USER MANUAL
Contents
1. ed 2 INSTAEEATI N Gallia 3 FUNCTIONAL TES es pes ee Ge oe ee ate 5 INTERFACE CONNECTION ii 8 SOFTWARE COMMANDS keine eneren he vn 10 HARDWARE CONFIGURATION in 11 DISPLAY CHARACTER CODES Mi er Se es es pe es 12 GENERAL SPECIFICATIONS sesse ee se ee ee ee ee ee ee ee ee ie 13 iii FEATURES The LD9000 family of pole displays offers a wide range of high quality features and models to choice from Listed below are the features incorporated into each pole display Not all features are available in all models The model identification chart will assist you in selecting the model best suited to your needs Features All Models Bright blue green fluorescent display Large 9mm character height Double sided display available Supports high speed serial protocol up to 19 200 baud rate 1 stop bit Automatic message scrolling Two line display with 20 characters per line Matched optical lens for better viewing contrast Ergonomic design Direct RS232C or parallel interface Long life and trouble free operation Five adjustable viewing angles Simple installation Available with 120V or 220V Power Adapters Features Model dependent Emulation of other popular command sets Double sided display User definable character Parallel pass thru True RS232C pass thru Real time clock One time message scrolling Ability to disable attention code Ability to change attention code MODEL IDENTIFICATI2. tied to pins 1 amp 6 Ground DSR tied to pins 1 amp 4 DB9F to computer RTS tied to pin 8 CTS tied to pin 7 NC a Lo AT ME For pass through models the display cable comes with two connectors The DB9F is to be connected to the computer while the DB25M is for connection to the peripheral DCD tied to pins 486 TXD to PC RXD from PC DTR tied to pins 1 amp 6 Ground DSR tied to pins 1 amp 4 DB9F to computer RTS tied to pin 8 CTS tied to pin 7 NC SS BED GENE NC TXD to peripheral RXD from peripheral 13 RIS Sor CTS tied to pin 20 NC Ground i NC DB25M to peripheral 9 19 NC 20 DTR tied to pin 5 21 25 NC ONDIN Parallel Interface Connector Configuration All standard parallel pole displays will have a DB25 male connector It is connected to the printer port of the computer Strobe Data 0 Data 1 Data 2 Data 3 3 Data4 ERE REE Data 5 Data 6 DB25M to computer Data 7 Ack 11 Busy 12 17 NC 18 25 Ground O70 SLO ng For pass through models the display cable comes with a dual DB25M F connector The DB25M is to be connected to the computer while the DB25F is for connection to the peripheral 1 Strobe 2 Data 0 3 3 Daal lt lt Ls 2 FRESKER DDR 2 Data Gress 5 Data 3 i 6 Data 4 DB25M to computer 7 Data 5 8 Data 6 9 Data 7 10 Ack 11 Busy 12 Paper End 13 Select l 14 Auto Feed DB25F to peripheral 1
3. 5 Error 16 Initialize Printer 17 Select In 18 25 Ground SOFTWARE COMMANDS Logic Controls pole displays are controlled by command codes and data from the computer The model of pole display that you have will determine which command set works with your pole Refer to the model identification chart for further information For Logic Controls Command Sets call 516 248 0400 or e mail support logiccontrols com 10 HARDWARE CONFIGURATION Serial pole displays were factory configured for serial RS232C interface using the following protocol 9600 Baud Rate 8 Data Bits 1 Stop Bit No Parity Other optional baud rates are available with factory settings Refer to the model identification chart for further information 11 DISPLAY CHARACTER CODES kN NNN clelia ka se SE sie EGE 12 GENERAL SPECIFICATIONS LD9000 LD9000X OPTICAL Number of rows 2 2 x 2 sides Number of digits row 20 20 Dot matrix 5x7 5x7 Digit height 0 374in 9 5mm 0 374in 9 5mm Digit width 0 244in 6 2mm 0 244in 6 2mm Character config ASCII ASCII Brightness typical 900 cd m 900 cd m Display color Blue Green Blue Green MTBF hours 300 000 300 000 MECHANICAL Weight 2 7 Ib 2 7 Ib Dimensions in inches w x h x d w x h x d Display head 8 50 x 3 37 x 1 75 8 50 x 3 37 x 1 75 Rectangular base 2 12 x 2 0 x 2 25 2 12 x 2 0 x 2 25 Base plate 4 0 x 0 09 x 8 0 4 0 x 0 09 x 8 0 Overall height typical 24 24 ELECTRIC
4. AL Adapter input power Adapter output power 120VAC 60Hz optional 220VAC 50Hz 7 5VAC 1000mA ENVIRONMENTAL Operating temperature 0 to 50 C Storage temperature 20 to 70 C Relative Humidity 80 non condensing Vibration 10 to 55 Hz 4G s Shock 40G s CABLES amp CONNECTORS Serial Display cable 8 pin Mini DIN male Interface cable Power adapter Parallel Display cable 8 pin Mini Din female DB9 female optional DB25 female Phone jack male Phone jack female DB25 female 13
5. Models LD9000 Series Customer Displays 2 by 20 character display USER MANUAL ILOGIC CONTROLS NOTICE The manufacturer of the POS pole display makes no representations or warranties either expressed or implied by or with respect to anything in this manual and shall not be liable for any implied warranties of fitness for a particular purpose or for any indirect special or consequential damages Information in this document is subject to change without notice and does not represent a commitment on the part of the manufacturer FCC NOTICE This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with this manual may cause interference to radio communications It has been tested and found to comply with the limits for a Class A digital device pursuant to Subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference LOGIC CONTROLS INC 355 Denton Avenue New Hyde Park NY 11040 TEL 516 248 0400 FAX 516 248 0443 Email Ici Qlogiccontrols com http www logiccontrols com TABLE OF CONTENTS FEATURES orden 1 MODEL IDENTIFICATION 2 CARTON CONTENTS 2de oe ke ee RE
6. ON LD9 ___ pa X Double Sided Display PT Pass Thru 25 DB25F connector to computer rain ADAPTER 120VAC COMMAND SET 1 220VAC 0 LOGIC CONTROLS 1 LOGIC CONTROLS SERIAL PARALLEL INTERFACE WITH PASS THRU 0 SERIAL 9600 BAUD 2 SPECIAL COMMAND SET 1 Aedex emulation 1 SERIAL 600 BAUD 3 SEPCIAL COMMAND SET 2 Noritaki emulation 2 SERIAL 1200 BAUD 4 SPECIAL COMMAND SET 3 Epson D202 emulation 3 SERIAL 2400 BAUD 5 SPECIAL COMMAND SET 4 Ultimate PD1100XL XLT 4 SERIAL 4800 BAUD 9 OPOS COMMAND SET 5 SERIAL 19200 BAUD 9 PARALLEL INTERFACE ann nanan Default Values Call for description of Command Sets CARTON CONTENTS Pole display pre assembled 2 Interface cable comes with a DB9F connector to computer and a Mini DIN8F connector to pole display as standard equipment Optional DB25F connector to computer is available Note This cable is only supplied with standard serial pole displays with no pass thru function Other interface options will have different cables 3 Transformer adapter 120VAC to 7 5VAC optional 220VAG Metal base plate with mounting hardware 5 Quick Installation Guide INSTALLATION Your LD9000 family of pole displays has been pre assembled to make the installation as simple as possible Serial Interface Non pass thru Models Installation 1 2 Mount the pole display to the metal base plate using the mounting hardware provided The pole disp
7. ay will show ABCDEFGH on the first line 2 To endthe test press Ctrl C hold down Ctrl and press C LD9100 PT LD9300 PT LD9400 PT and LD9900 PT 1 2 Type ABCDEFGH and press ENTER key The display will show ABCDEFGH on the first line Type AAPASSTHRU AA is entered as Ctrl A and press ENTER key The data will be passed through to the peripheral e g a printer These characters are not shown on the display Type ABNUMBER12345 AB is entered as Ctrl B then press ENTER key The display will show NUMBER12345 on the first line To end the test press Ctrl C hold down Ctrl and press C LD9200 PT 1 2 Type 1ABCDEFGH and press ENTER key The display will show ABCDEFGH on the first line Type PASSTHRU and press ENTER key The data will be passed through to the peripheral e g a printer These characters are not shown on the display Type 1NUMBER12345 then press ENTER key The display will show NUMBER12345 on the first line To end the test press Ctrl C hold down Ctrl and press C Parallel Interface Pole Displays Functional Test This procedure assumes the pole display is connected to the LPT1 port of the computer If parallel port LPT2 is being used type LPT2 where LPT1 is called out LD9090 LD9390 LD9490 LD9590 and LD9990 1 Type ECHO ABCDEFGH gt LPT1 and press ENTER key The display will show ABCDEFGH on the first lin
8. e LD9290 1 Type ECHO 1ABCEDFGH gt LPT1 and press ENTER key The display will show ABCDEFGH on the first line LD9190 PT LD9390 PT LD9490 PT and LD9990 PT 1 Type ECHO ABCDEFGH gt LPT1 and press ENTER key The display will show ABCDEFGH on the first line 2 Type ECHO AAPASSTHRU gt LPT1 AA is entered as Ctrl A and press ENTER key The data will be passed through to the peripheral e g a printer These characters are not shown on the display Type ECHO ABNUMBER12345 gt LPT1 AB is entered as Ctrl B then press ENTER key The display will show NUMBER12345 on the first line LD9290 PT 1 Type ECHO 1ABCEDFGH gt LPT1 and press ENTER key The display will show ABCDEFGH on the first line 2 Type ECHO PASSTHRU gt LPT1 and press ENTER key The data will be passed through to the peripheral e g a printer These characters are not shown on the display Type ECHO 1NUMBER12345 gt LPT1 then press ENTER key The display will show NUMBER12345 on the first line For further testing of OPOS displays LD9900 and LD9990 follow the instructions in the readme doc file after software installation INTERFACE CONNECTION Serial Interface Connector Configuration The pin out configuration for the standard serial pole display is a DB9F connector It plugs directly into the serial port of the computer DCD tied to pins 4 amp 6 NC TXD from PC DTR
9. isplay can be used in a freestanding mode or attached to the counter using the remaining mounting hardware 3 Connect the DB25M connector to the peripheral device or a serial pass thru terminator optional accessory Turn on power of the peripheral device 4 Connect the DBYF connector to the computer s serial COM1 or COM port 5 Connect the female phone jack of the power adapter to the male phone jack of the pole display cable 6 Plug the power adapter into a 120VAC outlet 7 A start up text message LOGIC CONTROLS POS COMPONENTS will be present for a short time When this message disappears the cursor will be displayed at the left most digit of the top row Parallel Interface Pass thru Models Installation 1 Mount the pole display to the metal base plate using the mounting hardware provided 2 The pole display can be used in a freestanding mode or attached to the counter using the remaining mounting hardware 3 Connect the DB25F connector to the peripheral device or parallel pass thru terminator optional accessory Turn on power of the peripheral device 4 Connect the DB25M connector to the computer s parallel printer port LPT1 5 Connect the female phone jack of the power adapter to the male phone jack at the DB25M DB25F connector 6 Plug the power adapter into a 120VAC outlet 7 A start up text message LOGIC CONTROLS POS COMPONENTS will be present for a short time When this message disappears the cursor will be displa
10. lay can be used in a freestanding mode or attached to the counter using the remaining mounting hardware Connect the round Mini DIN8M connector from the pole display to the round Mini DIN8F connector of the interface cable Connect the DBYF connector to the computer s serial COM1 or COM port Connect the female phone jack of the power adapter to the male phone jack of the interface cable Plug the power adapter into a 120VAC outlet A start up text message LOGIC CONTROLS POS COMPONENTS will be present for a short time When this message disappears the cursor will be displayed at the left most digit of the top row Parallel Interface Non pass thru Models Installation 1 2 Mount the pole display to the metal base plate using the mounting hardware provided The pole display can be used in a freestanding mode or attached to the counter using the remaining mounting hardware Connect the DB25M connector to the computer s parallel printer port LPT1 Connect the female phone jack of the power adapter to the male phone jack of the pole display cable Plug the power adapter into a 120VAC outlet A start up text message LOGIC CONTROLS POS COMPONENTS will be present for a short time When this message disappears the cursor will be displayed at the left most digit of the top row Serial Interface Pass thru Models Installation 1 Mount the pole display to the metal base plate using the mounting hardware provided 2 The pole d
11. yed at the left most digit of the top row FUNCTIONAL TEST The following test sequence will verify that your pole display is working properly Before you start this procedure you must install the pole display correctly as outlined under the INSTALLATION section The functional test should be done under MSDOS command prompt by booting up the computer in DOS mode or shell out to DOS prompt in window95 98 ME or COMMAND prompt in windows NT 2000 For double sided displays the messages will be shown on both sides at the same time NOTE The actual key entries in the text below are enclosed within quotation marks Do not type the quotation marks as part of your entries Serial Interface Pole Displays Functional Test This test procedure assumes the pole display is connected to COM of the computer If COM2 is being used type COM2 where COMI is called out Close all opened application programs that use the same COM port before going into DOS command prompt Enter the following command lines to open the COM port for communication with the pole display Type MODE COM1 96 N 8 1 and press the ENTER key Type TYPE CON gt COM1 and press the ENTER key LD9000 LD9300 LD9400 LD9500 and LD9900 1 Type ABCDEFGH and press ENTER key The display will show ABCDEFGH on the first line 2 To end the test press Ctrl C hold down Ctrl and press C LD9200 1 Type 1ABCDEFGH and press ENTER key The displ
Download Pdf Manuals
Related Search