Home

Installation Instructions & Owners Manual

image

Contents

1. Belmont is not responsible for any changes made by the manufacturer in the chemical composition of the cleaning solutions listed above which may affect the surface finish after application Cambria Quartz Surface Cleaning Care Maintenance Cambria is care free therefore no sealing buffing polishing or reconditioning is required Using soap and water is sufficient to clean the Cambria Quartz surface Rev 121907
2. See Figure 2 FIGURE 2 x 2 Places A UNLOCK TYPICAL CAM PIN SETUP Page 2C Dispenser Flipping Assembly Instructions Model E 2L Step 3 With the cabinet laying on its back turn each of 2 cams on the bottom of the cabinet counter clockwise approx 4 turn See Figure 3 Step 4 Using a rubber mallet tap the end of the cabinet on the side that you earlier lossened the cams on the backside See Figure 4A Remove end panel Make sure the cam pin and dowels remain seated in the main body and do not come off with the end panel you remove If they remain intact within the end panel remove them and insert them into the proper related hole within the main body See Figure 4B Step 5 Using a rubber mallet tap bottom piece outwards to the open end See Figure 5A Remove the bottom piece from the main body See Figure 5B Make sure the cam pin and dowels remain seated in the bottom piece being removed and do not come off in the end panel If they remain intact within the end panel remove them and insert them into the proper related hole within the main body as mentioned in Step 4 x 2 Places FIGURE 3 Page 3C Dispenser Flipping Assembly Instructions Model E 2L Step 6 Flip bottom piece around 180 See Figure GA And set into position making sure to align the cam pins and dowels into the proper holes Once in position use t
3. Installation Instructions E Series Dental Cabinetry amp Owners Manual Model E 2L 1 emong Consumer Please retain these instructions for future use 1631 Dr Martin Luther King Drive St Louis MO 63106 314 231 7383 888 833 3682 Fax 314 621 2296 www belmontequip com Detail Drawings Model E 2L GLOVE TISSUE DISPENSERS Ess LLY ISOMETRIC VIEW RIGHT SIDE VIEW CUP amp TOWEL DISPENSERS AYYA AYN 8 Z 8S wu 6bl AVA AVW 9d wwo LL TOP VIEW FRONT VIEW Lu O lt x O fe u JE z 2 O 4 lt w LL O l N LJ Description Rev 100207 Assembly Instructions Model E 2L E 2L With Cambria Top Assembly Instructions Component Identification uke Component Identification E 2L Wall Mount Storage Cabinet Lower E 2L Cambria Top C Cup Dispenser D Towel Dispenser Rev 100407 Page 1B Step 1 Locate where the cabinet is to be mounted on the wall 54 from the floor to the top of the cabinet is the suggested location See Figure 1 Open the doors and at the inside corners drill a 3 16 dia hole through the back panel this will be the wall mounting screw locations Important Before drilling the holes for the wall mounting you will need to decide how best to fasten it to the wall depending on the walls construction Its recommended that you fasten into structural members where possible such as wood or metal studs You may screw d
4. another set of instructions you may return to that set of instructions and continue with latest step completed Step 11 To install handles you must drill thru the partially drilled blind holes in the inside face of the doors using a z dia drill bit See Figure 11A FIGURE 11A Note Make sure at this point you have the proper configuration of which sides the cup towel dispensers are located and the glove tissue dispensers door location always opposite the cup towel cutout location Using the machine screws that come with the handles attach both handles to the doors See Figure 11B Attach magnet strike plate to the glove dispenser door using 2 6 x 3 screws and attach the magnet to the top panel using 2 6 x Screws See Figure 11C zj Installation Complete FIGURE 11C Page 5C Hinge Adjustments Model E 2L Hinge Adjustment For Standard Doors Select base plates have cam adjust ment access through arm Rev 100507 Surface Cleaning Model E Series all models Quolis Cabinetry Systems Laminate Surfaces Cleaning Instructions The disinfectant solution should be applied in accordance with the instructions provided by the manufacturer The following solutions are recommended for laminate surfaces they may also be used on metal and glass surfaces Product Manufacturer Birex Biotrol International Kodak Clinasept Kodak Foaming Disinfectant Catalogue 829 5230
5. e top of the cabinet Place the Cambria top onto the top of the cabinet and press down to properly seat the top See Figure 6 FIGURE 6 Step 7 Open the left door and insert the cup dispenser C through the hole and the towel dispenser D through the rectangular cutout See Figure 7 an a FIGURE 7 L FIGURE Installation Complete Dispenser Flipping Assembly Instructions Model E 2L E 2L Dispenser Flipping Instructions Component Identification 00 oo Note If the glove tissue amp paper towel cup dispensers need to be flipped to the opposite sides use these instructions SS 0 Door handles not shown If handles are already mounted you cannot flip the cup towel dispenser and the glove ttissue dispenser due to the doors needing to be flipped causing the handles to be at the top instead of the bottom of the doors Component Identification A2 E 2L Wall Mount Storage Cabinet Lower C Cup Dispenser D Towel Dispenser Rev 121907 Dispenser Flipping Assembly Instructions Model E 2L Step 1 SHEL EARS TO RELEASE Remove doors by opening and pulling up on the tab at the HINGE end of each hinge base plate mounted on the inside of the cabinet See Figure 1 Step 2 From the back side of the cabinet turn 2 cams on only one end of cabinet counter clockwise approx 4 turn
6. he rubber mallot to properly seat all cams pins See Figure 6B NOTE THE ORDER IN WHICH THE QUICKFIT CAM AND PIN GO TOGETHER IS VERY IMPORTANT INSTALL THE CAMS INTO THE BOARD WITH THE PHILLIPS SLOT FACING UP AND THE ARROW POINTING TO THE EDGE THEN INSERT THE PIN INTO THE CAM IF THE CAM AND PIN ARE NOT ASSEMBLED IN THIS MANNER IT WILL NOT CLAMP THE BOARDS TIGHTLY Step 7 Set the end panel into position and tap into place using the rubber mallet See Figure 7 Step 8 Lock both cams into position at the bottom pieces left and right end by turning clockwise approx 3 turn See Figure 8 Rev 100407 x 2 Places FIGURE 8 Page 4C Dispenser Flipping Assembly Instructions Model E 2 Step 9 From the back side of the cabinet turn 2 cams the ones loosened GZ in step 2 clockwise approx 1 turn See Figure 9 i Noe BACK FIGURE 9 LOCK Step 10 x 2 Places Mount the doors on the opposite ends they were removed from in Step 1 Replace the doors by lining up the hinge and hinge plate then snap the hinge in place See separate instruction page regarding adjusting the hinges if the doors ge are not properly aligned ZAL TS URE 10 The door with the glove tissue opening shouild be opposite e of the cutouts for the cup towel dispenser See Figure 10 FIG Door handles may be installed at this point continue w Step 11 or if you were referred to this instruction set by
7. irectly into studs with the appropriate screw type Mounting the cabinet to drywall only you may use the manufacturer recommended fasteners four zip it screws with 8 x 1 1 2 pan head screws or four molly screws Step 2 Hold cabinet with an assistants help up to the wall at the location to be mounted making sure it is level Mark the wall through the 4 holes previously drilled If screwing directly into a structural member you may do so now by drilling small pilot holes for the appropriate screws Skip to Step 3 If you will be using zip it or molly screws you will need to drill appropriate sized holes for the type of fastener at the locations marked Zip it screws Drive the zip it screws into hole locations until the top is flush with the drywall See Figure 2B Molly screws Drill 3 8 holes into the drywall at desired locations and insert the molly inserts into the holes until the top is flush with the drywall See Figure 2C Fully thead the molly screws into the molly inserts to compress amp secure them to the drywall then remove the screws See Figure 2D Assembly Instructions Model E 2L 00 FIGURE 1 54 ABOVE FLOOR RECOMMENDED HN aati a KC zip it screw with 8 x 1 1 2 pan head screw molly screw IN MARK FASTENER LOCATIONS FIGURE 2A A a 4 FIGURE 2B FIGURE 2C FIGURE 2D Page 2B Assembly Instr
8. uctions Model E 2L Step 3 If the glove tissue amp paper towel cup dispensers need to be flipped to the opposite sides See Figure 3 refer to E 2U Dispenser Flipping Instructions Perform this task now if so desired Step 4 To install handles you must drill thru the partially drilled blind holes in the inside face of the doors using a 25 dia drill bit See Figure 4A Note Make sure at this point you have the proper configuration of FIGURE 4A which sides the cup towel dispensers are located and the glove tissue dispensers door location always opposite the cup towel cutout location Using the machine screws that come with the handles attach both 3 DL handles to the doors See Figure 4B A gt Attach magnet strike plate to the glove dispenser door using 2 6 x 3 screws and attach the magnet to the top panel using 2 6 x 3 screws See Figure 4C U Assembly Instructions Model E 2L Step 5 Place the cabinet into location and drive fasteners through the holes and into the zip it or molly inserts already mounted into wall or directly into the structural member if present See Figure 5A If using the molly screws make sure you tighten the screws sufficiently for the molly inserts to properly grip drywall See Figure 5B FIGURE 5A MOLLY A iN euy DRYWALL lt as REAR PANEL OF CABINET FIGURE 5B Step 6 Using the provided silicone apply silicone to th

Download Pdf Manuals

image

Related Search

Related Contents

Zanussi DE 4744 Instruction Booklet  P7225 2.5GHz 10X Active Probe User Manual  Threshold 34 in Round Outdoor Firebowl with Slate  Canon VB-M640V    Logique de la conception  Nuovo Progetto italiano 1 IWB Software USER`S MANUAL  GE AEW18* Cooktop User Manual  

Copyright © All rights reserved.
Failed to retrieve file