable switch control card s uplink port s RSTP function 56 GEPON OLT CLI User Manual es OVERIEK 4 3 8 4 Hold Bridge Forwarding Frame Count Command epon rstp hold count lt holdcount gt Grammar Configure RSTP s deliving BPDU packet limit and appoint the Function maximum delivering BPDU packet within 1 second lt holdcount gt Value range from 1 to 10 4 3 8
70. y actions ASAP the shutdown port function is recommended 4 3 10 16 Remove Compulsive Shutdown Port Command Grammar epon ge1 no shutdown 67 1N OVERIEK GEPON OLT CLI User Manual Remove switch control card port s compulsive shutdown function In Function an exceptional case such as attached by virus or hacker and can t take any actions ASAP the shutdown port function is recommended 4 3 10 17 Configure Current Port Rate Command epon ge1 speed speed Grammar Configure switch control card port s speed Under fiber port mode the Beate port could only work at the speed of 1000Mbps Under the copper unction port mode the port can work at different speed and available for auto negotiation function configuration 10m 10mbps 100m 100mbps 1g 1gbmp 1000mbps 10g 10gbps Auto auto negotiation speed 4 3 11 System Configuration Mode Command epon system Grammar Function Enter GEPON system s management mode Example 1 Enter system management mode epon system epon sys epon sys input or help to show current directory cfg sync synchronize onu config with its config file console configure console parameters onu auth configure ONU authentication parameters read comm set snmp read community string reboot reboot the system 68 oN OVERIEK GEPON OLT CLI User Manual restore restore to saved conf
71. zation all ONU could be authorized 72 1N OVERIEK GEPON OLT CLI User Manual 4 3 12 5 Set SNMP Read Community Command epon sys read comm lt community gt Grammar Function Set EMS software SNMP s read community Read community with bytes serial the longest length couln t be over community 26 bytes such as public 4 3 12 6 Reboot OLT Command epon sys reboot device slot olt onu Grammar Reboot EPON device This command will reboot switch control card R some PON card some ONU or the equipment under the EPON Function system Input command reboot will only reboot the switch control card Appoint the device to be rebooted with following index ctrl card reboot switch control card lt slot gt lt olt gt onu is ignored pon card reboot appointed pon card with index slot device olt onu is ignored Onu reboot appointed onu under the index slot olt onu all reboot the whole EPON system including OLT and ONU lt slot gt lt olt gt onu is ignored slot Appoint PON card s slot number with valid value from 1 to 4 it Appoint PON port number under a pon card slot with valid value olt from 1to2 onu Appoint ONU number with valid value from 1 to 64 Example 1 Reboot switch control card epon sys reboot Or 73 1N OVERIEK GEPON OLT CLI User Manual epon sys r

GEPON OLT OT-2000S CLI User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents