User Guide
Contents
1. Power GPS PERFORMANCE On Low battery SPOT uses an advanced GPS chipset with extremely high sensitivity to give you maximum performance While the SPOT message transmitter is also very high quality there may be times when SPOT will have a GPS signal but the message vvon t be able to reach the satellites due to environmental blockage Make sure that you have a clear view of the sky at all times 19 20 SEGTION 5 CARE AND SUPPORT For reliable performance use AAA Energizer Ultimate Lithium 8x batteries L92 NiMH rechargeable batteries or line power Using USB line power will NOT charge rechargeable batter les The power light will blink red when batteries are low Colder conditions and extreme heat can impact battery life Always carry an extra set of batteries with you Non lithium batteries will work with SPOT but are not recommended for optimal performance Test your SPOT device before each trip by sending a Check In message to yourself SPOT performance and battery life may be degraded in operating environments where the SPOT GPS chip must take a longer time to acquire your GPS location such as trying to send a message under dense foliage For optimal performance operate your SPOT with the logo side up in clear view of the sky Using non recommended battery types may degrade the performance of your SPOTs message transmission SPOT Gen3 is designed to be rugged for outdoor use Dropping the unit on hard surfaces2. reliability In some modes this means multiple attempts to send the same message while in other modes it means regularly updating GPS coordinates and sending a new message with the most up to date information GPS The GPS light notifies you whether or not SPOT is able to see the GPS satellites and obtain a GPS location e Green The GPS light blinks green if SPOT sees the GPS satellites and is looking for has found your GPS location e Red The GPS light blinks red if SPOT cannot see the GPS satellites and or cannot find your GPS location If the GPS light blinks red you should move to a location with a clearer view of the sky PLACEMENT OF YOUR SPOT The placement of your SPOT can make a difference For best reception always keep the logo pointed towards the sky the satellite antenna is located under the logo MESSAGE INDIGATORS For all functions SPOT lets you know what it is doing INDICATOR GPS BLINKING GREEN Searching for GPS signal BLINKING RED GPS location fix failed move to a new location Message Sending Message transmission schedule in progress Last message was not sent Check In or Custom Message Message sequence in progress Message sequence has been cancelled Help SPOT in Help SPOT Assist mode Help SPOT Assist has been cancelled S O S S O S is engaged S O S has been cancelled Tracking SPOT in Track mode Track sequence has been cancelled
3. cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures a Reorient or relocate the receiving antenna b Increase the separation between the equipment and receiver c Connect the equipment into an outlet on a circuit different from that to which the receiver is connected d Consult the dealer or an experienced radio TV technician for help Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This Class B digital apparatus complies with Canadian ICES 003 This device complies with Industr
4. to GEOS who facilitates search and rescue Example Snake bite broken leg CHECK IN Let contacts know where you are and that you re okay with a pre programmed message Automatically send and save your location and allow contacts to track your progress using Google Maps Press the power button to turn SPOT on LEDs will illuminate Press and hold the power button until it blinks rapidly to turn SPOT off GPS LIGHT Notifies you whether or not SPOT is able to see the GPS satellites amp obtain your GPS location MESSAGE SENDING LIGHT Notifies you whether or not your most recent message was transmitted SECTION 3 USING SPOT POWER There are three ways you can power your SPOT 4 AAA Energizer Ultimate Lithium 8x batteries included 4 AAA NiMH rechargeable batteries or with line power through a 5v USB connection Keep your batteries installed even when using line power to ensure proper system performance in the event line power should fail Please note NIMH batteries cannot be charged within the SPOT unit using line power and SPOT Gen3 is not waterproof while being line powered TO TURN SPOT ON Simply locate the Power button on the upper left corner of the device press and hold the button lights will illuminate TO TURN SPOT OFF Press and hold the Power button until the Power light blinks rapidly COO SELF TEST SPOT performs a self test when you initially turn on your device During self test all lights will b
5. while not recommended should not damage it but can cause a loss of power and may damage the batteries Power loss turns off your SPOT stopping any current mode of operation If dropped SPOT recommends replacing the batteries for optimal performance COVERAGE SPOT works around the world including virtually all of North America Europe Australia and portions of South America Northern Africa and Asia as well as hundreds of thousands of square miles off shore of these areas It is important that you check SPOT s coverage for your destination before traveling Visit FindMeSPOT com Coverage to view the latest coverage map OPERATING CONDITIONS AND CLIMATE Your SPOT is designed for adventure However like all electronic devices it has its limits SPOT relies on GPS and low earth orbit satellites to fix your location and send your messages The transmitter located underneath the SPOT logo needs to have an unobstructed view of the sky either outdoors or in a glass enclosed area such as a vehicle dashboard For safety keep the following in mind regarding the care and usage of SPOT e IPX7 waterproof Up to a depth of 1 m for up to 30 minutes SPOT is not waterproof when being line powered e Operating temperatures 22 F to 140 F 30 C to 60 C e Operating altitude 328 ft to 21 320 ft 100 m to 6 500 m e Humidity and Salt Fog rated e f you exceed 700 mph Mach 1 GPS accuracy degrades CONTACTS Additional charges may apply in som
6. SPOT GEN3 USER GUIDE HOW SPOT WORKS GPS satellites provide signals SPOT determines your GPS location and sends your location and pre programmed message to communication satellites Communication satellites relay your message to specific satellite antennas around the world Satellite antennas and a global network route your location and message to the appropriate network Your location and messages are delivered according to your instructions via email text message or emergency notification to the GEOS International Emergency Response Coordination Center f A TRACK haf TRACK H H 7 d TRACK J w TRACK 9 TRACK LS 10 E es TRACK my S ga vi gji TRACK 12 nd WIR gt Google Powered by Google Maps When SPOT sends a text or email message to one of your contacts or to GEOS it includes your GPS coordinates and a web link email only to view your location using Google Maps SECTION 1 WELCOME Welcome to the SPOT Family SPOT devices provide satellite based messaging capability so everyone who enjoys the great outdoors can communicate from remote locations around the globe beyond the reach of cell phones Pretty cool huh HERE ARE A FEW IMPORTANT THINGS TO REMEMBER ABOUT YOUR SPOT GEN3 D SPOT needs a clear view of the sky to obtain a GPS signal to provide the most accurate location information SPOT is not as reliable at the bottom of a deep canyon in a cave or in
7. com DECLARATION OF CONFORMITY FOR EUROPEAN CUSTOMERS Hereby Globalstar Europe Satellite Services Ltd declares that this SPOT Gen3 is in compliance with the essential requirements and other relevant provisions of Directive 1995 5 EC The declaration of conformity may be consulted at FindMeSPOT com EXCEPT AS PROVIDED ABOVE THE PRODUCT IS SOLD AS IS WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES FOR THE PRODUCT WHATSOEVER INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES REGARDING THE CONDITION DESIGN SPECIFICATIONS WORKMANSHIP MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCT OR ANY WARRANTIES THAT THE PRODUCT IS FREE FROM LATENT DEFECTS OR DEFICIENCIES OR THAT THE PRODUCT IS FREE FROM INFRINGEMENT OF ANY PATENT TRADEMARK COPYRIGHT OR PROPRIETARY RIGHT OF ANY THIRD PARTY AND SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED THIS LIMITED WARRANTY PROVIDES THE SOLE AND EXCLUSIVE REMEDY FOR ANY DEFECTS IN THE PRODUCT IN NO EVENT SHALL WE BE LIABLE FOR ANY INDIRECT CONSEQUENTIAL SPECIAL INCIDENTAL OR PUNITIVE DAMAGES WHETHER IN CONTRACT TORT NEGLIGENCE STRICT LIABILITY OR OTHERWISE OUR LIABILITY IS LIMITED TO THE AMOUNT YOU PAID FOR THE PRODUCT THAT IS THE SUBJECT OF A CLAIM THE APPLICABILITY OF THE ABOVE LIMITATIONS AND EXCLUSIONS MAY VARY FROM STATE TO STATE OR COUNTRY TO COUNTRY This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not
8. e regions Standard text messaging charges from your mobile phone provider may also apply CLEANING Follow these general rules when cleaning the outside of your SPOT e Make sure the power is OFF e Use a damp soft lint free cloth and avoid excess moisture near buttons or openings e Do not use aerosol sprays solvents alcohol or abrasives e Do not attempt to open the SPOT case TROUBLESHOOTING SPOT performs a self diagnostic test each time it is powered on SPOT recommends that you send and verify a Check In message before each trip This also allows you to evaluate your entire messaging system from the operational condition of the SPOT to the readiness of those on your contact list For more information visit the FAQ section on FindMeSPOT com 21 24 LEARN MORE Visit FindMeSPOT com for the latest information on SPOT Gen3 and other SPOT products and services You can find more helpful tips testimonials and videos If you can t find what you re looking for please do not hesitate to contact us CUSTOMER CARE Visit FindMeSPOT com Care or call e North American Customers 866 0K1 SPOT 866 651 7768 e European Customers Tel 353 1 290 9505 LIMITED WARRANTY Your SPOT has a Limited Warranty for 12 months 24 months for European Customers from the date of purchase against defects in materials and workmanship only For full details regarding the Limited Warranty and warranty claim procedures visit SPOTwarranty com or FindMeSPOT
9. een The GPS light will blink green when SPOT sees the GPS satellites and will continue blinking while obtaining your GPS location Once your GPS location is obtained the GPS light and Message Sending light will both blink green indicating that SPOT is sending your track as a waypoint The Message Sending light continues to blink green until the next scheduled message or until the mode ends If no GPS signal is found the GPS light will blink red If possible you should move to a location with a clearer view of the sky If no GPS location is found within 4 minutes SPOT will not send this particular waypoint The GPS light will blink red for approximately 15 seconds the Message Sending light will blink red until SPOT is ready to send the next waypoint SPOT will try to obtain your GPS coordinates again at your next scheduled track interval TO CANCEL To stop sending track messages press and hold the Track button until the light blinks red or power off SPOT MOTION ACTIVATED TRACKING SPOT Gen3 tracking is smarter than ever A built in vibration sensor sends tracks only when you are moving When the device is stationary for more than five minutes SPOT Gen3 will enter Suspended Track mode SPOT Gen3 will automatically send one more track from your resting location While at rest SPOT Gen3 will not send tracks Tracking will automatically resume after the vibration sensor detects the unit has begun moving again BASIC TRACKING With Basic Tracki
10. ences qui peuvent provoquer un fonctionnement ind sirable du p riph rique Cet appareil respecte les exigences de Radio Astronomie de limitation d mission d onde d fini par l accord de la Foundation Nationale de Science Globalstar de 2001 Il est compatible avec CFR25 213 Cet appareil ajuste automatiquement sa fr quence de transmission en fonction de son emplacement et est conforme aux exigences r glementaires internationales C 13130 amp e TM Ready for Adventure FINdMeSPOT com 2013 SPOT LLC For more information visit FindMeSPOT com The official language of this User Guide is English The translations are provided for your convenience only In the case of any contradiction between a translation and the English the English version shall take precedence USERG ENG VI ROHS and WEEE compliant Certified to FCC and CE emissions immunity and safety regulations Meets FCC part 25 regulations Canada type approval CISPR Publication 22 1985 Ist Edition RTTE Directive 1999 EC and IEC 60950 safety standard
11. il messages also include a link to view your location using Google Maps With SPOT Assist roadside or maritime professional services will receive your Help message and current GPS location to dispatch assistance For more information on SPOT Assist including pricing please visit FindMeSPOT com Assist SS SS sa K T USING THE HELP FUNCTION To send a Help message open the protective flap then press and hold the Help button until the light blinks green The GPS light will blink green when SPOT sees the GPS satellites and while obtaining your GPS location Once your GPS location is obtained SPOT sends your Help message with GPS location every five minutes for one hour The GPS light and Message Sending light will both blink green The Message Sending light continues to blink green until the next scheduled message or until the mode ends If no GPS signal is found the GPS light will blink red If possible you should move to a location with a clearer view of the sky SPOT will keep looking for your GPS location for up to 4 minutes If no GPS location is found in 4 minutes SPOT sends your message without GPS location the GPS light will blink red and the Message Sending light will blink green in unison TO CANCEL Press and hold the Help button until the Help light blinks red Leave SPOT on while the Help cancel message is sent turning off your SPOT DOES NOT cancel the Help message When it is finished the Message Sending light wil
12. in the event line power should fail AT FINDMESPOT COM VVHAT YOU NEED e Personal contact information e Emergency contact information e Valid email address e Credit card information e SPOT electronic serial number ESN and authorization code ACCOUNT SETUP 1 Go to FindMeSPOT com Activate 2 Existing SPOT customers should login to their current SPOT account to add their new device New customers will need to select Set Up New Account 3 Follow the instructions given within the activation portal do not skip forms or pages 4 Choose the services you wish to add like the new upgraded Unlimited and Extreme Tracking to your SPOT device and confirm your order to finish the activation process SERIAL NUMBER ESN AND AUTHORIZATION CODE These codes are located inside the battery compartment of your SPOT Gen3 You will need these codes when A ES Re TITI ESN 0 0000009 Auth 00000000 ELECTRONIC SERIAL NUMBER ESN AUTHORIZATION CODE GPS LIGHT POWER LIGHT MESSAGE SENDING LIGHT HELP SPOT S 0 S ASSIST a a CHECK IN CUSTOMMESSAGE Me SECTION 3 FUNCTIONS HELP SPOT ASSIST Request help from your friends amp family at your GPS location Or ask for help from professional assistance organizations Example Flat tire need a lift CUSTOM MESSAGE Let contacts know where you are by sending a pre programmed message with your GPS location In an emergency send an S 0 S with your GPS location
13. l blink green indicating it has sent the cancel message HOW SPOT PRIORITIZES HELP Help SPOT Assist messages are a high priority for SPOT Help SPOT Assist takes priority over Check In Custom Message and Tracking functions Pressing the S O S button takes priority over the Help SPOT Assist message in order to ensure the S O S message is sent There is no need to cancel any other modes to enter into Help or S O S mode 14 CHECK IN AND CUSTOM MESSAGE Let your contacts know where you are by sending a message with your GPS location With the ability to pre program your messages the possibilities are endless Check In and Custom Message functions work the same way This gives you the flexibility to send different messages to different contacts or tailor messages for a specific purpose Let your contacts know you ve made camp for the night reached your goal or are doing fine With the push of a button your contacts receive your pre programmed message by text or email complete with your GPS location USING THE CHECK IN OR CUSTOM MESSAGE FUNCTION Press and hold the Check In or Custom Message button until the function light blinks green The GPS light will blink green when SPOT sees the GPS satellites and will continue blinking while obtaining your GPS location Once your GPS location is obtained SPOT sends your message with GPS location The GPS light and Message Sending light will both blink green The message is sent three times o
14. l subsequent messages SPOT will keep looking for your GPS location for up to 4 minutes The S 0 S message will send every 5 minutes with or without GPS until cancelled or the power source runs out TO CANCEL S 0 S Press and hold the S 0 S button until the light blinks red Let SPOT work until the S 0 S button stops blinking red to finish sending the cancellation message The Message Sending light will blink green indicating it has sent the cancel message Turning off your SPOT while in S 0 S mode DOES NOT send an S 0 S cancel message HOW SPOT PRIORITIZES 0 S S O S messages are the top priority for SPOT When you send an S 0 S message your SPOT stops sending all other messages to allow for uninterrupted transmission of the S O S message SPOT TIP Let your emergency contacts know when you are planning a trip When GEOS receives an S O S message they will first call your contacts asking for pertinent details like your itinerary planned route or other identifiers This information helps GEOS in working with local authorities to evaluate the appropriate response team needed and send rescue personnel fast 11 12 HELP SPOT ASSIST For non life threatening situations ask for help from friends and family or gain a direct line to professional assistance providers using SPOT Assist additional service plan required When you press Help your contacts will receive SMS text or email messages with your GPS coordinates Ema
15. link green in a rotating manner to indicate self test is in progress If all visible lights flash red the SPOT self test has found a failure please call customer care If the Power and GPS light blink red in unison SPOT has a GPS failure but may still be able to transmit an S O S or Help SPOT Assist message without your GPS location INITIAL SYSTEM TEST Perform an initial system test to evaluate your messaging system from the operational condition of the SPOT to the readiness of those you ve chosen to receive your messages 1 Once you have set up the message contacts for SPOT Gen3 in your FindMeSPOT com account go outside where SPOT has a clear view of the sky in all directions 2 Turn SPOT on press and hold the Power button lights will illuminate 3 Press and hold the Check In button until the function light blinks green 4 Leave SPOT outdoors The GPS light will blink green as SPOT acquires a GPS fix Once SPOT acquires your GPS location the Message Sending light and GPS light will blink green in unison for 15 seconds to notify you that your message is being transmitted with your GPS location The Message Sending light will continue to blink green until the message cycle is complete E Verify that the message was received in the email or SMS account s in your Check In contact list You can also view your sent messages in your account at FindMeSPOT com SPOT TIP Add your email or phone number as a contact for system testing
16. nces nuisibles aux communications radio Rien ne garantit cependant que l interf rence ne se produira pas dans une installation particuli re Si cet quipement provoque des interf rences nuisibles la r ception radio ou de t l vision qui peut tre d termin en comparant et en l teignant l utilisateur est encourag essayer de corriger les interf rence par une ou plusieurs des mesures suivantes a R orienter ou d placer l antenne de r ception b Augmenter la distance entre l quipement et le r cepteur c Branchez l appareil dans une prise sur un circuit diff rent de celui auquel le r cepteur est connect d Consultez votre revendeur ou un technicien radio TV pour assistance Les changements ou modififications cet appareil sans express ment approuv e par la partie responsable de conformit pourraient annuler l autorit de l utilisateur de faire fonctionner cet quipement Avertissement Les changements ou modifications non express ment approuv s par la partie responsable de la conformit pourraient annuler l autorisation de l utilisateur utiliser l quipement Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada Cet appareil est conforme avec Industrie Canada exempt de licence Rss standard s Son fonctionnement est soumis aux deux conditions suivantes 1 cet appareil ne peut causer d interf rences et 2 cet appareil doit accepter toute interf rence y compris des interf r
17. ng messages are sent every 10 minutes for 24 hours while moving or until cancelled To re engage Tracking after 24 hours has passed press and hold the Track button until the function light blinks green UNLIMITED AND EXTREME TRACKING SPOT Gen3 s new enhanced tracking options allow you to set it and forget it Send track messages every 2 1 2 5 10 30 or 60 minutes depending on your plan and preference for as long as your SPOT is powered on or until the batteries run out To set your rate of tracking sign in to your SPOT account at FindMeSPOT com and choose view edit SPOT Features from the My SPOT Devices tab PLEASE NOTE making any change to the rate of tracking requires you to reconfigure your device to update the settings Y gt Keep track of all of your adventures by uploading your tracking messages to a LLO SAN SPOT Adventures Share your trips with friends and family upload pictures and tell the story of just how amazing the sunset is from the top of the peak UJI e 18 SECTION 4 SYSTEM FUNCTION AND INDICATORS SPOT is designed to provide outstanding quality and reliability For optimum reception always place your SPOT with the logo side up in clear view of the sky Reception can be inhibited due to hills buildings metal roofs or other obstructions so it is normal that some messages may not go through That is why SPOT automatically sends multiple messages in every mode giving you excellent overall
18. so you can hit the trail faster S r E pr S 0 S SPOT s S O S function should only be used for critical life threatening situations Pressing the S O S button sends an alert directly to GEOS International Emergency Response Coordination Center IERCC GEOS notifies the appropriate emergency responders of your 0 S based on GPS location and personal information Depending on your GPS location responders may include local police highway patrol the Coast Guard your country s embassy or consulate other emergency response centers or search and rescue teams Sending false S O S messages may subject you to liability for additional charges 10 USING THE 0 S FUNCTION To send an S O S alert open the protective flap then press and hold the S O S button until the function light blinks green The GPS light will blink green when SPOT sees the GPS satellites and while obtaining your GPS location Once your GPS location is obtained SPOT sends your S O S message with GPS location The GPS light and Message Sending light will both blink green The Message Sending light continues to blink green until the next scheduled message to notify you that your most recent message was transmitted If no GPS signal is found the GPS light will blink red If possible you should move to a location with a clearer view of the sky The first message will be sent within one minute after activation with or without your GPS location For al
19. ver a 20 minute period to the SPOT network this is to ensure maximum reliability in getting your message out Only one message will be sent to your contacts The Message Sending light continues to blink green until the next scheduled message or until the mode ends If no GPS signal is found the GPS light will blink red If possible you should move to a location with a clearer view of the sky SPOT will keep looking for your GPS location for up to 4 minutes If no GPS location is found in 4 minutes SPOT does not send your message To try again simply press and hold the function button If the message does not send the Message Sending light will blink red Check In or Custom messages can be sent while Tracking TO CANCEL You can end the transmission of a Check In or Custom Message by pressing and holding the function button until the light blinks red This action does not cancel any message already transmitted i i Gra PRES 16 TRACKING With SPOT Gen3 your friends and family can track your progress in near real time using SPOT Shared Pages with Google Maps giving them a virtual breadcrumb trail of your adventure New enhanced tracking options allow you to choose the rate of tracking that fits your adventure by upgrading to our Unlimited or Extreme Tracking Plans additional service fees may apply learn more at FindMeSPOT com USING THE TRACKING FUNCTION Press and hold the Track button until the function light blinks gr
20. very dense woods Sunshine is more fun anyway D Orienting SPOT so that the SPOT logo is facing up toward the sky will improve performance as the antenna is located directly under the logo The coolest adventurers place SPOT on their backpacks by In order to ensure best performance do not use SPOT immediately adjacent to other GPS devices To begin using SPOT we recommend you spend a few minutes reading through this User Guide then visit FindMeSPOT com to select a service plan and activate your SPOT device SECTION 2 GETTING STARTED Your SPOT Gen3 requires an active SPOT subscription to communicate To do this simply activate your device using the instructions outlined below WITH YOUR SPOT WHAT YOU NEED e Your SPOT Gen3 e One of these three power sources 4 AAA Energizer Ultimate Lithium 8x batteries L92 included 4 AAA Energizer NiMH rechargeable batteries NH12 Line Power with a bv USB connection e User Guide INSTALL THE INCLUDED BATTERIES 1 Loosen the screws to open the battery cover 2 Write down the ESN and Authorization Code for use during service activation 3 Install 4 AAA Energizer Ultimate Lithium 8x batteries or NIMH rechargeable batteries 4 Replace cover tighten screws with a screwdriver or coin lt is important that you fully tighten the battery cover to maintain SPOT s waterproof seal 5 Keep your batteries installed even when using line power to ensure proper system performance
21. y Canada license exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device This device complies with the requirements for Radio Astronomy Site avoidance as specified by the Globalstar National Science Foundation agreement of 2001 It is compliant with CFR25 213 This device automatically adjusts its transmission frequency according to its location and is compliant with international regulatory requirements 13130 amp 29 26 Cet appareil est conforme la partie 15 des r gles de la FCC Son fonctionnement est soumis aux deux conditions suivantes 1 Ce dispositif ne peut pas causer de brouillages ind sirables et 2 Cet appareil doit accepter tous les signaux recus y compris les interf rences pouvant entrainer un fonctionnement ind sirable Conformit aux normes FCC Cet quipement a t test et trouv conforme aux limites pour un dispositif num rique de classe B conform ment a la Partie 15 des r glements de la FCC Ces limites sont con ues pour fournir une protection raisonnable contre les interf rences nuisibles dans une installation r sidentielle Cet quipement g n re utilise et peut mettre des fr quences radio et s il n est pas install et utilis conform ment ment aux instructions du fabricant peut causer des interfere
Download Pdf Manuals
Related Search