Home

USER MANUAL - Rohde & Schwarz

1. 3rd Issue 04 09 3rd Issue 04 09 High Speed Digital Test Module R amp S TS PHDT amp SCHWARZ 5 16 Configuration of clock signals The following clock signals are available on the front connector Funktionsbeschreibung Signal name Meaning of polarity active high STIM_CLK A new pattern is generated with the rising edge of this signal If stim ulus formatting is turned off the pattern appears immediately on the outputs AUX_CLK If stimulus formatting is activated for an output this clock determines the time for which a High level is generated RESP_CLK The inputs are sampled with the rising edge of this signal Table 5 10 Clock signals on the X 10 The time response of the clock outputs is configured by time settings for stimulation and data recording The polarity of the clock signals can be set individually with function rsphdt ConfigureClockPolarity NOTE Propagation delay times and rise times in the output driver cause delays in signal change on the outputs compared to clock signal edges 5 17 Synchronising multiple modules Multiple R amp S TS PHDT modules can be synchronised with each other to increase the number of output and input channels All modules are synchronised to a PXI trigger signal trigger signal either can be generated externally or by one of the R amp S TS PHDT modules 5 23 ROHDE amp SCHWARZ Funktionsbeschreibung
2. Execution Results Error List Pattern Index Number failed Result Status Fail Failed Channels Leer Stimulus Execution Start Index Jo Reference Execution Start Index Jo Reset Failed Counter Stop on First Fail tiate n Stimulus State Stopped Auto Increment Start Index Send Trigger Response State Stopped S En Wall Static 1 0 Stimulus Data Static 1 0 Response Data fo Set Output Read Input Figure 7 1 Soft Panel R amp S TS PHDT ILS NOTE The operation of the Soft Panel is described in Chapter 13 ofthe R amp S GTSL Software Description The input fields for the pattern allow for binary and hexadecimal format With hexadecimal entries a lower or uppercase h can be appended to distinguish them from binary format if necessary Spaces are permit ted between characters For stimulus data the letter z Z is also per mitted to identify the Tri State status For reference data the character x X means don t care and the character U means that For bidden Zone is expected as the result 3rd Issue 04 09 ROHDE amp SCHWARZ High Speed Digital Test Module R amp S TS PHDT Input Note Output pattern binary 1000 Binary 00000000 00000000 00000000 00001000 1000h Hexadecimal 00000000 00000000 00010000 00000000 ZZZZ Binary 00000000 00000000 00000000 000
3. No sit e el producto encima de superficies veh culos estantes o mesas que por sus caracter sticas de peso o de estabilidad no sean aptos para l Siga siempre las instrucciones de instalaci n del fabricante cuando instale y asegure el producto en objetos o estructuras p ej paredes y estantes Si se realiza la instalaci n de modo distinto al indicado en la documentaci n del producto pueden causarse lesiones o incluso la muerte No ponga el producto sobre aparatos que generen calor ej radiadores calefactores La temperatura ambiente no debe superar la temperatura m xima especificada en la documentaci n del producto o en la hoja de datos En caso de sobrecalentamiento del producto pueden producirse choques el ctricos incendios y o lesiones graves con posible consecuencia de muerte 1171 0000 42 05 00 Page 8 Informaciones elementales de seguridad Seguridad el ctrica Si no se siguen o se siguen de modo insuficiente las indicaciones del fabricante en cuanto a seguridad el ctrica pueden producirse choques el ctricos incendios y o lesiones graves con posible consecuencia de muerte 1 10 11 Antes de la puesta en marcha del producto se deber comprobar siempre que la tensi n preseleccionada en el producto coincida con la de la red de alimentaci n el ctrica Si es necesario modificar el ajuste de tensi n tambi n se deber n cambiar en caso dado los fusibles correspondientes del producto L
4. 5 1 3 Evaluation functions Evaluation of the recorded pattern must be performed as quickly as possible in the production test The counter and registers have been implemented in the module for this purpose They determine the result in real time The following results are available immediately after the last pattern is executed Number of failed patterns e Failed channels Indices of the failed patterns Data only need to be uploaded from the module to the PC for a detailed evaluation of errors which channel was failed in which pattern or to display all measured values Funktionsbeschreibung ROHDE amp SCHWARZ Funktionsbeschreibung 5 4 High Speed Digital Test Module R amp S TS PHDT 5 1 4 Pattern output and pattern recording Stimulus pattern set for 32 output channels Reference pattern set for 32 input channels Pattern set period different for the two pattern sets e Start via software or hardware trigger Timing of pattern output and pattern recording can be configured inde pendently of each other This makes it possible to record data at a high er rate than the stimulation rate Individual delay times beginning at the trigger event can be adjusted for stimulus and recording Application example Asynchronous serial protocol e Stimulus pattern set sends serial data at lower rate e Recording of the test object response starts after the stimulus pat tern set has been sent e Recording at a higher rate
5. 5 24 High Speed Digital Test Module R amp S TS PHDT 3rd Issue 04 09 3rd Issue 04 09 High Speed Digital Test Module R amp S TS PHDT amp SCHWARZ 6 Commissioning To install plug in module R amp S TS PHDT proceed as follows Shut down and turn off the R amp SCompactTSVP Select a suitable front side connection slot See also in user manual R amp S CompactTSVP TS PCA3 the chapter entitled Permitted module configurations Connection slots 5 to 15 are permitted with the following excep tions The module could not be used in the Backplane version 3 x When using the R amp S TS PSC3 controller only the connection slots 9 to 15 are permitted Loosen the screws and remove the appropriate front plate section on the TSVP housing CAUTION D Check the backplane connectors for bent pins Any pins that are bent must be straightened Failure to observe this instruction may result in permanent dam age to the backplane Press in the module applying moderate pressure The upper catch pin of the R amp S TS PHDT module must be guided into the right hole while the lower catch pin is guided into the left hole of the R amp S CompactTSVP housing CAUTION D When the R amp S TS PHDT module is connected it must be guided with both hands and carefully pressed into the backplane con nector When the R amp S TS PHDT module is correctly inserted you will fee
6. etc all channels Tri State pStim 1023 pTriState 1023 0x00000000 OxFFFFFFFF 3rd Issue 04 09 3rd Issue 04 09 High Speed Digital Test Module R amp S TS PHDT Download data to stimulus memory rsphdt LoadData vi RSPHDT VAL DATA STIM pTriState 1024 amp id Data arrays are no longer required now free pStim free pTriState ROHDE amp SCHWARZ Funktionsbeschreibung pStim The transfer to reference memory is a similar process 5 2 1 Stimulus memory The coding of stimulus memory is as follows Bank 2 Bank 1 Function Tri State Stim 0 0 Drive Low 0 1 Drive High 1 0 reserved 1 1 Drive Tri State Table 5 2 Coding of stimulus memory If only High Low will be stimulated Bank 2 does not need to be trans ferred to the R amp S TS PHDT In this case memory is automatically filled with zeros 5 2 2 Reference memory High Low information similar to stimulus memory Bank 4 Bank 3 Function Control Level 0 0 Expect Low 0 1 Expect High 1 0 don t care 1 1 Expect Forbidden Zone FBZ Table 5 3 Reference memory coding If only High Low is expected Bank 4 does not need to be transferred to the R amp S TS PHDT In this case memory is automatically filled with ze ROHDE amp SCHWARZ Funktionsbeschreibung High Speed Digital Test Module R amp S TS PHDT ros The value don t care
7. from Europe except US public holidays Eastern Standard Time EST 888 test rsa 888 837 8772 opt 2 1 410 910 7800 opt 2 1 410 910 7801 CustomerSupport rohde schwarz com except Singaporean public holidays Singapore Time SGT 65 6 513 0488 65 6 846 1090 CustomerSupport rohde schwarz com except German public holidays Central European Time CET 49 0 180 512 42 42 From outside Europe 49 89 4129 13776 Fax E mail 49 0 89 41 29 637 78 CustomerSupport rohde schwarz com 0 14 Min within the German fixed line telephone network varying prices for the mobile telephone network and in different countries ROHDE amp SCHWARZ 3rd Issue 04 09 amp SCHWARZ High Speed Digital Test Module R amp S TS PHDT Content Content 1 Usage 1 1 1 1 General 1 1 1 2 Features of the module R amp S TS PHDT 1 2 1 3 Safety instructions 1 3 2 View 2 1 Block Diagram 3 1 4 Layout 4 1 4 1 Mechanical layout of the module R amp S TS PHDT 4 1 4 2 Display elements of the module R amp S TS PHDT 4 2 5 Functional Description 5 1 5 1 Overview 5 1 5 1 1 General 5 1 5 1 2 Simple dynamic digital test 5 2 5 1 3 Evaluation functions 5 3 5 1 4 Pattern output and pattern recording 5 4 5 1 5 Overwriting stimulus data 5 4 5 1 6 Stimulus formatting 5 5 5 1 7 Stop on fail 5 5 5 2 Memory layout 5 6 5 2 1 Stimulus memory 5 7 5 2 2 Reference memory 5 7 5 2 3 Results memory 5 8 5 2 3 1 Measurement
8. 7 M66EN AD 8 AD 9 3 34 AD 10 AD 11 V I O GND AD 12 AD 13 GND AD 14 AD 15 3 34 C BE 1 PAR 3 3V GND SERR PERR GND IPMB_SDA IPMB_SCL 3 3V LOCK STOP V I O GND DEVSEL TRDY BD_SEL IRDY FRAME 3 3V Key Area C BE 2 GND AD 16 AD 17 AD 18 AD 19 AD 20 3 3V GND AD 21 AD 22 GND AD 23 IDSEL C BE 3 AD 24 AD 25 V 1 0 GND AD 26 AD 27 GND AD 28 AD 29 AD 30 AD 31 CLK 3 3V GND REQ GNT GND RST BSRSV BSRSV INTS V 1 0 HEALTHY IPMB_PWR INTD 5V INTC INTB INTA TDI TMS 5V TCK o co 2 NN amp OO 5V TRST 12V 5V Table 9 1 Pin assignment for connector X1 9 1 amp SCHWARZ Interface description High Speed Digital Test Module R amp S TS PHDT 9 2 Connector X20 NN P ODN Table 9 2 Pin assignment for connector X20 9 2 3rd Issue 04 09 3rd Issue 04 09 ROHDES SCHWARZ High Speed Digital Test Module R amp S TS PHDT Interface description 9 3 Connector X10 Plug type DIN 41612 96 pin female Figure 9 3 Connector X10 view front panel A B C 1 2 3 4 GND 5 OUT OUT2 OUT3 6 IN1 IN2 IN3 7 OUTA OUT5 OUT6 8 IN4 IN5 ING 9 OUT7 OUT8 10 IN7 IN8 GND 11 OUT9 OUT10 OUT11 12 IN9 IN10 IN11 13 OUT12 OUT13 OUT14 Table 9 3
9. After Trigger Delay the rising edge of signal STIM CLK causes the first pattern to be generated The next rising edge causes the second pattern to be generated etc After the programmed Trigger Delay and Response Delay signal RESP_CLK starts The rising edge marks the point when sampling of the input channels begins In this example the trigger delay for data output and recording are set to the same value ROHDE amp SCHWARZ Funktionsbeschreibung 5 16 High Speed Digital Test Module R amp S TS PHDT 5 8 Mode for data recording Function rsphdt ConfigureCollectionMode defines the format for data in results memory The user can select between saving the pat tern that is read in RSPHDT VAL COLLECT DATA and storing error information RSPHDT VAL COLLECT RESULTS The formats are de scribed in Section 5 2 3 Results memory 5 9 Cancel if error is detected Function rsphdt_ConfigureStopOnFail can be used to config ure sequence controls so that execution of the pattern set ends as soon as an error is detected by the comparison of measurement and refer ence data Stop on Fail If this happens the pattern output as well as recording are interrupted NOTE Depending on the system it may be possible that execution does not end until one or two more patterns after an error is detected 3rd Issue 04 09 3rd Issue 04 09 ROHDE amp SCHWARZ High Speed Digital Test Module R amp
10. Instruments are required to operate the driver Software 7 1 ROHDE amp SCHWARZ Software High Speed Digital Test Module R amp S TS PHDT 7 2 Soft Panel A Soft Panel is available for the module The Soft Panel is based on the IVI driver and allows for interactive operation of the module dh TS PHDT Simulation y 101 xl Eile Configure Utility Help Stimulus Data 3 Reference Data 3 Response Data 9 00000000 00000000 00000000 0000000 00000000 00000000 00000000 0000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000001 00000000 00000000 00000000 00000001 00000000 00000000 00000000 00000001 00000010 00000000 00000000 00000000 00000010 00000000 00000000 00000000 00000010 00000011 00000000 00000000 00000000 00000011 11111100 00000100 00000000 00000000 00000000 00000100 00000000 00000000 00000000 00000100 00000101 00000000 00000000 00000000 00000101 00000000 00000000 00000000 00000101 00000110 00000000 00000000 00000000 00000110 00000000 00000000 00000000 00000110 00000111 00000000 00000000 00000000 00000111 i CN Miia 11111000 00001000 00000000 00000000 00000000 00001000 00000000 00000000 00000000 00001000 Mode Selection Leave Execution Failed Pattern Count
11. Pin assignment for connector X10 view front panel 9 3 ROHDE amp SCHWARZ Interface description High Speed Digital Test Module R amp S TS PHDT A B C 14 IN12 IN13 IN14 19 OUT15 OUT16 16 IN15 IN16 GND 17 OUT17 OUT18 OUT19 18 IN 17 IN18 IN19 19 OUT20 OUT21 OUT22 20 IN20 IN21 IN21 21 OUT23 OUT24 22 IN23 IN24 GND 23 OUT25 OUT26 OUT27 24 IN25 IN26 IN27 25 OUT28 OUT29 OUT30 26 IN28 IN29 IN30 27 OUT31 OUT32 28 IN31 IN32 GND 29 XTO1 XTO2 XTI2 30 XTI1 BURST AUX_CLK 31 SYNCIN STIM_CLK GND 32 SYNCOUT RESP_CLK CHA_GND Table 9 3 Pin assignment for connector X10 view front panel Comment The CHA_GND signal is connected with the front plate of the module and via two 10 nF capacitors with GND The front plate itself has no di rect connection to GND When a test object is connected the test ob ject GND should be connected to GND To avoid ripple loops do not connect GND and CHA_GND 3rd Issue 04 09 3rd Issue 04 09 ROHDE amp SCHWARZ High Speed Digital Test Module R amp S TS PHDT Interface description 9 4 Connector X30 900000 gt Olm e Ojo 000 Op leoo oo o Olm oO a Figure 9 4 Connector X30 view plug side Pin E D C B A GND oO Y 1 ABD2 ABD1 Table 9 4 Pin assignment for connector X
12. S TS PHDT Funktionsbeschreib 5 10 Triggering and sequence control A separate sequence control is available for the stimulus and recording unit Various trigger sources are available to start controllers Name Note Immediate Sequence control starts immediately after arming when function rsphdt_InitiateExecution or rsphdt_InitiateExecutionEx 1 called External See XTI1 ATI XTI2 TTL inputs on the front side connector positive signal edge triggers sequence control PXIO PXI7 Positive signal edges on the PXI trigger lines start sequence control Table 5 6 Trigger sources Function rsphdt ConfigureTriggerSource determines the trig ger source Driver function xsphdt InitiateExecution and rsphdt InitiateExecutionEx enable the previously configured trigger source Then the addressed sequence controls are in Waiting state If trigger source Immediate is selected the corresponding con troller immediately switches to Running state Otherwise the change of the state does not take place until after the trigger event occurs In this state the number of patterns in stimulus memory are generated and the number of patterns in reference memory are recorded If only patterns will be generated the value RSPHDT INVALID DATA ID must be passed to the Initiate function as an ID for reference data If only recording should t
13. The trigger source for stimulus and recording can be configured inde pendently of each other for example stimulus via software trigger and recording via hardware trigger It is also possible to generate only pattern sets or to record only re sponses of the test object 5 1 5 Overwriting stimulus data Stimulus and reference data that has already been loaded into the R amp S TS PHDT module can be subsequently modified Application example Flash programming stimulus pattern set contains an extensive Flash sequence A serial number must be programmed for each test object Only a small part of the sequence needs to be replaced to do this The entire sequence does not need to be transferred again 3rd Issue 04 09 3rd Issue 04 09 ROHDE amp SCHWARZ High Speed Digital Test Module R amp S TS PHDT Funktionsbeschreibung 5 1 6 Stimulus formatting Stimulus signals can be formatted channel specifically return to zero or RTZ A logical High appears only during a time window within a pattern e Figure 5 2 Return to zero formatting 5 1 7 Stop on fail The Stop on fail operating mode is used to cancel running pattern sets prematurely in the event of an error Stop on fail saves testing time if you are only interested in a Pass Fail outcome and not the complete record of test object responses ROHDE amp SCHWARZ Funktionsbeschreibung Vilnt32 id ViUlnt32 pStim ViUInt32 pTri
14. be handled with care In some cases the user may require a suitable means of lifting or moving the product e g with a lift truck to avoid back or other physical injuries 1171 0000 42 05 00 Page 5 Informaciones elementales de seguridad 2 Handles on the products are designed exclusively to enable personnel to transport the product It is therefore not permissible to use handles to fasten the product to or on transport equipment such as cranes fork lifts wagons etc The user is responsible for securely fastening the products to or on the means of transport or lifting Observe the safety regulations of the manufacturer of the means of transport or lifting Noncompliance can result in personal injury or material damage 3 If you use the product in a vehicle it is the sole responsibility of the driver to drive the vehicle safely and properly The manufacturer assumes no responsibility for accidents or collisions Never use the product in a moving vehicle if doing so could distract the driver of the vehicle Adequately secure the product in the vehicle to prevent injuries or other damage in the event of an accident Waste disposal 1 If products or their components are mechanically and or thermally processed in a manner that goes beyond their intended use hazardous substances heavy metal dust such as lead beryllium nickel may be released For this reason the product may only be disassembled by specially trained personnel Improper di
15. called a block is indicated by returning the starting index and block length provided blocks are still in storage When a pattern set 1 started error memory is automatically deleted re gardless of the Initiate function that was used Thus the errors of the last execution are always received 3rd Issue 04 09 3rd Issue 04 09 amp SCHWARZ High Speed Digital Test Module R amp S TS PHDT Funktionsbeschreibung 5 12 Generating trigger signals The High Speed Digital Test Module R amp S TS PHDT is capable of gen erating trigger signals on the following lines Name Note XTO1 XTO2 TTL outputs on the front connector PXIO PXI7 PXI trigger lines on the backplane Table 5 7 Trigger outputs For a change to occur on the trigger lines an event must be assigned to the selected line that generates the trigger pulse The following event is possible Name Note General Purpose Function rsphdt_InitiateTrigger gen Trigger erates a pulse of approximately 200 ns length on the configured trigger lines Table 5 8 Events for generating a trigger pulse The polarity of the trigger signal can also be determined for the individ ual outputs The output driver for the PXI trigger lines can also be switched off All settings are made with the aid of function rsphdt ConfigureTriggerOutput 5 13 Bidirectional channels Each input can be connected individually with the c
16. green on PWR LED At least one power supply voltage is missing green off ERR LED If the green LED is turned on at the same time no red off detectable error is present ERR LED Hardware error is present red on Table 8 2 Observations about the power on test 3rd Issue 04 09 3rd Issue 04 09 ROHDE amp SCHWARZ High Speed Digital Test Module R amp S TS PHDT Self Test 8 3 TSVP self test As part of the TSVP self test an extensive test of the R amp S TS PHDT module is performed and an exhaustive protocol is generated This is done with the Self Test Support Library The R amp S TS PSAM analog stimulus and measurement module is used as a measurement unit in the TSVP self test The functionality of the modules in the system is ensured by measurements via the analog bus NOTE You can find information about starting the self test and the or der of required work steps as well as a detailed description of pa rameters and sequences that are tested in the R amp S Com pactTSVP R amp S Power TSVP Service Manual 8 3 amp SCHWARZ Self Test High Speed Digital Test Module R amp S TS PHDT 3rd Issue 04 09 3rd Issue 04 09 ROHDES SCHWARZ High Speed Digital Test Module R amp S TS PHDT Interface description 9 Interface description 9 1 Connector X1 5V 3 3V ENUM REQ64 5V ACK64 ADIO V O 5V AD 1 AO 5V 3 3 3V ADI 5 AD 6 3 3V GND AD
17. include the complete pattern set or an ex cerpt of it It may be useful uploading Pass Fail data starting with the first failing pattern An excerpt is defined by the parameters Start in dex and Number of patterns amp SCHWARZ Funktionsbeschreibung High Speed Digital Test Module R amp S TS PHDT 5 12 5 4 Configuration of stimulus channels The voltage level and current limiting for the outputs can be adjusted with function rsphdt ConfigureStimPort The settings are al ways made specifically for one port Separate current limiting can be adjusted for high and low level NOTE LP The output resistance of the driver and the resistors in the output safety circuits about 39 results in a drop in voltage when a current is flowing This may have to be taken into consideration when adjusting the level 12 V Driver Fuse Filter Figure 5 3 Output safety circuit 3rd Issue 04 09 3rd Issue 04 09 ROHDES SCHWARZ High Speed Digital Test Module R amp S TS PHDT Funktionsbeschreibung 5 5 Configuration of the measurement channels The measurement channel inputs have a safety circuit before the com parators that is structured as follows 12 Y Comparators INx Figure 5 4 Input safety circuit Each input is directed to two comparators with adjustable thresholds This makes it possible to implement a hysteresis for evaluating signals The thresholds can be set using driver functio
18. las personas No utilice el producto en condiciones en las que pueda producirse o ya se hayan producido condensaciones sobre el producto o en el interior de ste como p ej al desplazarlo de un lugar fr o a otro caliente La entrada de agua aumenta el riesgo de choque el ctrico Antes de la limpieza desconecte por completo el producto de la alimentaci n de tensi n p ej red de alimentaci n o bater a Realice la limpieza de los aparatos con un pa o suave que no se deshilache No utilice bajo ning n concepto productos de limpieza qu micos como alcohol acetona o diluyentes para lacas nitrocelul sicas Funcionamiento 1 2 3 4 El uso del producto requiere instrucciones especiales y una alta concentraci n durante el manejo Debe asegurarse que las personas que manejen el producto est n a la altura de los requerimientos necesarios en cuanto a aptitudes f sicas ps quicas y emocionales ya que de otra manera no se pueden excluir lesiones o da os de objetos El empresario u operador es responsable de seleccionar el personal usuario apto para el manejo del producto Antes de desplazar o transportar el producto lea y tenga en cuenta el cap tulo Transporte Como con todo producto de fabricaci n industrial no puede quedar excluida en general la posibilidad de que se produzcan alergias provocadas por algunos materiales empleados los llamados al rgenos ej el n quel Si durante el manejo de productos Rohde am
19. network the plug of the connecting cable is regarded as the disconnecting device In such cases always ensure that the power plug is easily reachable and accessible at all times corresponding to the length of connecting cable approx 2 m Functional or electronic switches are not suitable for providing disconnection from the AC supply network If products without power switches are integrated into racks or systems a disconnecting device must be provided at the system level 5 Never use the product if the power cable is damaged Check the power cable on a regular basis to ensure that it is in proper operating condition By taking appropriate safety measures and carefully laying the power cable you can ensure that the cable will not be damaged and that no one can be hurt by for example tripping over the cable or suffering an electric shock 6 The product may be operated only from TN TT supply networks fused with max 16 A higher fuse only after consulting with the Rohde amp Schwarz group of companies 7 not insert the plug into sockets that are dusty or dirty Insert the plug firmly and all the way into the socket Otherwise sparks that result in fire and or injuries may occur 8 Do not overload any sockets extension cords or connector strips doing so can cause fire or electric shocks 9 For measurements in circuits with voltages V ms gt 30 V suitable measures e g appropriate measuring equipment fusing current limitin
20. reciclarse y no deben tirarse a la basura dom stica Las bater as o acumuladores que contienen plomo mercurio o cadmio deben tratarse como residuos especiales Respete en esta relaci n las normas nacionales de eliminaci n y reciclaje Transporte 1 El producto puede tener un peso elevado Por eso es necesario desplazarlo o transportarlo con precauci n y si es necesario usando un sistema de elevaci n adecuado p ej una carretilla elevadora a fin de evitar lesiones en la espalda u otros da os personales Las asas instaladas en los productos sirven solamente de ayuda para el transporte del producto por personas Por eso no est permitido utilizar las asas para la sujeci n en o sobre medios de transporte como p ej gr as carretillas elevadoras de horquilla carros etc Es responsabilidad suya fijar los productos de manera segura a los medios de transporte o elevaci n Para evitar da os personales o da os en el producto siga las instrucciones de seguridad del fabricante del medio de transporte o elevaci n utilizado Si se utiliza el producto dentro de un veh culo recae de manera exclusiva en el conductor la responsabilidad de conducir el veh culo de manera segura y adecuada El fabricante no asumir ninguna responsabilidad por accidentes o colisiones No utilice nunca el producto dentro de un veh culo en movimiento si esto pudiera distraer al conductor Asegure el producto dentro del veh culo debidamente para evitar en ca
21. values 5 8 5 2 3 2 Error information 5 9 5 3 Upload Download data 5 10 5 4 Configuration of stimulus channels 5 12 5 5 Configuration of the measurement channels 5 13 5 6 Time settings for data output 5 14 5 7 Time settings for data recording 5 15 5 8 Mode for data recording 5 16 5 9 Cancel if error is detected 5 16 ROHDE amp SCHWARZ Content High Speed Digital Test Module R amp S TS PHDT 5 10 Triggering and sequence control 5 11 Result evaluation 5 11 1 Number of patterns executed current pattern index 5 11 2 Number of failed patterns 5 11 3 Failed channels 5 11 4 Number of failed channels 5 11 5 Failed patterns 5 12 Generating trigger signals 5 13 Bidirectional channels 5 14 Generating a static pattern 5 15 Querying the inputs 5 16 Configuration of clock signals 5 17 Synchronising multiple modules 6 Commissioning 7 Software 7 1 Driver software 7 2 Soft Panel 7 3 Sample program R amp S TS PHDT 8 Self Test 8 1 LED test 8 2 Power on test 8 3 TSVP self test 9 Interface description 9 1 Connector X1 9 2 Connector X20 9 3 Connector X10 9 4 Connector X30 10 Specifications 5 17 5 19 5 19 5 19 5 19 5 20 5 20 5 21 5 21 5 22 5 22 5 23 5 23 6 1 7 1 7 1 7 2 7 4 8 1 8 1 8 2 8 3 9 1 9 1 9 2 9 3 9 5 10 1 3rd Issue 04 09 ROHDE amp SCHWARZ 3rd Issue 04 09 High Speed Digital Test Module R amp S TS PHDT Figures Figures Figure 2 1 View of the High Speed Digital Test Modul
22. 0ZZZZ zzzzh Hexadecimal 00000000 00000000 77727727272 27777777 55555555 Hexadecimal 01010101 01010101 01010101 01010101 FFFFFFFF Hexadecimal 11111111 11111111 11111111 11111111 1111 1111 Binary 00000000 00000000 00000000 11111111 Software 3rd Issue 04 09 Table 7 2 Input formats for pattern A U with result data means that the measured level was within the for bidden zone 7 3 amp SCHWARZ Software High Speed Digital Test Module R amp S TS PHDT 7 3 Sample program R amp S TS PHDT This sample shows a simple digital functional test Sample pattern Stimulus channel OUT1 generates a clock signal Stimulus channel OUT2 generates a enable signal Response chann INT expects the inverted clock signal Response chann IN2 expects the direct clock signal if enable high Pattern 0 1 2 3 4 5 6 7 Stimulus outl out2 Response inl 102 XXXXXXXXXXXXXXXXXX Error handling is not considered in this sample in order to keep it easy to read The return status should be checked for VI SUCCESS after each driver call include rsphdt h define PATTERN COUNT 8 Pattern 0 1 2 3 4 5 6 7 static ViUInt32 s StimLvl PATTERN COUNT 0 1 0 3 2 3 2 3 static ViUInt32 s RefLvl PATTERN COUNT 1 0 1 2 1 2 1 2
23. 30 9 5 ROHDE amp SCHWARZ Interface description 9 6 High Speed Digital Test Module R amp S TS PHDT 3rd Issue 04 09 3rd Issue 04 09 ROHDE amp SCHWARZ High Speed Digital Test Module R amp S TS PHDT Specifications 10 Specifications NOTE le Technical data for the High Speed Digital Test Module R amp S TS PHDT is specified in the corresponding data sheets If there are discrepancies between the information in this op erating manual and the values of the data sheet the values of the data sheet take precedence 10 1 ROHDE amp SCHWARZ Specifications 10 2 High Speed Digital Test Module R amp S TS PHDT 3rd Issue 04 09
24. 91 122 Fax 49 30 655 50 221 info ftk rohde schwarz com Phone 49 30 658 84 0 Fax 49 30 658 84 183 info sit rohde schwarz com Phone 49 22 03 49 5 23 25 Fax 49 22 03 49 5 23 36 info rssys rohde schwarz com Phone 49 431 600 51 0 Fax 49 431 600 51 11 sales gedis online de Phone 49 61 82 800 0 Fax 49 61 82 800 100 info hameg de Locations Worldwide Please refer to our homepage www rohde schwarz com Sales Locations Service Locations National Websites Customer Support Technical support where and when you need it For quick expert help with any Rohde amp Schwarz equipment contact one of our Customer Support Centers A team of highly qualified engineers provides telephone support and will work with you to find a solution to your query on any aspect of the operation programming or applications of Rohde amp Schwarz equipment Up to date information and upgrades To keep your instrument up to date and to be informed about new application notes related to your instrument please send an e mail to the Customer Support Center stating your instrument and your wish We will take care that you will get the right information USA amp Canada East Asia Rest of the World 1171 0200 22 03 00 Monday to Friday 8 00 AM 8 00 PM Tel from USA From outside USA Fax E mail Monday to Friday 8 30 AM 6 00 PM Tel Fax E mail Monday to Friday 08 00 17 00 Tel
25. Informaciones elementales de seguridad Si un producto se instala en un lugar fijo se deber primero conectar el conductor de protecci n fijo con el conductor de protecci n del producto antes de hacer cualquier otra conexi n La instalaci n y la conexi n deber n ser efectuadas por un electricista especializado En el caso de dispositivos fijos que no est n provistos de fusibles interruptor autom tico ni otros mecanismos de seguridad similares el circuito de alimentaci n debe estar protegido de modo que todas las personas que puedan acceder al producto as como el producto mismo est n a salvo de posibles da os Todo producto debe estar protegido contra sobretensi n debida p ej a una ca da del rayo mediante los correspondientes sistemas de protecci n Si no el personal que lo utilice quedar expuesto al peligro de choque el ctrico No debe introducirse en los orificios de la caja del aparato ning n objeto que no est destinado a ello Esto puede producir cortocircuitos en el producto y o puede causar choques el ctricos fuego o lesiones Salvo indicaci n contraria los productos no est n impermeabilizados ver tambi n el cap tulo Estados operativos y posiciones de funcionamiento punto 1 Por eso es necesario tomar las medidas necesarias para evitar la entrada de l quidos En caso contrario existe peligro de choque el ctrico para el usuario o de da os en el producto que tambi n pueden redundar en peligro para
26. ROHDE amp SCHWARZ USER MANUAL High Speed Digital Test Module R amp S TS PHDT User Manual for ROHDE amp SCHWARZ High Speed Digital Test Module R amp S TS PHDT 3rd Issue 04 09 GB 1157 9710 12 All rights also translation into foreign languages are reserved No part of this manual is permitted to be reproduced in any form print photocopy or any other method also not for the preparation of lectures or processed reproduced or made available using electronic systems without written permission from ROHDE amp SCHWARZ The passing on to third parties and the reproduction of this documentation utilisation and com munication of its contents is not permitted unless specifically approved Infringements will incur claims for damages All rights reserved in the case of the award of a patent or registration of a design R amp S is a registered trademark of ROHDE amp SCHWARZ GmbH amp Co KG We draw to your attention that the names of software and hardware used in the Service Manual and the brand names of the respective companies are in general the subject of protection as trademarks or under proprietary rights or patent law ROHDE amp SCHWARZ GmbH amp Co KG Corporate Headquarters Telephone 49 0 89 4129 13774 M hldorfstr 15 Fax 49 0 89 4129 13777 D 81671 M nchen Printed in the Federal Republic of Germany Errors excepted subject to technical change without notice Basic Safety In
27. State High Speed Digital Test Module R amp S TS PHDT 5 2 Memory layout The R amp S TS PHDT module provides memory for 64 M patterns Mem ory is divided into 6 memory banks each with 64 M x 32 bits Each of the 32 bits is assigned to one of the 32 input or output channels The meaning of the individual bits is as follows e Stimulus memory banks 1 and 2 Activation of the output channels High Low Tri State Reference memory banks and 4 Coding of the expected measurement value High Low Forbid den Zone don t care Results memory banks 5 and 6 Coding of the measured value High Low Forbidden Zone or er ror information Pass Fail Memory layout is designed so that all data is already available on the PC in such a manner that it can be transferred directly to memory with out calculating or recopying Transfer of data therefore always takes place in two equally long 32 bit data arrays in which the contents of the memory banks are transferred The user must prepare the arrays fill them with data and then transfer them to the module internal memory of the R amp S TS PHDT calloc 1024 sizeof ViUInt32 calloc 1024 sizeof ViUInt32 all channels LOW pStim 0 0x00000000 pTriState 0 0x00000000 OUT1 HIGH pStim 1 0x00000001 pTriState 1 0x00000000 all channels HIGH pStim 2 OxFFFFFFFF pTriState 2 0x00000000
28. TS PHDT module means either stimulus data or reference and results data Stimulus data Banks 1 and 2 may there fore have a different length than reference data Banks 3 and 4 Stim ulus and reference data are loaded into R amp S TS PHDT memory before execution Results data Banks 5 and 6 match reference data in terms of their length and position in memory They are not available until after the pattern set has been executed Then they can be loaded onto the PC for evaluation It is also possible for special applications to execute only one stimulus pattern set or to record only responses of the test object In the latter cases reference data must also be physically present in R amp S TS PHDT memory They do not need to be explicitly provided however if no comparison is required In this case don t care is automatically as signed to them When downloading a pattern set the data type stimulus or reference data number of patterns and the pointers to the two data arrays cor responding to the format of the two memory banks involved are trans ferred The device driver transfers the data to the module and returns an ID i e a unique identification number The data record can be ref erenced later with this ID Stimulus and reference data are transferred using function rsphdt_LoadData to the R amp S TS PHDT module download The data must be provided in two 32 bit arrays The data format corre sponds exactl
29. ake place the val ue above must be passed as an ID for the stimulus data After the set number of patterns have been processed the correspond ing sequence control reverts to the Stopped state The Stopped state is also reached is an error is detected when com paring reference and measurement data with the Stop on Fail option turned on When this happens both sequence controls stop The current state of both sequence controls can be queried with func tion rsphdt FetchExecutionState Function rsphdt WaitUntilExecutionComplete waits in the test pro gram for the end of execution ung ROHDE amp SCHWARZ Funktionsbeschreibung 5 18 High Speed Digital Test Module R amp S TS PHDT The BURST signal on the front connector is active if at least one of the two process controls is in the Running state NOTE If sequence control is in the Waiting or Running state some functions cannot be performed In that case those functions re turn an error message If necessary sequence control can be switched to its reset state with the rsphdt_AbortExecution function 3rd Issue 04 09 3rd Issue 04 09 amp SCHWARZ High Speed Digital Test Module R amp S TS PHDT Funktionsbeschreibung 5 11 Result evaluation After a pattern set is executed some status information must be avail able immediately i e without transferring and analysing large quanti t
30. all assume no responsibility for such use of the product The product is used for its designated purpose if it is used in accordance with its product documentation and within its performance limits see data sheet documentation the following safety instructions Using the product requires technical skills and a basic knowledge of English It is therefore essential that only skilled and specialized staff or thoroughly trained personnel with the required skills be allowed to use the product If personal safety gear is required for using Rohde amp Schwarz products this will be indicated at the appropriate place in the product documentation Keep the basic safety instructions and the product documentation in a safe place and pass them on to the subsequent users Observing the safety instructions will help prevent personal injury or damage of any kind caused by dangerous situations Therefore carefully read through and adhere to the following safety instructions before and when using the product It is also absolutely essential to observe the additional safety instructions on personal safety for example that appear in relevant parts of the product documentation In these safety instructions the word product refers to all merchandise sold and distributed by the Rohde amp Schwarz group of companies including instruments systems and all accessories Symbols and safety labels E A A A k Notic
31. amp readRespPatternCnt 3rd Issue 04 09 3rd Issue 04 09 ROHDE amp SCHWARZ High Speed Digital Test Module R amp S TS PHDT Software reset module close the driver session status rsphdt_close vi return 0 7 7 ROHDE amp SCHWARZ Software 7 8 High Speed Digital Test Module R amp S TS PHDT 3rd Issue 04 09 3rd Issue 04 09 ROHDE amp SCHWARZ High Speed Digital Test Module R amp S TS PHDT Self Test 8 Self Test The High Speed Digital Test Module R amp S TS PHDT has an integrated capability for self test The following tests are possible e LED test e Power on test e TSVP self test 8 1 LED test After the system is turned on all LEDs are lit for about one second This indicates that the required power supply has been applied and all LEDs are in proper order The following observations may be made about dif ferent display states LED One individual LED is not lit Description Hardware problem in the module LED faulty No LEDs are lit 5 V power supply voltage missing Table 8 1 Observations about the LED test 8 1 amp SCHWARZ Self Test High Speed Digital Test Module R amp S TS PHDT 8 2 Power on test The power on test runs in parallel to the LED test The following obser vations may be made about the different display states of the LEDs LED Description PWR LED All power supply voltages are present
32. arameter deter mines the length of the RTZ signal It must be remembered that the to tal of the delay and length must be less than or equal to the pattern set period These settings have an effect on the clock signal AUX_CLK on the front connector see also Figure 5 2 Return to zero formatting RTZ mode can be activated for each channel individually using the function rsphdt EnableReturnToZeroMode Issue 04 09 3rd Issue 04 09 amp SCHWARZ High Speed Digital Test Module R amp S TS PHDT Funktionsbeschreibung xTM STIM CLK RESP CLK Figure 5 5 Time settings 5 7 Time settings for data recording Three time parameters can be set with function rsphdt ConfigureRespTiming to record input signals As was the case for pattern output trigger delay and pattern set period are available as parameters In addition the delay between the beginning ofthe pattern and the sampling point can also be configured Response Delay This setting also affects the clock signal RESP CLK on the front connector Figure 5 5 shows an example of the effects of time settings on clock signals and thus on data output and recording In this figure the polarity of the clock signals is set to active high See also Section 5 16 Configuration of clock signals Trigger l Response Delay Delay I Pattern Period u nl The rising edge of the signal on trigger input XTI starts starts execution
33. chen Plants ROHDE amp SCHWARZ Messger tebau GmbH Riedbachstra e 58 D 87700 Memmingen P 0 Box 16 52 D 87686 Memmingen ROHDE amp SCHWARZ GmbH amp Co KG Werk Teisnach Kaikenrieder Stra e 27 D 94244 Teisnach P 0 Box 11 49 D 94240 Teisnach ROHDE amp SCHWARZ z vod Vimperk s r o Location Spidrova 49 CZ 38501 Vimperk ROHDE amp SCHWARZ GmbH amp Co KG Dienstleistungszentrum K ln Graf Zeppelin Stra e 18 D 51147 K ln P 0 Box 98 02 60 D 51130 K ln Subsidiaries R amp S BICK Mobilfunk GmbH Fritz Hahne Str 7 D 31848 Bad M nder P 0 Box 20 02 D 31844 Bad M nder ROHDE amp SCHWARZ FTK GmbH Wendenschlo stra e 168 Haus 28 D 12557 Berlin ROHDE amp SCHWARZ SIT GmbH Am Studio 3 D 12489 Berlin R amp S Systems GmbH Graf Zeppelin Stra e 18 D 51147 K ln GEDIS GmbH Sophienblatt 100 D 24114 Kiel HAMEG Instruments GmbH IndustriestraRe 6 D 63533 Mainhausen 1171 0200 42 02 00 Phone 49 89 41 29 0 Fax 49 89 41 29 121 64 info rs rohde schwarz com Phone 49 83 31 1 08 0 49 83 31 1 08 1124 info rsmb rohde schwarz com Phone 49 99 23 8 50 0 Fax 49 99 23 8 50 174 info rsdts rohde schwarz com Phone 420 388 45 21 09 Fax 420 388 45 21 13 Phone 49 22 03 49 0 Fax 49 22 03 49 51 229 info rsdc rohde schwarz com service rsdc rohde schwarz com Phone 49 50 42 9 98 0 Fax 49 50 42 9 98 105 info bick rohde schwarz com Phone 49 30 658
34. e general Caution Danger of Warning PE terminal Ground Ground Be careful when danger location when electric Hot surface terminal handling handling shock electrostatic Observe product heavy sensitive documentation equipment devices ON OFF supply voltage Standby indication Direct current DC AC Alternating current Direct alternating current DC AC Device fully protected by double reinforced insulation 1171 0000 42 05 00 Page 1 Basic Safety Instructions Tags and their meaning The following signal words are used in the product documentation in order to warn the reader about risks and dangers indicates a hazardous situation which if not avoided will result in death or 4 DANGER serious injury indicates a hazardous situation which if not avoided could result in death or indicates a hazardous situation which if not avoided could result in minor or moderate injury indicates the possibility of incorrect operation which can result in damage to NOTICE the product In the product documentation the word ATTENTION is used synonymously These tags are in accordance with the standard definition for civil applications in the European Economic Area Definitions that deviate from the standard definition may also exist in other economic areas or military applications It is therefore essential to make sure that the tags described here are always used only in connection with the relat
35. e R amp S TS PHDT without COVEN t M 2 1 Figure 3 1 Block diagram R amp S 5 3 1 Figure 4 1 Arrangement of the connectors and LEDs on the module A 4 1 Figure 5 1 Pattern set period and response delay 5 3 Figure 5 2 Return to zero formatting ns 5 5 Figure 5 3 Output safety CIU aniston dis 5 12 Figure 5 4 Input safety CIN CU inician 5 13 Figure 5 5 Dixi see 5 15 Figure 7 1 Soft Panel R amp S TS PHDT 4 4 4 z 000 00024 2222240440000 00a Hasena 7 2 Figure 9 1 Connector X1 view plug Side eese 9 1 Figure 9 2 Connector X20 view plug side 9 2 Figure 9 3 Connector X10 view front panel 9 3 Figure 9 4 Connector X30 view plug side 9 5 ROHDE amp SCHWARZ Figures High Speed Digital Test Module R amp S TS PHDT 3rd Issue 04 09 ROHDE amp SCHWARZ 3rd Issue 04 09 High Speed Digital Test Module R amp S TS PHDT Tables Tables Table 1 1 Features R amp S TS PHDT aus 1 2 Table 4 1 Connectors on the R amp S TS PHDT eee 4 1 Table 4 2 Display elements on the module R amp S TS PHDT 4 2 Table 5 1 Assignment of channels to the ports 5 1 Table 5 2 Coding of stimulu
36. e R amp S TS PHDT is used wherever digital circuits are tested by static or dynamic stimulation and the re sponse is recorded Deterministic simultaneous stimulation and recording of digital signals make it possible to simulate operating conditions in a manner ap proaching reality A large local memory pool and an independent se quence controller are available on the module to make it possible gen erating recording and analysing pattern in real time Extensive trigger options via the PXI trigger bus allow for synchronisa tion with additional R amp S TS PHDT modules or other measurement and stimulus modules This makes it possible to extend the number of dig ital channels in an application Measurements in which analog and dig ital signals are recorded synchronously are also possible Output levels and input thresholds can be programmed in groups of 8 channels ports This allows for optimum adaptability to the require ments of different logic families The effect of interference signals in the test setup can be minimised by adjusting the hysteresis for the input thresholds Safety circuits to protect against short circuits countervoltages and ov ervoltages contribute to the robustness of the High Speed Digital Test Module R amp S TS PHDT Due to the extraordinary space saving design of the I O safety circuit and signal conditioning unit the R amp S TS PHDT takes up only one CompactPCI PXI slot This makes it possible to set up v
37. e two pattern sets is identical i e output and recording run synchronously to each other The test object response is recorded with a time delay in reference to the stimulus data The delay can be adjusted between 0 and the pattern set period e Start via software or hardware trigger The R amp S TS PHDT module contains sufficient memory to hold several pattern sets at the same time This means there is no need to reload data on the module for each test Patterns 1 to n can be generated at a fixed rate The pattern set period is the time during which a pattern is available at the outputs Responses of the test object are also recorded at the inputs during this time The Response Delay is the time offset between the beginning of a pattern and recording 3rd Issue 04 09 3rd Issue 04 09 High Speed Digital Test Module R amp S TS PHDT ROHDE amp SCHWARZ The pattern rate is the reciprocal of the pattern set period Figure 5 1 Pattern set period and response delay The pattern set can be started by a software function or by a hardware trigger The software can perform additional tasks during execution i e the pattern set is executed under hardware control The software is able to query whether execution is still in progress has been interrupt ed or may wait for pattern set completion After execution is complete the results are available for additional eval uation error information or recorded patterns
38. ed product documentation and the related product The use of tags in connection with unrelated products or documentation can result in misinterpretation and in personal injury or material damage Operating states and operating positions The product may be operated only under the operating conditions and in the positions specified by the manufacturer without the product s ventilation being obstructed If the manufacturer s specifications are not observed this can result in electric shock fire and or serious personal injury or death Applicable local or national safety regulations and rules for the prevention of accidents must be observed in all work performed 1 Unless otherwise specified the following requirements apply to Rohde amp Schwarz products predefined operating position is always with the housing floor facing down IP protection 2X pollution severity 2 overvoltage category 2 use only indoors max operating altitude 2000 m above sea level max transport altitude 4500 m above sea level A tolerance of 10 shall apply to the nominal voltage and 5 to the nominal frequency Do not place the product on surfaces vehicles cabinets or tables that for reasons of weight or stability are unsuitable for this purpose Always follow the manufacturer s installation instructions when installing the product and fastening it to objects or structures e g walls and shelves An installation that is not carried out as described in the
39. ery high per formance compact measuring systems The High Speed Digital Test Module R amp S TS PHDT is designed for the R amp S CompactTSVP test platform The module is controlled by the CompactPCI bus A Soft Panel is available to operate the module An IVI C driver is avail able to use the module under software control The PLX PCI SDK is used to implement PCI bus access Copyright 2005 PLX Technology Inc Usage ROHDE amp SCHWARZ Usage 1 2 High Speed Digital Test Module R amp S TS PHDT 1 2 Features of the module R amp S TS PHDT 32 output channels high and low level for each port 8 channels separately adjustable Output level range 3 V to 10 V Maximum output current per channel 80 mA Maximum output current per port 500 mA for output level lt 2 9 V 200 mA for output level gt 2 9 V Current limiting for high and low level separately adjustable for each port Each channel is individually switchable to Tri State at the maximum pattern rate High level is formattable within the pattern duration return to zero 32 input channels high and low limit for each port separately adjust able Input can be connected with outputs by channel Maximum pattern rate 40 MHz Independent memories for Stimulus data Reference data Result data Memory depth 64 M patterns each Memory for independent pattern sets selectively executable Comparison o
40. f reference and measurement data in real time results available immediately Pass Fail number of failed patterns chan nels Trigger options via PXI trigger bus Self test capability Soft Panel for interactive operation IVI C driver available Use in R S CompactTSVP Table 1 1 Features amp TS PHDT 3rd Issue 04 09 3rd Issue 04 09 High Speed Digital Test Module R amp S TS PHDT ROHDE amp SCHWARZ 1 3 Safety instructions A WARNING The R amp S CompactTSVP test platform is normally designed for operating voltages up to 125 V The High Speed Digital Test Module R amp S TS PHDT is suitable for voltages from 3 V to 10 V and must only be used accordingly Access to areas that permit higher voltages R amp S analog bus is only possible for internal purposes during the self test Usage 1 3 amp SCHWARZ High Speed Digital Test Module R amp S 3rd Issue 04 09 3rd Issue 04 09 ROHDES SCHWARZ High Speed Digital Test Module R amp S TS PHDT View 2 View Figure 2 1 shows the High Speed Digital Test Module R amp S TS PHDT Figure 2 1 View of the High Speed Digital Test Module R amp S TS PHDT without cover 2 1 ROHDE amp SCHWARZ View High Speed Digital Test Module R amp S TS PHDT 3rd Issue 04 09 3rd Issue 04 09 ROHDE amp SCHWARZ High Speed Digital Test Module R amp S TS PHDT B
41. g LED Description ERR red Fault condition Lights up when a fault is detected on the R amp S TS PHDT module during the power on test after the supply voltage is switched on This means that there is a hardware problem on the module also see section 8 Self test COM yellow Communication Lights up when data is exchanged across the inter face PWR green Supply voltage OK Lights up when all necessary supply voltages are present Table 4 2 Display elements on the module R amp S TS PHDT 3rd Issue 04 09 3rd Issue 04 09 High Speed Digital Test Module R amp S TS PHDT amp SCHWARZ 5 Functional Description 5 1 Overview 5 1 1 General The High Speed Digital Test Module R amp S TS PHDT makes 32 outputs OUT1 to OUT32 and 32 inputs IN1 to IN32 available 8 channels are combined together to form ports PORTO to PORT3 The output level for voltage and current limiting and the thresholds for inputs are individ ually configurable for the individual ports Port PORTx Channels OUTx INx 0 1 8 1 9 16 2 17 24 3 25 32 Table 5 1 Assignment of channels to the ports The timing of the pattern output stimulus part and the timing for sam pling the inputs with the recording unit response part can be separate ly adjusted Triggering is separately configurable for both sequence controls Lines PXIO to PXI7 on the PXI backplane and contact
42. g electrical separation insulation should be taken to avoid any hazards 10 Ensure that the connections with information technology equipment e g PCs or other industrial computers comply with the IEC60950 1 EN60950 1 or IEC61010 1 EN 61010 1 standards that apply in each case 11 Unless expressly permitted never remove the cover or any part of the housing while the product is in operation Doing so will expose circuits and components and can lead to injuries fire or damage to the product 12 If a product is to be permanently installed the connection between the PE terminal on site and the product s PE conductor must be made first before any other connection is made The product may be installed and connected only by a licensed electrician 13 For permanently installed equipment without built in fuses circuit breakers or similar protective devices the supply circuit must be fused in such a way that anyone who has access to the product as well as the product itself is adequately protected from injury or damage 1171 0000 42 05 00 Page 3 14 15 16 17 18 Basic Safety Instructions Use suitable overvoltage protection to ensure that no overvoltage such as that caused by a bolt of lightning can reach the product Otherwise the person operating the product will be exposed to the danger of an electric shock Any object that is not designed to be placed in the openings of the housing must not be used for this purp
43. gh has been measured For don t care Low or High has been measured 0 1 An unexpected value Low or High has been measured 1 0 Forbidden Zone was expected and measured For don t care Forbidden Zone was measured 1 1 Forbidden Zone was measured but not expected Table 5 5 Coding of results memory for Pass Fail and FBZ information The advantage of the Pass Fail storage is that searching for failed pat terns is simple and fast Only the Fail bits need to be considered which means that Bank 6 does not need to be uploaded and evaluated The disadvantage of the Pass Fail save is that the currently measured value can only be reconstructed by a logical link with reference memo ry If reference memory contains don t the current value High or Low cannot be reconstructed at all since don t care always results in the Fail bit being set to zero The FBZ bit can still be used to deter mine whether Forbidden Zone or a valid level was measured but not whether the level was High or Low ROHDE amp SCHWARZ Funktionsbeschreibung 5 10 High Speed Digital Test Module R amp S TS PHDT 5 3 Upload Download data The R amp S TS PHDT module is capable of holding multiple pattern sets in memory simultaneously Because of this feature various digital tests can be performed one after the other without having to reload data to the module each time A pattern set for the R amp S
44. ies of data This information is collected in real time during execution and is available in the R amp S TS PHDT module Since stimulation and recording can take place independently of each other some of these status information items may be available sepa rately 5 11 1 Number of patterns executed current pattern index Function rsphdt_FetchExecutedPatternCount returns the number of patterns that were generated and recorded This information is important if a pattern set has been interrupted for example because of a user request or due to Stop on Fail The function can also be called during execution in which case it re turns the index of the pattern currently present 5 11 2 Number of failed patterns After a pattern set is executed function rsphdt FetchFailedPatternCount returns the number of pat terns in which at least one channel returned a Fail result The function can also be called during execution If execution was started with function rsphdt InitiateExecutionEx the parameter Reset Flag de termines whether the counter will be reset for start Function rsphdt InitiateExecution always sets the number of failed patterns to zero before execution starts 5 11 3 Failed channels Function rsphdt_FetchFailedChannels returns a 32 bit word where the according channel bit is set to 1 if at least one pattern of this channel failed The number
45. l it reach a definite mechanical limit Tighten the upper and lower screws on the front plate of the R amp S TS PHDT module Commissioning ROHDE amp SCHWARZ Commissioning High Speed Digital Test Module R amp S TS PHDT NOTE The High Speed Digital Test Module R amp S TS PHDT is detected automatically by the R amp S CompactTSVP 3rd Issue 04 09 3rd Issue 04 09 High Speed Digital Test Module R amp S TS PHDT ROHDE amp SCHWARZ 7 Software 7 1 Driver software An IVI C driver is available for the functions of the High Speed Digital Test Module R amp S TS PHDT The driver is a component of the ROHDE amp SCHWARZ GTSL software program All functions of the driver are documented extensively in online Help and in the LabWindows CVI Function Panels The following software modules are installed during driver installation Module Path Note rsphat dll lt GTSL directory gt Bin Driver rsphdt hlp lt GTSL directory gt Bin Help file rsphdt fp lt GTSL directory gt Bin LabWindows CVI Function Panel File Function Panels for CVI Development En vironment rsphdt sub lt GTSL directory gt Bin LabWindows CVI attribute file This file is required by several Function Panels rsphdt lib lt GTSL directory gt Bin Import library rsphdt h lt GTSL directory gt Include Header file for driver Table 7 1 Driver installation R amp S TS PHDT er NOTE The IVI and VISA library of National
46. lock Diagram 3 Block Diagram Figure 3 1 shows the block diagram of the R amp S TS PHDT module PCI Interface Response RAM Figure 3 1 Block diagram R amp S TS PHDT 3 1 ROHDE amp SCHWARZ Block Diagram High Speed Digital Test Module R amp S TS PHDT 3rd Issue 04 09 3rd Issue 04 09 amp SCHWARZ High Speed Digital Test Module R amp S TS PHDT Layout 4 Layout 4 1 Mechanical layout of the module R amp S TS PHDT The High Speed Digital Test Module R amp S TS PHDT is designed as a long plug in card for front installation in test platforms R amp S Com pactTSVP The front side connector X10 is used to connect test objects The con nector X30 connects the module with the analog bus backplane in the R amp SCompactTSVP The connectors X20 X1 connect the module with the CompactPCI backplane PXI control backplane Figure 4 1 Arrangement of the connectors and LEDs on the module R amp S TS PHDT Name Use X1 cPCI bus X10 Interface to the test object X20 Extension PXI rear I O X30 Analog Bus ConnectorTSVP analog bus access for self test Table 4 1 Connectors on the R amp S TS PHDT 4 1 ROHDE amp SCHWARZ Layout High Speed Digital Test Module R amp S TS PHDT 4 2 Display elements of the module R amp S TS PHDT On the front side of the module R amp S TS PHDT there are three LEDs which show the current status of the module The LEDs have the fol lowing meanin
47. means that any level including the Forbidden Zone may be measured without an error being reported 5 2 3 Results memory Results memory is filled with data while a pattern set is being executed The recording mode decides which of the two possible data formats should be used Measurement values RSPHDT_VAL_COLLECT_DATA e Datais stored according to the format for stimulus reference mem ory Error information RSPHDT_VAL_COLLECT_RESULTS e Pass Fail information and FBZ are saved e Optimised coding which mixes Pass Fail and current values The two formats each have strengths and weaknesses that are de scribed in the following sections 5 2 3 1 Measurement values Bank 6 Bank 5 Function FBZ Level 0 0 Low measured 0 1 High measured 1 0 reserved 1 1 Forbidden Zone measured Table 5 4 Coding of measurement values in results memory This memory format is ideally suited for recording unknown data from a test object and using it either directly as stimulus data simulation of the test object or as reference data learning procedure The disadvantage is that information about failed patterns can only be obtained through a comparison with reference memory 3rd Issue 04 09 3rd Issue 04 09 ROHDES SCHWARZ High Speed Digital Test Module R amp S TS PHDT Funktionsbeschreibung 5 2 3 2 Error information Bank 6 Bank 5 Function FBZ Fail 0 0 The expected value Low or Hi
48. mentaria de seguridad para el uso de productos de Rohde amp Schwarz encontrar a la informaci n debida en la documentaci n del producto en el cap tulo correspondiente Guarde bien las informaciones de seguridad elementales as como la documentaci n del producto y entr guelas a usuarios posteriores Tener en cuenta las informaciones de seguridad sirve para evitar en lo posible lesiones o da os por peligros de toda clase Por eso es imprescindible leer detalladamente y comprender por completo las siguientes informaciones de seguridad antes de usar el producto y respetarlas durante el uso del producto Deber n tenerse en cuenta todas las dem s informaciones de seguridad como p ej las referentes a la protecci n de personas que encontrar n en el cap tulo correspondiente de la documentaci n del producto y que tambi n son de obligado cumplimiento En las presentes informaciones de seguridad se recogen todos los objetos que distribuye el grupo de empresas Rohde 8 Schwarz bajo la denominaci n de producto entre ellos tambi n aparatos instalaciones as como toda clase de accesorios S mbolos y definiciones de seguridad l Aviso punto de Atenci n en Peligro de Adver Conexi n a Conexi n Conexi n Aviso Cuidado peligro general el manejo de choque tencia conductor de a tierra amasa en el manejo de dispositivos el ctrico superficie protecci n dispositivos Observanla d de caliente sensible
49. n rsphdt ConfigureRespPort This makes it possible to set indi vidual values for each port The result of the signal evaluation of a channel is 1 if the input level is greater than the High threshold The result of the signal evaluation of a channel is 0 if the input level is less than the Low threshold If the input level is between the thresholds Forbidden Zone 1 re turned as the result ROHDE amp SCHWARZ Funktionsbeschreibung 5 14 High Speed Digital Test Module R amp S TS PHDT 5 6 Time settings for data output Two functions are available to configure the timing of the stimulus channels during pattern execution Function rsphdt ConfigureStimTiming adjusts the trigger delay and pat tern set period The trigger delay 1 the wait time between the trigger event and the output of the first pattern The pattern set period is the time during which a pattern is present If formatting for the stimulus sig nal RTZ return to zero mode is deactivated this time also defines the duration of a High and Low level The selected pattern set period cor responds to the set period of the clock signals STIM_CLK and AUX_CLK on the front side connector Function rsphdt ConfigureReturnToZeroMode can be used to define the time response of the channels when RTZ mode is activated The first parameter determines the delay of the active signal edge in reference to the beginning of the pattern The second p
50. nt personal injury e g due to laser beams 1171 0000 42 05 00 Page 4 Basic Safety Instructions Repair and service 1 The product may be opened only by authorized specially trained personnel Before any work is performed on the product or before the product is opened it must be disconnected from the AC supply network Otherwise personnel will be exposed to the risk of an electric shock Adjustments replacement of parts maintenance and repair may be performed only by electrical experts authorized by Rohde amp Schwarz Only original parts may be used for replacing parts relevant to safety e g power switches power transformers fuses A safety test must always be performed after parts relevant to safety have been replaced visual inspection PE conductor test insulation resistance measurement leakage current measurement functional test This helps ensure the continued safety of the product Batteries and rechargeable batteries cells If the information regarding batteries and rechargeable batteries cells is not observed either at all or to the extent necessary product users may be exposed to the risk of explosions fire and or serious personal injury and in some cases death Batteries and rechargeable batteries with alkaline electrolytes e g lithium cells must be handled in accordance with the EN 62133 standard 1 Cells must not be taken apart or crushed 2 Cells or batteries must not be exposed to heat or fire Sto
51. of failed channels corresponds to the number of bits set to 1 in that result The function can also be called during execution If execution was started with function ROHDE amp SCHWARZ Funktionsbeschreibung 5 20 High Speed Digital Test Module R amp S TS PHDT rsphdt InitiateExecutionEx the parameter Reset Flag de termines whether the register will be reset for start Function rsphdt InitiateExecution always sets the register of the failed channels to zero before execution starts 5 11 4 Number of failed channels Function rsphdt_FetchFailedChannelCount returns the number of channels that had a Fail in at least one pattern The function can also be called during execution If execution was started with function rsphdt InitiateExecutionEX the parameter Reset Flag determines whether the counter will be reset for start Function rsphdt_InitiateExecution always sets the number of failed channels to zero before execution starts 5 11 5 Failed patterns During execution of a pattern set the indices of failed patterns are re corded by blocks This makes it possible to have access to errors that occurred regardless of the recording type measured values or error in formation The result data does not need to be transferred to the PC and browsed This error memory can be read with function rsphdt FetchFailedPatternGroup Each time the function is
52. orresponding output by means of an analog switch This makes it possible to read back the outputs or to read in a test object response when the outputs are switched to Tri State The circuit is set up by means of function rsphdt ConnectInOut 5 21 ROHDE amp SCHWARZ Funktionsbeschreibung 5 22 High Speed Digital Test Module R amp S TS PHDT 5 14 Generating a static pattern Output of a pattern is possible even if memory on the module has not previously been written with function rsphdt SetDigitalOuputState Timing and trigger settings have no effect on execution of this function The transferred pattern ap pears immediately at the output Transferring a bit mask makes it pos sible to address individual channels selectively This function cannot be performed if sequence control for stimulus has status Waiting or Running 5 15 Querying the inputs The state of the inputs IN1to IN32 on the module can be queried with drive function rsphdt GetDigitalInputState The coding of the status in both return values corresponds to the coding in results mem ory in Measurement values recording mode forbidden logic level bit Function zone bit 0 0 Low measured 0 1 High measured 1 0 reserved 1 1 Forbidden Zone measured Table 5 9 Coding of return values This function can not be performed if the sequence control for the re cording unit has status Waiting or Running
53. os productos de la clase de protecci n con alimentaci n m vil y enchufe individual solamente podr n enchufarse a tomas de corriente con contacto de seguridad y con conductor de protecci n conectado Queda prohibida la interrupci n intencionada del conductor de protecci n tanto en la toma de corriente como en el mismo producto La interrupci n puede tener como consecuencia el riesgo de que el producto sea fuente de choques el ctricos Si se utilizan cables alargadores o regletas de enchufe deber garantizarse la realizaci n de un examen regular de los mismos en cuanto a su estado t cnico de seguridad Si el producto no est equipado con un interruptor para desconectarlo de la red se deber considerar el enchufe del cable de conexi n como interruptor En estos casos se deber asegurar que el enchufe siempre sea de f cil acceso de acuerdo con la longitud del cable de conexi n aproximadamente 2 m Los interruptores de funci n o electr nicos no son aptos para el corte de la red el ctrica Si los productos sin interruptor est n integrados en bastidores o instalaciones se deber colocar el interruptor en el nivel de la instalaci n No utilice nunca el producto si est da ado el cable de conexi n a red Compruebe regularmente el correcto estado de los cables de conexi n a red Aseg rese mediante las medidas de protecci n y de instalaci n adecuadas de que el cable de conexi n a red no pueda ser da ado o de que nadie p
54. ose Doing so can cause short circuits inside the product and or electric shocks fire or injuries Unless specified otherwise products are not liquid proof see also section Operating states and operating positions item 1 Therefore the equipment must be protected against penetration by liquids If the necessary precautions are not taken the user may suffer electric shock or the product itself may be damaged which can also lead to personal injury Never use the product under conditions in which condensation has formed or can form in or on the product e g if the product has been moved from a cold to a warm environment Penetration by water increases the risk of electric shock Prior to cleaning the product disconnect it completely from the power supply e g AC supply network or battery Use a soft non linting cloth to clean the product Never use chemical cleaning agents such as alcohol acetone or diluents for cellulose lacquers Operation 1 Operating the products requires special training and intense concentration Make sure that persons who use the products are physically mentally and emotionally fit enough to do so otherwise injuries or material damage may occur It is the responsibility of the employer operator to select suitable personnel for operating the products Before you move or transport the product read and observe the section titled Transport As with all industrially manufactured goods the use of substance
55. p Schwarz se producen reacciones al rgicas como p ej irritaciones cut neas estornudos continuos enrojecimiento de la conjuntiva o dificultades respiratorias debe avisarse inmediatamente a un m dico para investigar las causas y evitar cualquier molestia o da o a la salud Antes de la manipulaci n mec nica y o t rmica o el desmontaje del producto debe tenerse en cuenta imprescindiblemente el cap tulo Eliminaci n punto 1 1171 0000 42 05 00 Page 10 5 Informaciones elementales de seguridad Ciertos productos como ej las instalaciones de radiocomunicaci n RF pueden a causa de su funci n natural emitir una radiaci n electromagn tica aumentada Deben tomarse todas las medidas necesarias para la protecci n de las mujeres embarazadas Tambi n las personas con marcapasos pueden correr peligro a causa de la radiaci n electromagn tica El empresario operador tiene la obligaci n de evaluar y se alizar las reas de trabajo en las que exista un riesgo elevado de exposici n a radiaciones Tenga en cuenta que en caso de incendio pueden desprenderse del producto sustancias t xicas gases l quidos etc que pueden generar da os a la salud Por eso en caso de incendio deben usarse medidas adecuadas como p ej m scaras antig s e indumentaria de protecci n En caso de que un producto Rohde amp Schwarz contenga un producto l ser ej un lector de CD DVD no debe usarse ninguna otra configuraci n o funci n a
56. parte de las descritas en la documentaci n del producto a fin de evitar lesiones p ej debidas a irradiaci n l ser Reparaci n y mantenimiento 1 El producto solamente debe ser abierto por personal especializado con autorizaci n para ello Antes de manipular el producto o abrirlo es obligatorio desconectarlo de la tensi n de alimentaci n para evitar toda posibilidad de choque el ctrico El ajuste el cambio de partes el mantenimiento y la reparaci n deber n ser efectuadas solamente por electricistas autorizados por Rohde 8 Schwarz Si se reponen partes con importancia para los aspectos de seguridad p ej el enchufe los transformadores o los fusibles solamente podr n ser sustituidos por partes originales Despu s de cada cambio de partes relevantes para la seguridad deber realizarse un control de seguridad control a primera vista control del conductor de protecci n medici n de resistencia de aislamiento medici n de la corriente de fuga control de funcionamiento Con esto queda garantizada la seguridad del producto Bater as y acumuladores o celdas Si no se siguen o se siguen de modo insuficiente las indicaciones en cuanto a las bater as y acumuladores o celdas pueden producirse explosiones incendios y o lesiones graves con posible consecuencia de muerte El manejo de bater as y acumuladores con electrolitos alcalinos p ej celdas de litio debe seguir el est ndar EN 62133 1 2 No deben desmonta
57. product documentation could result in personal injury or death eo Do not place the product on heat generating devices such as radiators or fan heaters The ambient temperature must not exceed the maximum temperature specified in the product documentation or in the data sheet Product overheating can cause electric shock fire and or serious personal injury or death 1171 0000 42 05 00 Page 2 Basic Safety Instructions Electrical safety If the information on electrical safety is not observed either at all to the extent necessary electric shock fire and or serious personal injury or death may occur 1 Prior to switching on the product always ensure that the nominal voltage setting on the product matches the nominal voltage of the AC supply network If a different voltage is to be set the power fuse of the product may have to be changed accordingly 2 In the case of products of safety class with movable power cord and connector operation is permitted only on sockets with an earthing contact and protective earth connection 3 Intentionally breaking the protective earth connection either in the feed line or in the product itself is not permitted Doing so can result in the danger of an electric shock from the product If extension cords or connector strips are implemented they must be checked on a regular basis to ensure that they are safe to use 4 If the product does not have a power switch for disconnection from the AC supply
58. que las palabras de se al aqu descritas sean utilizadas siempre solamente en combinaci n con la correspondiente documentaci n del producto y solamente en combinaci n con el producto correspondiente La utilizaci n de las palabras de se al en combinaci n con productos o documentaciones que no les correspondan puede llevar a interpretaciones equivocadas y tener por consecuencia da os en personas u objetos Estados operativos y posiciones de funcionamiento El producto solamente debe ser utilizado seg n lo indicado por el fabricante respecto a los estados operativos y posiciones de funcionamiento sin que se obstruya la ventilaci n Sino se siguen las indicaciones del fabricante pueden producirse choques el ctricos incendios y o lesiones graves con posible consecuencia de muerte En todos los trabajos deber n ser tenidas en cuenta las normas nacionales y locales de seguridad del trabajo y de prevenci n de accidentes 1 Si no se convino de otra manera es para los productos Rohde amp Schwarz v lido lo que sigue como posici n de funcionamiento se define por principio la posici n con el suelo de la caja para abajo modo de protecci n IP 2X grado de suciedad 2 categor a de sobrecarga el ctrica 2 uso solamente en estancias interiores utilizaci n hasta 2000 m sobre el nivel del mar transporte hasta 4500 m sobre el nivel del mar Se aplicar una tolerancia de 10 sobre el voltaje nominal y de 5 sobre la frecuencia nominal N
59. r atenerse a todas las indicaciones informaciones de seguridad y notas de alerta El grupo de empresas Rohde amp Schwarz est siempre a su disposici n en caso de que tengan preguntas referentes a estas informaciones de seguridad Adem s queda en la responsabilidad del usuario utilizar el producto en la forma debida Este producto est destinado exclusivamente al uso en la industria y el laboratorio o si ha sido expresamente autorizado para aplicaciones de campo y de ninguna manera deber ser utilizado de modo que alguna persona cosa pueda sufrir da o El uso del producto fuera de sus fines definidos o sin tener en cuenta las instrucciones del fabricante queda en la responsabilidad del usuario El fabricante no se hace en ninguna forma responsable de consecuencias a causa del mal uso del producto 1171 0000 42 05 00 Page 6 Informaciones elementales de seguridad Se parte del uso correcto del producto para los fines definidos si el producto es utilizado conforme a las indicaciones de la correspondiente documentaci n del producto y dentro del margen de rendimiento definido ver hoja de datos documentaci n informaciones de seguridad que siguen El uso del producto hace necesarios conocimientos t cnicos y ciertos conocimientos del idioma ingl s Por eso se debe tener en cuenta que el producto solo pueda ser operado por personal especializado o personas instruidas en profundidad con las capacidades correspondientes Si fuera necesaria indu
60. rage in direct sunlight must be avoided Keep cells and batteries clean and dry Clean soiled connectors using a dry clean cloth 3 Cells or batteries must not be short circuited Cells or batteries must not be stored in a box or in a drawer where they can short circuit each other or where they can be short circuited by other conductive materials Cells and batteries must not be removed from their original packaging until they are ready to be used 4 Keep cells and batteries out of the hands of children If a cell or a battery has been swallowed seek medical aid immediately 5 Cells and batteries must not be exposed to any mechanical shocks that are stronger than permitted 6 Ifa cell develops a leak the fluid must not be allowed to come into contact with the skin or eyes If contact occurs wash the affected area with plenty of water and seek medical aid 7 Improperly replacing or charging cells or batteries that contain alkaline electrolytes e g lithium cells can cause explosions Replace cells or batteries only with the matching Rohde amp Schwarz type see parts list in order to ensure the safety of the product 8 Cells and batteries must be recycled and kept separate from residual waste Rechargeable batteries and normal batteries that contain lead mercury or cadmium are hazardous waste Observe the national regulations regarding waste disposal and recycling Transport 1 The product may be very heavy Therefore the product must
61. rse abrirse ni triturarse las celdas Las celdas o bater as no deben someterse a calor ni fuego Debe evitarse el almacenamiento a la luz directa del sol Las celdas y bater as deben mantenerse limpias y secas Limpiar las conexiones sucias con un pa o seco y limpio Las celdas o bater as no deben cortocircuitarse Es peligroso almacenar las celdas o bater as en estuches o cajones en cuyo interior puedan cortocircuitarse por contacto rec proco o por contacto con otros materiales conductores No deben extraerse las celdas o bater as de sus embalajes originales hasta el momento en que vayan a utilizarse Mantener bater as y celdas fuera del alcance de los ni os En caso de ingesti n de una celda o bater a avisar inmediatamente a un m dico Las celdas o bater as no deben someterse a impactos mec nicos fuertes indebidos 1171 0000 42 05 00 Page 11 Informaciones elementales de seguridad 6 En caso de falta de estanqueidad de una celda el l quido vertido no debe entrar en contacto con la piel ni los ojos Si se produce contacto lavar con agua abundante la zona afectada y avisar a un m dico En caso de cambio o recarga inadecuados las celdas o bater as que contienen electrolitos alcalinos p ej las celdas de litio pueden explotar Para garantizar la seguridad del producto las celdas o bater as solo deben ser sustituidas por el tipo Rohde 8 Schwarz correspondiente ver lista de recambios Las bater as y celdas deben
62. s XTI1 and XTI2 on the front connector are available as trigger inputs The R amp S TS PHDT module contains a large memory for stimulus ref erence and result data This memory can contain multiple pattern sets atthe same time The pattern sets can then be repeatedly executed for different tests Cyclic downloading of pattern sets is eliminated thus saving test time The input signals are compared with reference data in real time when the pattern sets are executed Depending on the recording mode se lected either the recorded pattern or the results of the comparison are stored in results memory The registers on the module holds the number of errors and channels that have failed Test time can also be saved in this case since there is often no need to upload the exten sive data in results memory as only the error registers are evaluated After a pattern set has been executed outputs OUT1 OUT32 retain the last pattern to be executed If you would like the outputs to become Funktionsbeschreibung ROHDE amp SCHWARZ Funktionsbeschreibung 5 2 High Speed Digital Test Module R amp S TS PHDT inactive after execution is complete a Tri State pattern must be explic appended at the end It is also possible to set the channels statically after execution is complete 5 1 2 Simple dynamic digital test Stimulus pattern set for 32 output channels Reference pattern set for 32 input channels e The pattern duration for th
63. s a la documentacion elevado electrostatica del producto ESD iO lo ca Tensi n de Indicaci n de Corriente Corriente alterna Corriente El aparato est protegido alimentaci n de estado de continua DC AC continua en su totalidad por un PUESTA EN espera Corriente alterna aislamiento doble MARCHA Standby DC AC reforzado PARADA 1171 0000 42 05 00 Page 7 Informaciones elementales de seguridad Palabras de se al su significado En la documentaci n del producto se utilizan las siguientes palabras de se al con el fin de advertir contra riesgos y peligros PELIGRO identifica un peligro inminente con riesgo elevado que 4 PELIGRO provocar muerte o lesiones graves si no se evita ADVERTENCIA identifica un posible peligro con riesgo medio de ADVERTENCIA provocar muerte o lesiones graves si no se evita ATENCI N identifica un peligro con riesgo reducido de provocar ATENCI N lesiones leves moderadas si se evita AVISO indica la posibilidad de utilizar mal el producto y como consecuencia da arlo En la documentaci n del producto se emplea de forma sin nima el t rmino CUIDADO Las palabras de se al corresponden a la definici n habitual para aplicaciones civiles en el rea econ mica europea Pueden existir definiciones diferentes a esta definici n en otras reas econ micas o en aplicaciones militares Por eso se deber tener en cuenta
64. s memory eere 5 7 Table 5 3 Reference memory coding 5 7 Table 5 4 Coding of measurement values in results memory 5 8 Table 5 5 Coding of results memory for Pass Fail and FBZ information 5 9 Table 5 6 Trigger SOU COS wc 5 17 Table 5 7 Trigger QU PULS t 5 21 Table 5 8 Events for generating a trigger 5 21 Table 5 9 Coding of return values nen 5 22 Table 5 10 Glock signals on the X 10 5 23 Table 7 1 Driver installation R amp S TS PHDT 7 1 Table 7 2 Input formats for pattern ss 7 3 Table 8 1 Observations about the LED test 8 1 Table 8 2 Observations about the power on test 8 2 Table 9 1 Pin assignment for connector 1 nnmnnn 9 1 Table 9 2 Pin assignment for connector X20 is 9 2 Table 9 3 Pin assignment for connector X10 view front panel 9 3 Table 9 4 Pin assignment for connector X30 9 5 amp SCHWARZ Tables High Speed Digital Test Module R amp S TS PHDT 3rd Issue 04 09 3rd Issue 04 09 High Speed Digital Test Module R amp S TS PHDT amp SCHWARZ 1 Usage 1 1 General The High Speed Digital Test Modul
65. s that induce an allergic reaction allergens such as nickel cannot be generally excluded If you develop an allergic reaction such as a skin rash frequent sneezing red eyes or respiratory difficulties when using a Rohde amp Schwarz product consult a physician immediately to determine the cause and to prevent health problems or stress Before you start processing the product mechanically and or thermally or before you take it apart be sure to read and pay special attention to the section titled Waste disposal item 1 Depending on the function certain products such as RF radio equipment can produce an elevated level of electromagnetic radiation Considering that unborn babies require increased protection pregnant women must be protected by appropriate measures Persons with pacemakers may also be exposed to risks from electromagnetic radiation The employer operator must evaluate workplaces where there is a special risk of exposure to radiation and if necessary take measures to avert the potential danger Should a fire occur the product may release hazardous substances gases fluids etc that can cause health problems Therefore suitable measures must be taken e g protective masks and protective clothing must be worn If a laser product e g a CD DVD drive is integrated into a Rohde amp Schwarz product absolutely no other settings or functions may be used as described in the product documentation The objective is to preve
66. sassembly may be hazardous to your health National waste disposal regulations must be observed 2 If handling the product releases hazardous substances or fuels that must be disposed of in a special way e g coolants or engine oils that must be replenished regularly the safety instructions of the manufacturer of the hazardous substances or fuels and the applicable regional waste disposal regulations must be observed Also observe the relevant safety instructions in the product documentation The improper disposal of hazardous substances or fuels can cause health problems and lead to environmental damage Informaciones elementales de seguridad Es imprescindible leer y observar las siguientes instrucciones e informaciones de seguridad principio del grupo de empresas Rohde amp Schwarz consiste en tener nuestros productos siempre al dia con los estandares de seguridad y de ofrecer a nuestros clientes el maximo grado de seguridad Nuestros productos y todos los equipos adicionales son siempre fabricados y examinados seg n las normas de seguridad vigentes Nuestro sistema de garant a de calidad controla constantemente que sean cumplidas estas normas El presente producto ha sido fabricado y examinado seg n el certificado de conformidad adjunto de la UE y ha salido de nuestra planta en estado impecable seg n los est ndares t cnicos de seguridad Para poder preservar este estado y garantizar un funcionamiento libre de peligros el usuario debe
67. so de un accidente lesiones u otra clase de da os Eliminaci n 1 Si se trabaja de manera mec nica y o t rmica cualquier producto o componente m s all del funcionamiento previsto pueden liberarse sustancias peligrosas polvos con contenido de metales pesados como p ej plomo berilio o n quel Por eso el producto solo debe ser desmontado por personal especializado con formaci n adecuada Un desmontaje inadecuado puede ocasionar da os para la salud Se deben tener en cuenta las directivas nacionales referentes a la eliminaci n de residuos En caso de que durante el trato del producto se formen sustancias peligrosas o combustibles que deban tratarse como residuos especiales p ej refrigerantes o aceites de motor con intervalos de cambio definidos deben tenerse en cuenta las indicaciones de seguridad del fabricante de dichas sustancias y las normas regionales de eliminaci n de residuos Tenga en cuenta tambi n en caso necesario las indicaciones de seguridad especiales contenidas en la documentaci n del producto La eliminaci n incorrecta de sustancias peligrosas o combustibles puede causar da os a la salud o da os al medio ambiente 1171 0000 42 05 00 Page 12 Certified Quality System DIN EN ISO 9001 2000 DIN EN 9100 2003 2004 DIN EN ISO 14001 DOS REG NO 001954 QM UM QUALITATSZERTIFIKAT Sehr geehrter Kunde Sie haben sich f r den Kauf eines Rohde amp Schwarz Produktes ent schieden Hiermit erhal
68. static ViUInt32 s RefCtrl PATTERN COUNT 2 2 2 0 0 0 0 0 static ViUInt32 s RespLvl PATTERN COUNT static ViUInt32 s RespCtrl PATTERN COUNT int main int argc char argv Vilnt32 idStim idRef exeResult ViSession vi ViStatus status 3rd Issue 04 09 3rd Issue 04 09 ROHDE amp SCHWARZ High Speed Digital Test Module R amp S TS PHDT Software open a session to the device driver The resource descriptor depends on the slot number of the module and must be adapted to the target system status rsphdt_InitWithOptions PXI1 11 0 INSTR VI_TRUE VI_TRUE Simulate 0 RangeCheck 1 amp vi stimulus data download nly high low pattern gt VI_NULL for tri state information ed status rsphdt LoadData vi RSPHDT VAL DATA STIM PATTERN COUNT s StimLvl VI NULL amp idStim reference data download y status rsphdt LoadData vi RSPHDT VAL DATA REF PATTERN COUNT s RefLvl s RefCtrl amp idRef set collection mode to data status rsphdt ConfigureCollectionMode vi RSPHDT VAL COLLECT DATA configure stimulus ports voltage high s Da voltage low 0 0 D 0 current limit high level current limit low level status rsphdt ConfigureStimPort vi RSPHDT MASK PORT ALL 50 0 0 D Di 4 0 1 0 1 configure response ports vol
69. structions Always read through and comply with the following safety instructions All plants and locations of the Rohde amp Schwarz group of companies make every effort to keep the safety standards of our products up to date and to offer our customers the highest possible degree of safety Our products and the auxiliary equipment they require are designed built and tested in accordance with the safety standards that apply in each case Compliance with these standards is continuously monitored by our quality assurance system The product described here has been designed built and tested in accordance with the attached EC Certificate of Conformity and has left the manufacturer s plant in a condition fully complying with safety standards To maintain this condition and to ensure safe operation you must observe all instructions and warnings provided in this manual If you have any questions regarding these safety instructions the Rohde amp Schwarz group of companies will be happy to answer them Furthermore it is your responsibility to use the product in an appropriate manner This product is designed for use solely in industrial and laboratory environments or if expressly permitted also in the field and must not be used in any way that may cause personal injury or property damage You are responsible if the product is used for any intention other than its designated purpose or in disregard of the manufacturer s instructions The manufacturer sh
70. tage high threshold 2 voltage low threshold 0 WI status rsphdt ConfigureRespPort vi RSPHDT MASK PORT ALL 2 4 0 8 7 5 ROHDE amp SCHWARZ Software High Speed Digital Test Module R amp S TS PHDT configure stimulus timing trigger delay 0 0 s pattern period 1 0e 6 s i status rsphdt ConfigureStimTiming vi 0 0 1 0e 6 configure response timing trigger delay 0 0 s pattern period 1 0e 6 s response delay 0 5e 6 7 6 SCH status rsphdt ConfigureRespTiming vi 0 0 1 0 6 0 5 6 trigger source immidiate is default after reset start execution of stimulus and response part status rsphdt InitiateExecution vi idStim idRef wait until execution has finished timeout 10 ms status rsphdt WaitUntilExecutionComplete vi RSPHDT VAL BOTH 10 get the execution result tatus rsphdt FetchExecutionResult vi amp exeResult un if exeResult RSPHDT VAL RESULT PASS test failed Vilnt32 failedPatternCount readRespPatternCnt ViUInt32 failedChannels fetch some execution results status rsphdt FetchFailedPatternCount vi amp failedPatternCount status rsphdt FetchFailedChannels vi amp failedChannels fetch all the measured pattern status rsphdt FetchData vi idRef RSPHDT VAL DATA RESP O PATTERN_COUNT s RespLvl s RespCtrl
71. ten Sie ein nach modernsten Fertigungsme thoden hergestelltes Produkt Es wurde nach den Regeln unseres Managementsystems entwickelt gefertigt und gepr ft Das Rohde amp Schwarz Management system ist zertifiziert nach DIN EN ISO 9001 2000 DIN EN 9100 2003 DIN EN ISO 14001 2004 1171 0200 11 03 00 CERTIFICATE OF QUALITY Dear Customer you have decided to buy a Rohde amp Schwarz product You are thus as sured of receiving a product that is manufactured using the most modern methods available This product was developed manufactured and tested in compliance with our quality mana gement system standards The Rohde amp Schwarz quality management system is certified according to DIN EN ISO 9001 2000 DIN EN 9100 2003 DIN EN ISO 14001 2004 CERTIFICAT DE QUALITE Cher Client vous avez choisi d acheter un produit Rohde amp Schwarz Vous disposez donc d un produit fabriqu d apr s les m thodes les plus avanc es Le d veloppement la fabrication et les tests respectent nos normes de ges tion qualit Le syst me de gestion qualit de Rohde amp Schwarz a t homologu conform ment aux normes DIN EN ISO 9001 2000 DIN EN 9100 2003 DIN EN ISO 14001 2004 ROHDE amp SCHWARZ PD 5213 8744 99 01 00 May 2007 Address List Headquarters Plants and Subsidiaries Headquarters ROHDE amp SCHWARZ GmbH amp Co KG M hldorfstra amp e 15 D 81671 M nchen P 0 Box 80 14 69 D 81614 M n
72. ueda ser da ado por l p ej al tropezar o por un choque el ctrico Solamente est permitido el funcionamiento en redes de alimentaci n TN TT aseguradas con fusibles de 16 A como m ximo utilizaci n de fusibles de mayor amperaje solo previa consulta con el grupo de empresas Rohde 8 Schwarz Nunca conecte el enchufe en tomas de corriente sucias o llenas de polvo Introduzca el enchufe por completo y fuertemente en la toma de corriente La no observaci n de estas medidas puede provocar chispas fuego y o lesiones No sobrecargue las tomas de corriente los cables alargadores o las regletas de enchufe ya que esto podr a causar fuego o choques el ctricos En las mediciones en circuitos de corriente con una tensi n gt 30 V se deber n tomar las medidas apropiadas para impedir cualquier peligro p ej medios de medici n adecuados seguros limitaci n de tensi n corte protector aislamiento etc Para la conexi n con dispositivos inform ticos como un PC o un ordenador industrial debe comprobarse que stos cumplan los est ndares IEC60950 1 EN60950 1 o IEC61010 1 EN 61010 1 v lidos en cada caso A menos que est permitido expresamente no retire nunca la tapa ni componentes de la carcasa mientras el producto est en servicio Esto pone a descubierto los cables y componentes el ctricos y puede causar lesiones fuego o da os en el producto 1171 0000 42 05 00 Page 9 12 13 14 15 16 17 18
73. y to the format in the memory banks This makes it pos sible to transfer the data to the module with optimum speed It is also necessary to be able to modify data that is already loaded into the mod ule The function rsphdt UpdateData is available for this purpose Itis able to overwrite portions of the data on the module It also has two 32 bit arrays as parameters in addition to the ID of the data record the Start index and the Number of patterns The ID serves to iden tify the data record and is assigned by the function rsphdt LoadData Pattern sets that are no longer required can be removed from memory with the function rsphdt_DiscardData 3rd Issue 04 09 3rd Issue 04 09 amp SCHWARZ High Speed Digital Test Module R amp S TS PHDT Funktionsbeschreibung NOTE Deleting data records in some cases causes gaps in memory on the R amp S TS PHDT module that will be refilled by pattern sets of the same size or smaller In unfavourable cases it may happen that the gaps cannot be filled in and therefore the full extent of memory can no longer be used Deleting all data records or call ing the function rsphdt_reset makes all of memory available again Two 32 bit arrays must be provided in the user program for the results data The content of the results memory banks is transferred to these two arrays by means of the function rsphdt_FetchData upload The data quantity can either

USER MANUAL - Rohde & Schwarz

Contents

Download Pdf Manuals

Related Search

Related Contents

USER MANUAL - Rohde &amp; Schwarz

Contents

Download Pdf Manuals

Related Search

Related Contents

USER MANUAL - Rohde & Schwarz